The effect of crosslinked networks with poly(ethylene glycol) on sulfonated polyimide for polymer electrolyte membrane fuel cell

To investigate the effect of crosslinking by a hydrophilic group on a sulfonated polyimide electrolyte membrane, sulfonated polyimide end‐capped with maleic anhydride was synthesized using 1,4,5,8‐naphthalenetetracarboxylic dianhydride, 4,4′‐diaminobiphenyl, 2,2′‐disulfonic acid, 2‐bis [4‐(4‐aminophenoxy)phenyl] hexafluropropane and maleic anhydride. The sulfonated polyimides end‐capped with maleic anhydride were self‐crosslinked or crosslinked with poly(ethylene glycol) diacrylate. A series of the crosslinked sulfonated polyimides having various ratios of sulfonated polyimide and poly(ethylene glycol) diacrylate were prepared and compared with uncrosslinked and self‐crosslinked sulfonated polyimides. The synthesized sulfonated polyimide films were characterized for FTIR spectrum, thermal stability, ion exchange capacity, water uptake, hydrolytic stability, morphological structure, and proton conductivity. The formation of sulfonated polyimide was confirmed in FTIR spectrum. Thermal stability was good for all the sulfonated polyimides that exhibited a three‐step degradation pattern. Ion exchange capacity was the same for both the uncrosslinked and the self‐crosslinked sulfonated polyimides (1.30 mEq/g). When the crosslinked sulfonated polyimides with poly(ethylene glycol) were compared, the ion exchange capacity was decreased as 1.27 > 1.25 > 1.23 mEq/g and water uptake was increased as 23.8 < 24.0 < 24.3% with the increase in poly(ethylene glycol) diacrylate content. All the crosslinked sulfonated polyimides with poly(ethylene glycol) diacrylate were stable for over 200 h at 80 °C in deionized water. Morphological structure and mean intermolecular distance were obtained by WAXD. Proton conductivities were measured at 30, 50, 70, and 90 °C. The proton conductivity of the crosslinked sulfonated polyimides with poly(ethylene glycol) diacrylate increased with the increase in poly(ethylene glycol) diacrylate content despite the fact that the ion exchange capacity was decreased. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1455–1464, 2005     

Poly(ethylene glycol)‐based amphiphilic model conetworks: Synthesis by RAFT polymerization and characterization

Poly(ethylene glycol) (PEG)‐containing quasi‐model amphiphilic polymer conetworks (APCNs) were prepared by reversible addition fragmentation chain transfer (RAFT) polymerization using α,ω‐bis(2‐cyanoprop‐2‐yl dithiobenzoate)‐PEG as a bifunctional RAFT macrochain transfer agent (macro‐CTA) and stepwise additions of a hydrophobic monomer and a crosslinker (crosslinker: macro‐CTA = 10:1, reaction time 24 h). Three different types of monomers, methyl methacrylate (MMA), n‐butyl acrylate and styrene, were employed as the hydrophobic monomers, whereas ethylene glycol dimethacrylate, ethylene glycol diacrylate and 1,4‐divinylbenzene served as the respective crosslinkers. PEG homopolymer hydrophilic quasi‐model networks were also prepared by RAFT‐polymerizing the three crosslinkers directly onto the two active ends of the PEG‐based macro‐CTA. From the three ABA triblock copolymers prepared, the MMA‐containing one was obtained at the highest polymerization yields. The crosslinking yields of the three ABA triblock copolymers with the corresponding crosslinkers were higher than those of the PEG‐based macro‐CTA with the same crosslinkers. The degrees of swelling (DSs) of all conetworks were measured in water and in tetrahydrofuran (THF). The DSs of the APCNs in THF were higher than those in water, whereas the reverse was true for the DSs of the hydrophilic homopolymer networks. Finally, the aqueous DSs of the APCNs were lower than those of the corresponding hydrophilic homopolymer networks. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7556–7565, 2008     

Novel biobased photo‐crosslinked polymer networks prepared from vegetable oil and 2,5‐furan diacrylate

