Structure‐Property Optimizations in Donor Polymers via Electronics,Substituents, and Side Chains Toward High Efficiency Solar Cells

Many advances in organic photovoltaic efficiency are not yet fully understood and new insight into structure‐property relationships is required to push this technology into broad commercial use. The aim of this article is not to comprehensively review recent work, but to provide commentary on recent successes and forecast where researchers should look to enhance the efficiency of photovoltaics. By lowering the LUMO level, utilizing electron‐withdrawing substituents advantageously, and employing appropriate side chains on donor polymers, researchers can elucidate further aspects of polymer‐PCBM interactions while ultimately developing materials that will push past 10% efficiency.     

Effect of Extended π‐Conjugation Structure of Donor–Acceptor Conjugated Copolymers on the Photoelectronic Properties

New donor–acceptor conjugated copolymers based on alkylthienylbenzodithiophene (BDTT) and alkoxynaphthodithiophene (NDT) have been synthesized and compared with their benzo[1,2‐b:4,5‐b′]dithiophene (BDT)‐based analogues to investigate the effect of the extended π conjugation of the polymer main chain on the physicochemical properties of the polymers. A systematic investigation into the optical properties, energy levels, field‐effect transistor characteristics, and photovoltaic characteristics of these polymers was conducted. Both polymers demonstrated enhanced photovoltaic performance and increased hole mobility compared with the BDT‐based analogue. However, the BDTT‐based polymer (with π‐conjugation extension perpendicular to main chain) gave the highest power conversion efficiency of 5.07 % for the single‐junction polymer solar cell, whereas the NDT‐based polymer (with π‐conjugation extension along the main chain) achieved the highest hole mobility of approximately 0.1 cm² V^?1 s^?1 based on the field‐effect transistor; this indicated that extending the π conjugation in different orientations would have a significant influence on the properties of the resulting polymers.     

Benzo[2,1‐b;3,4‐b′]dithiophene‐based low‐bandgap polymers for photovoltaic applications

The synthesis of four alternating copolymers using benzo[2,1‐b;3,4‐b′]dithiophene (BDP) as the common donor unit is presented. Before the synthesis, theoretical calculations that we performed predicted that the incorporation of BDP, which consists of fused dithiophene units with a benzene ring, into these polymers would produce a low‐lying highest occupied molecular orbital (HOMO) energy level. Low‐lying HOMO levels are desirable to produce high open circuit voltages (V_OC) in organic bulk heterojunction (BHJ) photovoltaic devices. The polymers' structural characterization, as well as the preliminary results of their performance in BHJ devices, using (6,6)‐phenyl C₆₁‐butyric acid methyl ester as the electron acceptor, is presented. The V_OC values follow the expected trend: increasing with decreasing HOMO level of the polymer. High V_OC values of 0.81 and 0.82 V have been obtained from two polymers: PBDPBT and PBDPDPP. The initial power conversion efficiency achieved in these unoptimized devices was 1.11% because of relatively low J_SC values. The variation observed in the J_SC values between the four polymers is discussed. Device performance is expected to increase with optimization of processing conditions for the devices. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Recent Advances in Mechanically Robust and Stretchable Bulk Heterojunction Polymer Solar Cells

Organic bulk heterojunction solar cells are promising candidates as future photovoltaic technologies for large‐scale and low‐cost energy production. It is, therefore, not surprising that research on the design and preparation of these types of organic photovoltaics has attracted a lot of attention since the last two decades, leading to constantly growing values of energy conversion and efficiency. Combined with the possibility of a large‐scale production via roll‐to‐roll printing techniques, bulk heterojunction solar cells enable the fabrication of conformable, light‐weight and flexible light‐harvesting devices for point‐of‐use applications. This perspective review will highlight the recent advances toward mechanically robust and intrinsically stretchable bulk heterojunction solar cells. Mechanically robust fullerene‐based and all‐polymer devices will be presented, as well as a comprehensive overview of the recent challenges and characterization techniques recently developed to overcome some of the challenges of this research area, which is still in its infancy.     

Synthesis of ω‐anthracenyl‐functionalized soluble polyphenylene: effect of the end‐group on optical and electrical properties

ω‐Anthracenyl‐functionalized soluble polyphenylene (AN‐SPP) with a well‐controlled polymer chain was synthesized. The optical and electrical properties were strongly affected by the anthracenyl end‐group. The UV absorption and photoluminescence emission were enhanced and shifted toward the longer wavelength region in comparison to that of soluble polyphenylene. The optical band gap energies of the main chain and the anthracenyl end‐group were 3.15 and 3.89 eV, respectively. The highest occupied molecular orbital/lowest unoccupied molecular orbital energy levels of the main chain and the anthracenyl end‐group of AN‐SPP were ?4.98/?1.81 eV and ?7.25/?3.36 eV, respectively. The current–voltage characteristics of AN‐SPP were controllable by the presence of the anthracenyl end‐group. Copyright © 2008 John Wiley & Sons, Ltd.     

