Cs+ and Ba2+ Selective Transport by a Novel Self-Assembled Isoguanosine Ionophore Through Polymer Inclusion and Bulk Liquid Membranes

5'-(Tert-butyldimethylsilyl)-2',3'-O-isopropylidene isoguanosine(isoG 1) serves as a selective Cs⁺ carrier in liquid membrane transport. IsoG~1 is a lipophilic nucleoside that self-assembles via hydrogen bonds and cation-dipole interactions to form a stable decamer sandwich complex with Cs⁺. Using an acidic receiving phase, Cs⁺ transport through polymer inclusion membranes (PIMs) was observed at concentrations of isoG 1 below 21 mM. When isoG 1 was precomplexed with Cs⁺ to give the (isoG 1)₁₀-Cs⁺decamer, flux was observed above 21 mM carrier. The Cs⁺ flux increased with increasing carrier concentration of the precomplexed (isoG 1)₁₀-Cs⁺ decamer. The Cs⁺ transport selectivity by isoG 1 was investigated in the presence of sodium salt solutions of high concentration. Excellent Cs⁺ flux and selectivity over the other alkali metal cations was observed in PIMs and bulk liquid membranes (BLMs). In the absence of Cs⁺, this ionophore exhibitsgood Ba²⁺ selectivity in BLMs.     

Selective Transport of Lead(II) and Strontium(II) Through a Crown Ether-Based Polymer Inclusion Membrane Containing Dialkylnaphthalenesulfonic Acid

New polymer inclusion membranes (PIMs) containing 18-membered crownethers and dialkylnaphthalenesulfonic acid are proposed for Sr2+ and Pb2+removal from nitric acid solutions. The influence of source phasecomposition and stripping agents was characterized and permeabilitycoefficients were calculated. The PIMs are easy to prepare and may be usefulin separation and concentration procedures for these cations from complexmixtures such as nuclear waste. Long-term stability was obtained for atleast several weeks of constant use during which no significant change ofpermeability was observed.     

Selective Transport of Cesium and Strontium Ions Through Polymer Inclusion Membranes Containing Calixarenes as Carriers

Abstract

Cs⁺ and Sr²⁺ are selectively removed over Na⁺ from acidic aqueous solutions with high Na⁺ concentrations by using membranes designed to selectively transport one of the two cations. To this end, calix[4]arene derivatives were used as carriers in polymer inclusion membranes (PIMs). The synthesis and characterization of new calix[4]arene derivatives (a bisamide (2) and three bisesters (3, 5 and 6)) used for the separation of Sr²⁺ are described. Another bisester (4) was employed for the same separation. In addition, a calix[4]arene-crown-6 (7) was incorporated into the membrane for Cs⁺ extraction. The concentration of each membrane component (polymer, carrier and counter-ion) was optimized and the permeability coefficients (P, m sec^?1) of Cs⁺, Sr²⁺ and Na⁺ were determined. A synergistic effect between the calixarenes and dinonylnaphtalenesulfonic acid, used as counterion, (DNNS, 8) was observed. High selectivity of Cs⁺ over Na⁺ and of Sr²⁺ over Na⁺ were obtained with compounds 7 and 3, respectively. The best P for Sr²⁺ was obtained with compound 4. A long-term experiment was carried out to demonstrate the durability of PIMs. PIMs are compared to classical supported liquid membranes.     

Alkyl Ammonium Ion Selectivity of Hexahomotrioxacalix[3]arene Triamide Derivative having the Intramolecular Hydrogen-Bonding Group

The lower rim functionalized hexahomotrioxacalix[3]arene triamide 4 with cone-conformation was synthesized from triol 1 by a stepwise reaction. The different extractability for alkali metal ions, transition metal ions, and alkyl ammonium ions from water into dichloromethane is discussed. Due to the strong intramolecular hydrogen bonding between the neighboring NH and CO groups in triamide 4, its affinity to metal cations was weakened. Triamide 4 shows a single selectivity to n-BuNH₃⁺. The anion complexation of triamide 4 was also studied by ¹H NMR titration experiments. Triamide 4 binds halides through the intermolecular hydrogen bonding among the NH hydrogens of amide in a 1:1 fashion in CDCl₃. The association constants calculated from these changes in chemical shifts of the amide protons are K_a = 223 M⁻¹ for Cl⁻ and K_a = 71.7 M⁻¹ for Br⁻. Triamide 4 shows a preference for Cl⁻ complexation than Br⁻ complexation.     

