Synthesis of nearly uniform single-walled carbon nanotubes using identical metal-containing molecular nanoclusters as catalysts

Uniform and small-diameter single-walled carbon nanotubes (SWNTs) have been produced using identical molecular nanoclusters containing Fe and Mo atoms with a defined molecular formula and a specific structure as catalysts in a chemical vapor deposition method. The average diameter of the SWNTs produced in these experiments is 1.0 nm with a standard deviation for the diameter distribution of 17%. The diameters of SWNTs were obtained by atomic force microscopy and Raman spectroscopy.     

Single-walled carbon nanotube growth using [Fe(3)(mu(3)-O)(mu-O(2)CR)(6)(L)(3)](n+) complexes as catalyst precursors

We present herein the VLS growth of SWNTs from oxo-hexacarboxylate-triron precursors, [Fe(3)O(O(2)CCH(3))(6)(EtOH)(3)] and [Fe(3)O(O(2)CCH(2)OMe)(6)(H(2)O)(3)][FeCl(4)], on spin-on-glass surfaces, using C(2)H(4)/H(2) (750 degrees C) and CH(4)/H(2) (800 and 900 degrees C) growth conditions. The SWNTs have been characterized by AFM, SEM and Raman spectroscopy. The characteristics of the SWNTs are found to be independent of the identity of the precursor complex or the solvent from which it is spin-coated. The as grown SWNTs show a low level of side-wall defects and have an average diameter of 1.2-1.4 nm with a narrow distribution of diameters. At 750 and 800 degrees C the SWNTs are grown with a range of lengths (300 nm-9 microm), but at 900 degrees C only the longer SWNTs are observed (6-8 microm). The yield of SWNTs per unit area of catalyst nanoparticle decreases with the growth temperature. We have demonstrated that spin coating of molecular precursors allows for the formation of catalyst nanoparticles suitable for growth of SWNTs with a high degree of uniformity in the diameter, without the formation of preformed clusters of a set diameter.     

Molecular dynamics study of the catalyst particle size dependence on carbon nanotube growth

The molecular dynamics method, based on an empirical potential energy surface, was used to study the effect of catalyst particle size on the growth mechanism and structure of single-walled carbon nanotubes (SWNTs). The temperature for nanotube nucleation (800-1100 K), which occurs on the surface of the cluster, is similar to that used in catalyst chemical vapor deposition experiments, and the growth mechanism, which is described within the vapor-liquid-solid model, is the same for all cluster sizes studied here (iron clusters containing between 10 and 200 atoms were simulated). Large catalyst particles, which contain at least 20 iron atoms, nucleate SWNTs that have a far better tubular structure than SWNTs nucleated from smaller clusters. In addition, the SWNTs that grow from the larger clusters have diameters that are similar to the cluster diameter, whereas the smaller clusters, which have diameters less than 0.5 nm, nucleate nanotubes that are approximately 0.6-0.7 nm in diameter. This is in agreement with the experimental observations that SWNT diameters are similar to the catalyst particle diameter, and that the narrowest free-standing SWNT is 0.6-0.7 nm.     

CVD growth of single-walled carbon nanotubes with narrow diameter distribution over Fe/MgO catalyst and their fluorescence spectroscopy

Single-walled carbon nanotubes (SWNTs) with a narrow diameter distribution are synthesized by thermal chemical vapor deposition (CVD) of methane over Fe/MgO catalyst on the basis of parametric study considering Fe loading, reaction temperature and time, methane concentration, and structure of a support material. We found that the porous MgO support gives the SWNTs with a narrow diameter distribution with the mean diameter and standard deviation of 0.93 and 0.06 nm, respectively, only when the Fe loading and reaction temperature are relatively low. The higher Fe loading and/or the higher reaction temperature enlarged the nanotube diameter, forming double-walled carbon nanotubes (DWNTs) in addition to SWNTs. This result indicates that only the diameter of Fe nanoparticles determines the growth of either SWNTs or DWNTs on the MgO support. The fluorescence and absorption spectra of the nanotube dispersion in D(2)O solution with sodium dodecyl sulfate (SDS) were studied to identify their chirality distribution. The fluorescence of the uniform-diameter SWNTs indicates the formation of the near armchair structures. On the other hand, the SWNTs synthesized over the catalyst with a high Fe loading, 3 wt %, showed a wide chirality distribution including the near zigzag structure. The synthesis of the SWNTs with a narrow diameter distribution could be applied to the selection of SWNTs with a specific chirality based on postsynthesis separation.     

