Miscibility and crystallization behavior of poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) and methoxy poly(ethylene glycol) blends

Poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) (PHB‐HHx) and methoxy poly(ethylene glycol) (MPEG) blends were prepared using melt blending. The single glass transition temperature, T_g, between the T_gs of the two components and the negative χ value indicated that PHB‐HHx and MPEG formed miscible blends over the range of compositions studied. The Gordon–Taylor equation proved that there was an interaction between PHB‐HHx and MPEG in their blends. FTIR supported the presence of hydrogen bonding between the hydroxyl group of MPEG and the carbonyl group of PHB‐HHx. The spherulitic morphology and isothermal crystallization behavior of the miscible PHB‐HHx/MPEG blends were investigated at two crystallization temperatures (70 and 40 °C). At 70 °C, melting MPEG acted as a noncrystalline diluent that reduced the crystallization rate of the blends, while insoluble MPEG particles acted as a nucleating agent at 40 °C, enhancing the crystallization rate of the blends. However, no interspherulitic phase separation was observed at the two crystallization temperatures. The constant value of the Avrami exponent demonstrated that MPEG did not affect the three‐dimensional spherulitic growth mechanism of PHB‐HHx crystals in the blends, although the MPEG phase, such as the melting state or insoluble state, influenced the crystallization rate of the blends. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2852–2863, 2006     

Evaluation of the interaction parameter for poly(ε‐caprolactone)/poly(styrene‐co‐acrylonitrile) blends

In this article, the miscibility of poly(ε‐caprolactone) (PCL) with poly(styrene‐co‐acrylonitrile) (SAN) containing 25 wt % of acrylonitrile is studied from both a qualitative and a quantitative point of view. The evidences coming from thermal analysis (differential scanning calorimetry) demonstrate that PCL and SAN are miscible in the whole range of composition. The Flory interaction parameter χ_1,2 was calculated by the Patterson approximation and the melting point depression of the crystalline phase in the blends; in both cases, negative values of χ_1,2 were found, confirming that the system is miscible. The interaction parameter evaluated within the framework of the mean field theory demonstrates that the miscibility of PCL/SAN blends is due to the repulsive interaction between the styrene and acrylonitrile segments in SAN. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Morphology and crystallization behavior of poly(l‐lactide)/poly(butylene oxalate) blends

The isothermal crystallization of poly(l ‐lactide) (PLLA) in blends with poly(butylene oxalate) (PBOX) is investigated by time‐resolved small‐angle X‐ray scattering, differential scanning calorimetry, and optical microscopy. We focus on the temperatures at which only PLLA crystallizes while PBOX is amorphous. It is obtained that the addition of PBOX causes a reduction of the melting temperature of PLLA. The lamellar thickness of PLLA crystals decreases whereas the amorphous layer thickness increases with blend composition, suggesting the occurrence of the interlamellar incorporation upon the addition of PBOX. The crystal growth rate and morphology of PLLA/PBOX blends are analyzed by polarized optical microscopy. The spherulite growth rate of PLLA is found to increase with the addition of PBOX. Analysis of the isothermal crystallization in terms of the Lauritzen and Hoffman equation give the reduction of the fold surface free energy upon the addition of PBOX in PLLA, indicating that the mobility of the PLLA chains is significantly improved due to the presence of PBOX. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 192–202     

Interplay of fractionated crystallization and morphology in polypropylene/poly(ϵ‐caprolactone) blends

The thermal behavior of melt‐mixed polypropylene (PP)/poly(?‐caprolactone) (PCL) blends was investigated with differential scanning calorimetry, and it was quantitatively related to the morphology observed through scanning electron microscopy. The PP/PCL blends were immiscible in the whole composition range; however, some interesting phenomena were found. Blends with low PP contents crystallized in a fractionated fashion. By applying a self‐nucleation procedure, we demonstrated that this occurred because of a lack of highly active heterogeneities within the confined PP domains. On the other hand, PP acted as a nucleating agent for PCL, and when the PP content was reduced, the higher surface/volume ratio increased its nucleating activity. The nucleating effect was improved when the PP was self‐nucleated because of the better nucleating effect of PP annealed crystals. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1365–1379, 2007     

