一种新型的极弱酸碱分析方法——固定pH滴定法

固定pH滴定法是一种新型的酸碱滴定方法。它的理论基础是弱酸弱碱在水溶液中各种存在形式的分布系数与溶液pH的关系。滴定时不需要确定等当点,也不需要标定滴定剂浓度,可用单标准比较法、标准曲线法或线性回归法对试样定量分析。用本法测定苯酚和甘氨酸,回收率在99.4～101%)。     

Tracer-monitored flow titrations

The feasibility of implementing tracer-monitored titrations in a flow system is demonstrated. A dye tracer is used to estimate the instant sample and titrant volumetric fractions without the need for volume, mass or peak width measurements. The approach was applied to spectrophotometric flow titrations involving variations of sample and titrant flow-rates (i.e. triangle programmed technique) or concentration gradients established along the sample zone (i.e. flow injection system). Both strategies required simultaneous monitoring of two absorbing species, namely the titration indicator and the dye tracer. Mixing conditions were improved by placing a chamber with mechanical stirring in the analytical path aiming at to minimize diffusional effects. Unlike most of flow-based titrations, the innovation is considered as a true titration, as it does not require a calibration curve thus complying with IUPAC definition. As an application, acidity evaluation in vinegars involving titration with sodium hydroxide was selected. Phenolphthalein and brilliant blue FCF were used as indicator and dye tracer, respectively. Effects of sample volume, titrand/titrant concentrations and flow rates were investigated aiming at improved accuracy and precision. Results were reliable and in agreement with those obtained by a reference titration procedure.     

Simple and cost-effective determination of ciprofloxacin hydrochloride by electrical micro-titration

By employing an electrical micro-titration system, in which a capacitively coupled contactless conductivity detector(C4D) was used to monitor the reaction process in real time, herein a novel method for determining ciprofloxacin hydrochloride(CIPHCl) was developed for the first time. Mode 1: Standard CIPHCl solutions at different concentrations were loaded into reaction cells, respectively, and were titrated with standard Ag+. Upon the titration, the formation of a precipitate alters the number of ions in the solution, raising the change of conductivity, which was monitored by a special C~4 D to construct a titration curve. The endpoint of the titration was located from the peak of the curve. Between the elapsed time and the initial concentration of titrand, a linear relationship was established over the range of2.0–8.0 mmol/L. Mode 2: Standard Fe~(3+) took the place of Ag~+, and was used as titrant to recognize ciprofloxacin contributed to the formation of complexation, which also resulting a change of solution conductivity. Under optimized conditions, a working range of 1.0–5.0 mmol/L CIPHCl was found. Because the reaction solutions were isolated from the working electrodes, this pioneer work shows significant simplicity and cost-effectiveness, by eliminating the requirements for detector exchange/renewal between different measurements, and by involving no auxiliary chemicals. Both of the two approaches were applied successfully to determine CIPHCl in tablet samples. And the results were in good agreement with those obtained by reference method.     

Gran电位滴定法测定乳酸环丙沙星

介绍了乳酸环丙沙星测定的Gran电位滴定法。采用Gran线性函数进行电位滴定,经图解外推或线性回归处理求出计量点,可直接用于测定乳酸环丙沙星原料药的含量。该法用于多批原料药的测定,结果与药典法基本一致。     

Novel approaches to analysis by flow injection gradient titration

Two novel procedures for flow injection gradient titration with the use of a single stock standard solution are proposed. In the multi-point single-line (MP-SL) method the calibration graph is constructed on the basis of a set of standard solutions, which are generated in a standard reservoir and subsequently injected into the titrant. According to the single-point multi-line (SP-ML) procedure the standard solution and a sample are injected into the titrant stream from four loops of different capacities, hence four calibration graphs are able to be constructed and the analytical result is calculated on the basis of a generalized slope of these graphs. Both approaches have been tested on the example of spectrophotometric acid–base titration of hydrochloric and acetic acids with using bromothymol blue and phenolphthalein as indicators, respectively, and sodium hydroxide as a titrant. Under optimized experimental conditions the analytical results of precision less than 1.8 and 2.5% (RSD) and of accuracy less than 3.0 and 5.4% (relative error (RE)) were obtained for MP-SL and SP-ML procedures, respectively, in ranges of 0.0031–0.0631 mol L⁻¹ for samples of hydrochloric acid and of 0.1680–1.7600 mol L⁻¹ for samples of acetic acid. The feasibility of both methods was illustrated by applying them to the total acidity determination in vinegar samples with precision lower than 0.5 and 2.9% (RSD) for MP-SL and SP-ML procedures, respectively.     

