Use of multi-coil parallel-gap resonators for co-registration EPR/NMR imaging

This article reports experimental investigations on the use of RF resonators for continuous-wave electron paramagnetic resonance (cw-EPR) and proton nuclear magnetic resonance (NMR) imaging. We developed a composite resonator system with multi-coil parallel-gap resonators for co-registration EPR/NMR imaging. The resonance frequencies of each resonator were 21.8MHz for NMR and 670MHz for EPR. A smaller resonator (22mm in diameter) for use in EPR was placed coaxially in a larger resonator (40mm in diameter) for use in NMR. RF magnetic fields in the composite resonator system were visualized by measuring a homogeneous 4-hydroxy-2,2,6,6-tetramethyl-piperidinooxy (4-hydroxy-TEMPO) solution in a test tube. A phantom of five tubes containing distilled water and 4-hydroxy-TEMPO solution was also measured to demonstrate the potential usefulness of this composite resonator system in biomedical science. An image of unpaired electrons was obtained for 4-hydroxy-TEMPO in three tubes, and was successfully mapped on the proton image for five tubes. Technical problems in the implementation of a composite resonator system are discussed with regard to co-registration EPR/NMR imaging for animal experiments.     

Combining a Magnetic Field Modulation Coil with a Surface-Coil-Type EPR Resonator

It is thought that the design of magnetic field modulation coils is one of the factors limiting enlargement of the sample size in electron paramagnetic resonance (EPR) measurements. In this study, we miniaturized the magnetic field modulation coil and combined it with a surface-coil-type resonator (SCR). The inductor of the SCR was a circular single-turn one-loop coil (diameter, 1 mm), and the magnetic field modulation coil was a twin-loop coil consisting of two solenoid coils each made of 15 turns of copper wire on a cylindrical bobbin with an axial length of 3 mm and an elliptical cross section (major axis, 7 mm; minor axis, 3 mm). The former was located on the latter via a spacer (thickness, 3 mm) in such a way that the directions of their axes coincided. Their combined size was about 10 mm wide, 10 mm deep, and 6 mm high. The transmission lines of the SCR were set on resonance at about 700 MHz. EPR measurements of a phantom (comprising agar that included a nitroxide radical and physiological saline solution), made with a miniaturized modulation coil combined with the SCR, exhibited a sensitivity similar to that for the conventional method. Authors' address: Hidekatsu Yokoyama, Department of Pharmaceutical Sciences, International University of Health and Welfare, 2600-1 Kitakanemaru, Ohtawara 324-8501, Japan     

Single loop multi-gap resonator for whole body EPR imaging of mice at 1.2 GHz

For whole body EPR imaging of small animals, typically low frequencies of 250-750 MHz have been used due to the microwave losses at higher frequencies and the challenges in designing suitable resonators to accommodate these large lossy samples. However, low microwave frequency limits the obtainable sensitivity. L-band frequencies can provide higher sensitivity, and have been commonly used for localized in vivo EPR spectroscopy. Therefore, it would be highly desirable to develop an L-band microwave resonator suitable for in vivo whole body EPR imaging of small animals such as living mice. A 1.2 GHz 16-gap resonator with inner diameter of 42 mm and 48 mm length was designed and constructed for whole body EPR imaging of small animals. The resonator has good field homogeneity and stability to animal-induced motional noise. Resonator stability was achieved with electrical and mechanical design utilizing a fixed position double coupling loop of novel geometry, thus minimizing the number of moving parts. Using this resonator, high quality EPR images of lossy phantoms and living mice were obtained. This design provides good sensitivity, ease of sample access, excellent stability and uniform B(1) field homogeneity for in vivo whole body EPR imaging of mice at 1.2 GHz.     

Influence of the lens effect in a sample with large dielectric constant in a loop-gap resonator on the EPR signal intensity at 700 MHz

The influence of the lens effect on the electron paramagnetic resonance (EPR) signal intensity was investigated in a loop-gap resonator (LGR) with an inner diameter of 41 mm. TheQ- value and EPR signal intensity were measured when the phantoms containing 3-carbamoyl-2,2,5,5-tetramethyl-pyrrolidin-l-yloxy dissolved in sodium chloride aqueous solutions were put in the LGR. TheQ- value and signal intensity reduced with increasing concentrations of sodium chloride in the phantom, indicating that the imaginary part of the dielectric constant is larger in the phantom with the higher concentration of sodium chloride. However, relationships betweenQ-values of the resonator and EPR signal intensities were not proportional and signal intensities were relatively higher compared with theQ-values. These findings suggest that the signal reduction due to lowQ is slightly compensated by the lens effect in the sample with the large real part of the dielectric constant. In the distribution of the signal intensities of a pinpoint sample made of diphenylpicrylhydrazyl in the agar medium containing sodium chloride in the LGR, it was found that the signal intensity decreased according to the distance from the center and the difference in the signal intensity within 10 mm from the center was about 20%, indicating the inhomogeneity of the alternating magnetic field at the center and marginal region in the sample with the large dielectric constant caused by the lens effect.     

