Synthesis and electrochemical properties of Li-rich Li[Ni<Subscript>0.5</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.3</Subscript>]O<Subscript>2</Subscript> for pouch-typed cell

Layered transition metal oxide LiNi _x Co _y MnzO₂ cathode materials with different Li amount were successfully synthesized via co-precipitation method. Monodispersed Li[Ni_0.5Co_0.2Mn_0.3]O₂ and Li-rich Li_1.1[Ni_0.5Co_0.2Mn_0.3]O₂ spherical agglomeration consisted of secondary particles, which is favorable for the higher tap-density of materials, can be easily obtained. The pouch-typed cells with obtained materials were assembled to investigate electrochemical performance at level of full-cell. The results show that the assembled pouch-typed full-cells with Li-rich sample present higher capacity, better rate capability and cycle life.     

Quantifying Degradation Parameters of Single-Crystalline Ni-Rich Cathodes in Lithium-Ion Batteries

Single-crystal LiNi_xCo_yMn_zO₂ (SC-NCM, x+y+z=1) cathodes are renowned for their high structural stability and reduced accumulation of adverse side products during long-term cycling. While advances have been made using SC-NCM cathode materials, careful studies of cathode degradation mechanisms are scarce. Herein, we employed quasi single-crystalline LiNi_0.65Co_0.15Mn_0.20O₂ (SC-NCM65) to test the relationship between cycling performance and material degradation for different charge cutoff potentials. The Li/SC-NCM65 cells showed >77 % capacity retention below 4.6 V vs. Li⁺/Li after 400 cycles and revealed a significant decay to 56 % for 4.7 V cutoff. We demonstrate that the SC-NCM65 degradation is due to accumulation of rock-salt (NiO) species at the particle surface rather than intragranular cracking or side reactions with the electrolyte. The NiO-type layer formation is also responsible for the strongly increased impedance and transition-metal dissolution. Notably, the capacity loss is found to have a linear relationship with the thickness of the rock-salt surface layer. Density functional theory and COMSOL Multiphysics modeling analysis further indicate that the charge-transfer kinetics is decisive, as the lower lithium diffusivity of the NiO phase hinders charge transport from the surface to the bulk.     

Suppressing Universal Cathode Crossover in High-Energy Lithium Metal Batteries via a Versatile Interlayer Design**

The universal cathode crossover such as chemical and oxygen has been significantly overlooked in lithium metal batteries using high-energy cathodes which leads to severe capacity degradation and raises serious safety concerns. Herein, a versatile and thin (≈25 μm) interlayer composed of multifunctional active sites was developed to simultaneously regulate the Li deposition process and suppress the cathode crossover. The as-induced dual-gradient solid-electrolyte interphase combined with abundant lithiophilic sites enable stable Li stripping/plating process even under high current density of 10 mA cm⁻². Moreover, X-ray photoelectron spectroscopy and synchrotron X-ray experiments revealed that N-rich framework and CoZn dual active sites can effectively mitigate the undesired cathode crossover, hence significantly minimizing Li corrosion. Therefore, assembled lithium metal cells using various high-energy cathode materials including LiNi_0.7Mn_0.2Co_0.1O₂, Li_1.2Co_0.1Mn_0.55Ni_0.15O₂, and sulfur demonstrate significantly improved cycling stability with high cathode loading.     

流变相法合成LiNi0.85Co0.15O2的结构与电化学性能

以一种新型的软化学方法——流变相法, 成功地合成了锂离子电池正极材料LiNi_0.85Co_0.15O₂. 将在600～850 ℃氧气氛下处理6 h后得到的LiNi_1－yCo_yO₂ (y＝0.10, 0.15, 0.20, 0.25), 进行X射线粉末衍射(XRD)与电化学测试. 测试结果表明, 流变相前体经过800 ℃烧结后合成的LiNi_0.85Co_0.15O₂晶胞参数a＝0.2866 nm, c＝1.4193 nm及晶胞体积V＝0.1010 nm³, 以0.1 C倍率在3.0～4.3 V (vs. Li^＋/Li)放电时, 首次放电容量可以达到198.2 mAh/g, 20次循环后, 其放电容量仍在174 mAh/g以上.     

Direct Observation of Defect-Aided Structural Evolution in a Nickel-Rich Layered Cathode

Ni-rich LiNi_1−x−yMn_xCo_yO₂ (NMC) layered compounds are the dominant cathode for lithium ion batteries. The role of crystallographic defects on structure evolution and performance degradation during electrochemical cycling is not yet fully understood. Here, we investigated the structural evolution of a Ni-rich NMC cathode in a solid-state cell by in situ transmission electron microscopy. Antiphase boundary (APB) and twin boundary (TB) separating layered phases played an important role on phase change. Upon Li depletion, the APB extended across the layered structure, while Li/transition metal (TM) ion mixing in the layered phases was detected to induce the rock-salt phase formation along the coherent TB. According to DFT calculations, Li/TM mixing and phase transition were aided by the low diffusion barriers of TM ions at planar defects. This work reveals the dynamical scenario of secondary phase evolution, helping unveil the origin of performance fading in Ni-rich NMC.     