Novel biobased crosslinked polymer networks were prepared from vegetable oil with 2,5‐furan diacrylate as a difunctional stiffener through UV photopolymerization, and the mechanical properties of the resulting films were evaluated. The vegetable oil raw materials used were acrylated epoxidized soybean oil (AESO), acrylated castor oil (ACO), and acrylated 7,10‐dihydroxy‐8(E)‐octadecenoic acid (ADOD). 2,5‐Furan dicarboxylic acid (FDCA), which can be synthesized through the oxidative dehydration of C6 sugars, was identified by the US Department of Energy as one of 12 priority chemicals for establishing the green chemistry industry of the future. 2,5‐Furan dimethanol (bis‐hydroxymethylfuran), which can be derived from FDCA, was used as a starting material to synthesize 2,5‐furan diacrylate, which was used as a biobased comonomer along with AESO, ACO, or ADOD to form photo‐crosslinked polymer networks. The synthesis of acrylate derivatives was confirmed using FT‐IR and ¹H‐NMR spectroscopic techniques. The composition of the reaction mixture was changed to obtain crosslinked polymer networks with various mechanical properties. The addition of 2,5‐furan diacrylate increased the tensile strengths of the polymer films by up to 1.4–4.2 times relative to those obtained without the addition. These fully biobased polymers derived from vegetable oil and sugar can be used as environmentally friendly renewable materials for various applications to replace the existing petroleum‐based polymers currently used. Copyright © 2013 John Wiley & Sons, Ltd.     

Synthesis and characterization of spherical and hemispherical polyepoxide micrometer‐sized particles of narrow size distribution by a single‐step swelling of uniform polystyrene template microspheres with glycidyl methacrylate

Polystyrene template microspheres of narrow size distribution were prepared by dispersion polymerization of styrene in a mixture of ethanol and 2‐methoxy ethanol. Spherical and hemispherical polystyrene/poly(glycidyl methacrylate) microspheres of narrow size distribution were prepared by a single‐step swelling of the polystyrene template microspheres with the swelling solvent monomer glycidyl methacylate, followed by polymerization of the monomer within the swollen template microspheres at 73 °C. Uniform polystyrene/poly(glycidyl methacylate‐ethylene glycol dimethacrylate) polyepoxide composite microspheres were synthesized similarly, substituting glycidyl methacylate for glycidyl methacylate and ethylene glycol dimethacrylate. Uniform crosslinked poly(glycidyl methacylate‐ethylene glycol dimethacrylate) polyepoxide microspheres have been prepared by dissolution of the PS template polymer of the former composite microspheres. Particles with different properties, for example size, size distribution, shape, surface morphology, surface area, and so forth, were prepared by changing various parameters belonging to the swelling and/or polymerization steps, for example, volume of the swelling monomer/s and/or the swelling solvent dibutyl phthalate. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4612–4622, 2007     

Preparation of liquid–crystal thermosets: In situ photopolymerization of oriented liquid–crystal diacrylates

The photoinitiated polymerization of 2-chloro-1,4-phenylene bis[4-[6-(acryloyloxy)hexyloxy]benzoate] (1M) was studied. The monomer 1M exhibited a broad nematic phase between 24.9 and 113.7 °C on a DSC cooling scan. It was oriented in its nematic phase at a substrate coated with polyimide and unidirectionally rubbed with a nylon cloth. During polymerization, the ordering of the liquid–crystal molecules was fixed, yielding a uniaxially crosslinked network. The clear liquid–crystal networks (LCNs) exhibited a birefringence between 0.14 and 0.19, depending on the polymerization temperature. Finally, a nonmesogenic diluent, tetra(ethylene glycol)diacrylate, was mixed with 1M, subsequently decreasing the birefringence of the obtained LCNs. The LCNs containing nonmesogenic diluent exhibited not only a smaller birefringence but also a weaker birefringence dispersion in the visible region. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3929–3935, 1999     

Bioinspired core‐crosslinked micelles from thymine‐functionalized amphiphilic block copolymers: Hydrogen bonding and photo‐crosslinking study

Bioinspired core‐bound polymeric micelles, based on hydrogen bonding and photo‐crosslinking, of thymine have been prepared from poly(vinylbenzylthymine)‐b‐poly(vinylbenzyltriethylammonium chloride). The amphiphilic block copolymer was synthesized by 2,2‐tetramethylpiperidin‐1‐oxyl‐mediated living radical polymerization in water/ethylene glycol solution. Micelle characterization and critical micelle concentration measurements demonstrated that the hydrogen bonding of the attached thymine units stabilizes the micelles. Further, core‐crosslinked polymeric micelles were formed by ultraviolet (UV) radiation showing that the stability of the micelle could be controlled by the UV crosslinking of the attached thymines. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Liquid crystalline epoxides with long lateral substituents: Mechanical and thermal properties