Pulsed near-infrared laser diode excitation system for biomedical photoacoustic imaging

A pulsed laser diode system operating at 905 nm has been developed for the generation of photoacoustic signals in tissue. It was evaluated by measuring the photoacoustic waveforms generated in a blood vessel phantom comprising three dye-filled (mu(a)=1 mm(-1)) tubes of diameters 120-580 microm immersed to a maximum depth of 9 mm in a turbid liquid (mu'(s)=1 mm(-1)). The system was then combined with a cylindrical scanning system to obtain two-dimensional images of a tissue phantom. The signal-to-noise ratio of the detected signals in both cases and the image contrast in the latter suggest that such a system could provide a compact and inexpensive alternative to current excitation sources for superficial imaging applications.     

Modified surface-coil-type resonators for EPR measurements of a thin membranelike sample

Surface-coil-type resonators (SCRs) equipped with a circular single-tum coil (conventional SCR), a circular spiral coil (spiral SCR), and a plate-type single-turn coil (plate-type SCR) were fabricated. By using these SCRs, the electron paramagnetic resonance (EPR) sensitivities of thin membranelike samples were investigated. For a non-dielectric-loss phantom, filter paper containing 1,1-diphenyl-2-picrylhydrazyl was used. For a high-dielectric-loss phantom, gauze containing an aqueous solution of 3-carbamoyl-2,2,5,5-tetramethylpyrrolidine-1-oxyl (carbamoyl-PROXYL) was used. For a biological sample, a pea leaf impregnated with the carbamoyl-PROXYL solution was used. The sensitivity (signal-to-noise ratio) of the spiral and plate-type SCRs for the non-dielectric-loss phantom was significantly greater than that of the conventional SCR. Under these conditions, the sensitivity of the spiral SCR was relatively higher than that of the plate-type SCR. For the high-dielectric-loss phantom, the sensitivity of the plate-type SCRs was significantly greater than that of the conventional SCR, but there were no differences in sensitivity between the spiral and conventional SCRs. The sensitivity of the plate-type SCR in the EPR measurement of a pea leaf was significantly greater than that of the conventional SCR. These findings show that the spiral and plate-type SCRs are suitable for measuring EPR of thin membranelike samples, especially when the former is used for the non-dielectric-loss sample and the latter for high-dielectric-loss sample, including the leaf.     

Construction and performance of an NMR tube with a sample cavity formed within magnetic susceptibility-matched glass

We describe the construction and performance of an NMR tube with a magnetic susceptibility matched sample cavity that confines the solution within the detection zone in the axial direction and in a quasi-rectangular region in the radial direction. The slot-like sample cavity provides both good sample volume efficiency and tolerance to sensitivity loss in the sample space. The signal-to-noise ratio per unit volume of the constructed tube was 2.2 times higher than that of a cylindrical tube of 5mm outer diameter with a sample containing 300 mM NaCl at a static magnetic field of 14.1T. Even the overall signal-to-noise ratio of the slot tube was 35% higher than that of the conventional 5mm tube for a sample containing 300 mM NaCl. Similar improvements over existing sample tube geometries were obtained at 950 MHz. Moreover the temperature rise resulting from RF heating was found to be significantly lower for the slot tube even when compared to 3 and 4mm outer diameter cylindrical tubes as measured in a 5mm cryoprobe. A further advantage of this type of tube is that a sample cavity of any desired size and shape can be formed within a cylindrical tube for use in a single cryogenic probe.     

Twin LC Resonator System for EPR Measurements Operating at Radio-Frequency

Two LC resonant circuits resonating at the same frequency (245 MHz) faced each other with reverse polarity (twin electron paramagnetic resonance (EPR) resonator). For the inductor of the LC circuit, a square single-turn one-loop coil (width, 38 mm) was fabricated. Each LC circuit was independently tuned using mechanical variable capacitors. A cylindrical phantom (diameter, 25 mm) including a 1 mM nitroxide radical physiological saline solution was located at the center of two coils (distance between these coils, 50 mm). Two resonant frequencies (the lower and the higher ones) were observed at each LC circuit of the twin EPR resonator with termination of the other LC circuit. The lower resonant frequency alone was observed when the powers from two LC circuits of the twin EPR resonator were combined by a 180° combiner. On the other hand, the higher frequency alone was observed when they were combined by a 0° combiner. EPR signals could be obtained using the 180° combiner (lower frequency) but not the 0° combiner (higher frequency).     

