Solid-phase microextraction of chlorpyrifos in fruit samples by synthesised monolithic molecularly imprinted polymer fibres

A monolithic solid-phase microextraction (SPME) fibre was fabricated based on a molecularly imprinted polymer that could be coupled with gas chromatography for extraction, and determination of chlorpyrifos. The time of extraction, pH, temperature and ionic strength were investigated as important factors on the extraction procedure. The fabricated fibre was firm, inexpensive, stable and selective which gave it vital importance in SPME. The selectivity of the fabricated fibre in relation to analogue compounds was also investigated. Under the optimum conditions, the calibration curve was linear in the range of 1–20 mg L^?1 (R² = 0.9899). The high extraction efficiency was obtained for chlorpyrifos with a detection limit of 0.23 mg L^?1. The fabricated fibre was successfully applied to SPME of chlorpyrifos from apple and grape fruits after its extraction and followed by gas chromatography-flame ionisation detector analysis.     

A Sensitive Method for Methyl tert-Butyl Ether Analysis in Water Samples by a New HS-SPME Vial and GC

In this study, a new sample vial has been designed for the extraction and determination of methyl tert-butyl ether (MTBE) in water samples by headspace solid-phase microextraction method. The special feature of this new vial is cooling the HS above the aqueous sample by cold water stream for maximum analyte absorption on SPME fiber coating. The analysis was by a gas chromatograph equipped with flame ionization detector and a capillary column (CP-sil 13 CB). Some significant variables affecting the extraction procedure were optimized. By use of divinylbenzene/carboxen/polydimethylsiloxane fiber, a sample volume of 10 mL, stirring rate of 1,000 rpm, salt concentration of 24%, extraction time of 15 min and extraction temperature of 83 °C, detection limit of 0.022 μg L⁻¹ and a good linearity (R ² = 0.998) in a calibration range of 0.1–400 μg L⁻¹ were achieved. The relative standard deviation for triplicate runs ranged between 6 and 8%. The method could be applied to the analysis of trace levels of MTBE in various water samples.

     

Synthesis and Application of High Selective Monolithic Fibers Based on Molecularly Imprinted Polymer for SPME of Trace Methamphetamine

A monolithic solid-phase microextraction (SPME) fiber was fabricated based on a molecularly imprinted polymer which could be coupled with gas chromatography for extraction, pre-concentration and determination of methamphetamine (MAMP). Methacrylic acid, ethylene glycol dimethacrylate and MAMP play the roles of functional monomer, cross-linker and template, respectively. The effective factors influencing the polymerization and extraction procedures were investigated and will be detailed here. The fabricated fiber was firm, inexpensive, stable, selective and durable which gives it vital importance in SPME. Selectivity of the fabricated fiber in relation to the template in solution containing MAMP, related and unrelated compounds was also investigated. Under the optimum conditions, the calibration plot was linear in the range of 50?C3,500 ng mL^?1 (r ²  = 0.997). The high extraction efficiency was obtained for MAMP giving a detection limit of 14 ng mL^?1. The fabricated fiber was successfully applied to SPME of MAMP from human saliva samples followed by gas chromatography-flame ionization detector analysis.     

A Hexagonally Ordered Nanoporous Silica-Based Fiber Coating for SPME of Polycyclic Aromatic Hydrocarbons from Water Followed by GC–MS

A highly porous fiber coating material was prepared and functionalized with 3-amino propyl triethoxysilane (APTES) on hexagonally ordered nanoporous silica (SBA-15). Applicability of this coating was assessed employing a laboratory made solid-phase microextraction (SPME) device and gas chromatography–mass spectrometry for the simultaneous sampling and determination of trace polycyclic aromatic hydrocarbons (PAHs) from aqueous sample solutions. A one at the time optimization strategy was applied to investigate and optimize important extraction parameters such as extraction temperature, extraction time, ionic strength and sonication time. In the optimum conditions, the relative standard deviations for deionized water, spiked with selected PAHs were between 3.3 and 7.7% (n = 3), and detection limits for the studied compounds were 4.2 and 26.1 pg mL⁻¹. No significant change was observed in the extraction efficiency of the new SPME fiber, over 50 extractions. The proposed method was successfully applied to the extraction and determination of PAHs in the waste water samples.

