Polymerization of isoprene with η5‐C5H4(tert‐Bu)TiCl3/MAO catalyst

cis‐Selective polymerizations of isoprene with the catalysts composed of η⁵‐C₅H₄(R)TiCl₃ (1; R?H, 2 ; tert‐Bu) and methylaluminoxane were investigated. Both catalysts showed remarkable catalytic activities for the polymerization of isoprene. The polymerization activities were strongly affected by the substituent introduced on cyclopentadienyl ring. Introduction of bulky tert‐butyl group was found to be effective for enhancement of polymerization activity, but the cis‐content of polyisoprene prepared by the 2 /MAO catalyst was lower than that by 1 /MAO catalyst. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1841–1844, 2004     

Anionic copolymerization of styrenic‐tipped macromonomers: A route to novel triblock–comb copolymers of styrene and isoprene

The following triblock–comb copolymers of isoprene (I) and styrene (S)—PS‐b‐(PI‐g‐PI)‐b‐PS, PS‐b‐[PI‐g‐(PI‐b‐PS)]‐b‐PS, and (PS‐g‐PS)‐b‐(PI‐g‐PI)‐b‐(PS‐g‐PS) (where PS is polystyrene and PI is polyisoprene)—with PS contents of 20–30% were synthesized with high‐vacuum techniques and the anionic copolymerization of styrenic‐tipped macromonomers with I and S. The macromonomers, prepared by the reaction of living PI or PS with 4‐(chlorodimethylsilyl) styrene, were used without isolation. Molecular characterization by size exclusion chromatography, size exclusion chromatography/two‐angle laser light scattering, and NMR spectroscopy indicated that the triblock–comb copolymers had high molecular and compositional homogeneity. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4030–4039, 2005     

Melting behavior of polyethylene/α‐olefin copolymers: Narrow composition distribution copolymers and fractions from Ziegler–Natta and single‐site catalyst products

The melting temperature and heat of fusion were measured for an extensive series of compositionally uniform copolymers of ethylene with butene‐1, hexene‐1, and octene‐1. Fractions and whole polymers that exhibited minimal interchain compositional heterogeneity were from commercial copolymers made with either Ziegler–Natta (ZN) or single‐site metallocene catalysts. The present results do not support recent claims that ZN and corresponding metallocene catalyst copolymers melt at significantly different temperatures, nor the implication that comonomer incorporation is “blocky” in ZN copolymers. In five of the six comonomer/catalyst systems the dependencies of the melting temperature on comonomer type and amount were scarcely distinguishable. This common behavior is the same as that for a model random copolymer, so we conclude that most ethylene/α‐olefin copolymers have random distributions of ethylene sequences. The exception in the present study is a metallocene ethylene/butene‐1 copolymer that melts at lower temperatures and apparently has perceptibly alternating sequence distributions. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3416–3427, 2004     

Ethylene–propylene copolymerization with bis(β‐enaminoketonato) titanium complexes activated with modified methylaluminoxane

Ethylene–propylene copolymerization, using [(Ph)NC(R₂)CHC(R₁)O]₂TiCl₂ (R₁ = CF₃, Ph, or t‐Bu; R₂ = CH₃ or CF₃) titanium complexes activated with modified methylaluminoxane as a cocatalyst, was investigated. High‐molecular‐weight ethylene–propylene copolymers with relatively narrow molecular weight distributions and a broad range of chemical compositions were obtained. Substituents R₁ and R₂ influenced the copolymerization behavior, including the copolymerization activity, methylene sequence distribution, molecular weight, and polydispersity. With small steric hindrance at R₁ and R₂, one complex (R₁ = CF₃; R₂ = CH₃) displayed high catalytic activity and produced copolymers with high propylene incorporation but low molecular weight. The microstructures of the copolymers were analyzed with ¹³C NMR to determine the methylene sequence distribution and number‐average sequence lengths of uninterrupted methylene carbons. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5846–5854, 2006     

Ethylene polymerization and copolymerization with a polar monomer using an α‐iminocarboxamide nickel complex activated by trimethylaluminum

An α‐iminocarboxamide nickel complex was activated by trimethylaluminum (TMA) and used in the polymerization of ethylene and its copolymerization with 10‐undecen‐1‐ol. The best activity was observed upon activation with 9 equiv of TMA at a temperature of 26 °C. NMR spectroscopic studies did not show 10‐undecen‐1‐ol incorporation. However, FTIR analyses suggest the incorporation of a very small amount of comonomer, which affects the glass transition temperature, the degree of branching, and the mechanical properties of the materials. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 54–59, 2008     