Determination of absolute concentration of nitroxide radical by radio-frequency EPR imaging

The absolute concentrations of a nitroxide radical in samples in a loop-gap resonator (LGR) were determined by using a radio-frequency (about 720 MHz) electron paramagnetic resonance (EPR) imaging system. EPR imaging of phantoms containing a nitroxide radical, 3-carbamoyl-2,2,5,5-tetramethylpyrrolidin-1-yloxy (carbamoyl-PROXYL), dissolved in various concentrations of an aqueous sodium chloride solution was made to investigate the influence of dielectric losses and sample position within the LGR. As it was found that these influences on the signal intensity were sufficiently small (less than 6%), it is possible to use identical radical solutions in which the radical is dissolved in a known concentration as an internal marker. Two phantoms containing aqueous solutions of 3 mM (as a marker) and 1, 2, 3, 4, or 5 mM (as a sample) carbamoyl-PROXYL were placed together in the LGR. From EPR images of these phantoms, the absolute concentration of the sample could be calculated by using the gray-scale value (i.e., the signal intensity) of the marker and sample within a small margin of error (about 4%).     

Estimation of the in vivo decay rate of EPR signals for a nitroxide radical in rat brains by a region-selected intensity determination method

The region-selected intensity determination (RSID) method was proposed to obtain the temporal changes in electron paramagnetic resonance (EPR) signal intensity from a selected region by a stationary magnetic field gradient. To select the region, the subtraction field that was derived from the distance between the center and the projection of the selected region to the direction of the field gradient was applied to the main field. The directions of the stationary magnetic field gradient at a constant strength were systematically changed in a three-dimensional space after each acquisition of the spectrum. All spectra under the field gradient were accumulated and the resultant spectrum was deconvoluted by a spectrum without the field gradient. The center height of the deconvoluted spectrum indicates the signal intensity of the selected region. To verify this method, a phantom or in vivo study was conducted on a 700 MHz radio-frequency EPR spectrometer equipped with a bridged loop-gap resonator. In the temporal EPR measurements of phantoms including a nitroxide radical aqueous solution with and without ascorbic acid, the selected regions were alternatively changed at the position of the two phantoms. The signal intensity derived from the one phantom showed an exponential decay, and for the other phantom, no temporal changes. The spatial resolution of this method was estimated to be 2.7 mm by using a pinpoint phantom that included diphenylpicrylhydrazyl powder. In the in vivo temporal EPR measurements, the selected regions were alternatively changed at the cerebral cortex and the striatum of rats that had received a blood-brain barrier-permeative nitroxide radical. The decay rate of the signal intensity at each region obtained by this method was consistent with those previously reported.     

Accelerated electron paramagnetic resonance imaging using partial Fourier compressed sensing reconstruction

PurposeElectron paramagnetic resonance (EPR) imaging has evolved as a promising tool to provide non-invasive assessment of tissue oxygenation levels. Due to the extremely short T₂ relaxation time of electrons, single point imaging (SPI) is used in EPRI, limiting achievable spatial and temporal resolution. This presents a problem when attempting to measure changes in hypoxic state. In order to capture oxygen variation in hypoxic tissues and localize cycling hypoxia regions, an accelerated EPRI imaging method with minimal loss of information is needed.MethodsWe present an image acceleration technique, partial Fourier compressed sensing (PFCS), that combines compressed sensing (CS) and partial Fourier reconstruction. PFCS augments the original CS equation using conjugate symmetry information for missing measurements. To further improve image quality in order to reconstruct low-resolution EPRI images, a projection onto convex sets (POCS)-based phase map and a spherical-sampling mask are used in the reconstruction process. The PFCS technique was used in phantoms and in vivo SCC7 tumor mice to evaluate image quality and accuracy in estimating O₂ concentration.ResultsIn both phantom and in vivo experiments, PFCS demonstrated the ability to reconstruct images more accurately with at least a 4-fold acceleration compared to traditional CS. Meanwhile, PFCS is able to better preserve the distinct spatial pattern in a phantom with a spatial resolution of 0.6 mm. On phantoms containing Oxo63 solution with different oxygen concentrations, PFCS reconstructed linewidth maps that were discriminative of different O₂ concentrations. Moreover, PFCS reconstruction of partially sampled data provided a better discrimination of hypoxic and oxygenated regions in a leg tumor compared to traditional CS reconstructed images.ConclusionsEPR images with an acceleration factor of four are feasible using PFCS with reasonable assessment of tissue oxygenation. The technique can greatly enhance EPR applications and improve our understanding cycling hypoxia. Moreover this technique can be easily extended to various MRI applications.     