Selectivity of Transport of Sodium, Magnesium, and Calcium Ions through a Sulfo-Cationite Membrane in Mixtures of Solutions of Their Chlorides

The transport numbers and the selectivity of transport of sodium, magnesium, and calcium ions through a heterogeneous sulfo-cationite membrane in solutions of sodium, magnesium, and calcium chlorides and their mixtures are studied at various current densities. Equations for calculating the selectivity of transport of the ions through the membrane are suggested for two extreme cases. One case corresponds to low currents, when one can assume that the membrane is at equilibrium with the outside solution. The selectivity of transport of the ions is defined in this case by their migration through the membrane. The other case occurs at currents that are close to a limiting value. Under these conditions the transport of the ions through the membrane is defined by their transport through a diffusion layer that forms near the membrane surface. Calculations with the aid of these equations satisfactorily conform to experiment. The deviation from calculation in the case of the magnesium cation is connected probably with its hydration being substantially greater as compared with sodium and calcium. It is established that the selectivity of transport of the ions through the membrane may be controlled to a certain extent by varying the current density.__________Translated from Elektrokhimiya, Vol. 41, No. 8, 2005, pp. 997–1000.Original Russian Text Copyright © 2005 by Greben’, Rodzik.     

Facilitated Transport of Cr(VI) through Polymer Inclusion Membrane System Containing Calix[4]arene Derivative as Carrier Agent

Chromium(VI) is one of the major toxic elements present in environmental samples. The polymer inclusion membrane (PIM), has been developed to provide metal ion transport with high selectivity. This study was conducted to discover efficient methods for removing Cr(VI) from wastewater. A functionalized calix[4]arene carrier 1 in a PIM system was used to transport Cr(VI) from an acidic aqueous donor phase solution to an acceptor phase that contained an acetic acid/ammonium acetate solution at pH 6. The prepared PIM was characterized with Fourier Transform Infrared (FT-IR) spectroscopy and the Atomic Force Microscopy (AFM) techniques as well as with contact angle measurements. The efficiency of Cr(VI) transport through the PIM was investigated by studying the effects of carrier concentration on the membrane phase as well as by measuring the amount of plasticizer in the membrane, the pH in the acceptor phase and the membrane's stability and thickness. The kinetic parameters were calculated as rate constant (k), permeability coefficient (P), flux (J) and diffusion coefficient (D_o). The transport efficiency of Cr(VI) was observed to be 98.61% after 10 h under optimized conditions. The experimental results show that Cr(VI) can transport from the donor phase to the acceptor phase with high efficiency through the PIM. The results also suggest that the transport efficiency of the PIM was reproducible and that a PIM is effective for long-term separation processes.     

Transport Selectivity of a Diethylene Glycol Dimethacrylate- Based Thymine-imprinted Polymeric Membrane over a Cellulose Support for Nucleic Acid Bases

The binding mechanism between 9-vinyladenine and pyrimidine base thymine in methanol was studied with UV-visible spectrophotometric method. Based on this study, using thymine as a template molecule, 9-vinyladenine as a novel functional monomer and diethylene glycol dimethacrylate as a new cross-linker, a specific diethylene glycol dimethacrylate-based molecularly imprinted polymeric membrane was prepared over a cellulose support. Then, the resultantly polymeric membrane morphologies were visualized with scanning electron microscopy and its permselectivity was examined using thymine, uracil, cytosine, adenine and guanine as substrates. This result showed that the imprinting polymeric membrane prepared with diethylene glycol dimethacrylate exhibited higher transport capacity for the template molecule thymine and its optimal analog uracil than other nucleic acid bases. The membrane also took on higher permselectivity than the imprinted membrane made with ethylene glycol dimethacrylate as a cross-linker. When a mixture including five nucleic acid bases thymine, uracil, cytosine, adenine and guanine passed through the diethylene glycol dimethacrylate-based thymine-imprinted polymeric membrane, recognition of the membrane for the template molecule thymine and its optimal analog uracil was demonstrated. It was predicted that the molecularly imprinted membrane prepared with diethylene glycol dimethacrylate as cross-linker might be applicable to thymine assay of absolute hydrolysates of DNA or uracil assay of absolute hydrolysates of RNA in biological samples because of its high selectivity for the template molecule thymine and its optimal analog uracil.     

Phosphonium Boranes for the Selective Transport of Fluoride Anions across Artificial Phospholipid Membranes

With the view of developing selective transmembrane anion transporters, a series of phosphonium boranes of general formula [p‐RPh₂P(C₆H₄)BMes₂]⁺ have been synthesized and evaluated. The results demonstrate that variation of the R group appended to the phosphorus atom informs the lipophilicity of these compounds, their Lewis acidity, as well as their transport activity. Anion transport experiments in POPC‐based large unilamellar vesicles show that these main‐group cations are highly selective for the fluoride anion, which is transported more than 20 times faster than the chloride anion. Finally, this work shows that the anion transport properties of these compounds are extremely sensitive to the steric crowding about the boron atom, pointing to the crucial involvement of the Group 13 element as the anion binding site.     