Ethylene polymerization and copolymerization with 10‐undecen‐1‐ol using the catalyst system DADNi(NCS)2/MAO

The catalyst DADNi(NCS)₂ (DAD = (ArN?C(Me)? C(Me)?ArN); Ar = 2,6‐C₆H₃), activated by methylaluminoxane, was tested in ethylene polymerization at temperatures above 25 °C and variable Al/Ni ratio. The system was shown to be active even at 80 °C and when supported on silica. However, catalyst activity decreased. The catalyst system was also tested in ethylene and 10‐undecen‐1‐ol copolymerization at different ethylene pressures. The best activities were obtained at low polar monomer concentration (0.017 mol/L), using triisopropylaluminum (Al‐i‐Pr₃) to protect the polar monomer. The incorporation of the comonomer increased with the increase of polar monomer concentration. According to ¹³C NMR analyses, all the resulting polyethylenes were highly branched and the polar monomer incorporation decreased as ethylene pressure increased. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5199–5208, 2007     

Copolymerization of Propene and Buta‐1,3‐diene in the Presence of Highly Hindered C2‐Symmetric Zirconocene‐Based Catalyst

Summary: Copolymerizations of propene and buta‐1,3‐diene performed in the presence of rac‐[CH₂(3‐tert‐butyl‐1‐indenyl)₂]ZrCl₂ and methylaluminoxane (MAO) have been investigated. Buta‐1,3‐diene gives prevailingly primary coordination to the metal, producing overall 1,2 units. Cyclopropane and cyclopentane rings, although in low amounts, are also obtained. The presence of butadiene would be responsible for some regioirregular 2,1‐inserted propene units, which at high temperatures give rearrangement to 3,1 units.

     

Synthesis and characterization of cis‐polybutadiene‐block‐syn‐polystyrene copolymers with a cyclopentadienyl titanium trichloride/modified methylaluminoxane catalyst

This article reports a practical method for preparing cis‐polybutadiene‐block‐syn‐polystyrene (cis‐PB‐b‐syn‐PS) copolymers with long crystallizable syndiotactic polystyrene (syn‐PS) segments chemically bonded with high cis‐1,4‐polybutadiene segments through the addition of styrene (ST) to a cis‐specific 1,3‐butadiene (BD) living catalyst composed of cyclopentadienyl titanium trichloride (CpTiCl₃) and modified methylaluminoxane (MMAO). The incorporation of ST into the living polybutadiene (PB) precursor remarkably depended on the polymerization temperature. A low temperature (?20 °C) suppressed the rate of ST incorporation, but a high temperature (50 °C) tended to decompose the livingness of the active species and enhance the rate of the aspecific ST polymerization initiated by MMAO. Consequently, temperatures of 0–25 °C seemed to be best for this copolymerization system. Because of the absence of ST livingness, the final products contained not only the block copolymer but also the homopolymers. Attempts to isolate the block copolymer were carried out with common solvent fractionation techniques, but the results were not sufficient. Cross‐fractionation chromatography was, therefore, used for the isolation of the cis‐PB‐b‐syn‐PS copolymer. The presence of long syn‐PS segments was confirmed by the observation of a strong endothermic peak at 260 °C in the differential scanning calorimetry curve. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2698–2704, 2004     

Ethylene/1‐hexene copolymerization with tetramethyldisiloxane‐bridged bis(indenyl) metallocenes

Ethylene/1‐hexene copolymerizations with disiloxane‐bridged metallocenes, rac‐ and meso‐1,1,3,3‐tetramethyldisiloxanediyl‐bis(1‐indenyl)zirconium dichloride (rac‐ 1 , meso‐ 1 ) activated by modified methylaluminoxane were performed to investigate the influence of conformational dynamics on comonomer selectivity. Although ¹H NOESY (nuclear Overhauser and exchange spectroscopy) analysis indicated that the most stable conformation for the meso isomer in solution was that in which both indenes project over the metal coordination site, this isomer showed higher 1‐hexene selectivity in copolymerization (r_e = 140 ± 30, r_h = 0.024 ± 0.004) than the rac isomer with only one indene over the coordination site (r_e = 240 ± 20, r_h = 0.005 ± 0.001). The meso isomer showed high 1‐hexene selectivity, a high product of reactivity ratios (r_er_h = 3.3 ± 0.5) and produced copolymers that could be separated into fractions with different ethylene content suggesting that the active species exhibited multisite behavior and populated conformations with different comonomer selectivities during the copolymerization. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3323–3331, 2004     

cis‐1,4‐specific carbocationic polymerization and copolymerization of 1,3‐dienes initiated by (S,S)‐bis(oxazolinylphenyl)amine chromium complexes

