Synthesis of calcium titanate from [Ca(H2O)3]2[Ti2(O2)2O(NC6H6O6)2]·2H2O as a cheap single-source precursor

Calcium titanate (CaTiO₃) was conveniently synthesized by thermal decomposition of a single-source precursor [Ca(H₂O)₃]₂[Ti₂(O₂)₂O(NC₆H₆O₆)₂]·2H₂O at low temperature. This single-source precursor was characterized by elemental analysis, IR spectrum, thermal gravimetric analysis and X-ray single crystal diffraction. The calcined products at different temperature were further characterized by powder X-ray diffractions and IR spectra. The morphology, microstructure, and crystallinity of the resulting CaTiO₃ materials have been characterized by SEM and TEM. The BET measurement revealed that the CaTiO₃ powders had a surface area of 14.0 m²/g. In addition, the microwave dielectric properties of the resulting CaTiO₃ material have been measured.     

Separation of 99Mo from a simulated fission product solution by precipitation with a-benzoinoxime

The formation property of Mo precipitate was investigated and improved the existing process was using H₂O₂ that acts as an interfering compound in a subsequent alumina adsorption process. The property of the Mo precipitate was investigated by using SEM, FTIR, TG-DTA, and XRD. The simulated solution consisted of 1M nitric acid containing seven elements (Mo, I, Ru, Zr, Ce, Nd, Sr) and their radioactive tracers. As a result, the precipitate was composed of the Mo precipitate and re-precipitated a-benzoinoxime which was added excessively for increasing the precipitation efficiency. It was confirmed that the Mo precipitate was formed by the reaction of two a-benzoinoxime molecules and one MoO₂ ²⁺. Molybdenum precipitate was dissolved in 0.4M NaOH solution within 5 minutes without H₂O₂. Hydrogen peroxide induced only the rapid dissolution of the a-benzoinoxime re-precipitate. Also, the dissolution method without H₂O₂ was favorable in the purification aspect because Zr and Ru were contained as a small fraction of 1.3% and 7.7%, respectively, in the dissolving solution.     

Phase evolution of lead titanate from its amorphous precursor synthesized by the OPM wet-chemical route

Lead titanate was synthesized by the OPM wet-chemical route by the dissolution of Ti metal in H₂O₂ followed by the addition of Pb²⁺ at high pH, resulting in a reactive and amorphous precipitate with (Pb:Ti=1:1) mole ratio, which was heat treated between 400°C and 700°C. The amorphous precipitate was characterized by DSC, and all of the powders were characterized by X-ray diffraction, Raman and XAS (EXAFS and XANES) spectroscopy at the Ti K edge. A metastable, stoichiometric and cubic pyrochlore phase (Pb₂Ti₂O₆, Fd3m) was identified by XRD and Raman spectroscopy up to approx. 450°C. Only tetragonal PbTiO₃ was identified at higher temperatures. XAS spectra showed that the local structure around the absorbing Ti atom of the intermediate pyrochlore phase is similar to that observed in the amorphous precursor. This fact indicates that the metastable intermediate pyrochlore (Pb₂Ti₂O₆) is kinetically favored to be formed because of its similarity to the amorphous precipitate, instead of the slightly different and thermodynamically favored tetragonal (PbTiO₃, P4/mmm) perovskite structure that is only formed at higher temperatures, after the crystallization of the metastable intermediate pyrochlore.     

Phase evolution of a barium tin 1,2-ethanediolato complex to barium stannate during thermal decomposition

The thermal behaviour of [Ba(C₂H₆O₂)₄][Sn(C₂H₄O₂)₃] used as a BaSnO₃ precursor, and its phase evolution during thermal decomposition are described. The initially formed transient barium tin oxycarbonate phase disintegrates into BaCO₃ and SnO₂, reacting subsequently to BaSnO₃. The existence of the intermediate oxycarbonate phase is evidenced by Fourier transformed infrared (FT-IR), X-ray powder diffraction (XRD) and electron energy loss spectroscopy (EELS (ELNES)) investigations.     