Composite Polymer Electrolytes for Fuel Cell Applications: Filler-Induced Effect on Water Sorption and Transport Properties

Nafion- and sulfonated polysulfone (SPS)- based composite membranes were prepared by incorporation of SnO₂ nanoparticles in a wide range of loading (0 35 wt. %). The composites were investigated by differential scanning calorimetry, dynamic vapor sorption and electrochemical impedance spectroscopy to study the filler effect on water sorption, water mobility, and proton conductivity. A detrimental effect of the filler was observed on water mobility and proton conductivity of Nafion-based membranes. An increase in water mobility and proton conductivity was instead observed in SPS-based samples, particularly at low hydration degree. Analysis of the water sorption isotherms and states of water revealed that the presence of SnO₂ in SPS enhances interconnectivity of hydrophilic domains, while not affecting the Nafion microstructure. These results enable the design of suitable electrolyte materials that operate in proton exchange membrane fuel cell conditions.     

Supramolecular Design Strategy of a Water-Soluble Diphenylguanidine-Cyclodextrin Polymer Inclusion Complex

Diphenylguanidine (DPG) is a widely used secondary accelerator for the vulcanization of natural rubber (NR) latex. However, its low water solubility and high toxicity limit its use in high-end NR products. In this study, a water-soluble inclusion complex of DPG and a β-cyclodextrin polymer (β-CDP), termed DPG-β-CDP, was prepared through supramolecular interactions and characterized using Fourier-transform infrared spectroscopy, ¹H NMR, scanning electron microscopy, and UV-vis spectroscopy techniques. In comparison with that of DPG, the water solubility of DPG-β-CDP was greatly enhanced because of the water-soluble host molecule. The molar ratio of DPG to the CD unit in β-CDP was determined to be 1:1. At 25 °C, the binding constant of DPG-β-CDP was found to be 9.2 × 10⁵ L/mol by UV-vis spectroscopy. The proposed method for forming inclusion complexes with high potential for use as water-soluble vulcanization accelerators is promising.     

Selective metal ion transport through polymer inclusion membrane containing surfactin as carrier reagents

Metal ion selective polymer inclusion membrane (PIM) was prepared by using cellulose triacetate as matrix, surfactin (SF) as ion carrier, and 2-nitrophenyl n-octyl ether as plasticizer. The structure and morphology of the prepared PIM were characterized by means of thermogravimetric analysis, scanning electron microscopy, and Fourier transform infrared spectroscopy. The effects of plasticizer and the amount of SF to ionic membrane flux were investigated, and the optimized component was obtained thereof. The selectivity of the membrane toward metal cation was studied and the order of Ni(II) > Ca(II) > Co(II) > Pb(II) > Cu(II) > Mg(II) was followed. In addition, the durability of the PIM was studied by successive reuse of the membrane, and the ionic flux slightly decreased after five cycles of reuse, indicating the excellent durability of the PIM.     

Selective Transport of Copper(II) Ion across a Polymer Membrane Incorporating a Difunctional Schiff-base Ionophore

The selective polymer membrane transport of Cu(II) from an aqueous solution containing seven metal cations, Co(II), Ni(II), Cu(II), Zn(II), Ag(II), Cd(II) and Pb(II), was studied .The source phase contained equimolar concentrations of the above-mentioned cations, with the source and receiving phases being buffered at pH 4.9 and 3.0, respectively. Cu(II) ion transport occurred (J=2.82 × 10⁻⁷ mol/h at 25 °C) from the aqueous source phase across the polymer membrane (derived from cellulose triacetate) containing ligand (I) as the ionophore, into the aqueous receiving phase. Clear transport selectivity for Cu(II) was observed.     

Electric Field Driven Extraction of Inorganic Anions Across a Polymer Inclusion Membrane

The potential use of plasticized cellulose acetate membranes for electric field driven extraction and preconcentration of inorganic anions was studied. The extraction of highly lipophilic ions such as perchlorate is possible by employing a membrane without any ion carrier, while anions of low lipophilicity, such as phosphate, require a carrier. Best extraction efficiency could be obtained for a membrane of 20 µm thickness and an applied voltage of 200 V. In a flow‐through arrangement the preconcentration factor was inversely dependent on the flow rate but constant for different concentrations. The extraction of perchlorate down to 2 nM was demonstrated.     

Membrane Filtration with Liquids: A Global Approach with Prior Successes,New Developments and Unresolved Challenges

After 70 years, modern pressure‐driven polymer membrane processes with liquids are mature and accepted in many industries due to their good performance, ease of scale‐up, low energy consumption, modular compact construction, and low operating costs compared with thermal systems. Successful isothermal operation of synthetic membranes with liquids requires consideration of three critical aspects or “legs” in order of relevance: selectivity, capacity (i.e. permeation flow rate per unit area) and transport of mass and momentum comprising concentration polarization (CP) and fouling (F). Major challenges remain with respect to increasing selectivity and controlling mass transport in, to and away from membranes. Thus, prediction and control of membrane morphology and a deep understanding of the mechanism of dissolved and suspended solute transport near and in the membrane (i.e. diffusional and convective mass transport) is essential. Here, we focus on materials development to address the relatively poor selectivity of liquid membrane filtration with polymers and discuss the critical aspects of transport limitations. Machine learning could help optimize membrane structure design and transport conditions for improved membrane filtration performance.     