High-yield synthesis of single-wall carbon nanotubes on MCM41 using catalytic chemical vapor deposition of acetylene

High-quality single-wall carbon nanotubes (SWNTs) with narrow diameter distribution have been grown on Fe/Co-loaded MCM41 by using acetylene as the carbon source within a short reaction period, typically 10 min or less. The optimum temperature for SWNTs synthesis is 850 degrees C. Longer reaction time (i.e., 30 min) favors the formation of multiwall carbon nanotubes (MWNTs) and graphitic carbon. When the reaction time is reduced to less than 10 min, formation of MWNTs and graphitic carbon is greatly suppressed, and high-quality SWNTs dominates the yield. The surface of the as-grown SWNTs is found to be free from amorphous carbon, as observed from high-resolution transmission electron microscope (HRTEM) analysis. Raman spectral data show a G/D ratio above 10, indicating that the as-grown SWNTs have very few defects. Furthermore, radial breathing mode (RBM) analysis reveals that the diameter distribution of the current SWNTs is narrow and ranges from 0.64 to 1.36 nm.     

活性碳纤维阴极电芬顿反应降解微囊藻毒素研究

以具有高比表面积的活性碳纤维作为阴极,通过电芬顿反应降解水中微囊藻毒素(MCRR,MCLR)的电化学方法系统考察了电流密度、pH值和Fe2+浓度等因素对微囊藻毒素降解效果的影响.实验结果表明,在Fe2+浓度为1.0mmol/L和电流密度为6.6mA/cm2条件下,电化学处理60min,MCRR(8.81mg/L)去除率为75%,MCLR(6.36mg/L)去除率为94%.证明过氧化氢可以通过电化学还原在活性碳纤维阴极表面高效产生,微囊藻毒素可被高效降解去除.     

高温煅烧Mo改性的Fe／MgO催化剂用于制备管径分布均一的单壁碳纳米管

研究了在以甲烷化学气相沉积法制备单壁碳纳米管的过程中高温煅烧预处理(900℃煅烧10h)对Mo改性Fe/MgO催化剂的作用.发现这种预处理有利于Fe在催化剂中的稳定和分散,从而制备出管径均一的单壁碳纳米管.采用能谱元素分析、高分辨透射电镜、X射线衍射、比表面积测量、拉曼光谱和热重分析对样品进行了表征.结果表明,在碳纳米管生长的过程中,铁元素在催化剂表面富集,单壁碳纳米管生长于富集铁的纳米颗粒上,并存在碳管直径与铁颗粒尺寸的依赖关系.Mo存在时可煅烧形成FeMoO4复合氧化物,后者比MgFe2O4相更加稳定.Mo/Fe比例对提高单壁碳纳米管的生长密度、纯度与管径均一性等均有明显影响.上述研究对进一步精确控制制备单壁碳纳米管有重要意义.     