LixNi0.5Co0.5O2的态密度计算及电化学性能研究

>为获得综合性能更好的锂离子二次电池正极材料, 分析了Co掺杂对Li_xNiO₂电化学性能的影响. 采用密度泛函DFT理论对Li_xNiO₂和Li_xNi_0.5Co_0.5O₂的平均放电电压和态密度进行了计算. 同时, 用共沉淀法制备了Li_xNiO₂和Li_xNi_0.5Co_0.5O₂锂离子二次电池正极材料, 并对其进行了XRD结构分析和恒流充放电测试. 实验和计算结果表明: 随锂离子嵌入正极(电池放电), 电池的电压逐渐降低, 材料的态密度峰向低能量方向移动; 与Li_xNiO₂相比, Li_xNi_0.5Co_0.5O₂的电压平台相对较高(当0.25≤x≤0.5), 而且在Li^＋嵌/脱时, Li_xNi_0.5Co_0.5O₂的结构变化相对较小; Co离子的掺入, 减小了NiO₆八面体的畸变度, 使材料的电化学稳定性得以提高. 在钴掺杂镍酸锂体系中, NiO₆和CoO₆具有相互的稳定作用.     

Recycling Valuable Metals from Spent Lithium-Ion Batteries Using Carbothermal Shock Method

Pyrometallurgy technique is usually applied as a pretreatment to enhance the leaching efficiencies in the hydrometallurgy process for recovering valuable metals from spent lithium-ion batteries. However, traditional pyrometallurgy processes are energy and time consuming. Here, we report a carbothermal shock (CTS) method for reducing LiNi_0.3Co_0.2Mn_0.5O₂ (NCM325) cathode materials with uniform temperature distribution, high heating and cooling rates, high temperatures, and ultrafast reaction times. Li can be selectively leached through water leaching after CTS process with an efficiency of >90 %. Ni, Co, and Mn are recovered by dilute acid leaching with efficiencies >98 %. The CTS reduction strategy is feasible for various spent cathode materials, including NCM111, NCM523, NCM622, NCM811, LiCoO₂, and LiMn₂O₄. The CTS process, with its low energy consumption and potential scale application, provides an efficient and environmentally friendly way for recovering spent lithium-ion batteries.     

Synthesis and electrochemical properties of Ca-doped LiNi<Subscript>0.8</Subscript>Co<Subscript>0.2</Subscript>O<Subscript>2</Subscript> cathode material for lithium ion battery

LiNi_0.8Co_0.2O₂ and Ca-doped LiNi_0.8Co_0.2O₂ cathode materials have been synthesized via a rheological phase reaction method. X-ray diffraction studies show that the Ca-doped material, and also the discharged electrode, maintains a hexagonal structure even when cycled in the range of 3.0–4.35 V (vs Li⁺/Li) after 100 cycles. Electrochemical tests show that Ca doping significantly improves the reversible capacity and cyclability. The improvement is attributed to the formation of defects caused by the partial occupancy of Ca²⁺ ions in lithium lattice sites, which reduce the resistance and thus improve the electrochemical properties.     

Emerging Lithiated Organic Cathode Materials for Lithium-Ion Full Batteries

Organic electrode materials have application potential in lithium batteries owing to their high capacity, abundant resources, and structural designability. However, most reported organic cathodes are at oxidized states (namely unlithiated compounds) and thus need to couple with Li-rich anodes. In contrast, lithiated organic cathode materials could act as a Li reservoir and match with Li-free anodes such as graphite, showing great promise for practical full-battery applications. Here we summarize the synthesis, stability, and battery applications of lithiated organic cathode materials, including synthetic methods, stability against O₂ and H₂O in air, and strategies to improve comprehensive electrochemical performance. Future research should be focused on new redox chemistries and the construction of full batteries with lithiated organic cathodes and commercial anodes under practical conditions. This Minireview will encourage more efforts on lithiated organic cathode materials and finally promote their commercialization.     