Potentiometric flow titration of iron(II) and chromium(VI) based on flow rate ratio of a titrant to a sample

A new potentiometric flow titration has been proposed based on the relationship of the flow rates between titrant and sample solutions. A sample solution is pumped at a constant flow rate. The flow rate of the titrant solution is gradually increased at regular time intervals and a flow rate for the titrant solution in the vicinity of the equivalence point is obtained. The concentration of the sample is calculated by C(S) (mol l(-1))=(R(T) (ml min(-1))xC(T) (mol l(-1)))/R(S) (ml min(-1)), where C(S), C(T), R(S), and R(T) denote the unknown sample concentration, titrant concentration in the reservoir, the flow rate of the sample solution which is a constant rate, and the flow rate of the titrant solution at an inflection point, respectively. The potentiometric flow titration of iron(II) with cerium(IV) and of chromium(VI) with iron(II) has been presented. The titration time of the proposed method is about 10 min per sample. An R.S.D. of the method is 0.77% for seven determinations of 1x10(-3) mol l(-1) iron(II). Similarly, the flow titration of chromium(VI) with iron(II) is carried out over the range 1x10(-4)-1x10(-3) mol l(-1) chromium(VI) and is successfully applied to the determination of chromium in high carbon ferrochromium.     

Determination of sulfate ion by potentiometric back-titration using sodium tetrakis (4-fluorophenyl) borate as a titrant and a titrant-sensitive electrode

A potentiometric back-titration method for the determination of sulfate ions using a plasticized poly(vinyl chloride) membrane electrode sensitive to a titrant is described. The method is based on ion association between the excess of 2-aminoperimidinium added to the sulfate ion in the sample and sodium tetrakis (4-fluorophenyl) borate (FPB) in the titrant. The titration end-point was detected as a sharp potential change due to an increase in the concentration of the free FPB at the equivalence point. The end-point was detected even in the presence of a 20-fold excess of common cations and anions relative to the concentration of the sulfate ion within approximately 2% of titration error. A linear relationship between the concentration of the sulfate ion and the end-point volume of the titrant exists in the sulfate ion concentration range from 2x10(-4) to 3x10(-3) mol l(-1) using 10(-2) mol l(-1) FPB solutions as the titrant. The present method could be applied to determine sulfate ions in sea water.     

Design of software for thermal titrations

A set of computer programs has been written in FORTRAN and in BASIC to allow automation of data acquisition from a TRONAC titration calorimeter and calculation of the concentration of titrant or titrand in an acid-base reaction; the heat capacity of a solution and enthalpies of reaction may also be calculated. The enthalpy change of a reaction and equilibrium constant can also be determined under certain conditions.     

Coupled chemical processes at clay/electrolyte interface: a batch titration study of Na-montmorillonites

The present work addresses the protolytic charge of montmorillonite, which occurs on the broken-bond sites at the particle edges. The purpose is to overcome the general difficulty arising in potentiometric titration due to coupled side reactions, which severely impede the titrant budget (partial dissolution of the clay and of secondary phases, hydrolysis and readsorption of dissolved species, cation exchange). Batch potentiometric titrations were carried out on the montmorillonite fractions extracted from two bentonites (MX80 and SWy2) to quantify their protolytic charge. The effects of equilibration time (24 h and 7 days), pH from 4 to 10, and ionic strength (0.1 and 0.01 mol L(-1)) were extensively studied for the MX80 sample. Quantification of dissolution was achieved by analysis of the equilibrium solutions for dissolved species and by La(3+) exchange of the readsorbed species. The results clearly show that secondary phases such as iron- or silica-rich minerals contribute to the dissolved species, according to the nature of the raw bentonite. Furthermore, readsorption affects significant amounts of dissolved species. The overconsumption of proton/hydroxide due to dissolution, readsorption, and hydrolysis of dissolved species was evaluated using a self-consistent thermodynamic calculation. The ability of such calculation to correct the raw titration curves in order to extract the titrable surface charge of montmorillonite was evaluated by comparison with the continuous titration procedure. Especially in the alkaline domain, correcting the raw batch titration curves for the measured side reactions failed to reproduce the continuous titration curves. These observations demonstrate the limitations of the batch titration method and the superiority of fast, continuous methods for quantifying the dissociable surface charge of clays.     