Influence of hyperbranched against linear architecture on crystallization behavior of poly(ε‐caprolactone)s in binary blends with poly(vinyl chloride)

Nonisothermal and isothermal crystallization behaviors of the hyperbranched poly(ε‐caprolactone) (HPCL)/poly(vinyl chloride) (PVC) and linear poly(ε‐caprolactone) (LPCL)/(PVC) blends were characterized with various blend composition such as 100/0, 95/5, 90/10, and 80/20, respectively. HPCL was synthesized through polycondensation of AB₂ macromonomer while LPCL and PVC were commercially purchased. The architectural characterization performed on ¹H NMR spectra revealed that HPCL consisted of about 3 AB₂ units and the linear segments consisted of 25 ε‐CL units. Through the nonisothermal crystallization analyses by modified Avrami approach with DSC crystallization exotherms, it was found that the crystallization rate was retarded by the increase in the noncrystallizable component (PVC) in the blends. This is in good agreement with the results of the isothermal crystallization analyses where time resolved small angle light scattering (SALS) and polarized optical microscopy (POM) were used. The effect of molecular architectural difference between HPCL and LPCL on the crystallization of their binary blends with PVC was elucidated by comparing the crystallization kinetic parameters. Both the nonisothermal and isothermal crystallization analyses showed that the crystallization rates of HPCL/PVC blends was faster than LPCL/PVC blends at given blend compositions. The faster crystallization of the HPCL/PVC blends is ascribed to the two specific architectural characteristics of HPCL; the branched structure and the incorporated long linear segments. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 577–589, 2007     

Melting behavior,miscibility, and hydrogen-bonded interactions of poly(ε-caprolactone)/poly(4-hydroxystyrene-co-methoxystyrene) blends

The miscibility of poly(4-hydroxystyrene-co-methoxystyrene) (HSMS) and poly(ε-caprolactone) (PCL) was investigated by differential scanning calorimetry and Fourier transform infrared spectroscopy (FTIR). HSMS/PCL blends were found to be miscible in the whole composition range by detecting only a glass transition temperature (T_g), for each composition, which could be closely described by the Fox rule. The crystallinity of PCL in the blends was dependent on the T_g of the amorphous phase. The greater the HSMS content in the blends, the lower the crystallinity. The polymer–polymer interaction parameter, χ₃₂, was calculated from melting point depression of PCL using the Nishi-Wang equation. The negative value of χ₃₂ obtained for HSMS/PCL blends has been compared with the value of χ₃₂ for poly(4-hydroxystyrene) (P4HS)/PCL blends. The specific nature, quantitative analysis, and average strength of the intermolecular interactions in HSMS/PCL and P4HS/PCL blends have been determined at room temperature and in the molten state by means of Fourier transform infrared spectroscopy (FTIR) measurements. The FTIR results have been in good correlation with the thermal behavior of the blends. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36 : 95–104, 1998     

Mechanical,thermal and morphological properties of poly(ε‐caprolactone)/zein blends

Blends of poly(ε‐caprolactone) (PCL) with zein (PCL/zein) in different proportions (100/0, 75/25, 50/50, 25/75 and 0/100 wt% containing 5 wt% glycerol) were compared based on their mechanical properties (tensile strength, elongation at break, and Young's modulus), and on their thermal properties, the latter determined by thermogravimetric analysis (TGA) and dynamic mechanical thermal analysis (DMTA). The morphology of the materials was studied by scanning electron microscopy (SEM). Blends of PCL/zein showed reduced tensile strength and elongation at break, but increased Young's modulus compared to the pure polymers, in agreement with the DMTA and SEM results. These findings indicated that PCL and zein were incompatible. TGA showed that the thermal stability was enhanced by the addition of zein to PCL, whereas SEM showed a poor interfacial interaction between the polymers. Copyright © 2004 John Wiley & Sons, Ltd.     