锂离子电池富锂层状正极材料的表面改性及电化学性能

采用一种简单、实用的“浸润-泥化-干燥”结合固相烧结工艺对富锂层状正极材料Li_1.2Mn_0.54Ni_0.13Co_0.13O₂进行表面改性。这种表面改性的正极材料具有280 mAh·g^-1以上的高比容量,在0.5C下历经70周充放电循环后容量保持率达91.6%,与本体材料相比,表现出较优的循环稳定性。     

Recent advances in layered LiNi x CoyMn1−x−y O2 cathode materials for lithium ion batteries

Lithium cobalt oxide, LiCoO₂, has been the most widely used cathode material in commercial lithium ion batteries. Nevertheless, cobalt has economic and environmental problems that leave the door open to exploit alternative cathode materials, among which LiNi _x Co_yMn_{1 − x − y} O₂ may have improved performances, such as thermal stability, due to the synergistic effect of the three ions. Recently, intensive effort has been directed towards the development of LiNi _x Co _y Mn_{1 − x − y} O₂ as a possible replacement for LiCoO₂. Recent advances in layered LiNi _x Co_yMn_{1 − x − y} O₂ cathode materials are summarized in this paper. The preparation and the performance are reviewed, and the future promising cathode materials are also prospected.     

Li4Mn5O12包覆对三元正极材料结构和性能的影响

LiNi_1/3Mn_1/3Co_1/3O₂具有很高的理论比容量,但是三元正极材料在高电压下长循环时,其表面结构发生较大的衰退,导致电池的循环性能和倍率性能变差。本文采用耐高电压且结构稳定的富锂尖晶石Li₄Mn₅O₁₂包覆LiNi_1/3Mn_1/3Co_1/3O₂可以有效改善材料的电化学性能。通过XRD、SEM、XPS和TEM等手段对包覆后的材料进行分析,证实了在LiNi_1/3Mn_1/3Co_1/3O₂的表面形成了10nm厚的均匀Li₄Mn₅O₁₂的包覆层;在循环100圈后,包覆后的LiNi_1/3Mn_1/3Co_1/3O₂仍...     

Armor-like Inorganic-rich Cathode Electrolyte Interphase Enabled by the Pentafluorophenylboronic Acid Additive for High-voltage Li||NCM622 Batteries

Lithium metal batteries (LMBs) comprising Li metal anode and high-voltage nickel-rich cathode could potentially realize high capacity and power density. However, suitable electrolytes to tolerate the oxidation on the cathode at high cut-off voltage are urgently needed. Herein, we present an armor-like inorganic-rich cathode electrolyte interphase (CEI) strategy for exploring oxidation-resistant electrolytes for sustaining 4.8 V Li||LiNi_0.6Co_0.2Mn_0.2O₂ (NCM622) batteries with pentafluorophenylboronic acid (PFPBA) as the additive. In such CEI, the armored lithium borate surrounded by CEI up-layer represses the dissolution of inner CEI moieties and also improves the Li⁺ conductivity of CEI while abundant LiF is distributed over whole CEI to enhance the mechanical stability and Li⁺ conductivity compared with polymer moieties. With such robust Li⁺ conductive CEI, the Li||NCM622 battery delivered excellent stability at 4.6 V cut-off voltage with 91.2 % capacity retention after 400 cycles. The excellent cycling performance was also obtained even at 4.8 V cut-off voltage.     

Studies of LiNi0.6Co0.4O2 Cathode Material Prepared by the Citric Acid-Assisted Sol-Gel Method for Lithium Batteries

The layered LiNi_0.6Co_0.4O₂ powders were synthesized at low temperature by a sol-gel method using citric acid as a chelating agent. Submicron-sized particles of the precursor were obtained at temperature below 400°C and microcrystalline powders were grown by thermal treatment at 700°C for 4 h in air. The carboxylic-based acid acted such as a fuel, decomposed the homogeneous precipitate of metal complexes at low temperature, and yielded the free impurity LiNi_0.6Co_0.4O₂ single-phase suitable for electrochemical application. The synthesized products have been characterized by structural (XRD, SEM), spectroscopic (FTIR, Raman) and thermal (DTA/TG) analyses. Raman and FTIR measurements provide information on the local environment of the cationic sublattice of LiNi_0.6Co_0.4O₂ solid solution. Electrochemical performance of the synthesized products in rechargeable Li cells were evaluated by employing as cathodes in non-aqueous organic electrolyte mixture of 1M LiPF₆ in EC + DMC. The electrochemical behaviour of synthesized LiNi_0.6Co_0.4O₂ is discussed in relation with its synthesis procedure.     

