基于羧基化碳纳米管修饰电极伏安法同时测定痕量锢和铝

基于羧基化多壁碳纳米管(c-MWCNT),制备了可同时测定In3+和Al3+的新型碳材料修饰电极.利用循环伏安法(CV)和交流阻抗法(EIS)对此修饰电极进行了表征,用线性扫描伏安法(LSV)研究了In3+与Al3+共存于修饰电极上的电化学行为.与裸玻碳电极相比,新型碳材料修饰电极的电化学活性得到很大提高;In3+与A...     

Electorchemical Studies of Cytochrome c on Electodes Modified by Single—Wall Carbon Naotubes

Single-wall carbon nanotubes(SWNTs) modified gold electrodes were prepared by using two different methods.The electrochemical behavior of cytochrome c on the modified gold electrodes was investigated.The first kind of SWNT-modified electrode (noted as SWNT/Au electrode)was prepared by the adsorption of carboxylterminated SWNTs from DMF dispersion on the gold electrode.The oxidatively processed SWNT tips were covalently modified by coupling with amines (AET) to form amide linkage.Via Au-S chemical bonding,the self-assembled monolayer of thiol-unctionalized nanotubes on gold surface was fabricated so as to prepare the others SWNT-modified electrode (noted as SWNT/AET/Au electrode).It was shown from cyclic voltammetry cxperiments that cytochrome c exhibited direct electrochemical responses on the both electrodes, but only the current of controlled diffusion existed on the SWNT/Au electrode while both the currents of controlled diffusion and adsorption of cytochrome c occurred on the SWNT/AET/Au electrode.Photoelastic Modulation Infared Reflection Absorpthion Spectroscopy (PEM-IRRAS) and Quartz Crystal Microbalance (QCM) were employed to verify the adsorption of SWNTs on the gold electrodes.The results proved that SWNTs could enhance the direct electron transfer proecss between the electrodes and redox proteins.     

铜/活性炭复合材料的电化学性能研究

电极材料的开发与完善是提高电容器性能的主要途径之一.本文以烟煤为炭质原料、硝酸铜为添加剂催化制备了铜/活性炭复合材料,并对氧化铜电极、活性炭电极和铜/活性炭复合材料电极进行了循环伏安、交流阻抗和电压保持能力等电化学性能测试.结果表明,活性炭中含有适量的铜可与活性炭产生协同效应,铜/炭复合材料的电容量高于纯氧化铜电极和活性炭电极的电容量之和,含铜20%的活性炭比电容量可达67.5 F/g,是同样条件制得的无铜活性炭比电容量的1.72倍;含铜活性炭具有较好的循环性能、容量特性和较小的阻抗;但其开路电压的自保持性能有待进一步改善.     

炭/多壁碳纳米管复合材料的制备与超级电容性能

结合环糊精包覆和热处理技术制备了炭/多壁碳纳米管(C/MWCNTs)复合材料, 并研究其应用于超级电容器的性能.利用扫描电子显微镜、透射电子显微镜、X射线衍射和拉曼光谱等技术对C/MWCNTs复合材料的形貌及结构进行分析.采用循环伏安和恒流充放电等电化学测试方法研究其电容特性.结果表明, C/MWCNTs复合材料具有良好的电化学性能, 远优于相应的炭及MWCNTs样品.在1 A/g电流密度下, 比电容可达到145 F/g, 循环3000次后, 容量无明显衰减.     

Development and characterization of a new conducting carbon composite electrode

A new conducting composite flexible material prepared from cellulose acetate (CA) polymer and graphite has been developed and used for the fabrication of electrodes, which were then characterized by cyclic voltammetry and electrochemical impedance spectroscopy. Scanning electron microscopy (SEM) was used to provide information concerning the morphology of the composite electrode surface. The potential window, background currents and capacitance were evaluated by cyclic voltammetry in the pH range from 4.6 to 8.2. The voltammetry of model electroactive species demonstrates a close to reversible electrochemical behaviour, under linear diffusion control. The electroactive area of the composite electrodes increases after appropriate electrode polishing and electrochemical pre-treatment. The electrodes were used as substrate for the electropolymerisation of the phenazine dye neutral red, for future use as redox mediator in electrochemical biosensors. The composite electrodes were also successfully used for the amperometric detection of ascorbate at 0.0 V vs. SCE, and applied to the measurement of ascorbate in Vitamin C tablets; the sensor exhibits high sensitivity and a low detection limit of 7.7 μM. Perspectives for use as a versatile, mechanically flexible and robust composite electrode of easily adaptable dimensions are indicated.     