In this work, mechanical and thermal properties of liquid crystalline epoxides (LCEs) with long lateral substituents from 4 to 12 carbon atoms cured with diaminodiphenylmethane were evaluated and analyzed by dynamic mechanical analysis, tensile tests, scanning electron micrographs (SEM), and thermo‐gravimetrical analysis. The experimental results indicated that the Young's modulus and α, β transitions in crosslinked networks are associated with the length of lateral substituents. The plastic deformation in fracture surfaces was observed by SEM. Thermal stability, water and solvent absorption of cured networks was dependent on the length of lateral substituents. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2835–2841, 2007     

On the relevance of the 8‐chain model and the full‐network model for the deformation and failure of networks formed through photopolymerization of multifunctional monomers

Crosslinked networks were synthesized by copolymerization of mono‐functional tert‐butyl acrylate (tBA) with diethyleneglycol dimethacrylate (DEGDMA) or polyethylene glycol dimethacrylates (PEGDMA). By varying the chain length and concentration of the difunctional PEGDMA, we obtained tBA‐PEGDMA copolymer networks while by varying the concentration of difunctional DEGDMA, we obtained tBA‐DEGDMA crosslinked networks. The various materials were submitted to large deformations through uniaxial tension tests. For moderate weight percent of crosslinking agent, up to 20%, the networks showed standard S‐shape stress–strain curves, characteristic of rubber‐like elasticity. Two macromolecular models, the 8‐chain model and the full‐network model, were applied to fit the uniaxial tensile response of the materials. Both models provide good representations of the overall uniaxial stress–strain response of each material. After fitting to stress–strain data, the network models were employed to predict the shear modulus and the elongation at break. Neither the 8‐chain nor the full network model were capable of predicting the failure strain or shear modulus, indicating these models are best used to describe stress–strain relations rather than predict mechanical properties for the network polymers considered here. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1226–1234, 2008     

The influence of diffusion time on the properties of sequential interpenetrating PEG hydrogels

Four sets comprising a total of 16 sequential interpenetrating network (SeqIPN) hydrogels were efficiently fabricated via UV initiated thiol‐ene coupling chemistry and from 2 kDa or 8 kDa primary poly(ethylene glycol) (PEG) networks (S2 and S8). Each primary system delivered four different SeqIPNs constructed after 2, 4, 20, and 44 h diffusion of secondary network PEG precursors, 2 kDa and 8 kDa. This allowed the assessment of both mechanical and swelling properties for a wide range of novel hydrogels ranging from loosely crosslinked SeqIPN 8‐8 to densely crosslinked SeqIPN 2‐2 systems. All gel fractions of secondary networks were above 83% and 44 h of diffusion was found sufficient to fully saturate the primary networks. Disperse red functionalized PEGs (2 kDa and 8 kDa) were further used as probes to investigate the diffusion mechanisms. The impact of diffusion time on loosely crosslinked S8 network with a swelling degree of 970% and tensile modulus of 175 kPa displayed a significant change in the final properties. For instance, a 2 h diffusion of 2 kDa PEG precursors generated a SeqIPN 8‐2:2 comprising a secondary network solid content of 34% with a water swelling degree 580% and a tensile modulus of 365 kPa. On saturation, that is, 44 h of diffusion, SeqIPN 2‐8:44 exhibited 64% of secondary network solid content, a swelling capacity of 380% and over fourfold of tensile modulus (758 kPa) when compared with the primary network S8. SeqIPN hydrogel with the highest tensile modulus and lowest degree of water swelling was obtained after 44 h diffusion of 2 kDa PEG precursors within the densely crosslinked S2 primary network. In this case, SeqIPN 2‐2:44 noted a water swelling capability of 280% and a tensile modulus over 1 MPa. The latter was twofold when compared with S2 with a tensile modulus of 555 kPa. Consequently, the diffusion time of secondary network is a promising parameter to control and that enables the fabrication of PEG hydrogels with a wider window of mechanical and swelling properties. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Transport properties of small molecules in zwitterionic polymers

