A localized surface plasmon resonance and light confinement‐enhanced near‐infrared light photodetector

Light manipulation is paramountly important to the fabrication of high‐performance optoelectronic devices such as solar cells and photodetectors. In this study, a high‐performance near‐infrared light nanophotodetector (NIRPD) was fabricated based on a germanium nanoneedles array (GeNNs array) with strong light confining capability, and single‐layer graphene (SLG) modified with heavily doped indium tin oxide nanoparticles (ITONPs), which were capable of inducing localized surface plasmon resonance (LSPR) under NIR irradiation. An optoelectronic study shows that after modification with ITONPs the device performance including photocurrent, responsivity and detectivity was considerably improved. In addition, the ITONPs@SLG/GeNNs array NIRPD was able to monitor fast‐switching optical signals, the frequency was as high as 1 MHz, with very fast response rates. Theoretical simulations based on finite‐element method (FEM) revealed that the observed high performance was not only due to the strong light‐confining capability of the GeNNs array, but also due to the plasmonic ITONPs‐induced hot electron injection. The above results suggest that the present NIRPD will have great potential in future optoelectronic devices application.

     

Bi‐directional organic light‐emitting diodes with nanoparticle‐enhanced light outcoupling

An effective method is presented for enhancing the outcoupling efficiency of translucent/bi‐directional organic light‐emitting diodes (TL/BD‐OLEDs) with a bottom indium tin oxide (ITO) anode and a top cathode comprised of a thin Ag layer covered with an organic capping layer. Upon insertion of a nanoparticle (NP)‐based scattering layer (NPSL) between the substrate and the ITO anode, the TL/BD‐OLEDs exhibit significantly enhanced external quantum efficiency (EQE) in both emission directions. Furthermore, the NPSL improves the color stability of the TL/BD‐OLEDs over a wide range of viewing angles. Simulations based on geometrical and statistical optics are performed to elucidate the mechanism by which the efficiency is enhanced and to establish strategies for further optimization. Simulations performed on the scattering layers with varying NP volume percentage reveal that the bottom‐side emission is governed by competition between waveguide‐mode extraction and backward scattering by NPs in the film, while the top‐side emission is largely dominated by the latter. Optimized bi‐directional OLEDs achieve a 1.64‐fold enhanced EQE compared to reference devices without NPSL.     

High efficiency rubrene based inverted top-emission organic light emitting devices with a mixed single layer

Inverted top-emission organic light emitting devices (TEOLEDs) with a mixed single layer by mixing of electron transport materials (PyPySPyPy and Alq₃), hole transport material (α-NPD) and dope material (rubrene) were investigated. Maximum power efficiency of 3.5 lm/W and maximum luminance of 7000 cd/m² were obtained by optimizing the mixing ratio of PyPySPyPy:Alq₃:α-NPD:rubrene=25:50:25:1. Luminance and power efficiency of mixed single layer device were two times improved compared to bi-layer heterojunction device and tri-layer heterojunction device. Lifetime test also shows that the mixed single layer device exhibits longer operational lifetimes of 343 h, which is three times longer than the 109 h for tri-layer device, and two times longer than the 158 h for bi-layer device. In addition, the maximum luminance and power efficiency were obtained at 20,000 cd/m² and 7.5 lm/W, respectively, when a TPD layer of 45 nm was capped onto the top metal electrode.     

Simplified hybrid white organic light‐emitting diodes with efficiency/efficiency roll‐off/color rendering index/color‐stability trade‐off

A high‐performance hybrid white organic light‐emitting diode (WOLED) based on a simple structure has been developed. The resulting device exhibits a maximum total current efficiency and power efficiency of 35.7 cd/A and 30.6 lm/W, respectively. Even at a high luminance of 1000 cd/m², a current efficiency of 32.0 cd/A and a power efficiency of 19.4 lm/W are obtained, suggesting that the device exhibits a low efficiency roll‐off. Besides, the device shows excellent color‐stability during a wide range of luminance and a high color rendering index (CRI) of 83 is obtained. Moreover, the origin of the superior properties is explored comprehensively. Such achieved results demonstrate that high efficiency, low efficiency roll‐off, stable color and high CRI can be simultaneously realized in a simplified hybrid WOLEDs. (© 2014 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Functional organic single crystals for solid‐state laser applications

In the article by Hong‐Hua Fang et al. (doi: http://dx.doi.org/10.1002/lpor.201300222 ), published in Laser Photonics Rev. 8, 687–715 (2014), the names of two authors in references were wrongly spelt and citations in the text were missing. This erratum is published to correct this.     