聚(2-甲氧基-5-辛氧基)对苯乙炔/单壁碳纳米管复合材料的光物理性能研究

采用原位脱氯化氢缩合聚合法制备了聚(2-甲氧基-5-辛氧基)对苯乙炔/单壁碳纳米管(PMOCOPV/SWNTs)复合材料. 红外光谱和拉曼光谱证实了在SWNTs表面的包覆层为PMOCOPV. 高分辨透射电子显微镜观察发现, PMOCOPV/SWNTs复合材料直径为4~7 nm, 其中PMOCOPV包覆层厚度约为2~5 nm. 紫外-可见吸收光谱表明, 随着SWNTs含量的增加, PMOCOPV/SWNTs的吸收发生蓝移且强度提高. 荧光光谱研究表明, 随着SWNTs含量的增加, PMOCOPV/SWNTs的最大发射波长发生蓝移且强度减小, SWNTs与PMOCOPV之间形成了光致电子转移体系, 使π电子离域程度增加, 导致荧光量子效率降低. 根据E_g与入射光子能量hν的关系, 拟合了PMOCOPV/SWNTs薄膜的光学禁带宽度, 发现随着SWNTs含量的增加, E_g逐渐减小. 采用简并四波混频方法测试其三阶非线性极化率χ⁽³⁾, 结果表明, 随着SWNTs含量的增加, PMOCOPV/SWNTs复合体的非线性光学响应逐渐增强, 说明PMOCOPV与SWNTs之间形成了分子间光致电子转移体系, 产生了复杂的分子间π-π电子非线性运动.     

Cobalt-filled apoferritin for suspended single-walled carbon nanotube growth with narrow diameter distribution

Cobalt-filled apoferritin (Co-ferritin) was, for the first time, used as a wet catalyst for the synthesis of single-walled carbon nanotubes (SWNTs) with narrow diameter distribution. Co-ferritins were spin-coated and converted to cobalt nanoparticles by calcination. Using chemical vapor deposition, suspended networks of SWNTs were formed on pillar-structured substrates. The suspended SWNTs show narrow tube diameter distribution with a relatively good graphite structure. By virtue of the low diffusion coefficient of cobalt, Co-ferritin might be more useful for narrow diameter SWNTs growth than ferritins, which encase iron particles.     

定位生长法制备AFM单壁碳纳米管针尖

采用粘性胶状物作为生长单壁碳纳米管(SWNTs)的催化剂前驱体, 在原子力显微镜下驱动废旧的硅探针粘附该种胶状物,随后进行化学气相沉积(CVD), 实现了SWNTs在硅探针末端的定位生长, 成功地制备出了SWNT针尖. 对SWNTs及SWNT 针尖进行了表征, 并对针尖的稳定成像条件进行了分析. 结果表明, 针尖一般由5-10 nm 的SWNT 管束构成, 伸出长度仅为几百纳米, 受热振动影响较小, 无需后处理即可稳定地成像, 成像分辨率与新的硅探针相当.     

Simple Dip-Coating Process for the Synthesis of Small Diameter Single-Walled Carbon Nanotubes-Effect of Catalyst Composition and Catalyst Particle Size on Chirality and Diameter

We report on a dip-coating method to prepare catalyst particles (mixture of iron and cobalt) with a controlled diameter distribution on silicon wafer substrates by changing the solution's concentration and withdrawal velocity. The size and distribution of the prepared catalyst particles were analyzed by atomic force microscopy. Carbon nanotubes were grown by chemical vapor deposition on the substrates with the prepared catalyst particles. By decreasing the catalyst particle size to below 10 nm, the growth of carbon nanotubes can be tuned from few-walled carbon nanotubes, with homogeneous diameter, to highly pure single-walled carbon nanotubes. Analysis of the Raman radial breathing modes, using three different Raman excitation wavelengths (488, 633, and 785 nm), showed a relatively broad diameter distribution (0.8-1.4 nm) of single-walled carbon nanotubes with different chiralities. However, by changing the composition of the catalyst particles while maintaining the growth parameters, the chiralities of single-walled carbon nanotubes were reduced to mainly four different types, (12, 1), (12, 0), (8, 5), and (7, 5), accounting for about 70% of all nanotubes.     