Stimuli‐responsive polyurethane bionanocomposites of poly(ethylene glycol)/poly(ε‐caprolactone) and [poly(ε‐caprolactone)‐grafted‐] cellulose nanocrystals

In this study, in situ polyurethane (PU) bionanocomposites of poly(ethylene glycol) (PEG)/poly(ε‐caprolactone) (PCL) polyols, bare cellulose nanocrystals (CNCs) and PCL‐grafted CNCs (G‐CNC) were synthesized with different contents of CNCs as cross‐linking agent to control the extent of phase separation. The effect of confining the chains between CNCs through urethane linkages and presence of PCL grafts on phase and crystallization behavior was evaluated. Crystallization and chemical networking were controlled to tune the shape fixity (SF) and recovery (SR) of the specimens, resulting in a SF of 100% for linear and PU nanocomposites of G‐CNC (0.5% and 1%) samples. The PU nanocomposite of G‐CNC (0.5%) was selected as the optimum sample with the highest SR of 100%. The effect of surface hydrophobicity on cellular behavior of Human Foreskin Fibroblast (as a normal cell) and HepG2 (as a cancerous cell) cells was evaluated. Cell adhesion analysis of the prepared samples indicated two different behaviors possibly due to the difference in the epigenetic nature of the cells and cellular integrin‐ based bonds showing a great potential for a variety of tissue engineering applications.     

Rheological and thermal study of delayed crystallization in poly(butylene terephthalate)/ethylene‐co‐ethyl acrylate blends

The effects of the composition and resulting morphology on the crystallization and rheology of blends containing poly(butylene terephthalate) (PBT) and an ethylene‐co‐ethyl acrylate (EEA) copolymer, two immiscible polymers, were studied over the entire range of volume fractions. Differential scanning calorimetry (DSC) thermograms recorded during cooling showed important differences, mainly in terms of the PBT crystallization temperatures, depending on the blend composition. In addition to the classical crystallization peaks of PBT and EEA, a third crystallization peak appeared for blends containing less than 60% PBT. This peak was attributed to a delayed crystallization of PBT. This phenomenon was examined in terms of homogeneous crystallization. Linear viscoelastic measurements allowed the delayed crystallization behavior in these polymer blends to be displayed. Indeed, the variation of the storage modulus with the temperature showed increasing steps during cooling. These sudden increases appeared at temperatures very close to those at which the crystallization peaks were observed in the DSC experiments. This behavior was verified for different blend compositions. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 714–721, 2004     

Stability of the co‐continuous morphology during melt mixing for poly(ε‐caprolactone)/polystyrene blends

Over the last 10 years, research into co‐continuous polymer blends has been intense. Despite these efforts, there are very few detailed studies on the stability of this complex morphology. In this work, blends of poly(ε‐caprolactone) and polystyrene were melt‐mixed in an internal mixer for time intervals of 0.5–120 min at set temperatures of 140 and 170 °C, and the effect of the mixing time on the co‐continuous morphology was studied. This blend system was chosen because each component could be selectively dissolved and this allowed for a complete study of the co‐continuous region. The phase continuity was measured with a solvent‐extraction gravimetric technique, and the concentration range for co‐continuity was determined. The phase size and phase size distribution were obtained with the mercury intrusion porosimetry technique. The results indicate that the co‐continuous morphology forms very early in the mixing process and achieves a stable morphology within the first 5 min of mixing for virtually all the co‐continuous compositions. For all cases studied, the co‐continuous morphology remains unchanged over mixing times as long as 1–2 h. These results support the notion of a stable steady‐state formation of co‐continuous morphologies during melt mixing similar to that observed for matrix/dispersed phase type blends. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 864–872, 2007     

Crystallization behavior of poly(ε‐caprolactone)/multiwalled carbon nanotube composites