Functional organic single crystals for solid‐state laser applications

Because of long‐range order and high chemical purity, organic crystals have exhibit unique properties and attracted a lot of interest for application in solid‐state lasers. As optical gain materials, they exhibit high stimulated emission cross section and broad tunable wavelength emission as similar to their amorphous counterpart; moreover, high purity and high order give them superior properties such as low scattering trap densities, high thermal stability, as well as highly polarized emission. As electronic materials, they are potentially able to support high current densities, thus making it possible to realize current driven lasers. This paper mainly describes recent research progress in organic semiconductor laser crystals. The building molecules, crystal growth methods, as well as their stimulated emission characteristics related with crystal structures are introduced; in addition, the current state‐of‐the‐art in the field of crystal laser devices is reviewed. Furthermore, recent advances of crystal lasers at the nanoscale and single crystal light‐emitting transistors (LETs) are presented. Finally, an outlook and personal view is provided on the further developments of laser crystals and their applications.     

聚对二甲苯薄膜的制备及其在有机电致发光二极管中的应用研究

使用自制的分子束源制备了聚对二甲苯（Parylene N,PPXN）薄膜。通过对该分子束源的设计和不断优化,PPXN薄膜可以在室温、10-3 Pa的较低反应压强下以0.01 nm/s~0.02 nm/s的速率沉积聚合。用红外透射光谱和原子力显微镜测量了PPXN薄膜的成分和表面形貌。结果表明,所制备的薄膜成分为PPXN,薄膜呈波浪状、无尖刺的表面形貌。准确控制的PPXN薄膜在有机电致发光二极管中用作缓冲层,对载流子的注入和传输进行调控,有效地改善了器件内部的载流子平衡。最优化结构的器件较未插入PPXN缓冲层的器件,电流效率提高80%以上。     

A flexible blue light sensitive organic photodiode with high properties for the applications in low‐voltage‐control circuit and flexion sensors

Low‐voltage‐control circuit is one of the most important parts of the modern electrical control system due to the avoidance of operation risk and easy automation. Here, based on a C₆₀: m‐MTDATA bulk heterojunction, a blue‐light‐sensitive organic photodiode (OPD) is explored for the development of flexible low‐voltage‐control circuit. The control of circuit under 2000 V high voltage is achieved. The influences of the organic‐layer thickness, the donor/acceptor volume ratio and the matching of energy levels on the photocurrent are investigated. The maximum light/dark current ratio and current transfer ratio of 1.3 × 10⁴ and 1.3% are achieved, respectively. The highest photoresponse is up to 130 mA/W, markedly higher than some commercial inorganic photodiodes. This device could also be used as flexion and mechanical force sensors with the current density changing under different bending conditions. Therefore, this sort of OPD has a promising application in low‐voltage‐controlled, high‐voltage‐endurable hands for intelligent robots.     

ITO‐free top emitting organic light emitting diodes with enhanced light out‐coupling

Bottom emitting organic light emitting diodes (OLEDs) can suffer from lower external quantum efficiencies (EQE) due to inefficient out‐coupling of the generated light. Herein, it is demonstrated that the current efficiency and EQE of red, yellow, and blue fluorescent single layer polymer OLEDs is significantly enhanced when a MoO_x(5 nm)/Ag(10 nm)/MoO_x(40 nm) stack is used as the transparent anode in a top emitting OLED structure. A maximum current efficiency and EQE of 21.2 cd/A and 6.7%, respectively, was achieved for a yellow OLED, while a blue OLED achieved a maximum of 16.5 cd/A and 10.1%, respectively. The increase in light out‐coupling from the top‐emitting OLEDs led to increase in efficiency by a factor of up to 2.2 relative to the optimised bottom emitting devices, which is the best out‐coupling reported using solution processed polymers in a simple architecture and a significant step forward for their use in large area lighting and displays.     