Transverse oriented electric field re-entrant resonator (TERR) with automatic tuning and coupling control for EPR spectroscopy and imaging of the beating heart

Sample motion, particularly that of a beating heart, induces baseline noise and spectral distortion on an EPR spectrum. In order to quench motional noise and restore the EPR signal amplitude and line-width, an L-band transverse oriented electric field re-entrant resonator (TERR) was designed and constructed with provisions for automatic tuning control (ATC) and automatic coupling control (ACC) suited for studies of isolated beating rat hearts. Two sets of electronic circuits providing DC biased voltage to two varactor diodes were implemented to electronically adjust coupling and tuning. The resonator has a rectangular cross-sectional sample arm of 25 mm diameter with a Q value of 1100 without sample. Once inserted with lossy aqueous samples of 0.45% NaCl, Q value drops to 400 with a volume of 0.5 ml and 150 with 5 ml. The ATC/ACC functions were tested with a moving phantom and isolated beating rat hearts with the improvement of signal to noise ratio (S/N, peak amplitude of signal over peak amplitude of baseline noise) of 6.7-, and 4 to 6-fold, respectively. With these improvements, EPR imaging could be performed on an isolated beating rat heart. Thus, this TERR resonator with ATC/ACC enables application of EPR spectroscopy and imaging for the measurement and imaging of radical metabolism, redox state, and oxygenation in the isolated beating rat heart.     

Influence of the movement of cylindrical samples with variable internal diameter and variable length along thex-axis of a double TE104 and a single TE102 rectangular cavity on the EPR signal intensity: A sample shape study

The response of the cavity to the movement of cylindrical samples with internal diameters from 0.7 to 4 mm and lengths from 5 to 50 mm along thex-axis of the Bruker double TE₁₀₄ and single TE₁₀₂ rectangular cavity has been analyzed. Independently of sample internal diameter, the experimentally observed dependences of the electron paramagnetic resonance (EPR) signal intensity versus sample position in the cavity showed the following: (i) a sharp maximum for sample lengths from 5 to 20 mm; (ii) a “plateau”, over which the signal intensity remained constant within experimental errors of 0.47–1.16%, for lengths from 30 to 40 mm; and (iii) a “sloping plateau” region, which could be approximated by the linear function (correlationr = 0.96–0.98) for the 50 mm sample. Theoretical predictions of the experimental dependences of the signal intensity versus sample position in the cavity were calculated with the “modified” and “revised” sine-squared function, and the correlation between observed and theoretically computed dependences is very good. Additionally, the experimental dependence of the signal intensity versus the sample internal diameter and length for cylindrical samples situated at the position in the cavity at which the signal intensity was a maximum was likewise numerically approximated by the surface fitting with the Lorentzian cumulative additive function (correlationr = 0.999). The experimental dependence of the signal intensity versus the sample internal diameter for the given sample length is nonlinear. The samples with internal diameters of 0.7 and 1 mm gave the total maximum of signal intensity for the 40 mm sample, however, the samples with internal diameters of 2, 3 and 4 mm gave the total maximal value of signal intensity, which was identical for both the 30 and 40 mm samples. The experimental dependence of the EPR signal intensity versus the sample volume clearly showed that the samples with identical volumes, however, with different shapes, can give significantly different signal intensities (with differences ca. 200–400%). Then, the comparison of cylindrical samples with identical volumes but different shapes may be a serious source of significant errors in quantitative EPR spectroscopy. Cylindrical samples to be compared should be of identical shape. Accurate and precise positioning of each sample in the microwave cavity is essential.     

