New-type low-cost cathode materials for Li-ion batteries: Mikasaite-type Fe2(SO4)3

In the present work, a new-type low-cost lithium ion battery cathode material, the Mikasaite-type iron sulfate, has been studied. It can be prepared by heating the water-containing iron sulfate raw chemicals in air atmosphere. The experimental results have shown that the oxidation and the reduction peaks are 3.92 and 3.37 V in the cyclic voltammogram, respectively, when the scanning rate is 0.05 mV s^?1. The galvanostatic measurements have explored that the voltage plateau during charging is slightly less than 3.70 V and the discharge voltage plateau is 3.40 V for the first cycle and 3.50 V for the following cycles at 0.1 C rate. The discharge capacity in the first cycle can reach 116 mAh g^?1, about 87 % of the theoretical capacity (134 mAh g^?1). It is believed that the product in the fully discharged state is Li₂Fe₂(SO₄)₃. However, the insertion reaction is reversible only for the second lithium ion. During cycling, the reversible capacity remains about 60 mAh g^?1. Further capacity fade is not found in the 20 discharge–charge cycles. The electrochemical impedance measurements have shown that there are two compressed semicircles in the Nyquist plots and a Warburg impedance in the low-frequency domain. The high-frequency semicircle is related with the electrode’s structural factor and the intermediate-frequency semicircle corresponds to the charge-transfer process.     

Li2MnSiO4/carbon nanofiber cathodes for Li-ion batteries

Pure single-phase Li₂MnSiO₄ nanoparticle-embedded carbon nanofibers have been prepared for the first time via a simple sol-gel and electrospinning technique. They exhibit an improved electrochemical performance over conventional carbon-coated Li₂MnSiO₄ nanoparticle electrodes, including a high discharge capacity of ～200 mAh g^?1, at a C/20 rate, with the retention of 77 % over 20 cycles and a 1.6-fold higher discharge capacity at a 1 C rate.     

LiNi1/3Co1/3Mn1/3O2 cathode materials for LIB prepared by spray pyrolysis I: the spectral, structural, and electro-chemical properties

Layered lithium ion battery cathode material LiNi_1/3Co_1/3Mn_1/3O₂ with uniform particle size of about 6 μm was synthesized by a spray pyrolysis method. Infrared and X-ray diffraction analyses show that the pyrolysis at 1,000 °C for 2 s in the tube furnace eliminates nearly all the organic components but is still not enough for the complete crystallization of LiNi_1/3Co_1/3Mn_1/3O₂ materials. Therefore, further annealing at 850 °C is needed. The prepared LiNi_1/3Co_1/3Mn_1/3O₂ cathode materials show excellent electrochemical performances. By increasing the C-rates, the cell shows discharge capacities of 159.3, 148.2, 133.7, and 125.7 mAh g^?1 at 0.1, 0.2, 0.5, and 1C rates, respectively. Only 2.1 mAh g^?1 capacity loss is observed when back to 0.1C rate. Moreover, LiNi_1/3Co_1/3Mn_1/3O₂ cathode retains 96, 97.7, 97.1, 94.5, and 97.1 % of its initial discharge capacities after 20 cycles at 0.1, 0.2, 0.5, 1, and back to 0.1C rates, respectively. More than 97 % coulombic efficiencies are observed at all the current densities in 20 cycles.     

Li3V2(PO4)3 modified LiFePO4/C cathode materials with improved high-rate and low-temperature properties

LiFePO₄/C surface modified with Li₃V₂(PO₄)₃ is prepared with a sol–gel combustion method. The structure and electrochemical behavior of the material are studied using a wide range of techniques such as X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope, galvanostatic charge–discharge, and electrochemical impedance spectroscopy. It is found that LiFePO₄/C surface modified with Li₃V₂(PO₄)₃ has the better electrochemical performance. The discharge capacity of the as-prepared material can reach up to 153.1, 137.7, 113.6, and 93.3 mAh g^?1 at 1, 2, 5, and 10 C, respectively. The capacitance of the LiFePO₄/C modified by Li₃V₂(PO₄)₃ is higher under lower discharging rate at ?20 °C, and the initial discharge capacity of 0.2 C is 131.4 mAh g^?1. It is also demonstrated that the presence of Li₃V₂(PO₄)₃ in the sample can reduce the charge transfer resistance in the range of ?20 to 25 °C, resulting in the enhanced electrochemical catalytic activity.     

