XAFS investigations of nitrided NbN–SiO2 sol–gel derived films

This work presents the results of the structural analysis of xNbN–(100-x)SiO₂ (x = 100, 80, 60 mol%) thin films by X-ray absorption spectroscopy (XAS). To prepare the films, thermal nitridation of sol–gel derived coatings have been performed. The resulting films have a granular structure with NbN grains distributed in the SiO₂ matrix. The size of the grains depends on the NbN/SiO₂ molar ratio. A detailed X-ray absorption fine structure (XAFS) data analysis shows that in all the samples both nitrogen and oxygen atoms are present as nearest neighbours of Nb. The intra-granular phase is an ordered NbN phase, whereas the shells around the grains are formed mainly by an oxide phase and, possibly, by other niobium nitride phases (probably with low nitrogen content). Two possible origins of the inter-granular oxide phase were considered: incomplete nitridation of Nb₂O₅ and addition of SiO₂. Both of them are connected with the sample preparation method. The obtained XAS results allowed us to correlate the thickness and stoichiometry of the films under study with the electronic structure of the Nb ions and with the local geometric structure in their environment.     

EXAFS study of the Er3+ ion coordination in SiO2–TiO2–HfO2 sol–gel films

The local order around ion-implanted Er³⁺ ions in SiO₂–TiO₂–HfO₂ thin films prepared by sol–gel, was studied by extended X-ray absorption fine structure at the Er-L_III edge. Both the first and second coordination shells of Er³⁺ were analyzed for different heat-treatments. While the first coordination shell always consisted of ～6–7 oxygen atoms at distances varying between 2.23 and 2.27 Å, the structure of the second shell was found to vary with the film composition and heat-treatment. Namely, whereas Si was found to be the only second neighbor of erbium in binary SiO₂–TiO₂ films, the addition of HfO₂ caused a preferential replacement of Si by Hf. The post-implantation thermal treatments also played a fundamental role in determining the final environment of the erbium ions.     

Superconducting properties of an NbN–SiO2 disordered system obtained by ammonolysis of NbN–SiO2 sol–gel derived coatings

Studies in superconducting properties of NbN–SiO₂ films are reported. The films were obtained through nitridation of sol–gel derived Nb₂O₅–SiO₂ coatings at 1200 °C, a process leading to the formation of disordered structures with NbN metallic grains dispersed in the insulating SiO₂ matrix. Electrical resistivity was measured with the conventional four-terminal method in the temperature range from 5 to 280 K. The samples’ superconducting properties, examined with magnetically modulated microwave absorption (MMMA), depend on the NbN/SiO₂ molar ratio and the film’s thickness.     

Optical properties of sol–gel prepared Cerium doped Lutetium and Yttrium oxyorthosilicates

The optical properties of sol–gel prepared Cerium doped Lutetium and Yttrium oxyorthosilicates are investigated in the vacuum ultraviolet energy range by means of synchrotron radiation. The excitation and emission properties are compared to commercial samples grown by Czochralski method. The sol gel polycrystals do show emission features comparable to the ones of the monocrystals but with a slightly smaller decay time. Preliminary radioluminescence measurements indicate the possibility to apply the sol gel synthesized polycrystals as scintillating materials in the low X-ray energy range.     

Investigations on sol–gel process and structural characterization of SiO2-P2O5 powders