Despite great interests in using zwitterionic polymers for membrane surface modification to enhance antifouling properties, there lacks fundamental understanding of the relationship between polymer structure and water/salt separation properties. In this study, two series of zwitterionic polymers were prepared from sulfobetaine methacrylate and 2‐methacryloyloxyethyl phosphorylcholine. Both are crosslinked by poly(ethylene glycol) diacrylate (PEGDA). These copolymers were thoroughly characterized in terms of sol‐gel fraction, density, glass transition temperature, contact angle, water and salt transport properties, and pure‐gas permeability. Interestingly, the zwitterionic polymers exhibit water sorption and permeability similar to noncharged poly(ethylene glycol)‐based materials. These zwitterionic polymers exhibit lower NaCl diffusivity and permeability and thus higher water/NaCl selectivity than the non‐charged PEG‐based materials at similar water volume fractions, demonstrating their promise for membrane surface modification for desalination and wastewater treatment. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1924–1934     

Solubility and partial molar volume of carbon dioxide and ethane in crosslinked poly(ethylene oxide) copolymer

Experimental solubility and sorptive dilation data are reported for carbon dioxide and ethane in a crosslinked poly(ethylene oxide) (XLPEO) rubbery copolymer. Five different temperatures (253 ≤ T(K) ≤ 308) were considered, with a maximum gas pressure of 2.09 MPa (20.6 atm). The polymer was prepared by photopolymerization of a solution containing 70 wt % poly(ethylene glycol) methyl ether acrylate (PEGMEA) and 30 wt % poly(ethylene glycol) diacrylate (PEGDA). Sorption isotherms were described by the Flory‐Huggins model. For each gas, the Flory‐Huggins interaction parameter was a decreasing function of temperature and did not show a composition dependence. Dilation and sorption data were combined to calculate the partial molar volume (PMV) of the gases in the polymer, which was an increasing function of temperature. Based on a comparison with literature data for a XLPEO homopolymer prepared from pure PEGDA over the same range of operating conditions, an effect of the network composition on both gas solubility and PMV was found. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 456–468, 2010     

Impact of poly(ɛ‐caprolactone) architecture on the thermomechanical and shape memory properties

We report the synthesis of linear‐ and brush‐type poly(?‐caprolactone) (PCL) networks and investigate their thermal, mechanical, and shape memory behavior. Brush‐PCLs are prepared by ring‐opening metathesis polymerization (ROMP) of a norbornenyl‐functionalized ?‐caprolactone macromonomer (MM‐PCL) of different molecular weights. The linear analog, diacrylate end‐functionalized PCL (linear‐PCL), having comparable molecular weight of side chain of brush‐PCL is also synthesized. These polymers are thermally cured by a radical initiator in the presence of poly(ethylene glycol) diacrylate crosslinker. Thermal and linear viscoelastic properties as well as shape memory performance of the resulting PCL networks are investigated, and are significantly impacted by the PCL architecture. Therefore, our work highlights that tailoring macromolecular architecture is useful strategy to manipulate thermal, mechanical, and resulting shape memory properties. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 3424–3433     

Michael addition for crosslinking of poly(caprolactone)s

Poly(caprolactone) (PCL) networks have received significant attention in the literature because of many emerging potential applications as biodegradable materials. In this study, the Michael addition reaction was used for the first time to synthesize biodegradable networks using crosslinking of acetoacetate‐functionalized PCL (PCL bisAcAc) oligomers with neopentyl glycol diacrylate. Hydroxyl‐terminated PCL telechelic oligomers with number‐average molecular weights ranging from 1000 to 4000 g/mol were quantitatively functionalized with acetoacetate groups using transacetoacetylation. In addition to difunctional PCL oligomers, hydroxyl‐terminated trifunctional star‐shaped PCL oligomers were functionalized with acetoacetate groups. Derivatization of the terminal hydroxyl groups with acetoacetate groups was confirmed using FTIR spectroscopy, ¹H NMR spectroscopy, mass spectrometry, and base titration of hydroxyl end groups. PCL bisAcAc precursors were reacted with neopentyl glycol diacrylate in the presence of an organic base at room temperature. The crosslinking reactions yielded networks with high gel contents (>85%). The thermomechanical properties of the networks were analyzed to investigate the influence of molecular weight between crosslink points. The glass transition and the extent of crystallinity of the PCL networks were dependent on the molecular weight of the PCL segment. Dynamic mechanical analysis indicated that the plateau modulus of the networks was dependent on the molecular weight of PCL, which was related to the crosslink density of the networks. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5437–5447, 2009     