     

A highly thermal-resistant electrospun-based polyetherimide nanofibers coating for solid-phase microextraction

A high-temperature-resistant solid-phase microextraction (SPME) fiber was prepared based on polyetherimide (PEI) by the electrospinning method. The PEI polymeric solution was converted to nanofibers using high voltages and directly coated on a stainless steel SPME needle. The scanning electron microscopy images of PEI coating showed fibers with diameter range of 500–650 nm with a homogeneous and smooth surface morphology. The SPME nanofibers coating was optimized for PEI percentage, electrospinning voltage, and time. The extraction efficiency of the coating was investigated for headspace SPME of some environmentally important polycyclic aromatic hydrocarbons from aqueous samples followed by gas chromatography–mass spectrometry measurement. In addition, the important extraction parameters including extraction temperature, extraction time, ionic strength, as well as desorption temperature and time were investigated and optimized. The detection limits of the method under optimized conditions ranged from 1 to 5 ng L^?1 using time-scheduled selected ion monitoring mode. The relative standard deviations of the method were between 1.1 and 7.1 %, at a concentration level of 500 ng L^?1. The calibration curves of polycyclic aromatic hydrocarbons showed linearity in the range of 5–1000 ng L^?1. The developed method was successfully applied to real water samples and the relative recovery percentages obtained from the spiked water samples were from 84 to 98 % for all the selected analytes except for acenaphthene which was from 75 to 106 %.     

Electrophoretic deposition of polyaniline nanofibers on a stainless steel wire as an adsorbent for determination of tamoxifen by SPME/GC–FID in urine samples

Polyaniline nanofiber films were fabricated on the surface of stainless steel wire via a controllable and simple electrophoretic deposition route from a nonaqueous colloidal suspension consisting of polyaniline nanofibers. The prepared coating material was then characterized by field emission scanning electron microscopy equipped with energy dispersive spectroscopy and elemental mapping analysis. The fabricated polyaniline film-coated stainless steel wire was then utilized as an effective and novel sorbent phase for solid-phase microextraction of tamoxifen for subsequent gas chromatography/flame ionization detection of this anticancer drug. Parameters consisting of the temperature, extraction time, salt concentration, agitation speed, pH, temperature and time of desorption were studied and optimized using a one-at-a-time strategy. Under the optimum conditions, detection limit (S/N = 3), the limit of quantification (10/3 limit of detection), linear dynamic range, repeatability and reproducibility values of 0.51 μg L⁻¹, 1.7 μg L⁻¹, 2–1,130 μg L⁻¹, 5.7% and 8.6% were attained, respectively. The prepared fiber can preserve 90% of its efficacy after 20 consecutive cycles, demonstrating the suitable thermal stability and cyclability of the proposed solid-phase microextraction coating material for the determination of tamoxifen by gas chromatography/flame ionization detection. The route was effectively utilized to determine tamoxifen in urine samples, with relative recoveries ranging from 89 to 106%.     

Solid-phase microextraction using a diglycidyloxycalix[4]arene coated fiber combined with gas chromatography: very simple, rapid and sensitive method for the determination of chlorobenzenes in water

A fiber material for solid-phase microextraction (SPME) was obtained by blending 5,11,17,23-tetra-tert-butyl-25,27-dihydroxy-26,28-diglycidyloxycalix[4]arene with hydroxy-terminated silicone oil by sol-gel technology. It was used for headspace SPME combined with gas chromatography using electron capture detection to determine seven chlorobenzenes in water matrix. Optimum extraction conditions were 15 min at 20 °C with a solution containing 300 g L^?1 sodium chloride. The fiber exhibits far higher extraction efficiency than the commercially available poly(dimethylsiloxane) (PDMS) and PDMS-divinylbenzene fibers. The detection limits range from 0.32 to 2.25 ng L^?1, and the relative standard deviations are <5%. The calibration curves display a high level of linearity, with correlation coefficients ranging between 0.9996 and 1. The method was applied to analyze a lake water sample that was found to be polluted with 1,2,3,4-tetrachlorobenzene and hexachlorobenzene. It was compared to the United States Environmental Protection Agency method and other recently introduced methods. The results demonstrate that the technique is rapid, simple, and sensitive, and thus represents an attractive alternative for ultra-trace analysis of chlorobenzenes in water samples.     