Synthesis and characterization of polythiophene derivatives with nitrogen heterocycles on the side chain

The Grignard metathesis reaction of 2,5‐dibromo‐3‐(5′‐hexylpyridine‐2′‐yl)thiophene ( M1 ) with i‐PrMgCl afforded 5‐bromo‐2‐chloromagnesio‐3‐(5′‐hexylpyridine‐2′‐yl)thiophene ( GM1 ) in the 86% selectivity. The Kumada coupling polymerization by Ni(dppp)Cl₂ gave poly M1 having the roughly controlled molecular weight between 6700 and 23,400. The characterization using the gel permeation chromatographic and matrix‐assisted laser desorption/ionization‐time of flight mass spectra indicated the diffusion of the nickel catalyst from the propagating end. Based on the GC and ¹H NMR spectra, the head‐to‐tail content of poly M1 was calculated to be 89%. The regioselective Grignard metathesis reactions of 5,5′‐dibromo‐4‐(5″‐hexylpyridine‐2″‐yl)‐2,2′‐bithiophene ( M2 ) and 5,5′‐dibromo‐4‐(5″‐hexylpyrimidine‐2″‐yl)‐2,2′‐bithiophene ( M3 ) also occurred at the ortho‐position of the nitrogen heterocycle. The Kumada coupling polymerizations gave poly M2 and poly M3 having the head‐to‐tail content of 75% and 85%, respectively. The UV–vis spectra of polymers suggested that the polymer conformation becomes more planar in the order of poly M1 < poly M3 < poly M2 , which was investigated by the theoretical calculation of the model oligomers. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2166–2174     

The Polymer Physics of Multiscale Charge Transport in Conjugated Systems

Conjugated polymers are promising candidates for next‐generation low‐cost flexible electronics. Field‐effect transistors comprising conjugated polymers have witnessed significant improvements in device performance, notably the field‐effect mobility, in the last three decades. However, to truly make these materials commercially competitive, a better understanding of charge‐transport mechanisms in these structurally heterogeneous systems is needed for providing systematic guides for further improvements. This review assesses the key microstructural features of conjugated polymers across multiple length scales that can influence charge transport, with special attention given to the underlying polymer physics. The mechanistic understanding from collective experimental and theoretical studies point to the importance of interconnected ordered domains given the macromolecular nature of the polymeric semiconductors. Based on the criterion, optimization to improve charge transport can be broadly characterized by efforts to (a) promote intrachain transport, (b) establish intercrystallite connectivity, and (c) enhance interchain coupling. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1559–1571     

Enhanced thermal conductivity of rheologically percolated carbon nanofiber reinforced polypropylene composites

Three different types of carbon nanofibers (CNF) were incorporated in the same polypropylene (PP) matrix by twin‐screw extrusion. The rheological and thermal properties were investigated. The rheological characterization of CNFs/PP composites as function of their volume fraction shows different microstructures: percolated and non‐percolated behaviors of their CNF's networks. In this work, the laser flash technique is employed in the experimental determination of the thermal diffusivity and conductivity of composites at room temperature. The ultimate aim is to correlate microstructure described by rheological analysis with final thermal properties. The results show that thermal diffusivity and conductivity are clearly higher for rheologically percolated composites suggesting that above certain critical content of nanofibers thermal transport is mainly controlled by percolated structures caused by interconnected CNFs' networks. Finally, thermal conductivity results are described by means of percolation theory from which an intrinsic thermal conductivity for the CNFs' network of approximately 6.5 W/m K, i.e. close to three times lower than some values reported in literature for SWCNTs' networks, was calculated. Copyright © 2015 John Wiley & Sons, Ltd.     

Surfactant‐Assisted Nanocrystalline Zinc Coordination Polymers: Controlled Particle Sizes and Synergistic Effects in Catalysis

Different morphologies and particle sizes of two crystalline zinc‐based coordination polymers (CPs), [Zn(pytz)H₂O]_n ( 1 ; H₂pytz=2,6‐bis(tetrazole)pyridine) and [Zn₂(pytz)₂4 H₂O] ( 2 ), from the bulk scale to the nanoscale, could be obtained under solvothermal conditions with different surfactants (polyvinylpyrrolidone (PVP) or polyethylene glycol (PEG) 2000) as templates. PVP and PEG 2000 could act as capping and structure‐directing agents, respectively, to influence the growth of crystalline particles and control their sizes. CP 1 exhibits a two‐dimensional framework with window‐like units and 2 shows a bimetallic structure. Nanocrystalline 1 and 2 were used as heterogeneous catalysts to study how adjacent catalytic active sites synergistically effected their catalytic reactivities in the direct catalytic conversion of aromatic dinitriles into oxazolines. The results showed that 1 produced bis‐oxazolines as the sole products, whereas 2 gave the mono‐oxazolines as the major products under the same reaction conditions.     