络合体系中的相对滴定法及其应用于铝的测定

本文提出了络合体系中的相对滴定分析法，它以滴定到一定的状态时，滴定剂体积与被测物的基之间的线性关系为定量基础，用仪器分析的定量方法进行定量，适应于所有类型的络合体系，即使对滴定突跃很小或根本无突跃的体系也同样适用。用氟离子滴定铝离子的实验结果表明本方法的精密度很高。一般相对误差小于0．1％。即使对于铝离子的量小到10-7mol／L时，在最佳实验条件下的相对误差也不大于0．2％。该方法既具有滴定分析法的高精密度，又具有仪器分析法可以测量微量物质的优点，并且设备和方法简单。     

Flow injection titration basing on the merging-zone technique

The proposed approach relies on titration of a sample that is gradually diluted in strictly controlled way in the flow injection system developed. On each step of sample dilution equal volumes of the sample and titrant solutions are simultaneously injected into two carrier streams and the zones are merged with each other. Then, they are mixed completely in the mixing chamber, merged with a stream of indicator and directed to a detector. It has been revealed that the method provides the results with accuracy better than ±3.3% (RE) and with mean repeatability lower than 1.0% (RSD). When the analyte concentration in a sample is too low to be determined directly, the procedure of titration with standard addition is exploited. The proposed approach has been successfully applied to the determination of total acidity in vinegars and magnesium and calcium in pharmaceutical products. The results obtained were comparable with those provided by the reference methods. The proposed procedure is characterized by low consumption of sample (usually less than 2 mL), titrant (about 3 mL) and indicator (about 0.6 mL). Average time of a single analysis is similar to time of traditional batch analysis.     

Sequential determination of uranium (IV), free acidity and hydrazine in a single aliquot

A simple analytical procedure for the sequential determination of uranium (IV), free acidity and hydrazine in presence of hydrolysable ions is developed and described. In this method, first, uranium (IV) is determined using fiber optic aided spectrophotometry then same solution is used for determination of free acidity and hydrazine. Free acid is titrated with standard sodium carbonate solution after uranium (IV) is masked with EDTA. Once the end point for the free acid is determined at pH 3.0, an aliquot of formaldehyde is added to liberate the acid equivalent to hydrazine which is then titrated with the same standard sodium carbonate solution using an automatic titration system. The described method is simple, accurate and reproducible. The overall recovery of uranium (IV), nitric acid and hydrazine is 98% with 3% relative standard deviation respectively. The major advantage of the method is that it uses sodium carbonate a primary standard as titrant and generation of corrosive analytical wastes containing oxalate or sulphate is avoided. Valuable metals like uranium and plutonium can easily be recovered from analytical waste before final disposal.     

Amperometrically indicated "pseudotitrations"--I. Complexometric determination of chromium(III)

In the pseudotitration no reaction takes place between titrand and titrant in the bulk of the solution. An amperometric indicating system, which generates a small amount of redox catalyst in the vicinity of the electrode, does enable an end-point to be found. Bulk concentrations and diffusion constants are the controlling parameters. This method allows to utilize slow, thermodynamically favourable reactions for titrating purposes. The principle is demonstrated by the direct titration of chromium(III) with EDTA at room temperature.     

Oxidability Determination in Waste Waters Using an Automatic Titrator Based on a Multicommutated Unsegmented Flow System

Abstract

The automatic titrator based on a multicommutated unsegmented flow system was applied to redox titrations and used for oxidability determination in waters analysis. This automatic titrator allows the attainment of complete titration curves, being the determination of titrand concentration performed without requiring any prior calibration. After sample treatment (oxidation step), the oxidability determination in waste water samples was accomplished by the automatic flow titrator (titration step). Repeated determinations of standard solutions gave a 3.5% RSD (n=10, 0.010M) for repeatability and a 3.2% RSD (n=2, 0.057M) for reproducibility. Samples results (n=9) were in good agreement (t-test) with those obtained with a reference procedure.     