Ionic IPNs as novel candidates for highly conductive solid polymer electrolytes

Five ionic imidazolium based monomers, namely 1‐vinyl‐3‐ethylimidazolium bis(trifluoromethylsulfonyl)imide (ILM1), 1‐vinyl‐3‐(diethoxyphosphinyl)‐propylimidazolium bis(trifluoromethylsulfonyl)imide (ILM2), 1‐[2‐(2‐methyl‐acryloyloxy)‐propyl]‐3‐methylimidazolium bis(trifluoromethylsulfonyl)imide (ILM3), 1‐[2‐(2‐methyl‐acryloyloxy)‐undecyl]‐3‐methylimidazolium bis(trifluoromethylsulfonyl)imide (ILM4), 1‐vinyl‐3‐ethylimidazolium dicyanamide (ILM5) were prepared and used for the synthesis of linear polymeric ionic liquids (PILs), crosslinked networks with polyethyleneglycol dimethacrylate (PEGDM) and interpenetrating polymer networks (IPNs) based on polybutadiene (PB). The ionic conductivities of IPNs prepared using an in situ strategy were found to depend on the ILM nature, T_g and the ratio of the other components. Novel ionic IPNs are characterized by increased flexibility, small swelling ability in ionic liquids (ILs) along with high conductivity and preservation of mechanical stability even in a swollen state. The maximum conductivity for a pure IPN was equal to 3.6 × 10^?5 S/cm at 20 °C while for IPN swollen in [1‐Me‐3‐Etim] (CN)₂N σ reached 8.5 × 10^?3 S/cm at 20 °C or 1.4 × 10^?2 S/cm at 50 °C. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4245–4266, 2009     

Fluorinated bio‐acceptable polymers via an ATRP macroinitiator approach

Polymers derived from bio‐acceptable poly(methyl methacrylate) (PMMA), poly(2‐methoxyethyl acrylate) (PMEA), and poly(oligo(ethylene glycol) methyl ether methacrylate) (PPEGMA) have been prepared via atom transfer radical polymerization (ATRP) utilizing an initiator prepared from a fluoroalkoxy‐terminated oligoethylene glycol. Polymerizations are controlled as seen by both linear first‐order kinetics and molecular weight evolution coupled with low polydispersities (<1.25) with respect to conversion. A range of ligands have been used depending upon the nature of the monomer: N‐(n‐propyl)‐2‐pyridyl‐methanimine with the methacrylates MMA and PEGMA and 1,1,4,7,10,10‐hexamethyltriethylene tetramine (HMTETA) with MEA. In all cases the use of the fluorinated initiator results in a lower apparent rate of propagation (k_p^app) as compared with the more conventional and nonfluorinated initiator, ethyl 2‐bromoisobutyrate. The initiator generally also serves as an internal plasticizer lowering the glass transition temperature from the parent polymers. The surface characteristics of the fluoroinitiator containing polymers are altered compared with the nonfluorinated analogues. This is reflected in a significant increase in the advancing water contact angles of all fluoro‐containing polymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5770–5780, 2007     

Novel AB crosslinked polymer networks from telechelic 4‐vinylbenzyl carbamate terminated polyurethanes and different vinyl monomers

Novel AB crosslinked polymer (ABCP) networks were synthesized from telechelic 4‐vinylbenzyl carbamate terminated polyurethanes and monomers such as styrene, 4‐vinylpyridine, methyl methacrylate and butyl acrylate. Telechelic 4‐vinylbenzyl carbamate terminated polyurethanes were synthesized from polypropylene glycol‐based NCO‐terminated polyurethane and vinylbenzyl alcohol. Effect of changing the molecular weight of polypropylene glycol on the static and dynamic mechanical properties of ABCP networks from polyurethane‐polymethyl methacrylate was studied in detail. Dynamic mechanical thermal analysis results show that polymethyl methacrylate and polystyrene‐based ABCPs have good damping over a broad temperature range. ABCP networks prepared from 4‐vinylbenzyl carbamate terminated polyurethane and different monomers such as methyl methacrylate, butyl acrylate and styrene exhibit single tan δ_max value which implies excellent interlocking between the two polymers present in the ABCP networks. Static mechanical studies showed that methyl methacrylate and styrene‐based ABCP networks exhibit better tensile properties compared to other ABCP networks from butyl acrylate and 4‐vinyl pyridine monomers. Thermogravimetric analysis results revealed that the ABCP networks showed an improved thermal stability. Copyright © 2009 John Wiley & Sons, Ltd.     