Determination of differential quantum yields in solution by electron paramagnetic resonance spectroscopy

Quantitative kinetic studies on the photochemistry of paramagnetic species in solution may be carried out by electron paramagnetic resonance (EPR) spectroscopy. A cylindrical cell can be used as photochemical reactor, but the internal diameter should be less than 1.7 mm in order to achieve the resonance of an aqueous sample in an X-band (9–10 GHz) spectrometer. In this paper we present a detailed analysis of the fractions of incident light that are reflected, transmitted and absorbed by a liquid solution in a quartz cylindrical cell placed in the optical cavity of an X-band EPR spectrometer. Since the photolysis cell is irradiated perpendicularly to its axis, variable angles of incidence have been considered to calculate the transmission and reflection coefficients from Fresnel equations. Polarization of light has been also taken into account in the evaluation of the coefficients. The procedure proposed here is adequate for the evaluation of the absorbed light in the determination of quantum yields. The continuous photolysis at 366 nm of symmetric chlorine dioxide (OCIO) in aqueous solution was considered as an example. The initial differential quantum yield obtained for OCIO photodecomposition in aqueous solution was Θ₃₆₆ = 0.55 ± 0.04.     

A tunable general purpose Q-band resonator for CW and pulse EPR/ENDOR experiments with large sample access and optical excitation

We describe a frequency tunable Q-band cavity (34 GHz) designed for CW and pulse Electron Paramagnetic Resonance (EPR) as well as Electron Nuclear Double Resonance (ENDOR) and Electron Electron Double Resonance (ELDOR) experiments. The TE(011) cylindrical resonator is machined either from brass or from graphite (which is subsequently gold plated), to improve the penetration of the 100 kHz field modulation signal. The (self-supporting) ENDOR coil consists of four 0.8mm silver posts at 2.67 mm distance from the cavity center axis, penetrating through the plunger heads. It is very robust and immune to mechanical vibrations. The coil is electrically shielded to enable CW ENDOR experiments with high RF power (500 W). The top plunger of the cavity is movable and allows a frequency tuning of ±2 GHz. In our setup the standard operation frequency is 34.0 GHz. The microwaves are coupled into the resonator through an iris in the cylinder wall and matching is accomplished by a sliding short in the coupling waveguide. Optical excitation of the sample is enabled through slits in the cavity wall (transmission ～60%). The resonator accepts 3mm o.d. sample tubes. This leads to a favorable sensitivity especially for pulse EPR experiments of low concentration biological samples. The probehead dimensions are compatible with that of Bruker flexline Q-band resonators and it fits perfectly into an Oxford CF935 Helium flow cryostat (4-300 K). It is demonstrated that, due to the relatively large active sample volume (20-30 μl), the described resonator has superior concentration sensitivity as compared to commercial pulse Q-band resonators. The quality factor (Q(L)) of the resonator can be varied between 2600 (critical coupling) and 1300 (over-coupling). The shortest achieved π/2-pulse durations are 20 ns using a 3 W microwave amplifier. ENDOR (RF) π-pulses of 20 μs ((1)H @ 51 MHz) were obtained for a 300 W amplifier and 7 μs using a 2500 W amplifier. Selected applications of the resonator are presented.     

A rotating phantom for the study of flow effects in MR imaging

A common type of phantom used for the study of flow effects in MR imaging is the tube phantom, where a liquid passes through a set of tubes placed in the main magnetic field of an MR scanner. Among the disadvantages with this type of phantom are that a distribution of velocities is present in each tube, and that quantifications of flow effects using tube phantoms may be very time-consuming. In this work, we describe the design and the properties of a rotating wheel flow phantom used for quantification of the effects of flow through the imaging plane as well as in the imaging plane. The proposed phantom is constructed as a rotating gel-filled wheel, surrounded by static volumes filled with the same gel, and the evaluation of the information from rotating and static parts is made with a specially designed computer program. The phantom can be used as a plug flow phantom covering simultaneously an interchangeable velocity interval, which at present has the range −52 mm/s, +52 mm/s. It is shown that the phantom gives adequate information on the dependence of pixel content on first-order motion in MR modulus and phase images. Among the fields of application are rapid calibration of MR imaging units for flow determination using phase information, as well as testing of pulse sequence characteristics and verification of theoretical predictions concerning the flow dependence in MR images.     