极谱双点滴定法测定奎宁类药物

本文提出以0.1 mol/KI、0.025％聚乙烯醇为底液,以CdCl_2标准溶液为滴定剂,用极谱双点滴定法测定奎宁。该方法具有简便、快速等优点。     

Robust flow-batch coulometric/biamperometric titration system: determination of bromine index and bromine number of petrochemicals

A flow–batch system was constructed and evaluated to perform coulometric titrations with biamperometric end point detection. The flow section of the system is employed for sampling by injecting a sample volume (50–300 μL) in a flow injection-like system. About 1.5 mL of a suitable carrier solution is delivered by a peristaltic pump in order to quantitatively transfer the sample to the system titration cell (2.0 mL total inner volume). The carrier contains the coulometric precursor for the titrant species. The cell contains two pairs of platinum electrodes used for coulometric generation of reagent and biamperometric detection and is actively stirred. The titrant species is generated and the titration is performed by the usual batch procedure with the excess of titrant being detected by biamperometry following the analysis of the titration curve. System operation is computer controlled and all operations are automated, including titration curve analysis and cell cleaning after the titration is ended. The system is characterized by its robustness because its operation does not depend on flow rates, and the work using coulometric methods which generate gases at the counter-electrode is not troublesome. The flow–batch system has been evaluated for determination of bromine index and bromine number (relative to the total reactive olefin content) in petrochemicals according to an ASTM procedure. Typical precision (R.S.D.) is between 0.5 and 6% for different petrochemicals whose bromine number/index vary from 1000 to 10 mg of bromine per 100 g of sample, respectively. Recoveries for standard additions are between 92 and 123% for 10 mg of Br₂ per 100 g increments and 98 to 101% for 100 mg per 100 g increments. Accuracy of the proposed system was evaluated against results obtained by the standard ASTM with no significant difference detected at 95% confidence level.     

Electrochemical detection of parathion at a glassy-carbon electrode modified with hexadecane

A modified electrode, based on a hexadecane (C(16))-coated glassy-carbon electrode (GCE) has been developed for the determination of parathion. The electrochemical behavior of parathion was investigated by cyclic voltammetry (CV). The peak potential and peak current were found to depend on the supporting electrolyte and the pH of the buffer solution. The reduction currents for parathion were proportional to parathion concentration over the range 8x10(-8)-2x10(-5) mol L(-1). The detection limit was 2x10(-8) mol L(-1) parathion for an accumulation time of 30 s. The effects of organic and inorganic species on the determination of parathion were also studied. A procedure was developed to extract parathion from spiked soil samples using a mixture of dichloromethane and acetone as the extraction solvent. The complete extraction and analytical procedure are simple, inexpensive and rapid. Parathion was determined in a soil sample by use of linear scan voltammetry (LSV).     

N,N'-disalicylidene-1,3-diaminopropane as a selective chelating titrant for copper(II)

This study was carried out to develop a new complexometric titration method for determination of copper. For this purpose, the standard solutions of copper(II) (10(-3)-10(-5) M) were potentiometrically titrated using N,N'-disalicylidene-1,3-diaminopropane (Schiff base) as titrant and copper(II)-selective electrode for end-point indication in both ammonium acetate and ammonia/ammonium chloride buffer media. The stoichiometry of titration reaction and interference effects of some metal ions on titration of copper were discussed. There was a good agreement between the results obtained by the proposed titration method and ethylenediaminetetraacetic acid (EDTA) titration method. The accuracy and precision of Schiff base method were tested by five replicate determinations both on the standard solution of copper(II) and standard reference materials. The results have indicated that the percentage of copper in alloys can be safely determined by using the Schiff base method without interference from many other metals in alloys.     

Determination of hardness in tapwater and upland soil extracts using a long-term stable divalent cation selective electrode based on a lipophilic acrylate resin as a membrane matrix

A divalent cation-selective electrode, which utilizes a lipophilic resin as a matrix for the sensing membrane, and which has long-term stability has been developed. The sensing membrane is a lipophilic acrylate resin which is impregnated with a solution of 1-decylalcohol and the calcium salt of bis[4-(1,1,3,3-tetramethylbutyl) phenyl] phosphate at concentrations of 0.08 g ml(-1) each. The electrode exhibited nearly equal selectivity to Ca(2+) and Mg(2+) ions and could be used as a water hardness sensor. The electrode shows a Nernstian response with a slope of 29 mV decade(-1) to both Ca(2+) and Mg(2+) ions in the concentration range from 10(-5) M to 10(-1) M and could be used in the pH range from 3 to 10 for the determination of 10(-3) M Ca(2+) and Mg(2+) solutions. The initial performance of the electrode could be maintained for 1 year, since the lifetime test of the electrode was conducted in tapwater at a continuous flow rate of 4 ml min(-1). The hardnesses of tapwater and upland soil extracts were determined using the developed electrode and the analytical results were in good agreement with those obtained by chelatometric titration using an EDTA solution as the titrant. A coefficient factor of correlation 0.998 was obtained between the electrode method and titrimetry. The long-term stability of the electrode was found to be due to strong affinity of 1-decylalcohol to the lipophilic acrylate resin.