Influence of varying hard segments on the properties of chemically crosslinked moisture‐cured polyurethane‐urea

Polyurethane prepolymers are widely used in the reactive hot melt adhesives and moisture‐cured coatings. The chemically crosslinked moisture‐cured formulation based on PEG‐1000 and isophorone diisocyanate was prepared with NCO/OH ratio of 1.6:1.0. Trimethylol propane was used as a crosslinking agent. The excess isocyanate of the prepolymer was chain extended in the ratio of 2:1 (NCO/OH) with different aliphatic diols, and 4:1 with different aromatic diamines. The polymer network maturation during moisture cure was followed by dynamic mechanical thermal analyzer (DMTA) instrument. The thermal and dynamic mechanical properties of the crosslinked polymers were evaluated using thermogravimetric analysis, differential scanning calorimetric analysis and DMTA. Surface properties were evaluated through angle‐resolved X‐ray photoelectron spectroscopy. The present article discusses the physical properties of moisture‐cured polyurethane‐urea (MCPU) containing chemical crosslinks in the hard segment. The complete moisture‐cured polymers showed amorous results toward room temperature modulus, tensile strength, hardness, thermal stability, and transparency. The surface properties showed the enrichment of soft segments. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 102–118, 2006     

Preparation and properties of ionic‐liquid‐containing poly(ethylene glycol)‐based networked polymer films having lithium salt structures

Ionic‐liquid‐containing polymer films were prepared by swelling poly(ethylene glycol)‐based networked polymers having lithium salt structures with an ionic liquid, 1‐ethyl‐3‐methylimidazolium bis(fluorosulfonyl)imide (EMImFSI), or with an EMImFSI solution of lithium bis(trifluoromethanesulfonyl) imide (LiTFSI). Their fundamental physical properties were investigated. The networked polymer films having lithium salt structures were prepared by curing a mixture of poly(ethylene glycol) diglycidyl ether and lithium 3‐glycidyloxypropanesulfonate or lithium 3‐(glycidyloxypropanesulfonyl)(trifluoromethanesulfonyl)imide with poly(ethylene glycol) bis(3‐aminopropyl) terminated. The obtained ionic‐liquid‐containing films were flexible and self‐standing. They showed high ionic conductivity at room temperature, 1.16–2.09 S/m for samples without LiTFSI and 0.29–0.43 S/m for those with 10 wt % LiTFSI. Their thermal decomposition temperature was above 220 °C, and melting temperature of the ionic liquid incorporated in the film was around ?16 °C. They exhibited high safety due to good nonflammability of the ionic liquid. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and characterization of novel degradable photocrosslinked poly(ether‐anhydride) networks

New degradable poly(ether‐anhydride) networks were synthesized by UV photopolymerization. Dicarboxylated poly(ethylene glycol) (PEG) or poly(tetramethylene glycol) (PTMG) was reacted with an excess of methacrylic anhydride to form dimethacrylated macromers containing anhydride linkages. The percent of conversion for the macromer formation was more than 80% at 60 °C after 24 h. ¹H NMR and IR spectroscopies show the presence of anhydride linkages in the macromer. In vitro degradation studies were carried out at 37 °C in PBS with crosslinked polymer networks formed by UV irradiation. All PEG‐based polymers degraded within 2 days, while PTMG‐based polymers degraded by 50% of the initial weight after 14 days. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1277–1282, 2000     

Crosslinkable polyurethane bearing a methacrylate structure in the side chain

A polyurethane bearing methacrylate groups through urethane linkages was prepared by the addition of 2‐methacryloyloxyethyl isocyanate to the hydroxyl groups in poly(hydroxyurethane) prepared by the polyaddition of a bifunctional cyclic carbonate with 1,12‐diaminododecane. The urethanization proceeded quantitatively in the presence of a catalytic amount of di‐n‐butyltin dilaurate at an ambient temperature, whereas a crosslinked product was obtained from the reaction at 60 °C. The resulting linear polyurethane, bearing a methacrylate structure, was thermally crosslinkable. Its radical copolymerization with vinyl‐type monomers afforded the corresponding crosslinked polymers, whose low glass transition temperatures suggested the flexibility of the polymer chains in the crosslinked product. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3400–3407, 2007