A Sensitive Method for the Determination of Methadone in Biological Samples Using Nano-Structured α-Carboxy Polypyrrol as a Sorbent of SPME

Nano-structured α-carboxy polypyrrol (PPy- α-COOH) was used as a coating of solid-phase microextraction (SPME) fiber to increase the extraction efficiency of headspace solid phase microextraction (HS-SPME) of methadone (MDN) in biological samples. The carboxy-endcapped polypyrrole film was prepared via electrochemical deposition on a platinum wire. A nano-fibrous structure of PPy-α-COOH with a diameter of 120 nm was obtained. The porous surface structure of the film, revealed by scanning electron microscopy, provided high surface areas and allowed for high extraction efficiency of methadone. Then the analysis of the extracts was carried out by a gas chromatography-flame ionization detector. In order to achieve maximum extraction efficiency, different parameters affecting the extraction conditions were optimized. Under the optimized conditions, the limit of detections and the limit of quantifications of the method in the range of 0.02–0.035 and 0.06–0.10 μg L⁻¹ were obtained for different matrices. The relative recoveries in different samples were in the range of 95–97%. Finally, the feasibility of the proposed method was successfully confirmed by extraction and determination of MDN in human urine and plasma samples in the range of microgram per liter, and suitable results were obtained (RSDs <5.3%).

     

A Sensitive Method for Methyl tert-Butyl Ether Analysis in Water Samples by a New HS-SPME Vial and GC

In this study, a new sample vial has been designed for the extraction and determination of methyl tert-butyl ether (MTBE) in water samples by headspace solid-phase microextraction method. The special feature of this new vial is cooling the HS above the aqueous sample by cold water stream for maximum analyte absorption on SPME fiber coating. The analysis was by a gas chromatograph equipped with flame ionization detector and a capillary column (CP-sil 13 CB). Some significant variables affecting the extraction procedure were optimized. By use of divinylbenzene/carboxen/polydimethylsiloxane fiber, a sample volume of 10 mL, stirring rate of 1,000 rpm, salt concentration of 24%, extraction time of 15 min and extraction temperature of 83 °C, detection limit of 0.022 μg L^?1 and a good linearity (R ² = 0.998) in a calibration range of 0.1–400 μg L^?1 were achieved. The relative standard deviation for triplicate runs ranged between 6 and 8%. The method could be applied to the analysis of trace levels of MTBE in various water samples.     

Determination of Racemic Ketorolac,Ketorolac Enantiomers and Their Metabolites in Human Plasma and Urine by LC–UV,Applied in Clinical Study During and After Pregnancy

In order to enhance the sensitivity and to develop a faster direct method for plasma and urine quantification of racemic ketorolac, its metabolites (p-hydroxy-ketorolac and ketorolac glucuronides) and ketorolac enantiomers, we developed an extraction procedure based on solid-phase extraction combined with specific and fast chromatographic separation. Extraction and chromatography resulted in cleaner chromatograms without interfering compounds. In both plasma and urine, linearity of the standard curves for racemic ketorolac and p-hydroxy-ketorolac was validated in the concentration range 0.025–10 mg L⁻¹, while for ketorolac enantiomers in the concentration range 0.025–5 mg L⁻¹. The lower limit of quantification was two times lower than in earlier described methods. The developed method was suitable for direct quantification of racemic ketorolac, p-hydroxy-ketorolac and ketorolac enantiomers in plasma and urine samples in women at delivery and in postpartum, enabling us to document significant intra-individual differences in pharmacokinetics between these physiological states.

     

Porous carbon derived from aluminum-based metal organic framework as a fiber coating for the solid-phase microextraction of polycyclic aromatic hydrocarbons from water and soil

A nanoporous carbon derived from an aluminum-based metal-organic framework was deposited on stainless steel wires in a sol–gel matrix. The resulting fibers were applied to the solid-phase microextraction of the polycyclic aromatic hydrocarbons (PAHs) naphthalene, acenaphthene, fluorene, phenanthrene and anthracene from water and soil samples. The fiber was then directly inserted into the GC injector and the PAHs were quantified by GC-MS. The effects of salt addition, extraction temperature, extraction time, sample volume and desorption conditions on the extraction efficiency were optimized. A linear response to the analytes was observed in the 0.1 to 12 μg∙L⁻¹ range for water samples, and in the 0.6 to 30 μg∙kg⁻¹ for soil samples, with the correlation coefficients ranging from 0.9934 to 0.9985. The limits of detection ranged from 5.0 to 20 ng∙L⁻¹ for water samples, and from 30 to 90 ng∙kg⁻¹ for soil samples. The recoveries of spiked samples were between 72.4 and 108.0 %, and the precision, expressed as the relative standard deviations, is <12.8 %.