Highly Efficient and Selective Membrane Transport of Silver(I) Using Dibenzodiaza‐15‐Crown‐4 as a Selective Ion Carrier

A chloroform membrane system containing dibenzodiaza‐15‐crown‐4 was found to be a highly efficient and selective transport of Ag⁺ ions through a chloroform liquid membrane. In the presence of thiosulfate ion as a suitable ion stripping agent in the receiving phase, the amount of silver transported across the liquid membrane after 105 minis 95 ± 1.3%. The selectivity of Ag⁺transport from aqueous solutions containing Tl⁺, Pb²⁺, Cd²⁺, Ni²⁺, Co²⁺, K⁺, Ca²⁺, Sr²⁺, Hg²⁺, Zn²⁺, Cu²⁺was investigated. The interfering effect of Cu²⁺ ions was drastically diminished in the presence of EDTA as a proper masking agent in the source phase.     

药物甲氧苄氨嘧啶分子模板聚合物结合作用及选择性研究

采用分子自组装印迹技术合成了对甲氧苄氨嘧啶有高选择性的模板聚合物受体.通过Scatchard分析、¹HNMR和紫外光谱研究了模板聚合物的选择结合特性.结果表明,模板聚合物主要形成一类等价结合位点,通过协同氢键作用专一地结合模板底物,其离解常数为2.22×10^-4mol/L.底物的选择性结合实验表明,这种聚合物对甲氧苄氨嘧啶呈现高的选择性结合能力.     

药物甲氧苄氨嘧啶分子模板聚合物 结合作用及选择性研究

采用分子自组装印迹技术合成了对甲氧苄氨嘧啶有高选择性的模板聚合物受体.通过Scatchard分析、     

Selective Transport of Saccharides Through a Liquid Membrane Using Cyclodextrin Dimer

A new effective transport system for saccharides through a liquid membranewas constructed. The transport rate of d-ribose in the condition of theliquid membrane with cyclodextrin dimer (2) as a transporter is 2.5 timerlarger than that without the transporter, whereas the transport rate of d-ribosein the condition of the liquid membrane with cyclodextrin monomer (1) isalmost the same as that without the transporter. The transport rate of methyld-glucoside by 2 is over twice than that by 1. The transport rate of d-deoxyribose by 2 is larger than that by 1.     

水相中L-苯丙氨酸分子印迹聚合物微球的合成及其选择、吸附性能

以L-苯丙氨酸(1)为模板分子,α-甲基丙烯酸(2)为功能单体,三羟甲基丙烷丙烯酸酯(3)为交联剂,偶氮二异丁腈(AIBN)为引发剂,在水相中合成了L-苯丙氨酸的分子印迹聚合物微球(P),其形貌经SEM表征.P的最佳合成条件为:1 250 mg,AIBN 100 mg,2 0.4 mL,3 14.5 mL,搅拌速度150 r*min-1,于70 ℃反应7 h.在最佳反应条件下合成的P具有较高的饱和吸附量(Q=6.0 mg*g-1)和较好的选择性(α=2.4).     

The Removal of Zn(II) Through Calix[4]Recorcinarene Derivative Based Polymer Inclusion Membrane From Aqueous Solution

In the present work, the transport of Zn(II) metal ion from an aqueous nitrate solution of different metal ions through a polymer inclusion membrane (PIM) containing calix[4]resorcinarene derivative used as a carrier were investigated. Zn(II)metal ion showing high permeability were transported through PIMs prepared from cellulose triacetate (CTA) as a polymeric support material and 2-NPOE as a plasticizer. Total Zn(II) concentration was determined with an Atomic Absorption Spectrometer (AAS) in the acceptor phase. The prepared PIM and supported liquid membrane (SLM) were characterized by using Scanning Electron Microscopy(SEM) and Atomic Force Microscopy (AFM) techniques. The effects of membrane composition, effects of type of plasticizer in the membrane, effects of carrier concentration, and the thickness of the membranes were examined in the facilitated transport experiments of Zn(II) ion through PIM. We compared the performance of SLM experiments under the optimum conditions identified by the PIM studies. Higher permeability coefficient values for Zn(II) was found for SLM, while lower values were ascertained for PIM. The kinetic parameters which have been calculated as the constant rate (k), permeability coefficient (P), flux (J) and diffusion coefficient (D).