Toward low‐band gap dithienophosphole copolymers for an application in organic solar cells

Two functionalized dithieno[3,2‐b:2′,3′‐d]phospholes with solubilizing groups have been synthesized that allow for the generation of a series of π‐conjugated AB‐ and ABC‐copolymers. The polymers obtained show notable optoelectronic properties with red‐shifted absorption and emission in the orange to red section of the optical solar spectrum. Although combination of dithienophosphole units with fluorene building blocks gives access to processable polymers with band gaps between 2.2 and 2.3 eV in solution and 2.0 eV in the solid state, an ABC copolymer based on dithienophosphole, fluorene, and bis(thienyl)benzothiadiazole units was found to not only exhibit a suitable band gap for solar cell applications (solution: 2.0 eV; solid state: 1.7 eV) but also showed good solubility as well as good electron transfer properties in the presence of fullerene (C₆₀). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 8179–8190, 2008     

Gilch Synthesis of Poly(ortho‐Phenylene Vinylenes): A Powerful Access to High‐Molecular‐Weight Blue‐Emitting Polymers

For the first time, the successful Gilch synthesis of poly(ortho‐phenylene vinylenes) (ortho‐PPVs) is reported. The molar mass of the constitutionally homogeneous ortho‐PPVs reaches values as high as M_w ≈ 300 000 Da. The ortho‐connectivity of the repeating units forces the chains to assume closely packed conformations even in good solvents. Significant perturbation of the π–electron systems and considerable shortening of the conjugation lengths are the consequences. UV–vis absorption and photoluminescence maxima consequently are shifted clearly toward shorter wavelengths compared to, e.g., classic para‐PPVs.

     

Small band gap conjugated polymers based on thiophene–thienopyrazine copolymers

In this study, five small band gap thiophene ( TH )–thienopyrazine ( TP ) conjugated copolymers were synthesized by Stille‐coupling reaction. The polymer structures consisted of one to four thiophene rings with the TP of different side groups provided a systematical investigation on the structure–electronic property relationship. The absorption maxima of the polymer films decreased from 850 to 590 nm as the thiophene moieties increased from thiophene to quaterthiophene. The optical and electrochemical band gaps of the studied poly[2,3‐didodecyl‐5‐(thiophen‐2‐yl)thieno[3,4‐b]pyrazine] ( PTHTP‐C12 ) were 0.97 and 0.78 eV, respectively, indicating a significant intramolecular charge transfer. The theoretical geometry and electronic properties of the TH ‐ TP copolymers by the density functional theory at the B3LYP level and 6‐31G(d) basis set suggested that the bond length alternation enlarged with enhancing the thiophene content and resulted in the variation on the polymer band gap. The relatively small theoretical effective mass of poly( TH ‐alt‐ TP ) also indicated its potential applications for field transistor applications. Our study demonstrates the tunable electronic properties of small band gap copolymers by the thiophene content and the resulted geometry variation. Such polymers could be potentially used for near‐infrared electronic and optoelectronic devices. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5872–5883, 2007     

Copolymers of fluorene and thiophene with conjugated side chain for polymer solar cells: Effect of pendant acceptors

Two copolymers of fluorene and thiophene with conjugated side‐chain pending acceptor end group of cyanoacetate ( P2 ) and malononitrile ( P3 ) were synthesized. Both polymers exhibit good thermal stability and low highest occupied molecular orbital level (?5.5 eV). In comparison with P2 , P3 exhibits stronger UV–vis absorption and higher hole mobility. Polymer solar cells based on P3 :PC₇₁BM exhibits a power conversion efficiency of 1.33% under AM 1.5, 100 mW/cm², which is three times of that based on P2 :PC₇₁BM. The higher efficiency is attributed to better absorption, higher hole mobility, and the reduced phase separation scale in P3 :PC₇₁BM blend. The aggregate domain size in P3 :PC₇₁BM blend is 50 nm, much smaller than that in P2 :PC₇₁BM blend (200 nm). Tiny difference in the end groups on side chains of P2 and P3 leads to great difference in phase separation scale, charge transport, and efficiency of their photovoltaic devices. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Emulsion and Foam Templating—Promising Routes to Tailor‐Made Porous Polymers

Emulsions, foams, and foamed emulsions have been used successfully as templates for the synthesis of macroporous polymers. Based on this knowledge this Minireview presents strategies to use, optimise, and upscale these templating methods to synthesise tailor‐made porous polymers. The uniqueness of such polymers lies in the ability to tailor their structures and, therefore, their properties. However, systematic studies on structure–property relations are lacking mainly because the templating scientific community is “split into two”: the polydisperse and monodisperse camps. Thus, it is time to build a bridge between the camps, that is, to synthesise porous polymers with very different structures from the same precursors to determine the relationship between the structure and the properties.     