Differential scanning calorimetry (DSC), polarized optical microscopy, and X‐ray diffraction methods were used to investigate the isothermal crystallization behavior and crystalline structure of poly(?‐caprolactone) (PCL)/multiwalled carbon nanotube (MWNT) composites. PCL/MWNT composites were prepared via the mixing of a PCL polymer solution with carboxylic groups containing multiwalled carbon nanotubes (c‐MWNTs). Both Raman and Fourier transform infrared spectra indicated that carboxylic acid groups formed at both ends and on the sidewalls of the MWNTs. A transmission electron microscopy micrograph showed that c‐MWNTs were well separated and uniformly distributed in the PCL matrix. DSC isothermal results revealed that introducing c‐MWNTs into the PCL structure caused strongly heterogeneous nucleation induced by a change in the crystal growth process. The activation energy of PCL drastically decreased with the presence of 0.25 wt % c‐MWNT in PCL/c‐MWNT composites and then increased with increasing MWNT content. The result indicated that the addition of c‐MWNT to PCL induced heterogeneous nucleation (lower total activation energy) at a lower c‐MWNT content and then reduced the transportation ability of polymer chains during crystallization processes at a higher MWNT content (higher total activation energy). A correlation between the crystallization kinetics, melting behavior, and crystalline structure of PCL/c‐MWNT composites was also discussed. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 598–606, 2006     

Specific interactions and phase behavior of ternary poly(2‐vinylpyridine)/poly(N‐vinyl‐2‐pyrrolidone)/bisphenol A blends

Hydrogen‐bonding interactions between bisphenol A (BPA) and two proton‐accepting polymers, poly(2‐vinylpyridine) (P2VPy) and poly(N‐vinyl‐2‐pyrrolidone) (PVP), were examined by Fourier transform infrared (FTIR) spectroscopy and differential scanning calorimetry (DSC). The Flory–Huggins interaction‐energy densities of BPA/P2VPy and BPA/PVP blends were determined by the melting point depression method. The interaction parameters for both BPA/P2VPy and BPA/PVP blend systems were negative, demonstrating the miscibility of BPA with P2VPy as well as PVP. The miscibility of ternary BPA/P2VPy/PVP blends was examined by DSC, optical observation, and solid‐state nuclear magnetic resonance spectroscopy. The experimental phase behavior of the ternary blend system agreed with the spinodal phase‐separation boundary calculated using the determined interaction‐energy densities. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1125–1134, 2002     

Oriented lamellar structures in uniaxially drawn films of poly(vinylidene fluoride) and poly(3‐hydroxybutyrate) blends studied by small‐angle X‐ray scattering measurements

The lamellar structures in uniaxially drawn films of miscible crystalline/crystalline polymer blends of poly(vinylidene fluoride) (PVDF) and poly(3‐hydroxybutyrate) (PHB) were investigated by static and time‐resolved measurements of small‐angle X‐ray scattering (SAXS). Intense SAXS in the low angle range of the meridian was interpreted as originating from the interlamellar inclusion structure, in which the PHB chains were included between the lamellae of PVDF. The interlamellar inclusion was induced for the uniaxially drawn films of PVDF/PHB = 30/70 blend with a draw ratio (DR) of 2.8–4.5, whereas the lamellae of the PVDF and PHB components were mutually excluded from each other forming their own lamellar stacks (interlamellar exclusion) in the blend with a higher DR (5.0–5.7). When the highly drawn film with the interlamellar exclusion structure was heat treated at 154–165 °C, the interlamellar inclusion structure was partially induced by the heat treatment. The time‐resolved SAXS measurements indicated that the interlamellar inclusion structure was developed by melting and recrystallization of PVDF during the heat treatment. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 381–392, 2009     

Self‐decelerated crystallization in blends of polyhydroxyether of bisphenol A and poly(ethylene oxide) upon isothermal crystallization