FeCo/MgO催化生长体相单壁碳纳米管的直径调控

单壁碳纳米管的直径可控生长是碳纳米管生长与应用领域的重要问题。直径在0.9–1.2 nm范围内的碳纳米管非常适合应用于近红外荧光生物成像领域和量子器件单光子光源之中。本文使用FeCo/MgO催化剂生长出了直径在这一范围内的体相单壁碳纳米管,并研究了催化剂制备和CVD生长条件对碳纳米管直径的影响。催化剂前驱体的制备是获得小尺寸催化剂颗粒的关键步骤。在浸渍过程中,使用难水解的金属硫酸盐作为前驱体、降低浸渍pH以及加入络合剂分子都会抑制溶液干燥过程中金属盐的水解,从而控制催化剂的尺寸,使其适合于生长出直径可控的单壁碳纳米管。在CVD生长过程中,使用乙醇作为碳源、使用较低的碳氢比例也有利于小直径碳纳米管的生长。     

单壁碳纳米管的CVD合成及管径分布

甲烷在以活性氧化铝为载体的Fe、Co、Ni、Ru等催化剂上于850 ℃分解并生成直径为0.8～5 nm的单壁碳纳米管.预先将催化剂在1100 ℃焙烧,能够减少产物中无定形碳的生成.拉曼光谱结果表明,由该法制备的碳纳米管的管径分布主要受温度的影响,较低温度有利于较小直径的单壁碳纳米管的生成和较好的管径选择性.     

Influence of the catalyst type on the growth of carbon nanotubes via methane chemical vapor deposition

The preparation of the catalyst is one of the key parameters which governs the quality of carbon nanotubes (CNTs) grown by catalyzed chemical vapor deposition (CVD). We investigated the influence of three different procedures of catalyst preparation on the type and diameter of CNTs formed under identical growth conditions via methane CVD. In the first one, chemically synthesized colloidal iron oxide or iron molybdenum alloy nanoparticles were used, which were homogeneously deposited on silicon substrates by spin coating to prevent them from coalescence under CVD growth conditions. The obtained multiwall CNTs (MWNTs) exhibited diameters corresponding to the catalyst particle size, whereas no formation of single-wall CNTs (SWNTs) was observed. In the second method, commercial porous alumina nanoparticles were used in association with iron and molybdenum salts and the Fe/Mo catalyst was formed in situ. We determined that the alumina concentration significantly influenced the morphology of the catalyst and that below a critical value of the range of 1 g/L no CNTs were formed. While yielding nearly defect-free SWNTs, their diameter could not be controlled using this procedure, resulting in a large distribution of tube sizes. In a third, new preparation method, associating alumina and iron-based nanoparticles, SWNTs of a different size and narrower diameter distribution as compared to the second method were obtained. Our results are evidence of the essential role of alumina particles in the formation of SWNTs, and the newly developed method opens up a way to the synthesis of diameter-controlled SWNTs via catalyzed CVD.     

A rapid synthesis of iron phosphate nanoparticles via surface-mediated spontaneous reaction for the growth of high-yield, single-walled carbon nanotubes

The direct formation of iron phosphate nanoparticles on hydroxyl-terminated SiO(2)/Si substrates with a narrow size distribution (average diameter = 2.2 nm) is achieved by a simple room temperature spontaneous reaction of ferric chloride and phosphoric acid. Single-walled carbon nanotubes (SWNTs) are grown in high yield from the synthesized iron phosphate nanoparticles by the thermal chemical vapor deposition (CVD) method, as confirmed by atomic force microscopy (AFM) and Raman spectroscopy. Furthermore, three-terminal, p-type, nanotube network field effect transistor (FET) devices are successfully fabricated using the synthesized SWNTs via the photolithography technique. The reduced solubility of Fe(III) ions when they form iron phosphate salts in aqueous media is the main driving force for the nanoparticle formation. Systematic control experiments reveal that the surface property, concentration, and pH of the reaction solution play equally important roles in the formation of nanoparticles.     