A MOF derived nanoporous carbon coated fiber for use in solid-phase microextraction was prepared via sol–gel technology. The coated fiber has a porous, rough and wrinkled structure, and shows a high thermal stability, good extraction repeatability and long lifetime. The established HS-SPME-GC-MS method is suitable for the determination of the PAHs from water and soil samples.

     

A Hexagonally Ordered Nanoporous Silica-Based Fiber Coating for SPME of Polycyclic Aromatic Hydrocarbons from Water Followed by GC�CMS

A highly porous fiber coating material was prepared and functionalized with 3-amino propyl triethoxysilane (APTES) on hexagonally ordered nanoporous silica (SBA-15). Applicability of this coating was assessed employing a laboratory made solid-phase microextraction (SPME) device and gas chromatography?Cmass spectrometry for the simultaneous sampling and determination of trace polycyclic aromatic hydrocarbons (PAHs) from aqueous sample solutions. A one at the time optimization strategy was applied to investigate and optimize important extraction parameters such as extraction temperature, extraction time, ionic strength and sonication time. In the optimum conditions, the relative standard deviations for deionized water, spiked with selected PAHs were between 3.3 and 7.7% (n = 3), and detection limits for the studied compounds were 4.2 and 26.1 pg mL^?1. No significant change was observed in the extraction efficiency of the new SPME fiber, over 50 extractions. The proposed method was successfully applied to the extraction and determination of PAHs in the waste water samples.     

Preparation of a Robust and Sensitive Gold-Coated Fiber for Solid-Phase Microextraction of Polycyclic Aromatic Hydrocarbons in Environmental Waters

A robust gold-coated solid-phase microextraction fiber was rapidly prepared on an etched stainless-steel wire based on chemical deposition. Gold(III) was reduced to produce a mechanically robust fiber with a stable coating. Subsequently, it was applied for solid-phase microextraction of five polycyclic aromatic hydrocarbons in water samples coupled to high performance liquid chromatography with an ultraviolet-visible detector. The preconcentration conditions were optimized, including extraction and desorption time, temperature, stirring rate, and ionic strength. Under the optimized conditions, the calibration graphs were linear in the range from 1 to 500 µg · L^?1 for naphthalene and 0.20–500 µg · L^?1 for phenanthrene, anthracene, fluoranthene, and pyrene. Limits of detection were between 0.016 and 0.22 µg · L^?1 (signal-to-noise ratio = 3). The analysis of water samples showed that the recoveries ranged from 86.0% to 112.9% with relative standard deviations between 2.03% and 11.7%. The fiber coating was sensitive and suitable for the preconcentration and determination of polycyclic aromatic hydrocarbons in environmental waters. Compared with previously reported solid-phase microextraction methods, this device offered easy preparation, low cost, resistance to organic solvents, good stability, and high durability.     

Headspace solid-phase microextraction of menthol using a sol–gel titania-based coating along with multiwalled carbon nanotubes on the surface of stainless steel fiber

Sol–gel coating technology for the preparation of solid-phase microextraction fibers involves a single-step procedure and allows for in situ creation of chemically bonded coatings which are characterized by high thermal and solvent stabilities. A novel titania sol–gel coating was prepared for the first time on a stainless steel fiber and applied for the headspace solid-phase microextraction (HS-SPME) of menthol with gas chromatography and flame ionization detection. Important parameters influencing the efficiency of SPME process, such as extraction time, extraction temperature and ionic strength, were optimized by central composite design. An extraction time of 40 min at 60 °C gave maximum extraction efficiency, when NaCl (10% w/v) was added to the aqueous sample. The analytical characteristics of the proposed method were comparable with other reported fibers. Under optimized conditions, the linearity was between 0.05 and 100 µg mL^??1. The relative standard deviations (RSDs) determined at 0.5 µg mL^??1 concentration level (n?=?5) were as follows: intra-day RSD 7.26%; inter-day RSD 10.87%; fiber-to-fiber RSD 9.05%. The relative recoveries determined after spiking a mint distillate sample at three concentration levels from 0.067 to 50.0 µg mL^??1 varied from 86 to 102%. The proposed method was successfully applied for the analysis of menthol in peppermint samples.     