Efficient top-emitting white organic light emitting device with an extremely stable chromaticity and viewing-angle

In this paper,we report on the fabrication of a top-emitting electrophosphorescent p-i-n white organic lightemitting diode on the basis of a low-reflectivity Sm/Ag semi-transparent cathode together with a thickness-optimized ZnS out-coupling layer.With a 24-nm out-coupling layer,the reflectivity of the cathode is reduced to 8% at 492 nm and the mean reflectivity is 24% in the visible area.By introducing an efficient electron blocking layer tris(1phenylpyrazolato,N,C2 ’)iridium(III)(Ir(ppz) 3) to confine the exciton recombination area,the current efficiency and the colour stability of the device are effectively improved.A white emission with the Ir(ppz) 3 layer exhibits a maximum current efficiency of 9.8 cd/A at 8 V,and the Commission Internationale de L’Eclairage(CIE) chromaticity coordinates are almost constant during a large voltage change of 6 V-11 V.There is almost no viewing angular dependence in the spectrum when the viewing angle is no more than 45,with a CIE x,y coordinate variation of only(±0.0025,±0.0008).Even at a large viewing angle(75),the CIE x,y coordinate change is as small as(±0.0087,±0.0013).     

Air stability of PTCDI‐C13‐based n‐OFETs on polymer interfacial layers

This Letter reports the novel use of poly(9‐vinylcarbazole) (PVK) as a dielectric interfacial layer for n‐type organic field‐effect transistors (n‐OFETs). With PVK, both the air stability and electron mobility of N,N′‐ditridecylperylene‐3,4,9,10‐tetracarboxylic diimide (PTCDI‐C13)‐based OFETs were improved. Among the PVKs with different weight‐average molecular weight (M_w), PVK with high M_w showed good performance. The high glass transition temperature of PVK enabled thermal post annealing of the active layer, which resulted in a high electron mobility of 0.61 cm²/Vs. This mobility was maintained at 90% and 59% after 4 days and 105 days in air, respectively. The PVK interfacial layer reduced the trapped charges in the PTCDI‐C13‐based n‐OFET for air‐exposure and caused a decrease in the threshold voltage shift.

     

Development of organic light‐emitting diodes for electro‐optical integrated devices

Organic light‐emitting diodes (OLEDs) are discussed for electro‐optical integrated devices that are used for optical signal transmission. Organic optical devices including polymeric optical fibers are used for optical communication applications to realize polymeric electro‐optical integrated devices. The OLEDs were fabricated by vacuum process, i.e. the organic molecular beam deposition (OMBD) technique or a solution process on a polymeric or a glass substrate, for comparison. Optical signals faster than 100 MHz have been created by applying pulsed voltage directly to the OLED utilizing rubrene doped in 8‐hydoxyquinolinum aluminum (Alq₃), as an emissive layer. OLEDs fabricated by solution process utilizing rubrene doped in carrier‐transporting materials have also discussed. OLEDs utilizing polymeric materials by solution process are also fabricated and discussed. Moving‐picture signals are transmitted utilizing both vacuum‐ and solution‐processed OLEDs, respectively.     

UV/ozone‐treated WS2 hole‐extraction layer in organic photovoltaic cells

WS₂ nanosheets obtained through a simple sonication exfoliation method are employed as a hole‐extraction layer to improve the efficiency of organic photovoltaic cells (OPVs). A reduction in the wavenumber difference in the Raman spectra, the appearance of a UV absorption peak, and atomic force microscopy images indicate that WS₂ nanosheets are formed through the sonication method. The power conversion efficiency (PCE) values of OPVs with and without untreated WS₂ layers are both 1.84%. After performing a UV‐ozone (UVO) treatment on the WS₂ surface for 15 min, the PCE increases to 2.4%. Synchrotron radiation photoelectron spectroscopy data show that the work function of WS₂ increases from 4.9 eV to 5.1 eV upon UVO treat‐ ment, suggesting that the increase in the PCE value is caused by the band alignment. Upon inserting poly(3,4‐ethylenedioxythiophene):poly(styrene‐sulfonate) (PEDOT: PSS) between the WS₂ and the active layer, the PCE value of the OPV increases to 3.07%, which is superior to that of the device employing only PEDOT:PSS (2.87%). Therefore, it is considered that the use of UVO‐treated WS₂ is able to improve the performance of OPV cells. (© 2014 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Graphene‐Based Phosphorus‐Doped Carbon as Anode Material for High‐Performance Sodium‐Ion Batteries

Graphene‐based phosphorus‐doped carbon (GPC) is prepared through a facile and scalable thermal annealing method by triphenylphosphine and graphite oxide as precursor. The P atoms are successfully doped into few layer graphene with two forms of P–O and P–C bands. The GPC used as anode material for Na‐ion batteries delivers a high charge capacity 284.8 mAh g^?1 at a current density of 50 mA g^?1 after 60 cycles. Superior cycling performance is also shown at high charge?discharge rate: a stable charge capacity 145.6 mAh g^?1 can be achieved at the current density of 500 mA g^?1 after 600 cycles. The result demonstrates that the GPC electrode exhibits good electrochemical performance (higher reversible charge capacity, super rate capability, and long‐term cycling stability). The excellent electrochemical performance originated from the large interlayer distance, large amount of defects, vacancies, and active site caused by P atoms doping. The relationship of P atoms doping amount with the Na storage properties is also discussed. This superior sodium storage performance of GPC makes it as a promising alternative anode material for sodium‐ion batteries.     