Two new chiral (S,S)‐bis(oxazolinylphenyl)amine chromium dichloride complexes have been synthesized and structurally characterized. In combination with 2 equiv. of borate and an excess of AlR₃, such Cr complexes serve as effective cationic initiators in the stereoregular carbocationic polymerization of 1,3‐dienes such as isoprene (IP) and myrcene (MY), affording cyclized cis‐1,4‐PIPs/PMys (cis‐1,4‐selectivity up to 96%) with cyclic sequence contents ranging from 26% to 87%. Moreover, these Cr initiator systems also exhibit an unprecedented control over sequence distribution of comonomers in the carbocationic copolymerization of IP and MY, preparing novel copolymers with different microstructures from mainly cyclized cis‐1,4‐specific statistical copolymers to cyclic olefin copolymers. The nature of Cr complex, borate, AlR₃, temperature, molar ratio of comonomers has considerable effect on the (co)polymer's yield, stereoselectivity, cyclization, and comonomer sequence distribution. A plausible mechanism is suggested, which gives a new strategy for biomimetic synthesis of natural rubber. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 55, 1250–1259     

Cyclocopolymerization of 1,4‐pentadiene with ethene in the presence of group‐4 metallocenes

The behaviors of rac‐[CH₂(3‐tert‐butyl‐1‐indenyl)₂]ZrCl₂ ( 1 ) and Cp₂ZrCl₂ ( 2 ) activated by methylaluminoxane in ethene/1,4‐pentadiene copolymerization are compared. In the presence of 1 , inserted methylene‐1,3‐cyclobutane units, a large number of crosslinks, and a small number of methylene‐1,3‐cyclohexane units are obtained. Differently, a polyethene containing only 1,3‐cyclohexane rings is achieved with 2 as the catalytic precursor. Polymer microstructures are compared with those obtained with 1 and 2 in ethene/1,6‐heptadiene copolymerization, which leads only to polyethene containing cyclohexane rings. A tentative rationalization of the experimental data is reported. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5525–5532, 2006     

Ethylene/α‐olefin copolymerization with bis(β‐enaminoketonato) titanium complexes activated with modified methylaluminoxane

Copolymerizations of ethylene with α‐olefins (i.e., 1‐hexene, 1‐octene, allylbenzene, and 4‐phenyl‐1‐butene) using the bis(β‐enaminoketonato) titanium complexes [(Ph)NC(R₂)CHC(R₁)O]₂TiCl₂ ( 1a : R₁ = CF₃, R₂ = CH₃; 1b : R₁ = Ph, R₂ = CF₃; and 1c : R₁ = t‐Bu, R₂ = CF₃), activated with modified methylaluminoxane as a cocatalyst, have been investigated. The catalyst activity, comonomer incorporation, and molecular weight, and molecular weight distribution of the polymers produced can be controlled over a wide range by the variation of the catalyst structure, α‐olefin, and reaction parameters such as the comonomer feed concentration. The substituents R₁ and R₂ of the ligands affect considerably both the catalyst activity and comonomer incorporation. Precatalyst 1a exhibits high catalytic activity and produces high‐molecular‐weight copolymers with high α‐olefin insertion. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6323–6330, 2005     

Copolymerization of ethylene and cyclopentene with bis(β‐enaminoketonato) titanium complexes

The copolymerizations of ethylene and cyclopentene with bis(β‐enaminoketonato) titanium complexes {[(Ph)NC(R₂)CHC(R₁)O]₂TiCl₂; R₁ = CF₃ and R₂ = CH₃ for 1a , R₁ = Ph and R₂ = CF₃ for 1b ; and R₁ = t‐Bu and R₂ = CF₃ for 1c } activated with modified methylaluminoxane (MMAO) as a cocatalyst were investigated. High‐molecular‐weight copolymers with cis‐1,2‐cyclopentene units were obtained. The catalyst activity, cyclopentene incorporation, polymer molecular weight, and polydispersity could be controlled over a wide range through the variation of the catalyst structure and reaction parameters, such as the Al/Ti molar ratio, cyclopentene feed concentration, and polymerization reaction temperature. The complex 1b /MMAO catalyst system exhibited the characteristics of a quasi‐living ethylene polymerization and an ethylene–cyclopentene copolymerization and allowed the synthesis of polyethylene‐block‐poly(ethylene‐co‐cyclopentene) diblock copolymer. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1681–1689, 2005     

Chain microstructure of homogeneous ethylene‐1‐alkene copolymers and characteristics of single site catalysts using a direct 13C NMR peak method. Part III. Application to ethylene–propylene copolymers showing no inversion