Bamboo charcoal as a novel solid-phase microextraction coating material for enrichment and determination of eleven phthalate esters in environmental water samples

This study demonstrates the potential of bamboo charcoal as a novel and inexpensive solid-phase microextraction (SPME) coating material for enrichment and determination of organic pollutants in water samples. Bamboo charcoal was prepared and used as a SPME coating material. Eleven phthalate esters (PAEs) were used as model analytes, and gas chromatography–mass spectrometry was used for separation and detection. Important extraction conditions (ionic strength, stirring rate, and extraction time) and desorption conditions (desorption temperature and time) were systematically investigated and optimized. Linearity of 0.1–100 μg?L^?1 and correlation coefficients of 0.9992–0.9998 were obtained under optimum conditions. Inter-day and intra-day repeatability were 2.15–9.93 % and 1.89–9.85 %, respectively, and fiber-to-fiber reproducibility was 5.42–9.66 %. On the basis of a chromatographic signal-to-baseline noise ratio of three, the limits of detection reached 0.004–0.023 μg?L^?1. Satisfactory results were achieved when the bamboo coating was used for determination of 11 PAEs in real water samples. The experimental results indicate that bamboo charcoal has significant potential as a SPME coating material for rapid enrichment and sensitive determination of organic pollutants in environmental samples.     

Determination of Herbicide Residues in Garlic by GC–MS

A rapid multi-residue method has been developed for the determination of 16 herbicides in garlic. The analytical procedure is based on prior microwave heating prevention of the generation of sulfur-containing compounds. The garlic samples which had been pretreated were extracted with acetonitrile and cleaned up by solid-phase extraction. The herbicide residues were detected by gas chromatography–mass spectrometry with selected ion monitoring. The recoveries of 16 herbicides ranged from 69.0 to 105.4% with the relative standard deviations (RSD) below 10.1%. The limit of quantification (LOQ) ranged from 0.003 to 0.015 mg kg⁻¹.

     

MultiSimplex optimization of the dispersive solid-phase microextraction and determination of fenitrothion by magnetic molecularly imprinted polymer and high-performance liquid chromatography

A magnetic molecularly imprinted polymer (MMIP) was fabricated and used as the sorbent for the MMIP-dispersive solid-phase microextraction of fenitrothion prior its determination by high-performance liquid chromatography equipped with an ultraviolet detector. The MMIP was prepared using functionalized Fe₃O₄ nanoparticles as the magnetic supporter. Methacrylic acid, ethylene glycol dimethacrylate and fenitrothion were used as the functional monomer, the cross-linker and the template, respectively. The properties of the resultant MMIP were evaluated using X-ray diffraction spectroscopy, Fourier transform infrared spectroscopy and scanning electron microscopy. The sorbent exhibited high selectivity and affinity toward fenitrothion compared to other organophosphate pesticides with the maximum adsorption capacity of 31.5 mg g^?1. The effective variables on the extraction were optimized by univariable and MultiSimplex methods. The calibration curve exhibited linearity over the concentration range of 0.3–50.0 μg L^?1 with the limit of detection of 0.1 μg L^?1. The relative standard deviations at 10.0 μg L^?1 level of FNT (n = 5) for intra- and inter-day assays were 1.6 and 3.1%, respectively. The proposed method was successfully used for the determination of trace amounts of FNT in food and water samples.     