Square Wave Stripping Voltammetry of Unlabeled Single‐ and Double‐Stranded DNAs

We show that, in difference to previously applied electrochemical methods working with stationary electrodes, square wave voltammetry produces well‐developed peaks II_SW (specific for dsDNA) and III_SW yielded by ssDNA at hanging mercury drop electrode (HMDE) and solid amalgam electrodes (SAEs). Using these peaks various kinds of DNA structural transitions can be studied, including unwinding of dsDNA at negatively charged electrode surfaces. The sensitivity of the DNA analysis is much better than that obtained with guanine oxidation signals at carbon electrodes. Both carbon electrodes and SAEs appear attractive as transducers in label‐free RNA and DNA sensors.     

二氧化锰含量对活性炭电极电化学性能的影响

本文采用液相法、热分解MnCO₃法以及电解沉积法制备不同二氧化锰粉末,并将其与活性炭复合,应用于水系超级电容器. 使用X射线衍射（XRD）、扫描电子显微镜（SEM）技术对材料形貌进行表征. 使用循环伏安法以及恒流充放电法对其电化学性能进行测试. 实验数据表明,α-MnO₂（质量分数70%）掺杂活性炭电极的最大比容量为151 F•g^-1,β-MnO₂（质量分数60%）掺杂活性炭电极的最大比容量为172F•g^-1,γ-MnO₂（质量分数50%）掺杂活性炭电极的最大比容量为141F•g^-1,但二氧化锰粉末对电极内阻的影响呈无规律性.     

柔性复合织物电极Graphene/Cotton和MnO2/Graphene/Cotton的合成及在电化学电容器中的应用

通过热还原法成功地制备出了柔性复合织物电极石墨烯/棉布(graphene/cotton)。热还原条件对电极的导电性能具有较大的影响。导电柔性织物电极graphene/cotton特有的多级结构使其既有利于进一步负载膺电容材料,又有利于电子和电解质离子的传输与扩散。通过电化学沉积方法,利用导电柔性织物电极graphene/cotton进一步制备出了电极MnO₂/graphene/cotton。利用扫描电子显微镜(SEM),傅里叶变换红外(FTIR)光谱,四探针测试法等表征技术对电极的结构进行了较为详细的表征。结果表明电极MnO₂/graphene/cotton的比电容可以达到536 F·g^-1。良好的电化学性能和柔性使得此类电极在柔性储能材料应用中具有极大的应用前景。     

硫化亚铁电极的电化学合成及性能测试

采用循环伏安法确定了合成硫化亚铁的电极电位,在ＬｉＣｌ－ＫＣｌ－Ｌｉ２和Ｌｉ（ＦＣｌＩ）－Ｌｉ２Ｓ两种熔体中,控制铁电极的电位为－１．０Ｖ合成了硫化亚铁电极,测试了电极的充电性能,在Ｌｉ（ＦＣｌＩ）－Ｌｉ２Ｓ熔盐２体系中电化学合成硫化亚铁电极的性能最好。     

Evaporation induced self-assembly of templated silica and organosilica thin films on various electrode surfaces

A new one-step method is reported for the deposition of hybrid mesoporous thin films on various electrode surfaces (gold, platinum, glassy carbon). Deposition was achieved by spin-coating sol–gel mixtures in the presence of a surfactant template to get mesostructured thin layers on the various conducting substrates. Film formation occurred by evaporation induced self-assembly (EISA) involving the hydrolysis and (co)condensation of silane and/or organosilane precursors on the electrode surface. Extraction of the surfactant from the ordered mesoporous films led to a large increase of mass transport rates into the materials and imparted high accessibility to the organic moieties in case of functionalized mesoporous overlayers. The electrochemical properties of the film-modified electrodes have been studied by cyclic voltammetry (CV), and also via the chemical accumulation of mercury ions prior to their stripping analysis by differential pulse voltammetry (i.e. for thiol-functionalized thin films). Some evidences to support the formation of self-assembled monolayers (SAMs) on electrodes, have been also discussed. The formation of well-adhering mesoporous thin films on solid electrode surfaces is expected to have a high impact on the development of new electrochemical sensors.     