The electrical properties of chemically obtained barium titanate improved by attrition milling

Barium titanate ceramics were prepared using the nanopowder resulting from a polymeric precursor method, a type of modified Pechini process. The obtained nanopowder was observed to agglomerate and in order to de-agglomerate the powder and enhance the properties of the barium titanate the material was attrition milled. The impact of this attrition milling on the electrical properties of the barium titanate was analysed. The temperature dependence of the relative dielectric permittivity showed three structural phase transitions that are characteristic for ferroelectric barium titanate ceramics. The relative dielectric permittivity at the Curie temperature was higher for the attrition-treated sample than for the non-treated barium titanate. The dielectric losses were below 0.04 in both barium titanate ceramics. The grain and grain-boundary contributions to the total resistivity were observed using impedance analyses for both ceramics. A well-defined ferroelectric hysteresis loop and piezoelectric coefficient d₃₃ = 150 pC/N were obtained for the ceramics prepared from the de-agglomerated powder. In this way we were able to demonstrate that by attrition milling of chemically obtained powders the ferroelectric and piezoelectric properties of the ceramics could be enhanced.     

Synthesis of nanoparticles of the giant dielectric material,CaCu<Subscript>3</Subscript>Ti<Subscript>4</Subscript>O<Subscript>12</Subscript> from a precursor route

A complex oxalate precursor, CaCu₃(TiO)₄(C₂O₄)₈·9H₂O, (CCT-OX), was synthesized and the precipitate that obtained was confirmed to be monophasic by the wet chemical analyses, X-ray diffraction, FTIR absorption and TG/DTA analyses. The thermal decomposition of this oxalate precursor led to the formation of phase-pure calcium copper titanate, CaCu₃Ti₄O₁₂, (CCTO) at ≥680°C. The bright-field TEM micrographs revealed that the size of the as synthesized crystallites to be in the 30–80 nm range. The powders so obtained had excellent sinterability resulting in high density ceramics which exhibited giant dielectric constants upto 40000 (1 kHz) at 25°C, accompanied by low dielectric losses, <0.07.     

Synthesis of CeO2 by thermal decomposition of oxalate and kinetics of thermal decomposition of precursor

CeO₂ was synthesized by calcining Ce₂(C₂O₄)₃·8H₂O above 673 K in air. The precursor and its calcined products were characterized using thermogravimetry and differential scanning calorimetry, Fourier transform infrared spectra, X-ray powder diffraction, scanning electron microscopy, and UV–Vis absorption spectroscopy. The result showed that cubic CeO₂ was obtained when the precursor was calcined above 673 K in air for 2 h. The UV–Vis absorption spectroscopy studies showed that superfine CeO₂ behaved as an excellent UV-shielding material. The thermal decomposition of the precursor in air experienced two steps, which are: first, the dehydration of eight crystal water molecules, then the decomposition of Ce₂(C₂O₄)₃ into cubic CeO₂. The values of the activation energies associated with the thermal decomposition of Ce₂(C₂O₄)₃·8H₂O were determined based on the Starink equation.     

Synthesis of Free-Standing Crystalline Barium Titanate Films at Vapor/Liquid or Liquid/Liquid Interface

Synthesis of free-standing crystalline barium titanate (BaTiO₃) films at vapor/liquid or liquid/liquid interface at room temperature has been investigated. High concentration Ba, Ti alkoxides precursor solution (1.2 mol/l) or pre-hydrolyzed precursor solutions by water vapor in a H₂O/Ba molar ratio of 0 to 6 were used as dropping solutions at the interfaces. Transparent gel films were formed when partially hydrolyzed precursors (H₂O/Ba = 2 to 3) were spread out on a N₂/liquid paraffin interface. The films shrank from syneresis and vaporization of the solvent during aging at room temperature. As a result, free-standing transparent films with a thickness of around 1 m and little stoichiometric deviation were obtained by separation from the liquid surface and rinse by hexane. The films consisted of crystalline BaTiO₃ particles of less than a few nanometers. Nanostructured dense BaTiO₃ free-standing films with a grain size less than 100 nm were obtained at 1030°C.     