Sulfur/microporous carbon composites for Li-S battery

A commercial carbon black with microporous framework is used as carbon matrix to prepare sulfur/microporous carbon (S/MC) composites for the cathode of lithium sulfur (Li-S) battery. The S/MC composites with 50, 60, and 72 wt.% sulfur loading are prepared by a facile heat treatment method. Electrochemical performance of the as-prepared S/MC composites are measured by galvanostatic charge/discharge tests, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS), with carbonate-based electrolyte of 1.0 M LiPF₆/(PC-EC-DEC). The composite with 50 wt.% sulfur presents the optimized electrochemical performance, including the utilization of active sulfur, discharge capacity, and cycling stability. At the current density of 50 mA g^?1, it can demonstrate a high initial discharge capacity of 1624.5 mAh g^?1. Even at the current density of 800 mA g^?1, the initial capacity of 1288.6 mAh g^?1 can be obtained, and the capacity can still maintain at 522.8 mAh g^?1 after 180 cycles. The remarkably improved electrochemical performance of the S/MC composite with 50 wt.% sulfur are attributed to the carbon matrix with microporous structure, which can effectively enhance the electrical conductivity of the sulfur cathode, suppress the loss of active material during charge/discharge processes, and restrain the migration of polysulfide ions to the lithium anode.     

A free-standing and thermostable polymer/plastic crystal electrolyte for all-solid-state lithium batteries

All-solid-state lithium batteries using flexible solid electrolytes instead of combustible organic liquid electrolytes are the ultimate solution to address the safety problem of commercialized lithium ion batteries. In this study, a free-standing and thermostable polymer/plastic crystal composite electrolyte (PPCE) based on polymerized trimethylolpropane trimethacrylate (TMPTMA)-1, 6-hexanediol diacrylate (HDDA) matrix, and plastic crystal electrolyte was prepared for all-solid-state lithium batteries. The polymerized TMPTMA-HDDA-based matrix of a porous network structure coupled with plastic crystal electrolyte (PCE) in the pores reveals good compatibility. The as-synthesized PPCE possesses excellent flexible performance, thermostability, and high conductivity, showing that PPCE can reach 8.53 × 10^?4 S cm^?1 with 7.5 wt% monomers (PPCE-7.5%) at 25 °C under a stability electrochemical window above 5.2 V. The assembled lithium batteries Li|PPCE|LiFePO₄ exhibit high capacity and highly cycling stability at room temperature, indicating great potential of all-solid-state lithium batteries.     

Urea-assisted solvothermal synthesis of monodisperse multiporous hierarchical micro/nanostructured ZnCo<Subscript>2</Subscript>O<Subscript>4</Subscript> microspheres and their lithium storage properties

High-quality monodisperse multiporous hierarchical micro/nanostructured ZnCo₂O₄ microspheres have been fabricated by calcinating the Zn_1/3Co_2/3CO₃ precursor prepared by urea-assisted solvothermal method. The as-prepared products are characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), high-resolution transmission electron microscopy (HRTEM), and Brunauer-Emmett-Teller (BET) measurement to study the crystal phase and morphology. When tested as anode material for lithium ion batteries, the multiporous ZnCo₂O₄ microspheres exhibit an initial discharge capacity of 1,369 mAh g^?1 (3,244.5 F cm^?3) and retain stable capacity of 800 mAh g^?1 (1,896 F cm^?3) after 30 cycles. It should be noted that the good electrochemical performances can be attributed to the porous structure composed of interconnected nanoscale particles, which can promote electrolyte diffusion and reduce volume change during discharge/charge processes. More importantly, this ZnCo₂O₄ 3D hierarchical structures provide a large number of active surface position for Li⁺ diffusion, which may contribute to the improved electrochemical performance towards lithium storage.     