A Novel Fiber with Phenyl-Functionalized MSU (Michigan State University) Coating for Solid-Phase Microextraction Combined with High Performance Liquid Chromatography for Preconcentration and Determination of Trace Polychlorinated Biphenyls in Environmental Water Samples

A novel and robust phenyl-functionalized MSU-1 (Ph-MSU) coated fiber for solid-phase microextraction (SPME) coupled to high performance liquid chromatography (HPLC) was developed for the preconcentration and the determination of 2,4,4′-trichlorobiphenyl (PCB 28), 2,4′,5-trichlorobiphenyl (PCB 31), 2,2′,5,5′-tetrachlorobiphenyl (PCB 52), 2,2′,4,5,5′-pentachlorobiphenyl (PCB 101), 2,3′,4,4′,5-pentachlorobiphenyl (PCB 118), 2,2′,3,4,4′,5′-hexachlorobiphenyl (PCB 138), 2,2′,4,4′,5,5′-hexachlorobiphenyl (PCB 153), and 2,2′,3,4,4′,5,5′-heptachlorobiphenyl (PCB 180) in environmental water samples. Experimental conditions affecting SPME were examined in detail. The Ph-MSU coating provided large porosity and short-range mesostructures necessary for high extraction capacity and rapid mass transfer of PCBs. The Ph-MSU coated fiber exhibited selectivity for PCB 28, PCB 31, PCB 118, and PCB 138 in a limited extraction time. Good linearity for all PCBs was obtained with correlation coefficients from 0.9987 to 0.9994. The recoveries were within 94.3% to 103% for the spiked water with 300 ng · L^?1 per PCB. The relative standard deviations (RSDs) ranged from 3.10% to 6.23% and the limits of detection (LODs) were between 8.73 ng · L^?1 and 13.8 ng · L^?1. The proposed method was applied for the determination of PCBs in real river water and rainwater samples. The median recoveries ranged from 85.6% to 118% with RSDs between 4.23% and 8.78%. The experimental results demonstrated that the Ph-MSU fiber coating could be reused for over 250 times without loss of the extraction efficiency. These results clearly indicate that the Ph-MSU coated fiber was rapid, sensitive, and suitable for the preconcentration and determination of trace PCBs in environmental water samples.     

Hollow-Fiber-Based LPME as a Reliable Sampling Method for Gas-Chromatographic Determination of Pharmacokinetic Parameters of Valproic Acid in Rat Plasma

A sensitive and simple method based on two-phase liquid-phase microextraction in porous hollow fiber followed by gas chromatography-flame ionization detection was developed for quantification and pharmacokinetic study of valproic acid (VPA, an antiepileptic drug) in rat plasma after oral administration of pure sodium valproate (25 mg kg⁻¹). Some parameters such as type of organic solvent, pH of sample solution, stirring speed, salt addition, extraction time, and volume of sample that affected extraction efficiency of VPA were optimized. Under optimized microextraction conditions, VPA was extracted with 10 μL 1-octanol from 0.5 mL rat plasma previously diluted with 4.5 mL acidified and salinated water (pH 2) using 1-octanoic acid as internal standard. The limit of detection was 17 ng mL⁻¹ with linear response over the concentration range of 50–10,000 ng mL⁻¹ with correlation coefficient higher than 0.998. The developed method was successfully applied to determination of pharmacokinetic parameters such as t _max (peak time in concentration–time profile), C _max (peak concentration in concentration–time profile), t _1/2 (elimination half-life), AUC_0–t (area under the curve for concentration versus time), clearance, and apparent distribution volume in rats following oral administration of VPA.

     

Hydroxyundecanethiol-Modified Steel Fibers for the Selective Solid-Phase Microextraction of Polycyclic Aromatic Hydrocarbons from River and Wastewater

A novel organic–inorganic composite-coated fiber was developed for selective solid-phase microextraction (SPME) by direct electrodeposition of zinc oxide microparticles on a pretreated stainless steel wire followed by self-assembly of hydroxyundecanethiol with zinc–sulfur bonds. The performance of the hydroxyundecyl-modified zinc oxide-coated steel fiber was then assessed for SPME of polar aromatic compounds coupled to high-performance liquid chromatography with ultraviolet detection. Excellent extraction and selectivity were obtained for polycyclic aromatic hydrocarbons. The extraction and desorption times, temperature, stirring rate, and ionic strength were optimized. The limits of detection were from 0.034 to 0.132?µg?L^?1. The relative standard deviations were from 3.4 to 4.9% for a single fiber and from 5.1 to 6.4% for multiple fibers. The recovery of polycyclic aromatic hydrocarbons in environmental water fortified at 5.0 and 50?µg?L^?1 was from 83.1 to 103% with relative standard deviations below 8.4%. This fiber was shown to withstand at least 200 extraction and desorption cycles. The method was used for the preconcentration and determination of polycyclic aromatic hydrocarbons in environmental water.