The effect of synthesis conditions on the structure of compounds formed in the Dy<Subscript>2</Subscript>O<Subscript>3</Subscript>–TiO<Subscript>2</Subscript> system

Crystallization and phase transition processes taking place in the Dy₂O₃–TiO₂ system during the isothermal annealing of the precursors synthesized by co-precipitation were studied. The phase composition of the obtained powders is determined by not only the chemical composition of the precursor (Dy₂O₃: TiO₂ ratio) and annealing temperature but also by the procedure of precursor synthesis determining the uniformity of Dy and Ti distribution in the precursor precipitate. Higher homogeneity of precursor particles provides the formation of almost single-phase nanocrystaline dysprosium titanate (Dy₂TiO₅, Dy₂Ti₂O₇) powders at annealing temperatures of 800–1000°C.     

Theoretical studies of electronic structure and structural properties of anhydrous alkali metal oxalates

Nanocrystalline LiMn₂O₄ was synthesized by calcining LiMn₂(CO₃)_2.5·0.8H₂O above 600 °C in air. The precursor and its calcined products were characterized by thermogravimetry and differential scanning calorimetry, X-ray powder diffraction, and scanning electron microscopy. The result showed that highly crystallization LiMn₂O₄ with cubic structure [space group Fd-3m(227)] was obtained when the precursor was calcined at 600 °C in air for 1.5 h. The thermal process of the precursor in air experienced three steps which involved, at first, the dehydration of 0.8 water molecules, then decomposition of MnCO₃ into Mn₂O₃, at last, reaction of Mn₂O₃ and Li₂CO₃ into cubic LiMn₂O₄. Based on Starink equation, the values of the activation energies associated with the thermal process of LiMn₂(CO₃)_2.5·0.8H₂O were determined. Besides, most probable mechanism functions and thermodynamic functions (ΔS ^≠, ΔH ^≠, and ΔG ^≠) of thermal processes of LiMn₂(CO₃)_2.5·0.8H₂O were also determined.     

Preparation of nanocrystalline BiFeO3 and kinetics of thermal process of precursor

The Bi₂Fe₂(C₂O₄)₅·5H₂O was synthesized by solid-state reaction at low heat using Bi(NO₃)₃·5H₂O, FeSO₄·7H₂O, and Na₂C₂O₄ as raw materials. The nanocrystalline BiFeO₃ was obtained by calcining Bi₂Fe₂(C₂O₄)₅·5H₂O at 600 °C in air. The precursor and its calcined products were characterized by thermogravimetry and differential scanning calorimetry, FT-IR, X-ray powder diffraction, and vibrating sample magnetometer. The data showed that highly crystallized BiFeO₃ with hexagonal structure [space group R3c(161)] was obtained when the precursor was calcined at 600 °C in air for 1.5 h. The thermal process of the precursor in air experienced five steps which involved, at first, the dehydration of an adsorption water molecule, then dehydration of four crystal water molecules, decomposition of FeC₂O₄ into Fe₂O₃, decomposition of Bi₂(C₂O₄)₃ into Bi₂O₃, and at last, reaction of Bi₂O₃ and Fe₂O₃ into hexagonal BiFeO₃. Based on Starink equation, the values of the activation energies associated with the thermal process of Bi₂Fe₂(C₂O₄)₅·5H₂O were determined. Besides, the most probable mechanism functions and thermodynamic functions (ΔS ^≠, ΔH ^≠, and ΔG ^≠) of thermal processes of Bi₂Fe₂(C₂O₄)₅·5H₂O were also determined.     

Preparation and characterization of spherical V2O3 nanopowder

V₂O₃ nanopowder with spherical particles was prepared by reducing pyrolysis of the precursor, (NH₄)₅[(VO)₆(CO₃)₄(OH)₉]·10H₂O, in H₂ atmosphere. The thermolysis process of the precursor in a H₂ flow was investigated by thermogravimetric analysis and differential thermal analysis. The results indicate that pure V₂O₃ forms at 620°C and crystallizes at 730°C. The effects of various reductive pyrolysis conditions on compositions of V₂O₃ products were studied. Scanning electron micrographs show that the particles of the V₂O₃ powder obtained at 650°C for 1 h are spherical about 30 nm in size with more homogeneous distribution. Experiments show that nanopowder has larger adsorption capacity to gases and is more easily reoxidized by air at room temperature than micropowder. Differential scanning calorimetry experiment indicates that the temperature of phase transition of nano-V₂O₃ powder is −119.5°C on cooling or −99.2°C on heating. The transition heats are −12.55 J g⁻¹ on cooling and 11.42 J g⁻¹ on heating, respectively.     