The purpose of the study is to investigate the influence of the precursors, pH of the solution and temperature on the gelation and structure evolution of the samples from the SiO₂-P₂O₅ system. Tetraethoxysilane (TEOS) was used as precursor for SiO₂ and triethylphosphate (TEP) or phosphoric acid for P₂O₅, together with water as reagent for hydrolysis reaction and ethylic alcohol as solvent. The pH of the sols was modified by adding hydrochloric acid, in the case of TEP and by adding ammonia, in the case of H₃PO₄. The samples have been prepared starting from P₂O₅/SiO₂ = 1/10 and 1/5 molar ratio, H₂O/TEOS = 1; 2; 3 mass ratios and C₂H₅OH/TEOS = 1 mass ratio. We prepared silico-phosphate samples in the 1.5–5 pH domain and we observed that in all the cases, the lowest gelation time was found in the 3.5–4.5 pH range. We found that for the same pH value samples prepared with H₃PO₄ had a lower gelation time (few days) by comparison with the samples prepared with TEP (weeks), explainable by the low rate of the hydrolysis and condensation reactions of TEP. When the amount of water was increased, the gelation time increased in the case of samples prepared with H₃PO₄ and it was not significantly changed in the case of the samples prepared with TEP. The increasing of the solution temperature up to 40–41 °C yielded a decreasing of the gelation time (hours), especially for the samples prepared with H₃PO₄ by comparison with those prepared using TEP. In all the cases, the increased amount of water resulted in an increasing of the gelation time, even the temperature was raised. FTIR and Raman spectroscopy characterization aimed at getting information about the structural changes in the case of the samples dried in air and also for those heated at 100 °C, 300 °C, 600 °C and 900 °C. Vibration modes specific for SiOEt, SiOH, hydrogen bonds, H₂O and combined vibrations have been observed, which are in agreement with those revealed in literature data. ³¹P and ²⁹Si MAS NMR spectra gave interesting information about first surrounding of P and Si ions meaning the type and proportion of Q species and their evolution starting from the room temperature up to 900 °C.     

Structural investigations of nitrided Nb2O5 and Nb2O5–SiO2 sol–gel derived films

Sol–gel derived xNb₂O₅–(100 ? x)SiO₂ films (where x = 100, 80, 60, 50, 40, 20, 0 mol%) were nitrided at various temperatures (800 °C, 900 °C, 1000 °C, 1100 °C and 1200 °C). The structural transformations occurring in the films as a result of ammonolysis were studied using X-ray diffraction (XRD), atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). The XRD results have shown that the temperatures below 1100 °C were too low to obtain a pure NbN phase in the samples. The AFM observations indicate that the formation of the NbN phase and the size of NbN grains are related to the silica content in the layer. NbN grains become more regular and larger as the niobium content increases. The maximum grain size of about 100 nm was observed for x = 100. Preparation of the Nb₂O₅–SiO₂ sol–gel derived layers and the subsequent nitridation is a promising method of inducing crystalline NbN in amorphous matrices. It follows from the XPS results that a small amount of Nb₂O₅ remains in the films after nitridation at 1200 °C and that nitrogen reacted not only with Nb₂O₅ but also with SiO₂.     

Synthesis and characterization of amorphous aluminosilicates prepared by sol–gel to encapsulate organic dyes

We synthesized via the sol–gel process three amorphous aluminosilicates having the stoichiometry of zeolite types A, X, and Y, respectively. The aluminosilicate, so-called SX, having the chemical composition of faujasite X, proved to be amorphous in the range 298 K up to 1273 K. At the higher temperature the sample begins to crystallize as nepheline. The anionic organic dye 1,2-dihydroxyanthraquinone (Alizarine, AL) was successfully encapsulated in the aluminosilicate matrix SX. Still, 7-α-D-glucopyranosil-9,10-dihydro-3,5,6,8-tetrahydroxy-7-methyl-9, 10 dioxanthracene carboxylic acid (carminic acid, CA) could only be deposited on the matrix surface. The adsorbents and the dye impregnated matrices were characterized using several techniques: Fourier Transform Infrared (FTIR) and Diffuse Reflectance Spectroscopies used to determine the hydroxylation as well as the adsorbed species, Small Angle X-ray Scattering (SAXS) to know the shape of the heterogeneities and the fractal dimension of each sample, nitrogen physisorption to measure the specific surface area and X-ray Diffraction (XRD) to identify the crystalline compounds present in the samples. Therefore, with these complementary techniques, the structure and the morphology of the samples were obtained.     

Characterization of nanocrystalline cobalt doped TiO2 sol–gel material

Nanocrystalline 1%, 2% and 4% Cobalt-doped TiO₂ were prepared by sol–gel technique, followed by freeze-drying treatment at ?30 °C temperature for 12 h. The obtained gels were thermally treated at 200, 400, 600 and 800 °C. X-ray Powder Diffraction (XRD), Scanning Electron microscopy (SEM), Energy-dispersive X-ray spectroscopy (EDAX) were used to study its structural properties. The XRD pattern shows the coexistence of anatase phase and minor brookite phase. UV–vis Spectroscopy and Photoluminescence (PL) were used to study its optical properties. Optical band gap was calculated with the incorporation of different concentrations of cobalt. UV–visible spectroscopy shows variation in band gap for the sample treated at different temperatures for same concentration. All Cobalt doped TiO₂ nanostructures show an appearance of Red shift relative to the bulk TiO₂. The determination of magnetic properties was also carried out by Gouy balance method.     