All relevant ¹³C NMR signals of two series of seven homogeneous ethylene–propylene copolymers were used to fit the second‐order Markov reactivity ratios of the catalysts and the theoretical feeds. The copolymers cover a very broad range of comonomer incorporations, from about 10 to 93%, and show only primary (1,2) insertions. For both series, solutions are found with reliabilities >>99.5%. The reactivity ratios, r₁₁₂ = 2.54, r₁₂₁ = 0.12, r₂₁₂ = 2.05, and r₂₂₁ = 0.29 for the used Zirconocone and r₁₁₂ = 1.69, r₁₂₁ = 0.32, r₂₁₂ = 1.56, and r₂₂₁ = 0.51 for the hafnocene, provide direct information about the metallocenes, the kinetics, and the chain microstructure. With these results, the direct peak method demonstrates that the use of all relevant ¹³C NMR peaks enables accurate second‐order Markov modeling, revealing subtle differences between copolymers. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 747–755, 2006     

Insights into propylene/ω‐halo‐α‐alkenes copolymerization promoted by rac‐Et(Ind)2ZrCl2 and (pyridyl‐amido)hafnium catalysts

This article discussed the root causes of the interesting differences between rac‐Et(Ind)₂ZrCl₂ and dimethyl (pyridyl‐amido)hafnium in catalyzing the propylene/ω‐halo‐α‐alkene copolymerization. Confirmed by density functional theory (DFT) calculations, the larger spacial opening around the active center of rac‐Et(Ind)₂ZrCl₂ contributes to the coordination and insertion of the monomers, resulting in the higher catalytic activity, while the narrow spacial opening around the Hf center retards the chain transfer reaction, leading to the much higher molecular weights (M_ws) of the copolymers. The superior tolerability of Zr catalyst toward halogen groups might be attributed to that the dormant species generated from halogen coordination could be promptly reactivated. DFT calculations indicated the higher probability for the ω‐halo‐α‐alkene vinyl to coordinate with the Hf catalyst leading to the better ability to incorporate halogenated monomers. The high M_ws and the outstanding isotacticity achieved by the Hf catalyst determined the higher melting temperature values of the copolymers with a certain amount of halogen groups. In addition, the chain transfer schemes were employed to analyze why the presence of halogenated monomers greatly decreased the M_ws of the copolymers when rac‐Et(Ind)₂ZrCl₂ was used, while had no or little effect upon the M_ws in the copolymerization by the Hf catalyst. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3421–3428     

Synthesis and characterization of poly(L‐lactic acid)–poly(ε‐caprolactone) multiblock copolymers by melt polycondensation

An Erratum has been published for this article in J. Polym. Sci. Part A: Polym. Chem. (2004) 42(22) 5845 New multiblock copolymers derived from poly(L‐lactic acid) (PLLA) and poly(ε‐caprolactone) (PCL) were prepared with the coupling reaction between PLLA and PCL oligomers with ? NCO terminals. Fourier transform infrared (FTIR), ¹³C NMR, and differential scanning calorimetry (DSC) were used to characterize the copolymers and the results showed that PLLA and PCL were coupled by the reaction between ? NCO groups at the end of the PCL and ? OH (or ? COOH) groups at the end of the PLLA. DSC data indicated that the different compositions of PLLA and PCL had an influence on the thermal and crystallization properties including the glass‐transition temperature (T_g), melting temperature (T_M), crystallizing temperature (T_c), melting enthalpy (ΔH_m), crystallizing enthalpy (ΔH_c), and crystallinity. Gel permeation chromatography (GPC) was employed to study the effect of the composition of PLLA and PCL and reaction time on the molecular weight and the molecular weight distribution of the copolymers. The weight‐average molecular weight of PLLA–PCL multiblock copolymers was up to 180,000 at a composition of 60% PLLA and 40% PCL, whereas that of the homopolymer of PLLA was only 14,000. A polarized optical microscope was used to observe the crystalline morphology of copolymers; the results showed that all polymers exhibited a spherulitic morphology. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5045–5053, 2004     

Ni(II) and Pd(II) complexes bearing benzocyclohexane–ketoarylimine for copolymerization of norbornene with 5‐norbornene‐2‐carboxylic ester