Effect of the composition on the thermal behaviour of the SrSn1−xTixO3 precursor prepared by the polymeric precursor method

Strontium stannate titanate Sr(Sn, Ti)O₃ is a solid solution between strontium stannate (SrSnO₃) and strontium titanate (SrTiO₃). In the present study, it was synthesized at low temperature by the polymeric precursor method, derived from the Pechini process. The powders were calcined in oxygen atmosphere in order to eliminate organic matter and to decrease the amount of SrCO₃ formed during the synthesis. The powders were annealed at different temperatures to crystallize the samples into perovskites-type structures. All the compositions were studied by thermogravimetry (TG) and differential thermal analysis (DTA), infrared spectroscopy (IR) and X-ray diffraction (XRD). The lattice former, Ti⁴⁺ and Sn⁴⁺, had a meaningful influence in the mass loss, without changing the profile of the TG curves. On the other hand, DTA curves were strongly modified with the Ti⁴⁺:Sn⁴⁺ proportion in the system indicating that intermediate compounds may be formed during the synthesis being eliminated at different temperature ranges, while SrCO₃ elimination occurs at higher temperature as shown by XRD and IR spectra.     

Simple Electrodeposition of Dendritic Pd Without Supporting Electrolyte and Its Electrocatalytic Activity Toward Oxygen Reduction and H2O2 Sensing

Metallic palladium (Pd) electrocatalysts for oxygen reduction and hydrogen peroxide (H₂O₂) oxidation/reduction are prepared via electroplating on a gold metal substrate from dilute (5 to 50 mM) aqueous K₂PdCl₄ solution. The best Pd catalyst layer possessing dendritic nanostructures is formed on the Au substrate surface from 50 mM Pd precursor solution (denoted as Pd‐50) without any additional salt, acid or Pd templating chemical species. The Pd‐50 consisted of nanostructured dendrites of polycrystalline Pd metal and micropores within the dendrites which provide high catalyst surface area and further facilitate reactant mass transport to the catalyst surface. The electrocatalytic activity of Pd‐50 proved to be better than that of a commercial Pt (Pt/C) in terms of lower overpotential for the onset and half‐wave potentials and a greater number of electrons (n) transferred. Furthermore, amperometric i–t curves of Pd‐50 for H₂O₂ electrochemical reaction show high sensitivities (822.2 and ?851.9 µA mM^?1 cm^?2) and low detection limits (1.1 and 7.91 µM) based on H₂O₂ oxidation H₂O₂ reduction, respectively, along with a fast response (<1 s).     

Characterization of cerium-based conversion coatings for corrosion protection of AISI-1010 commercial carbon steel

The role of hydrogen peroxide in the formation of cerium conversion coatings by immersing AISI 1010 commercial carbon steel substrates into solutions containing various concentrations of CeCl₃ (0.1, 1, and 10 g L⁻¹) has been investigated as an alternative method for their protection against corrosion. The deposits prepared from the solutions with H₂O₂ consist of yellow thin and non-uniform coatings with agglomerates of small CeO₂ and Ce₂O₃ crystallites whose sizes increased over the metallic surface as the cerium concentration was increased. Cerium pre-treatments in the presence of H₂O₂ displayed layers that were rougher than those synthesized without H₂O₂. A comparison with the chromate conversion pre-treatment is also simultaneously carried out with the discussion of the possible reactions involved in the different stages of process. The coating obtained from the solution containing 0.1 g in 1,000 mL produced better corrosion resistance on the substrate than that observed for its counterparts due to the fact that the surface was more uniformly covered by the conversion coating. The addition of H₂O₂ to the cerate baths improves visible roughness, corrosion resistance of the conversion coatings and bond strength because hydrogen peroxide acts as an oxygen source during the formation of the coatings.     