Light manipulation in organic light‐emitting devices by integrating micro/nano patterns

The demonstration of high efficiency and color tunability has brought organic light‐emitting devices (OLEDs) into the lighting and display market. High efficiency is one of the key issues for their commercial applications, for which much effort has been devoted to developing novel materials and device structures. It is well known that around 80% of the generated photons are trapped in OLED structure, so that there is still the greatest scope for significant improvements in its efficiency. This has driven the research towards the integration of micro/nano patterns into device structures that benefit from their abilities in manipulating the generation and propagation of photons. Micro/nano patterns with random or periodic morphologies have demonstrated their effect on the outcoupling of the trapped photons within the device. Moreover, the emitting properties other than the light extraction could be manipulated by introducing the micro/nano patterns. This article reviews the recent progresses in improving the light extraction and manipulating the emission properties of the OLEDs through the introduction of the micro/nano patterns by various fabrication strategies. The light manipulation of the micro/nano patterns in organic photovoltaics is briefly discussed considering its similar working principle and fabrication strategies to that of the OLEDs.

     

Electroluminescence enhancement in ultraviolet organic light‐emitting diode with graded hole‐injection and ‐transporting structure

Electroluminescent intensity and external quantum efficiency (EQE) in ultraviolet organic light‐emitting diodes (UV OLEDs) have been remarkably enhanced by using a graded hole‐injection and ‐transporting (HIT) structure of MoO₃/N,N ′‐bis(naphthalen‐1‐yl)‐N,N ′‐bis(phenyl)‐benzidine/MoO₃/4,4′‐bis(carbazol‐9‐yl)biphenyl (CBP). The graded‐HIT based UV OLED shows superior short‐wavelength emis‐ sion with spectral peak of ～410 nm, maximum electroluminescent intensity of 2.2 mW/cm² at 215 mA/cm² and an EQE of 0.72% at 5.5 mA/cm². Impedance spectroscopy is employed to clarify the enhanced hole‐injection and ‐transporting capacity of the graded‐HIT structure. Our results provide a simple and effective approach for constructing efficient UV OLEDs. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Investigation of light programmable non‐volatile memory in an organic phototransistor

Excellent non‐volatile memory characteristics have been demonstrated under the optoelectric conditions for organic phototransistors (OPTs). The high photosensitivity shown as reversible shifts in light‐induced V_TH exhibits a large memory window for programming caused by the excited immobile carriers (electron) trapped as a function of the electrical bias and the light intensity. The long life span of stored electrons also reveals promising behavior with respect to data retention as well as the electrical reliability to serve as a data storage medium with the non‐volatile memory characteristic in OPTs. The V_TH recovery accelerated by the reversible bias stress for the stored charges under irradiation shows that the erasing behavior is clearly brought by the discharge process of long‐lived electrons occupied in deep states. Plausible mechanisms in the energy band are discussed for the programming and erasing process, which provides a fundamental understanding of the intrinsic charge storage behavior in OPTs. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

General expression for the depolarization ratio for first‐order collision‐induced light scattering

A general expression that involves only the ranks of the molecular polarizabilties of the two molecules involved in a pair interaction yielding translational and rotational collision‐induced light scattering (CILS) is obtained. It may be used to investigate the behaviour of individual interactions that contribute to the incremental collision‐induced pair polarizability. Copyright © 2010 John Wiley & Sons, Ltd.     

High‐energy‐resolution diced spherical quartz analyzers for resonant inelastic X‐ray scattering

A novel diced spherical quartz analyzer for use in resonant inelastic X‐ray scattering (RIXS) is introduced, achieving an unprecedented energy resolution of 10.53 meV at the Ir L₃ absorption edge (11.215 keV). In this work the fabrication process and the characterization of the analyzer are presented, and an example of a RIXS spectrum of magnetic excitations in a Sr₃Ir₂O₇ sample is shown.