Narrow (n,m)-distribution of single-walled carbon nanotubes grown using a solid supported catalyst

Unusually structure-selective growth of single-walled carbon nanotubes (SWNTs) has been attained using a CVD method with a solid supported catalyst. In this method, CO feedstock disproportionates on silica-supported catalytic nanoclusters of Co that are formed in situ from mixed salts of Co and Mo. The nanotube products are analyzed by spectrofluorimetry to reveal distributions resolved at the level of individual (n,m) structures. Two structures, (6,5) and (7,5), together dominate the semiconducting nanotube distribution and comprise more than one-half of that population. The average diameter of produced SWNTs is only 0.81 nm, and a strong propensity is found favoring chiral angles near the armchair limit.     

Preferential growth of single-walled carbon nanotubes on silica spheres by chemical vapor deposition

The preferential growth of single-walled carbon nanotubes (SWNTs) on silica spheres with various diameters was realized for the first time by chemical vapor deposition (CVD) of methane. SWNTs tend to wrap the silica spheres to form a new superstructure of uniform SWNT nanoclaws when the diameters of the silica spheres are larger than 400 nm. The SWNTs obtained on silica spheres have highly graphitic tubular walls as characterized by Raman spectroscopy and HRTEM. This is a new method to obtain tunable uniform elastic deformation of SWNTs, which may act as the model for the study about the effect of delocalized bending on the properties of SWNTs. In addition, the combination of SWNTs with monodispersed silica spheres could conveniently integrate SWNTs into photonic crystals.     

Selective synthesis combined with chemical separation of single-walled carbon nanotubes for chirality selection

Single-walled carbon nanotubes (SWNTs) are potential materials for future nanoelectronics. Since the electronic and optical properties of SWNTs strongly depend on tube diameter and chirality, obtaining SWNTs with narrow (n,m) chirality distribution by selective growth or chemical separation has been an active area of research. Here, we demonstrate that a new, bimetallic FeRu catalyst affords SWNT growth with narrow diameter and chirality distribution in methane CVD. At 600 degrees C, methane CVD on FeRu catalyst produced predominantly (6,5) SWNTs according to UV-vis-NIR absorption and photoluminescence excitation/emission (PLE) spectroscopic characterization. At 850 degrees C, the dominant semiconducting species produced are (8,4), (7,6), and (7,5) SWNTs, with much narrower distributions in diameter and chirality than materials grown by other catalysts. Further, we show that narrow diameter/chirality growth combined with chemical separation by ion exchange chromatography (IEC) greatly facilitates achieving single (m,n) SWNT samples, as demonstrated by obtaining highly enriched (8,4) SWNTs with near elimination of metallic SWNTs existing in the as-grown material.     

Photochemical Behavior of Single‐Walled Carbon Nanotubes in the Presence of Propylamine

This report describes the photochemical behavior of single‐walled carbon nanotubes (SWNTs) in the presence of propylamine. The SWNTs are characterized by absorption and Raman spectroscopy. The spectral changes due to photoirradiation indicate that reactions occur predominantly with the metallic SWNTs and small‐diameter SWNTs. The detection of amine radicalcation species by ESR spectroscopy reveals photoinduced electron transfer from the amine to the excited SWNTs. After exposure of the photoirradiated SWNTs to air, the characteristic spectra were recovered, except for that of the small‐diameter SWNTs. The results suggest that, after photoreduction of the SWNTs, subsequent selective sidewall functionalization of the small‐diameter SWNTs occurs.     

Carbon nanotube reinforced NiO fibers for rechargeable lithium batteries

Single-wall carbon nanotubes (SWNTs) reinforced NiO fibers with diameter smaller than 50 nm have successfully been prepared by electrospinning method combined with calcination. The SWNTs homogeneously distributed in the NiO fibers were characterized by high resolved transmission electron microscopy, selected area electron diffraction, and Raman spectroscopy. Charge and discharge data showed that 3D network structures of NiO–SWNTs fibers exhibited a relatively higher reversible capacity and lower capacity loss than that of NiO at the charge and discharge current density of 2C, and its discharge capacity was about 337 mAh/g after 20 cycles. Our results demonstrated that the SWNTs reinforced fibers had a better cycling performance at large charge and discharge current densities.