A serial of late transition metal complexes, which bearing Benzocyclohexane–ketoarylimine ligand and named as Mt(benzocyclohexane–ketoarylimino)₂ {Mt(bchkai)₂: Mt=Ni or Pd; bchkai=C₁₀H₈(O)CN(Ar)CH₃; Ar=naphthyl or fluoryl}, have been synthesized and characterized. The molecular structures of the ligands and nickel complex have been confirmed by X‐ray single‐crystal analyses. The nickel complexes exhibited very high activity up to 2.7 × 10⁵ g_polymer/mol_Ni·h and palladium complexes showed high activity up to 2.3 × 10⁵ g_polymer/mol_Pd·h for norbornene (NB) homo‐polymerization with tris(pentafluorophenyl)borane as cocatalyst. The four complexes were effective for copolymerization of NB and 5‐norbornene‐2‐carboxylic acid methyl ester (NB‐COOCH₃) in relatively high activities (0.1–2.4 × 10⁵ g_polymer/mol_Mt·h) and produced the addition‐type copolymers with relatively high molecular weights (0.5 × 10⁵–1.2 × 10⁵ g/mol) as well as narrow molecular weight distributions (PDI < 2 for all polymers). Influences of the metals and comonomer feed content on the polymerization activity as well as on the incorporation rates (20.9–42.6%) were investigated. The achieved NB/NB‐COOCH₃ copolymers were confirmed to be noncrystalline, exhibited good thermal stability (T_d > 400°C) and showed good solubility in common organic solvents. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Hydrogenation of polystyrene‐b‐polybutadiene‐b‐polystyrene mediated by group (IV) metal metallocene complexes

Various group (IV) metal complexes, namely bis(cyclopentadienyl) titanium dichloride, bis(pentamethylcyclopentadienyl) titanium dichloride, cyclopentadienyl titanium trichloride, pentamethylcyclopentadienyl titanium trichloride, bis(cyclopentadienyl) zirconium dichloride, and bis(cyclopentadienyl) hafnium dichloride, were used as the catalysts for mediating styrene–butadiene–styrene hydrogenation. The catalytic efficiency of these catalysts was examined. The results show that catalyst activity strongly depends on the chemical structure of the metallocene complex. We also found that trialkylaluminum has a significant influence on the hydrogenation activity and thermal stability of metallocene catalysts. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2141–2149     

Vanadium(III) complexes containing phenoxy–imine–thiophene ligands: Synthesis,characterization and application to homo‐ and copolymerization of ethylene

A set of vanadium(III) complexes, namely {SNO}VCl₂(THF)₂ ( 2a , SNO = thiophene‐(N═CH)‐phenol; 2b , SNO = 5‐phenylthiophene‐(N═CH)‐phenol; 2c , SNO = 5‐phenylthiophene‐(N═CH)‐4‐tert ‐butylphenol; 2d , SNO = 5‐methylthiophene‐(N═CH)‐phenol; 2e , SNO = 5‐methylthiophene‐(N═CH)‐4‐tert ‐butylphenol; 2f , SNO = 5‐methylthiophene‐(N═CH)‐2‐methylphenol; 2g , SNO = 5‐methylthiophene‐(N═CH)‐4‐fluorophenol), were synthesized by reaction of VCl₃(THF)₃ with phenoxy–imine–thiophene proligands ( 1a – g ). All vanadium(III) complexes were characterized using elemental analysis and infrared and electron paramagnetic resonance spectroscopies. Upon activation with methylaluminoxane (MAO), vanadium precatalysts 2a – g proved active in the polymerization of ethylene (213.6–887.2 kg polyethylene (mol[V])⁻¹⋅h⁻¹), yielding high‐density polyethylenes with melting temperatures in the range 133–136 °C and crystallinities varying from 28 to 41%. The 2e/ MAO catalyst system was able to copolymerize ethylene with 1‐hexene affording poly(ethylene‐co ‐1‐hexene)s with melting temperatures varying from 126 to 102 °C and co‐monomer incorporation in the range 3.60–4.00%.     

Synthesis of polyesters with pendant oxetane groups by the chemoselective alternating copolymerization of 3‐ethyl‐3‐(glycidyloxymethyl)oxetane with carboxylic anhydride and its photochemical reaction

The synthesis of polyesters with pendant oxetane groups by the chemoselective alternating copolymerization of 3‐ethyl‐3‐(glycidyloxymethyl)oxetane (EGMO) with carboxylic anhydride and the photochemical reaction of the resulting polymer was examined. The alternating copolymerization of EGMO with phthalic anhydride proceeded chemoselectively with quaternary onium salts under appropriate reaction conditions, and the corresponding soluble polymers with pendant oxetane groups with number‐average molecular weights of 4700–7200 were obtained in 72–87% yields. Furthermore, the photochemical reaction of the resulting polymers was examined with certain photoacid generators in the film state upon UV irradiation, and it was found that the photocrosslinking reaction of the pendant oxetane groups proceeded smoothly to give the insoluble polymers. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1952–1961, 2003