Microstructural characteristics and crystallization of CaO–P2O5–Na2O–ZnO glass ceramics prepared by sol–gel method

Porous phosphate-based glass ceramics prepared by the sol–gel method were characterized using Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD) and differential thermal analysis (DSC). The 48CaO–45P₂O₅–2ZnO–5Na₂O glassy system can remain fully amorphous up to 550 °C. After heat treated at 650 °C, the obtained porous bodies consisted of dense struts and macropores where β-Ca₂P₂O₇ and Na₂CaP₂O₇ phases crystallized from the glass matrix. When treated at 750 °C, Ca₄P₆O₁₉ and NaZn(PO₃)₃ precipitated homogeneously as new phases among the residual glass matrix. The material was assessed by soaking samples in phosphate-based buffer solution (PBS) solution to determine the solubility and observe apatite formation.     

AES and FTIR characterization of sol–gel alumina films

In this work we obtained sol–gel alumina coatings on AISI 304 stainless steel substrates. Alumina sols were prepared by using aluminum isopropoxide (AI) as precursor, acetic acid (HOAc) as catalyst, ethanol (C₂H₅OH) or isopropanol (C₃H₈O) as solvent, and water. The as-prepared solutions were deposited on stainless steel substrates by means of the dip-coating technique. The obtained composites were characterized by Fourier transform infrared spectroscopy (FTIR) and Auger electron spectroscopy (AES). We observed that the concentration of AlO type bonds in the obtained alumina coatings depends on the solvent type used, temperature and peptization state of the sol, withdrawal speed, and number of dipping cycles. AES experiments showed that the interface formed between the alumina coating and substrate surface is in general formed by several layers of different chemical compositions.     

Electrochromic properties of nickel oxide and mixed Co/Ni oxide films prepared via sol–gel route

The Ni oxide and mixed Co/Ni oxide films were prepared by sol–gel dip coating method at optimum conditions. The XRD analysis reveals the pure and Co mixed nickel oxide films to be in amorphous state. The field emission SEM images reveal nanopore like structure for Ni oxide film and well defined grains with pores for Ni oxide films containing 5 wt.% of Co. Electrochromic properties have been studied using cyclic voltammetric (CV) and in situ spectro-electrochemical techniques. The pure and cobalt mixed (5 wt.%) Ni oxide films exhibit anodic/cathodic diffusion coefficient of 4.93 ± 0.14/3.74 ± 0.10 × 10^?10 cm²/s and 10.00 ± 0.24/7.60 ± 0.20 × 10^?10 cm²/s respectively after 300 cycles. The cobalt mixed (5 wt.%) Ni oxide films exhibit the bleached/coloured state transmission of 90.42/7.21% with a photopic constrast ratio of 12.54 and the colouration and bleaching time were 5.9 and 2.4 s respectively. The addition of cobalt beyond 5% leads to poor transparency and inhibited electrochromic switching character.     

Crystallization of amorphous silicates far from equilibrium part I: A versatile nitrate-based sol–gel synthesis of amorphous porous Ca,Mg-rich silicates

An easy-to-use, comprehensive sol–gel method is developed to produce amorphous calcium and magnesium silicates from nitrate precursors and TetraEthOxySilane (TEOS). Final products were designed to suit basic prerequisites of starting materials for experimental investigation of crystallization around the glass transition temperature range. After gelification, thermo-gravimetric methods and infrared-spectroscopy were used to follow dehydration, decarbonation and denitrification of the xerogel. A temperature of 500 °C is found to successfully remove volatiles without causing crystallization. The microstructure revealed by transmission electron microscopy (TEM) consists of 10–20 nm individual mesoparticles of 10–20 nm. Samples annealed at 500 °C were found entirely amorphous at the TEM scale. The porosity observed by TEM and characterized by nitrogen adsorption–desorption is homogeneous and varies from 4.6 to 8.5 nm as a function of the composition. Bulk analyses by ICPMS and local analyses by EDS-TEM demonstrate that the stoichiometry can be achieved and the homogeneity is confirmed at least down to 100 × 100 nm. At lower scale, irradiation by the electron beam produces a significant volatilization of Ca and Mg, which makes chemical analyses unreliable. Pros and cons of the method and special cares for specific applications are discussed. The method was also successfully used to produce a wider range of amorphous analogs having complex compositions or containing trace elements for applications in the field of mineral physics and chemistry.     