Self-assembled 3D Co3O4-graphene frameworks with high lithium storage performance

Three-dimensional Co₃O₄-graphene frameworks (3D-CGFs) are prepared with a one-pot hydrothermal method. Co₃O₄ particles are in situ anchored on graphene sheets, and the resulting composite self-assembles into 3D architecture during the hydrothermal treatment. Scanning electron microscope, transmission electron microscope, powder X-ray powder diffraction, and Raman spectroscopy are employed to characterize the sample. When tested as anode materials for lithium-ion batteries, 3D-CGFs demonstrate remarkable electrochemical lithium storage properties, such as large and stable reversible capacity (>530 mAh g^?1 at 500 mA g^?1 over 300 cycles), good capacity retention (88 % retention after 300 cycles at 500 mA g^?1 compared with the 4th cycle), excellent high-rate performance (515 mAh g^?1 at 1 A g^?1), making it a promising candidate for high-performance anode materials, especially for high-rate lithium-ion batteries.     

The effect of different concentrations of Na2SnO3 on the electrochemical behaviors of the Mg-8Li electrode

In this research, the effect of the different concentrations of NaSnO₃ as the electrolyte additive in 0.7 mol L^?1 NaCl solution on the electrochemical performances of the magnesium-8lithium (Mg-8Li) electrode are investigated by methods of potentiodynamic polarization, potentiostatic current-time, electrochemical impedance technique, and scanning electron microscopy (SEM). The corrosion resistance of the Mg-8Li electrode is improved when Na₂SnO₃ is added into the electrolyte solution. The potentiostatic current-time curves show that the electrochemical behaviors of the Mg-8Li electrode in the electrolyte solution containing 0.20 mmol L^?1 Na₂SnO₃ is the best. The electrochemical impedance spectroscopy results indicate that the polarization resistance of the Mg-8Li electrode decreases in the following order with the concentrations of Na₂SnO₃: 0.05 mmol L^?1?>?0.00 mmol L^?1?>?0.30 mmol L^?1?>?0.10 mmol L^?1?>?0.20 mmol L^?1. The scanning electron microscopy studies indicate that the electrolyte additive prevents the formation of the dense oxide film on the alloy surface and facilitates the peeling off of the oxidation products.     

Synthesis and electrochemical behavior of Li2CoSiO4 cathode with pyrrolidinium-based ionic liquid electrolyte for lithium ion batteries

Li₂CoSiO₄, a silicate olivine cathode for lithium rechargeable batteries, is synthesized for the first time by sol–gel method using polyacrylic acid (PAA) as the chelating agent. Coupled thermal and vibrational analysis of the gel and also the X-ray diffraction pattern confirms the formation of the sample at 800 °C. 1-Butyl-1-methyl pyrrolidinium bis(trifluoromethanesulfonyl)imide (BMPyTFSI) solutions of lithium bis(trifuloromethansulfonyl)imide (LiTFSI) having a concentration of 0.2 mol kg^?1 is used as electrolyte. The electrochemical stability window of this electrolyte is found to be >5 V by linear sweep voltammetry technique. The compatibility of Li₂CoSiO₄ with 0.2 mol kg^?1 LiTFSI-BMPyTFSI electrolyte is tested by charge–discharge cycles which show charging and discharging capacities of about 204 and 32 mAh g^?1, respectively, in the first cycle.     