Effect of Guanidinylation on the Properties of Poly(2‐aminoethylmethacrylate)‐Based Antibacterial Materials

The effect of converting ammonium into guanidine moieties, compared to other factors such as molecular weight or hydrophobicity, on the antibacterial activity is investigated for homo‐ and copolymers of 2‐aminoethylmethacrylate in solution or coatings. Polymers are obtained by free radical polymerization, polymer‐analogous guanidinylation is conducted with cyanamide; non‐leaching immobilization is achieved by LBL assembly of homopolymers or crosslinking of functional sidegroups in copolymers. Antibacterial activity to Escherichia coli or Bacillus subtilis is determined by different standard methods. Guanidinylation improves antibacterial activity and speed as well as cytotoxicity of hydrophilic homo‐ and copolymers in solution or coatings.

     

Band‐gap engineering of polythiophenes via dithienophosphole doping

A series of polythiophenes doped with dithieno[3,2‐b:2′,3′‐d]phosphole units at varying levels (0–17%) were synthesized and characterized. Polymer work up provided two series of polymers from chloroform (C) and hexanes (H) for each doping level, respectively. Systematic structure–property studies revealed that the C‐series polymers generally had higher molecular weights than the H‐series, but also slightly higher relative dithienophosphole concentrations, both having a significant impact on the photophysical and electrochemical properties of the polymers. Furthermore, the presence of the dithienophosphole units also stabilizes the LUMO levels, whereas the HOMO levels remain dominated by the thiophene units, resulting in desirable electronics for an interaction with acceptor materials, such as 1‐(3‐methoxycarbonyl)propyl‐1‐phenyl[6,6]C₆₁. Importantly, increasing amount of dithienophosphole doping results in increased conductivities for the polymers in their oxidized state, while concurrently significantly stabilizing the neutral polythiophenes toward oxidation under environmental conditions. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

PEG‐Induced Synthesis of Coordination‐Polymer Isomers with Tunable Architectures and Iodine Capture

Controllable synthesis of coordination polymer (CP) isomers and revealing their structure–property relationships remain enormous challenges. Three new supramolecular isomers have been synthesized by tuning the poly(ethylene glycol) (PEG) content in the feed. These supramolecular isomers have the same framework formula of [Cu₂I₂(tppe)] and different architectures from the classical 2D stacking framework to a 3D entangled system with the coexistence of interpenetration and polycatenation, and a 3D topological framework. Interestingly, these CPs could be utilized for capturing iodine molecules. According to multiple complementary experiments and crystallographic analyses, iodine capture is mainly based on halogen‐bond interactions in the inorganic {Cu₂I₂} building blocks of the framework. The present study describes a structure–property relationship in supramolecular isomerism with distinct topological structures.     

Effect of architecture on the tensile properties of triblock copolymers in a lamellar phase.

We have used self-consistent field theory to calculate the tensile moduli of triblock copolymers in lamellar microstructures prepared from linear and star architectures. The extensional moduli K(33) are the main contributors to the tensile moduli, and the contribution of K(U)33 (the internal energy contribution to K(33)) is the main component of the value of K(33). We find that the tensile moduli of ABC three-miktoarm star terpolymers are smaller than those of ABC linear triblock copolymers having identical components, presumably for two main reasons. First, for the ABC three-miktoarm star terpolymers, the contributions of K(U)33 are larger than those of the linear triblock copolymers; we attribute this phenomenon to the star terpolymers having smaller lamellar domain sizes at equilibrium relative to those of the linear triblock copolymers. Second, conformational entropies play an important role in affecting the tensile moduli, mainly because of the different degrees of freedom of the various chains. In contrast, the shear moduli contribute negligibly to the tensile moduli.     

Chemical Modification in the Design of Immobilized Enzyme Biocatalysts: Drawbacks and Opportunities

Chemical modification of enzymes and immobilization used to be considered as separate ways to improve enzyme properties. This review shows how the coupled use of both tools may greatly improve the final biocatalyst performance. Chemical modification of a previously immobilized enzyme is far simpler and easier to control than the modification of the free enzyme. Moreover, if protein modification is performed to improve its immobilization (enriching the enzyme in reactive groups), the final features of the immobilized enzyme may be greatly improved. Chemical modification may be directed to improve enzyme stability, but also to improve selectivity, specificity, activity, and even cell penetrability. Coupling of immobilization and chemical modification with site‐directed mutagenesis is a powerful instrument to obtain fully controlled modification. Some new ideas such as photoreceptive enzyme modifiers that change their physical properties under UV exposition are discussed.