Morphological and mechanical properties of hybrid matrices of polysiloxane–polyvinyl alcohol prepared by sol–gel technique and their potential for immobilizing enzyme

Hybrid matrices of polysiloxane–polyvinyl alcohol (POS–PVA) were prepared by sol–gel technique using different concentrations of the organic component (polyvinyl alcohol, PVA) in the synthesis medium. The goal was to prepare carriers for immobilizing enzyme by taking into consideration properties as hardness, mean pore diameter, specific surface area and pore size distribution. The matrices were activated with sodium metaperiodate to render functional groups for binding the lipase from Candida rugosa, used here as a study model. Results showed that low proportion of PVA gave POS–PVA with low surface area and pore volume, although with higher hardness. The chemical activation decreased the pore volume and increased the pore size with a decrease on the surface area of about 60–75%. The matrices for enzyme immobilization were chosen considering the best combination of high surface area and hardness. Thus, the POS–PVA prepared with 5.56 × 10^?5 M of PVA with a surface area of 123 m²/g and hardness of 71 HV (50 gf 30 s) was shown to be suitable to immobilize the lipase, with an immobilization yield of about 40%.     

Structure and electrical properties of nitrided NbN–TiN sol–gel derived films

The results of investigations of electrical conductivity and the structure of NbN–TiN thin films in a different NbN/TiN molar ratio are presented in this work. Sol–gel derived xNb₂O₅?(100?x)TiO₂ coatings (where x = 100, 90, 80, 70, 60, 50, 40, 0 mol%) were nitrided at 1200 °C to obtain NbN–TiN films. The structural transformations occurring in the films as a result of ammonolysis were studied using X-ray diffraction (XRD), atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). The electrical conductivity was measured with a conventional four-terminal method in the temperature range of 5–280 K. The NbN–TiN samples exhibited a negative temperature coefficient of resistivity. The positive temperature coefficient of resistivity was observed only for the x = 0 sample. The results of conductivity versus temperature may be described on the grounds of a model proposed for a weakly disordered system. The film thickness effect on the superconducting properties was studied for x = 80 and x = 100 samples. The superconducting transition was not observed in all samples, the exception was x = 80 sample, 1050 nm in thickness. It is not clear, why all x = 100 samples do not exhibit superconducting transition in resistivity measurements. It seems to be possible, that the Josephson junction formation between NbN grains could be blocked by non-superconducting phases present in these samples.     

Effect of reducing sintering atmosphere on Ce-doped sol–gel silica glasses

The effect of sintering atmosphere on the optical and structural properties of Cerium doped sol–gel silica was investigated. Two sets of xerogels with Ce concentration from 0 to 10 mol% were prepared and densified in different conditions. The effect of a post-densification rapid thermal treatment was also considered. Optical absorption measurements evidenced that in oxidizing conditions Cerium is preferably incorporated inside the silica matrix as Ce⁴⁺ while the trivalent state is favoured by reducing conditions. Transmission electron microscopy images show rare-earth clusters formation whose nature was investigated by means of Raman, EDS and microdiffraction measurements. In order to evaluate the efficiency of the glasses as scintillating materials radio-luminescence measurements were carried out. A numerical fit of RL spectra showed the presence of two components peaking at 2.7 and 3.1 eV. After RTT, the relative intensity of the 3.1 eV component increases with Ce concentration.     