Effects of lithium bis(oxalato)borate on electrochemical stability of [Emim][Al<Subscript>2</Subscript>Cl<Subscript>7</Subscript>] ionic liquid for aluminum electrolysis

Electrodeposition of aluminum from ionic liquids has been considered a promising approach to low-temperature aluminum electrolysis. In this study, we first investigated the electrochemical stability of 1-ethyl-3-methylimidazolium chloride ([Emim][Al₂Cl₇]) electrolyte, which is a typically used electrolyte for aluminum electrodeposition. It was found that part of imidazole ions decomposed on the cathode during the electrolysis process, especially when the temperature was at or over 353 K. In order to enhance the stability of the electrolyte, we further studied the effects of lithium salt and lithium bis(oxalato)borate (LiBOB), on the electrochemical stability of the [Emim][Al₂Cl₇] ionic liquid system. It was found that the electrochemical window of the electrolyte was broadened from 2.59 to 2.74 V at 373 K by addition of 1 mol% LiBOB. With the existence of LiBOB, the reduction current density of Al₂Cl₇ ^- increased before ?0.58 V and the electrodissolution of Al was more complete. The possible mechanism on the LiBOB increases the stability of the electrolyte systems also discussed based on our theoretical calculations.     

Electrochemical lithium storage properties of desert sands

SiO₂ is one of the most promising lithium storage materials for lithium-ion batteries anodes due to its low cost, good environmental compatibility, low working voltage, and high-specific capacity. In this work, the desert sands, which are rich in SiO₂, are investigated as the anode material for lithium-ion batteries. The electrochemical activation, lithium storage capacity, and cycle properties are highly dependent on the particle size distribution of sands. As the average particle sizes of sands gradually decrease, the reversible lithium storage capacity increases from 137 mAh g^?1 (several microns) to 492 mAh g^?1 (several submicrons). The 72 h-milled sands (average particle size: ~1 μm) deliver a stable lithium storage capacity of ~400 mAh g^?1 over 400 cycles with the capacity retention as high as 95%. The reason for the electrochemical activation, lithium storage capacity, and cycle properties of sands associated with their particle size distribution is also discussed.     

Vibrational,electrical, and ion transport properties of PVA-LiClO<Subscript>4</Subscript>-sulfolane electrolyte with high cationic conductivity

Novel solid polymer electrolytes, poly(vinylalcohol)-lithium perchlorate (PVA-LiClO₄) and PVA-LiClO₄-sulfolane are prepared by solvent casting method. The experimental results show that sulfolane addition enhances the ionic conductivity of PVA-LiClO₄ complex by three orders. The maximum ionic conductivity of 1.14 ± 0.20 × 10^?2 S cm^?1 is achieved for 10 mol% sulfolane-added electrolyte at ambient temperature. Polymer-salt-plasticizer interactions are analyzed through attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy. Lithium ion transference number is found by AC impedance spectroscopy combined with DC potentiostatic measurements. The results confirm that sulfolane improves the Li⁺ transference number of PVA-LiClO₄ complex to 0.77 from 0.40. The electrochemical stability window of electrolytes is determined by cyclic voltammetry (CV). The broad electrochemical stability window of 5.45 V vs. lithium is obtained for maximum conducting electrolyte. All-solid-state cell is fabricated using maximum conducting electrolyte, and electrochemical impedance study is carried out. It reveals that electrolyte interfacial resistance with Li electrode is very low. The use of PVA-LiClO₄-sulfolane as a viable electrolyte material for high-voltage lithium ion batteries is ensured.     

A microporous carbon derived from phenol–melamine–formaldehyde resin by K2CO3 activation for lithium ion batteries

A microporous carbon material with large surface area was prepared by carbonizing and activating of phenol–melamine–formaldehyde resin, using K₂CO₃ as activation reagent. The textural characteristics of the carbon materials were characterized by scanning electron microscope, X-ray diffraction, Raman spectra, Brunauer–Emmett–Teller, elemental analyses, respectively. Results showed that the surface area and pore diameter of the activated carbon were 1,610 m² g^?1 and less than 2 nm. Electrochemical lithium insertion properties were also investigated. At a current density of 100 mA g^?1, the activated carbon showed an enormous first-discharge capacity of 2,610 mAh g^?1 and the first charge capacity of 992 mAh g^?1. From the second cycle, the coulombic efficiency went up rapidly to above 95 %. The results indicated it may be a promising candidate as an anode material for lithium secondary batteries.     