The growth of spherulites of poly(ethylene oxide) in blends with poly(hydroxyether of bisphenol A) was investigated. In a very narrow range of crystallization temperatures, the spherulite growth deviates from the usual constant growth rate regime in a systematic manner in which the growth rate decreases with time. This is explained by local and overall changes in the composition with the proceeding crystallization that are due to the competition between the crystallization and diffusional chain displacement rates, respectively. These kinetic phenomena and processes can quantitatively be described by a suitable analysis of the experimental findings. Deceleration is predominantly caused by a slowing of the chain motion by the glass‐transition temperature being approached (i.e., vitrification) and, to a lesser extent, by dilution. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1250–1257, 2000     

Non-isothermal crystallization kinetics of poly(trimethylene terephthalate)/poly(ethylene 2,6-naphthalate) blends

The glass-transition temperature and non-isothermal crystallization of poly(trimethylene terephthalate)/poly(ethylene 2,6-naphthalate) (PTT/PEN) blends were investigated by using differential scanning calorimeter (DSC). The results suggested that the binary blends showed different crystallization and melting behaviors due to their different component of PTT and PEN. All of the samples exhibited a single glass-transition temperature, indicating that the component PTT and PEN were miscible in amorphous phase. The value of T_g predicted well by Gordon-Taylor equation decreased gradually with increasing of PTT content. The commonly used Avrami equation modified by Jeziorny, Ozawa theory and the method developed by Mo were used, respectively, to fit the primary stage of non-isothermal crystallization. The kinetic parameters suggested that the PTT content improved the crystallization of PEN in the binary blend. The crystallization growth dimension, crystallization rate and the degree of crystallinity of the blends were increased with the increasing content of PTT. The effective activation energy calculated by the advanced iso-conversional method developed by Vyazovkin also concluded that the value of E_a depended not only on the system but also on temperature, that is, the binary blend with more PTT component had higher crystallization ability and the crystallization ability is increased with increasing temperature. The kinetic parameters U^* and K_g were also determined, respectively, by the Hoffman-Lauritzen theory.     

Alkaline-solution-induced crystallization in poly(butylene terephthalate)

Subtle crystalline structure changes of poly(butylene terephthalate) (PBT) specimens treated with an alkali solution at room temperature were investigated with the grazing incidence X-ray diffraction (GIXRD) analysis method. A new phenomenon was found: the aqueous alkali solution induced the crystallization of the PBT polymer. Under the GIXRD analysis condition of an incidence angle of 1°, the penetration depth of the X-ray in PBT was less than 80 μm, and this agreed well with the rough theoretical estimation. The alkali solution adopted in this study was an aqueous sodium hydroxide solution, which had a concentration of 2.5 N. Dissolved quantities of the surface layers during the alkaline treatment were found to be small. No appreciable intrinsic viscosity change due to the alkaline treatment was detected. Possible factors that might contribute to the crystallization, such as water absorption and a chemical reagent effect, were examined, and a plausible explanation for the phenomenon was developed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1938–1948, 2004     

Phase behavior,crystallization, and morphology in thermosetting blends of a biodegradable poly(ethylene glycol)‐type epoxy resin and poly(ϵ‐caprolactone)

Thermosetting blends of a biodegradable poly(ethylene glycol)‐type epoxy resin (PEG‐ER) and poly(?‐caprolactone) (PCL) were prepared via an in situ curing reaction of poly(ethylene glycol) diglycidyl ether (PEGDGE) and maleic anhydride (MAH) in the presence of PCL. The miscibility, phase behavior, crystallization, and morphology of these blends were investigated. The uncured PCL/PEGDGE blends were miscible, mainly because of the entropic contribution, as the molecular weight of PEGDGE was very low. The crystallization and melting behavior of both PCL and the poly(ethylene glycol) (PEG) segment of PEGDGE were less affected in the uncured PCL/PEGDGE blends because of the very close glass‐transition temperatures of PCL and PEGDGE. However, the cured PCL/PEG‐ER blends were immiscible and exhibited two separate glass transitions, as revealed by differential scanning calorimetry and dynamic mechanical analysis. There existed two phases in the cured PCL/PEG‐ER blends, that is, a PCL‐rich phase and a PEG‐ER crosslinked phase composed of an MAH‐cured PEGDGE network. The crystallization of PCL was slightly enhanced in the cured blends because of the phase‐separated nature; meanwhile, the PEG segment was highly restricted in the crosslinked network and was noncrystallizable in the cured blends. The phase structure and morphology of the cured PCL/PEG‐ER blends were examined with scanning electron microscopy; a variety of phase morphologies were observed that depended on the blend composition. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2833–2843, 2004     