对乙酰氨基酚在多壁碳纳米管修饰电极上的电化学行为

制备了多壁碳纳米管修饰玻碳电极,研究了对乙酰氨基酚在多壁碳纳米管修饰电极上的循环伏安行为,并建立了测定对乙酰氨基酚含量的电化学分析方法。在pH为6.89的磷酸盐缓冲液中,多壁碳纳米管修饰电极对对乙酰氨基酚有明显的电催化作用,其氧化峰电流与对乙酰氨基酚浓度在1.0×10-6～1.0×10-4mol·L-1范围内呈良好的线性关系,检测限为2.0×10-7mol·L-1。     

Direct electrodeposition of gold nanoparticles onto indium tin oxide film coated glass: Application to the detection of arsenic(III).

Gold nanoparticle modified indium tin oxide (ITO) film coated glass electrodes were prepared for the first time through direct electrochemical deposition from 0.5 M H2SO4 containing 0.1 mM HAuCl4. The resulting electrode surfaces were characterized with AFM. Cyclic voltammetry and linear sweep voltammetry (LSV) of arsenic(III) on the modified electrodes were performed. After optimization, a LOD of 5 +/- 0.2 ppb was obtained with 60 s deposition at -0.6 V (vs. SCE) in 1 M HNO3 using LSV.     

基于纳米银-石墨烯复合材料的增强效应电化学测定对乙酰氨基酚

利用氧化还原反应制备纳米银-石墨烯复合纳米材料(Ag NPs-GN),将其修饰在玻碳电极表面制备了纳米银-石墨烯修饰玻碳电极(Ag NPs-GN/GCE)。在p H 4.78的Britton-Robinson(B-R)缓冲溶液中,用循环伏安法(CV)和方波伏安法(SWV)研究了对乙酰氨基酚在Ag NPs-GN/GCE和GN/GCE上的电化学行为。结果表明,二者对对乙酰氨基酚的氧化还原反应均有电催化作用,而且复合纳米材料Ag NPs-GN具有较单一GN更好的催化效果。用方波伏安法测得对乙酰氨基酚的还原峰电流与其浓度在1.0×10-7~5.0×10-4mol/L范围内呈线性关系,检出限(S/N=3)为3.0×10-8mol/L。建立了片剂中对乙酰氨基酚含量测定的新方法,修饰电极具有较好的重现性和稳定性。     

纳米多孔结构镍基复合膜电极的电化学法制备及其电容特性

通过对电沉积法得到的Ni-Cu合金镀层进行电化学去合金化处理, 制备了纳米多孔结构金属镍膜. 采用循环伏安法对多孔金属镍膜在1 mol·L^-1 KOH溶液中进行阳极氧化处理, 获得了纳米多孔结构的镍基复合膜电极. 应用扫描电子显微镜(SEM)、X射线衍射(XRD)、X射线光电子能谱(XPS)和电化学技术对所制备的膜电极的物理性质及赝电容特性进行了表征. SEM、XRD和XPS的测试结果表明, 所制备的纳米多孔结构镍基复合膜由Ni、Ni(OH)₂和NiOOH组成. 电化学实验结果显示, 该复合膜在20 A·g^-1的充放电电流密度下, 给出了578 F·g^-1的初始比电容; 在1000次充放电循环后, 它的比电容值为544 F·g^-1, 电容保持率为94%. 纳米多孔结构有利于KOH电解液的渗透, 从而促进反应物种在电极内部的传输; 纳米多孔的金属镍基体可以提高Ni(OH)₂膜的电子导电性; 纳米大小的Ni(OH)₂颗粒能够缩短质子的固相扩散路径. 上述因素是所制备的纳米多孔结构镍基复合膜电极具有优异赝电容特性的主要原因.     

碳纳米管修饰电极同时测定邻苯二酚和对苯二酚

用十二烷基磺酸钠(SDS)分散碳纳米管(CNTs),通过层层组装(LBL)聚二甲基二烯丙基氯化铵(PDDA)和CNTs构筑PDDA/CNTs多层膜电极.利用紫外-可见光谱法对PDDA/CNTs多层膜的组装过程进行监测,用循环伏安法(CV)和差分脉冲伏安法(DPV)研究了邻苯二酚和对苯二酚同时存在时PDDA/CNTs多层膜电极上的电化学行为.结果表明,碳纳米管修饰电极对邻苯二酚和对苯二酚有较好的电催化活性和电分离作用,邻苯二酚和对苯二酚无需经过分离即可同时被检出.在修饰电极上的线性范围如下:邻苯二酚为2.0×10-6~1.4×10-4mol/L,线性相关系数R=0.9991;对苯二酚为2.0×10-6~1.4×10-4mol/L,线性相关系数R=0.9987.     