Superparamagnetic and ferromagnetic behavior of ZnFe2O4 nanoparticles synthesized by microwave-assisted hydrothermal method

Zinc ferrite (ZnFe₂O₄) nanoparticles were successfully synthesized from Zn(NO₃)₂ · 6H₂O and Fe(NO₃)₃ · 9H₂O by microwave hydrothermal method at 150°C for 1 h. Cubic ZnFe₂O₄ with particle size below 7 nm was formed in the solution at pH ≥ 6. The crystallinity and particle size of ZnFe₂O₄ nanoparticles were increased after calcination. The effects of pH of the precursor solution and calcination on the particle size and crystallinity of the particles were studied. At room temperature the products show superparamagnetic and ferromagnetic properties, determined by their size. The formation mechanism of ZnFe₂O₄ was also discussed according to the experimental results.

     

Beiträge zur Chemie des Phosphors. XXXIX. Zur Hydrolyse des Diphosphor-tetrajodids

In the preparation of Ba₂H₂(H₂P₂O₄)₃ by P₂I₄ hydrolysis in barium acetate/acetic acid buffer solution P(II)—P(IV), P(IV)—P(IV), P(III), and P(V) acid are formed in addition to about 17% of the starting phosphorus as P(II)—P(II) acid after separating the Ba₂H₂(H₂P₂O₄)₃. Thus in this reaction a total of 64% of P₂I₄ Phosphorus can be detected as hypodiphosphorous acid H₄P₂O₄. The precipitated yellow reaction product, obtained by water hydrolysis of P₂I₄, contains no solid phosphorus hydride — as believed previously — but as a result of elementary analysis, iodometry, and chromatography, a high molecular-weight phosphorus, hydrogen and oxygen containing substance of statistical stoichiometry with oxydation number ～0 for phosphorus. P? H, P?O, and P? O? P groups could be detected by IR-spectroscopy, but not P? OH groups. The P₂I₄ hydrolysis probably proceeds via a yellow coloured initial product with trivalent phosphorus, and yields a very complex reaction mixture in which also the intermediates partially still react further.     

Gravimetrische Phosphorbestimmung mit N,N,N′,N′-Tetrakis-(2-hydroxybutyl)-äthylendiammoniumdiperchlorat

This reagent forms a sparingly soluble precipitate, [C₁₈H₄₀O₄N₂H₂]₃[P(Mo₃O₁₀)₄]₂ in presence of phosphate and molybdate in hydrochloric acid solution. The precipitate is well suitable for a gravimetric determination of phosphorus (factor 0.013190). Standard deviation was ± 0.3 mg for 93.94 mg and ± 0.6 mg for 1174,2 mg of precipitate. Fe, Mn, Cr, Co and Ni do not interfere up to a 500-fold excess.     

The monooxidation of ethylene with hydrogen peroxide on the per-FTPhPFe<Superscript>3+</Superscript>OH/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> biomimetic

The gas-phase monooxidation of ethylene by hydrogen peroxide on a biomimetic heterogeneous catalyst (per-FTPhPFe³⁺OH/Al₂O₃) was studied under comparatively mild conditions. The biomimetic oxidation of ethylene with hydrogen peroxide was shown to be coherently synchronized with the decomposition of H₂O₂. Depending on reaction medium conditions, one of two desired products was formed, either ethanol or acetaldehyde. The kinetics and probable mechanism of ethylene transformation were studied.     

Determination of hydrogen peroxide based on calcined layered double hydroxide-modified glassy carbon electrode in flavored beverages

In this paper, we developed an amperometric hydrogen peroxide (H₂O₂) sensor based on cobalt-containing calcined layered double hydroxide (Co CLDH). The electrocatalytic activity of the Co CLDH towards the determination of H₂O₂ showed a fast response and high sensitivity. Moreover, the sensor exhibited good reproducibility and long-term stability. The superior electrocatalytic response to H₂O₂ is mainly attributed to the large surface area, minimized diffusion resistance, and enhanced electron transfer of the synthesized Co CLDH. This method with good analytical performance, low cost, and straightforward preparation made this novel electrode material promising for the determination of trace H₂O₂ in beverages with high accuracy, demonstrating its potential for practical application.