Optimization of sol–gel/pyrolysis routes to silicon oxycarbide glasses

The optimization of the synthesis of silicon oxycarbide ceramics via the sol–gel/pyrolysis route is described, starting from several alkylalkoxysilanes and vinylalkoxysilanes. The main aim was to achieve low weight losses during cure and pyrolysis and also a compact ceramics morphology. The theoretical composition of the pyrolysates was changed between SiO_1.5C and SiO_1.2C_2.3, by varying monomer types and ratios. An assessment of the real composition was performed using energy-dispersive X-ray spectroscopy. The smallest weight losses were obtained for the resins based on vinyltriethoxysilane and dimethyldiethoxysilane which were additionally modified by the addition of a small amount of boric acid. Somewhat higher weight losses combined with the best toughness were found for resins based on non-vinylated silsesquioxane with a low content on linear dimethylsiloxane units. As an alternative, a precursor (SiO_0.9C_2.8) was prepared via hydrosilylation, based on cyclic dimethylsiloxane oligomers interconnected to a network, but its weight losses were higher than those of sol–gel silicon oxycarbide.     

Magnetite nanoparticles prepared by the crystallization of Na2O–Fe2O3–B2O3–SiO2 glasses

A glass with the composition of 35Na₂O–24Fe₂O₃–20B₂O₃–20SiO₂–1ZnO (mol%) was melted, quenched, using a twin roller technique, and subsequently heat treated in the range 485–750 °C for 1–2 h. This led to the crystallization of magnetite as the sole or the major crystalline phase.Heat treatment at lower temperatures resulted in the crystallization of magnetite crystals 7–20 nm in diameter, whereas heat treatment at higher temperatures produced higher quantities of magnetite and much larger crystals. The room temperature magnetization and coercive force values were in the range of 6–57 emu g^? 1 and 0–120 Oe, respectively for the heat treated glasses.     

Correlation between the method of preparation and the properties of the sol–gel HfO2 thin films

This work describes the preparation of HfO₂ thin films by the sol–gel method, starting with different precursors such as hafnium ethoxide, hafnium 2,4-pentadionate and hafnium chloride. From the solution prepared as mentioned above, thin films on silicon wafer substrates have been realized by ‘dip-coating’ with a pulling out speed of 5 cm min^?1. The films densification was achieved by thermal treatment for 10 min at 100 °C and 30 min at 450 °C or 600 °C, with a heating rate of 1 °C min^?1. The structural and optical properties of the films are determined employing spectroellipsometric (SE) measurements in the visible range (0.4–0.7 μm), transmission electron microscopy (TEM) and high-resolution transmission electron microscopy (HRTEM). The main objective of this paper was to establish a correlation between the method of preparation (precursor, annealing temperature) and the properties of the obtained films. The samples prepared from pentadionate and ethoxide precursors are homogenous and uniform in thickness. The samples prepared starting from chloride precursor are thicker and proved to be less uniform in thickness. Higher non-uniformity develops in multi-deposition films or in crystallized films. A nano-porosity is present in the quasi-amorphous films as well in the crystallized one. For the samples deposited on silicon wafer, the thermal treatment induced the formation of a SiO₂ layer at the coating–substrate interface.     

Raman and NMR study of bioactive Na2O–MgO–CaO–P2O5–SiO2 glasses

The results of a structural study combining NMR and Raman spectroscopy of several melt-derived glasses in the system Na₂O–MgO–CaO–P₂O₅–SiO₂ are presented. The Raman spectra show clear changes in the Si–O–Si vibrational modes (related to the bridging oxygen atoms, BO) and also verify the presence of non-bridging oxygen atoms (NBO), also named terminal oxygens. The intensity of the Si–O–NBO stretching mode depends on the cation concentration. It can be concluded from the NMR studies that the MgO-containing samples have orthophosphate units charge-compensated by Ca²⁺ and Mg²⁺. The silicate matrix also contains both types of two-valent cations and consists of Q² and Q¹ units. Similarly, the Na₂O-containing samples contain isolated orthophosphate units in a silicate matrix (Q² and Q³ units), both charge-compensated by mixed cations Ca²⁺ and Na⁺. These experimental data were compared with theoretical parameters given by the Stevels model, which is a suitable tool for understanding bioactive behavior of these glasses. Furthermore, results of the in vitro tests carried out in simulated body fluids are presented and compared with both Raman and NMR structural data.