Nonisothermal crystallization kinetics of poly(ε‐caprolactone) blocks in double crystalline triblock copolymers containing poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) and poly(ε‐caprolactone) units

The poly(3‐hydroxbutyrate‐co‐3‐hydroxyvalerate)/poly(ε‐caprolactone) block copolymers (PHCLs) with three different weight ratios of PCL blocks (38%, named PHCL‐38; 53%, named PHCL‐53; and 60%, named PHCL‐60) were synthesized by using PHBV with two hydroxyl end groups to initiate ring‐opening polymerization of ε‐caprolactone. During DSC cooling process, melt crystallization of PHCL‐53 at relatively high cooling rates (9, 12, and 15 °C min^?1) and PHCL‐60 at all the selected cooling rates corresponded to PCL blocks so that PHCL‐53 and PHCL‐60 were used to study the nonisothermal crystallization behaviors of PCL blocks. The kinetics of PCL blocks in PHCL‐53 and PHCL‐60 under nonisothermal crystallization conditions were analyzed by Mo equation. Mo equation was successful in describing the nonisothermal crystallization kinetics of PCL blocks in PHCLs. Crystallization activation energy were estimated using Kissinger's method. The results of kinetic parameters showed that both blocks crystallized more difficultly than corresponding homopolymers. With the increase of PCL content, the crystallization rate of PCL block increased gradually. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Intramolecular interactions in poly(styrene-co-acrylonitrile)/poly(ε-caprolactone) blends

Specific interactions in blends of poly(ε-caprolactone) (PCL) and poly(styrene-co-acry-lonitrile) (SAN) were studied as a function of copolymer composition and blend ratio by using Fourier-transform infrared spectroscopy (FTIR). It was shown that miscibility occurred within a certain range of copolymer compositions because the presence of PCL reduced the thermodynamically unfavorable repulsion between styrene and acrylonitrile segments in the random copolymer. This effect was observed in terms of a shift to higher frequencies in the 700 cm^-1 γ-CH out-of-plane deformation vibration absorption of styrene and in the approximately 2236 cm^?1 C?N stretching frequency band in acrylonitrile segments. Specific intermolecular interactions between SAN and PCL were not observed in this study. © 1993 John Wiley & Sons, Inc.     

Miscibility,crystallization kinetics,and morphology of poly(β‐hydroxybutyrate) and poly(methyl acrylate) blends

The miscibility, spherulite growth kinetics, and morphology of binary blends of poly(β‐hydroxybutyrate) (PHB) and poly(methyl acrylate) (PMA) were studied with differential scanning calorimetry, optical microscopy, and small‐angle X‐ray scattering (SAXS). As the PMA content increases in the blends, the glass‐transition temperature and cold‐crystallization temperature increase, but the melting point decreases. The interaction parameter between PHB and PMA, obtained from an analysis of the equilibrium‐melting‐point depression, is −0.074. The presence of an amorphous PMA component results in a reduction in the rate of spherulite growth of PHB. The radial growth rates of spherulites were analyzed with the Lauritzen–Hoffman model. The spherulites of PHB were volume‐filled, indicating the inclusion of PMA within the spherulites. The long period obtained from SAXS increases with increased PMA content, implying that the amorphous PMA is entrapped in the interlamellar region of PHB during the crystallization process of PHB. All the results presented show that PHB and PMA are miscible in the melt. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1860–1867, 2000