Analysis of the Movement of Line-like Samples of Variable Length along theX-Axis of a Double TE104and a Single TE102Rectangular Cavity

Movement of line-like samples with lengths from 5 to 50 mm along thex-axis of the double TE₁₀₄rectangular cavity has been analyzed. The observed dependencies of the EPR signal intensity versus sample position showed: (i) a sharp maximum for sample lengths from 5 to 20 mm; (ii) a plateau, over which the EPR signal intensity remained constant within experimental errors of 0.26–1.07%, for lengths from 30 to 40 mm; and (iii) a “sloping plateau,” which could be approximated by the linear function (correlation,r= 0.98) for sample length 50 mm. Theoretical values of the experimentally observed dependencies of the intensity versus sample position were calculated using the modified sine-squared function and the correlation between observed and theoretically predicted dependencies is very good. The experimental dependence of the EPR signal intensity versus the sample length for samples situated at the same point in the cavity was nonlinear with a maximum for the 40-mm sample. The dependence of the EPR signal intensity upon the movement of a large cylindrical sample (o.d. 4 mm and length 100 mm) along thex-axis of the cavity was similar to that found for the 50-mm sample. However, an additional oscillating signal superimposed on the sloping plateau was observed. The presence of a large sample fixed in the complementary cavity of the double TE₁₀₄cavity caused an additional deformation of the signal intensity for a 30-mm sample which was moving in the first cavity. The primary effect was that the plateau was replaced by a region in which the intensity increased linearly with sample position,r= 0.99. Each of the above phenomena may be a source of significant errors in quantitative EPR spectroscopy. Cylindrical samples to be compared should be of identical length and internal diameter. Accurate and precise positioning of each sample in the microwave cavity is essential.     

Thermographic visualization of the superficial vein and extravasation using the temperature gradient produced by the injected materials

There are few effective methods to detect or prevent the extravasation of injected materials such as chemotherapeutic agents and radiographic contrast materials. To investigate whether a thermographic camera could visualize the superficial vein and extravasation using the temperature gradient produced by the injected materials, an infrared thermographic camera with a high resolution of 0.04 °C was used. At the room temperature of 26 °C, thermal images and the time course of the temperature changes of a paraffin phantom embedded with rubber tubes (diameter 3.2 mm, wall thickness 0.8 mm) were evaluated after the tubes were filled with water at 15 °C or 25 °C. The rubber tubes were embedded at depths of 0 mm, 1.5 mm, and 3.0 mm from the surface of the phantom. Temperature changes were visualized in the areas of the phantom where the tubes were embedded. In general, changes were more clearly detected when greater temperature differences between the phantom and the water and shallower tube locations were employed. The temperature changes of the surface of a volunteer’s arm were also examined after a bolus injection of physiological saline into the dorsal hand vein or the subcutaneous space. The injection of 5 ml room-temperature (26 °C) saline into the dorsal hand vein enabled the visualization of the vein. When 3 ml of room-temperature saline was injected through the vein into the subcutaneous space, extravasation was detected without any visualization of the vein. The subtraction image before and after the injection clearly showed the temperature changes induced by the saline. Thermography may thus be useful as a monitoring system to detect extravasation of the injected materials.     

High-field/high-frequency EPR spectrometer operating in pulsed and continuous-wave mode at 180 GHz

A novel electron paramagnetic resonance (EPR) spectrometer is reported, which has been developed to allow pulsed EPR experiments with high sensitivity and time resolution at a microwave (MW) frequency of 180 GHz (G-band) and wavelengths of approximately 1.6 mm. This corresponds to a magnetic field of about 6.4 T forg ≈ 2 signals. The “hybrid” system architecture combines components of quasioptical as well as conventional MW techniques, making it possible to achieve excellent spectrometer performance with respect to sensitivity and time resolution. Quasioptical MW components have been used to design an MW circulator allowing high sensitivity and low bias operation in the reflection mode. A miniaturized, closed-type cylindrical cavity provides a high sample filling factor and an adequate MW field strength (B₁) enhancement and thus permits reasonably short MW pulses (60 ns for a π/2 pulse) even with a moderate MW input power (15 mW at the cavity). Commercial quartz capillaries (up to 0.5 mm internal diameter) can be used as sample holders for a broad range of applications.     

Biochemical EPR imaging of skin

EPR Imaging (EPRI) of spin labels is a powerful method for investigating skin and can give information about biochemical processes which are involved in numerous skin diseases. Furthermore it enables the non invasive investigation of the liberation, penetration and distribution of spin labelled drugs. The basis of these measurements is spectral spatial EPR imaging employing modulated field gradients and simultaneous field scans (MOSS). A skin region (?=6 mm) was treated with a 10 μl spin label solution (1 mM). EPR spectra of 128 points were recorded in 128 spatial planes resulting in a 128×128 image matrix. A spatial resolution of better than 10 μm can be obtained for a spectral line width of 0.1 mT and a gradient of 4 Tm^?1.In vivo imaging on mammalian skin can be performed by employing surface coils at S-band frequencies, 3 GHz.