Elevated electrochemical property of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> originated from nano-sized Mn<Subscript>3</Subscript>O<Subscript>4</Subscript>

By employment of nano-sized pre-prepared Mn₃O₄ as precursor, LiMn₂O₄ particles have been successfully prepared by facile solid state method and sol-gel route, respectively. And the reaction mechanism of the used precursors of Mn₃O₄ is studied. The structure, morphology, and element distribution of the as-synthesized LiMn₂O₄ samples are characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). Compared with LiMn₂O₄ synthesized by facile solid state method (SS-LMO), LiMn₂O₄ synthesized by modified sol-gel route (SG-LMO) possesses higher crystallinity, smaller average particle size (~175 nm), higher lithium chemical diffusion coefficient (1.17 × 10^?11 cm² s^?1), as well as superior electrochemical performance. For example, the cell based on SG-LMO can deliver a capacity of 85.5 mAh g^?1 at a high rate of 5 °C, and manifests 88.3% capacity retention after 100 cycles at 0.5 °C when cycling at 45 °C. The good electrochemical performance of the cell based on SG-LMO is ascribed mainly to its small particle size, high degree of dispersion, and uniform element distribution in bulk material. In addition, the lower polarization potential accelerates Li⁺ ion migration, and the lower atom location confused degree maintains integrity of crystal structure, both of which can effectively improve the rate capability and cyclability of SG-LMO.     

Improved cycling performances with high sulfur loading enabled by pre-treating lithium anode

Lithium nitrate (LiNO₃) is reported as an effective additive to protect lithium anode in rechargeable lithium-sulfur battery. However, for its strong oxidation, cells containing LiNO₃ still suffer from safety problems and poor cycle performance since LiNO₃ can be reduced on cathode to form some irreversible products. In this study, a facile and effective method to pre-passivate lithium anode is proposed by simply immersing lithium plates in LiNO₃ solution. The electrochemical properties show that the pretreatment is favorable for the construction of a protection layer on the surface of lithium anode. Cells with pretreated lithium show the coulombic efficiency of 80.6 % in the first cycle and 87.2 % after 100 cycles, far higher than the one with pure lithium. The discharge capacity is retained at 702 mA h g^?1 after 100 cycles, and the result is better than those directly adding LiNO₃ in electrolyte. It is believed that these improvements result from the high stability of surface film during the charge and discharge process, which can stabilize the structure of anode and suppress the shuttle effect.     

The intercalation/deintercalation kinetic studies on the structure-integrated cathode material 0.5Li2MnO3 0.5LiNi0.5Mn0.5O2

A cathode material, 0.5Li₂MnO₃ 0.5LiNi_0.5Mn_0.5O₂, was prepared by citric acid-assisted sol–gel method and its electrochemical performance was investigated. It delivered a charge capacity of 270 mAh g^?1 and a discharge capacity of 189 mAh g^?1 in the first cycle. With the increase of current density from 14 to 28 mA g^?1, the discharge capacity dropped severely to 130 mA g^?1. Obviously, the rate capability of the material was inferior to most of the oxide cathode materials. The diffusion coefficient of this material was calculated to be 6.04?×?10^?12 cm² s^?1 from the results of cyclic voltammetry measurements. Moreover, diffusion coefficients between 3.13?×?10^?12 and 1.22?×?10^?10 cm² s^?1 in the voltage range of 3.8–4.7 V were obtained by capacity intermittent titration technique. This, together with the localized Li₂MnO₃ domains in the crystal structure, may validate the poor rate capability.     