Simultaneous and Sensitive Detection of Cd(II) and Pb(II) Using a Novel Bismuth Film/Ordered Mesoporous Carbon‐molecular Wire Modified Graphite Carbon Paste Electrode

An electrochemical sensor for the simultaneous and sensitive detection of Cd(II) and Pb(II) is proposed on the basis of square‐wave anodic stripping voltammetry (SWASV) experiments using a novel bismuth film/ordered mesoporous carbon‐molecular wire modified graphite carbon paste electrode (Bi/OMC‐MW/GCPE). Ordered mesoporous carbon (OMC) and molecular wire (MW) (diphenylacetylene) were used as the modifier and binder, respectively. The Bi/OMC‐MW/GCPE was prepared with the addition of graphite powder, OMC and DPA at the ratio of 2 : 1 : 1. The electrochemical properties and morphology of the electrode were characterized by electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), SWASV and scanning electron microscopy (SEM). The parameters affecting the stripping current response were investigated and optimized. The experimental results show that the prepared electrode exhibited excellent electrochemical performance, good electrical conductivity and a high stripping voltammetric response. Under optimized conditions, a linear range was achieved over a concentration range from 1.0 to 70.0 μg/L for both Cd(II) and Pb(II) metal ions, with detection limits of 0.07 μg/L for Cd(II) and 0.08 μg/L for Pb(II) (S/N=3) with the deposition time 150 s. Moreover, the sensor exhibited improved sensitivity and reproducibility compared to traditional CPEs. The fabricated electrode was then successfully used to satisfactorily detect Cd(II) and Pb(II) in real soil samples.     

扫描电化学显微镜直接电沉积法构建葡萄糖氧化酶微米点

利用自制的凹形电极在铂基底电极上直接构建了葡萄糖氧化酶微米点. 首先, 将电聚合和电化学刻蚀法相结合制备了凹形铂微米电极. 然后将此种电极作为参比及辅助电极, 基底铂电极作为工作电极, 利用葡萄糖氧化酶在合适的条件下(浓度、一定量Triton X-100存在、电极电位等)由于电极表面pH的降低可以在铂电极上电沉积这一特性, 将酶固定在铂基底电极上, 微修饰得到了具有活性的葡萄糖氧化酶微米点. 最终用扫描电子显微镜和扫描电化学显微镜对所得微米点进行了表征. 所得微米点直径约20 μm, 且具有催化活性. 该方法简便, 干扰因素较少.     

Ordered Mesoporous Silica Incorporating Platinum Nanoparticles as Electrode Material for Paracetamol Detection

High ordered mesoporous materials (SBA-15) modified with Al and/or B and Pt nanoparticles (Pt NPs) were used for preparing modified graphite paste electrodes (Pt/M−SBA-15-GPE, where M=Al−, B− or Al−B−) and applied for paracetamol (PA) detection. The electrodes were investigated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Square wave voltammetry (SWV) technique was used to obtain the analytical parameters for PA detection. The acquired values of electrochemical and analytical parameters recommend the mesoporous compound containing Pt NPs to be used as composite electrode material for PA detection in real samples.     

Hydrogen Evolution: Electrochemical Pretreatment for Voltammetric Analysis with Gold Electrodes

A pretreatment for gold electrodes is presented in this work. The improvement of the voltammetric responses for gold surfaces is achieved applying an adequate cathodic potential in acidic media which results on vigorous evolution of gas hydrogen at the interface between electrode and electrolyte. The effectiveness of this procedure is evidenced for gold wire electrodes by cyclic voltammetry in several redox systems. The pretreatment is also compared with other activation methods for gold electrodes in electroanalytical and electrochemical terms.     

IrO2电极在4-氯苯酚水溶液中的电化学活性

研究了在4-氯苯酚(简称氯酚)电化学稳定窗口内氯酚对Ti基IrO2电极在酸性水溶液中电化学活性的影响. 循环伏安(CV)与电化学阻抗谱(EIS)测试均显示, 几乎在整个氯酚的电化学稳定电位区间内, 氯酚对氧化物电极均起到活化作用. 以金属Ir电极为对比试样的测试结果却显示, 由于氯酚易于在金属表面吸附, 氯酚在其电化学稳定窗口内对金属电极的活性产生抑制作用. 基于氯酚对上述两类电极电化学行为影响的差异, 提出活性氧化物自身在上述电位区间内发生从低价态到高价态的转变, 进而用于氧化去除吸附在电极表面的有机分子, 可能是氯酚对IrO2电极造成活化的主要原因.