Synthesis and performance of Li2NiTi3O8 as a new anode material for lithium-ion batteries

The titanate spinel Li₂NiTi₃O₈ is proposed for the first time as a new anode for lithium-ion batteries and successfully synthesized via a facile ball-milling assisted solid-state reaction method. The sample is characterized by X-ray diffraction patterns (XRD), scanning electron microscope (SEM), transmission electron microscopy (TEM), galvanostatic charge–discharge tests, cyclic voltammetry (CV) tests, and electrochemical impedance spectroscopy (EIS). The results reveal that the Li₂NiTi₃O₈ nanoparticles have well-distributed morphology, and the particle size ranges between 100 and 300 nm. Although the initial coulombic efficiency is only 56.3 %, the Li₂NiTi₃O₈ electrode still exhibits a high rate capability and excellent cycling stability. The Li₂NiTi₃O₈ anode provides a large capacity of 212.3 mAh g^?1 at 0.1 A g^?1 after 10 cycle, which is close to its theoretical capacity (223.6 mAh g^?1). Even after 100 cycles, it still delivers a quite high capacity of 203.98 mAh g^?1, with no significant capacity fading. This indicates that the as-synthesized Li₂NiTi₃O₈ material is a promising anode material for lithium-ion batteries.     

Electrical and electrochemical properties of carbon nanotube-based free standing LTO electrodes for current collector-free Li-ion batteries

The spinel lithium titanate oxide (Li₄Ti₅O₁₂, LTO) has been extensively studied as one of the most promising alternatives to carbon materials in energy conversion and storage devices, due to its high structural and thermal stability, rate capability, and excellent cycling stability. In this study, Li₄Ti₅O₁₂/multi-walled carbon nanotubes (LTO-MWCNTs) free-standing and flexible composite electrodes/buckypapers were prepared via tape casting technique and well compared with commercially available LTO. The structural, morphological, electrical and electrochemical properties of LTO-MWCNTs buckypaper as well as LTO were studied. The electrical conductivity of LTO-based buckypaper was found to be very high i. e, 4.4 × 10² Scm⁻¹ at room temperature. Further, the buckypaper prepared by synthesized LTO showed higher specific capacity (166 mAhg⁻¹) compared to commercially available LTO (137 mAhg⁻¹) at 0.2 C rate. The enhanced electrochemical performance of as-synthesized LTO-based buckypaper is mainly attributed to the higher electronic conductivity and homogeneous distribution of particles with its small size which facilitates large amount of active sites for lithium insertion and also short diffusion paths.     

A novel and shortcut method to prepare ionic liquid gel polymer electrolyte membranes for lithium-ion battery

The ionic liquid polymer electrolyte (IL-PE) membrane is prepared by ultraviolet (UV) cross-linking technology with polyurethane acrylate (PUA), methyl methacrylate (MMA), ionic liquid (Py₁₃TFSI), lithium salt (LiTFSI), ethylene glycol dimethacrylate (EGDMA), and benzoyl peroxide (BPO). N-methyl-N-propyl pyrrolidinium bis(trifluoromethanesulfonyl)imide (Py₁₃TFSI) ionic liquid is synthesized by mixing N-methyl-N-propyl pyrrolidinium bromide (Py₁₃Br) and lithium bis(trifluoromethanesulfonyl)imide (LiTFSI). The addition of Py₁₃TFSI to polymer electrolyte membranes leads to network structures by the chain cross-linking. The resultant electrolyte membranes display the room temperature ionic conductivity of 1.37 × 10^?3 S cm^?1 and the lithium ions transference number of 0.22. The electrochemical stability window of IL-PE is about 4.8 V (vs. Li⁺/Li), indicating sufficient electrochemical stability. The interfacial resistances between the IL-PE and the electrodes have the less change after 10 cycles than before 10 cycles. IL-PE has better compatibility with the LiFePO₄ electrode and the Li electrode after 10 cycles. The first discharge performance of Li/IL-PE/LiFePO₄ half-cell shows a capacity of 151.9 mAh g^?1 and coulombic efficiency of 87.9%. The discharge capacity is 131.9 mAh g^?1 with 95.5% coulombic efficiency after 80 cycles. Therefore, the battery using the IL-PE exhibits a good cycle and rate performance.