Lithium Nitrate Regulated Sulfone Electrolytes for Lithium Metal Batteries

The electrolytes in lithium metal batteries have to be compatible with both lithium metal anodes and high voltage cathodes, and can be regulated by manipulating the solvation structure. Herein, to enhance the electrolyte stability, lithium nitrate (LiNO₃) and 1,1,2,2-tetrafuoroethyl-2′,2′,2′-trifuoroethyl(HFE) are introduced into the high-concentration sulfolane electrolyte to suppress Li dendrite growth and achieve a high Coulombic efficiency of >99 % for both the Li anode and LiNi_0.8Mn_0.1Co_0.1O₂ (NMC811) cathodes. Molecular dynamics simulations show that NO₃⁻ participates in the solvation sheath of lithium ions enabling more bis(trifluoromethanesulfonyl)imide anion (TFSI⁻) to coordinate with Li⁺ ions. Therefore, a robust LiN_xO_y−LiF-rich solid electrolyte interface (SEI) is formed on the Li surface, suppressing Li dendrite growth. The LiNO₃-containing sulfolane electrolyte can also support the highly aggressive LiNi_0.8Mn_0.1Co_0.1O₂ (NMC811) cathode, delivering a discharge capacity of 190.4 mAh g⁻¹ at 0.5 C for 200 cycles with a capacity retention rate of 99.5 %.     

An Approach towards Synthesis of Nanoarchitectured LiNi1/3Co1/3Mn1/3O2 Cathode Material for Lithium Ion Batteries

To explore advanced cathode materials for lithium ion batteries (LIBs), a nanoarchitectured LiNi_1/3Co_1/3Mn_1/3O₂ (LNCM) material is developed using a modified carbonate coprecipitation method in combination with a vacuum distillation‐crystallisation process. Compared with the LNCM materials produced by a traditional carbonate coprecipitation method, the prepared LNCM material synthesized through this modified method reveals a better hexagonal layered structure, smaller particle sizes (ca. 110.5 nm), and higher specific surface areas. Because of its unique structural characteristics, the as‐prepared LNCM material demonstrates excellent electrochemical properties including high rate capability and good cycleability when it is utilized as a cathode in the lithium ion battery (LIB).     

A simple and effective strategy to synthesize Al2O3-coated LiNi0.8Co0.2O2 cathode materials for lithium ion battery

A facile method has been developed to synthesize Al₂O₃-coated LiNi_0.8Co_0.2O₂ cathode materials. The sample was characterized by X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM) and energy dispersive analysis of X-rays (EDAX). Electrochemical tests show that the cycling stability of LiNi_0.8Co_0.2O₂ at room temperature is effectively improved by Al₂O₃ coating. The differential scanning calorimetry (DSC) and high temperature (60 °C) cycling tests indicate that Al₂O₃ coating can also improve the thermal stability of LiNi_0.8Co_0.2O₂, which is attributed to that the coating layer can protect the LiNi_0.8Co_0.2O₂ particles from reacting with the electrolyte.     

Synthesis and Electrochemical Characterization of Gradient Composite LiNi1-yCoyO2 Used as Cathode Materials in Lithium-ion Battery

Gradient composites, LiNi1-yCoyO2, are synthesized from coated spherical Ni(OH)2 precursor. These composites could be applied as new cathode materials in lithium-ion batteries because they have low cobalt content (y≤0.2)and exhibit excellent properties during high-rate charge/discharge cycles. The initial discharge capacity of coated composite of LiNio.95Co0.05O2 is 186 mAh/g, and the decreasing rate of the capacity is 3.2% in 50 cycles at 1C rate. It has been verified by TEM and EDX experiments that a core-shell structure of the composite particles develops because of the cobalt enrichment near the surfaces, and the formation of the cobalt enrichment layer is sensitive to sintering temperature. High cobalt surface concentration may reduce the undesired reactions and stabilize the structure of the particles.     

锰离子氧化沉淀法实现锂离子电池LiNi0.8Co0.05Mn0.15O2材料的回收和利用

以浓盐酸为浸出剂,以NaOH和NH₄HCO₃为沉淀剂,利用Mn²⁺在碱性条件下的氧化反应改变离子的沉淀次序进而分步回收的方案,探究了浓盐酸酸浸处理三元正极材料LiNi_0.8Co_0.05Mn_0.15O₂的最佳条件。在分步沉淀过程中,Mn²⁺被氧化为不溶于非还原性酸的MnO(OH)₂,并在酸性条件下回收。Ni、Co则在碱性条件下利用NaOH回收,而Li则利用NH₄HCO₃回收。该方法中Mn的回收率达到85.1%,产品纯度达到98.6%; Li的回收率达到95.0%,产品纯度达到99.3%。由回收材料重新合成的三元正极组装的软包电池的首圈放电比容量达到了175 mAh·g^-1,可以以超过99.5%的库仑效率稳定循环50圈。     

Synergistic Dual-Additive Electrolyte Enables Practical Lithium-Metal Batteries

A rechargeable Li metal anode coupled with a high-voltage cathode is a promising approach to high-energy-density batteries exceeding 300 Wh kg⁻¹. Reported here is an advanced dual-additive electrolyte containing a unique solvation structure and it comprises a tris(pentafluorophenyl)borane additive and LiNO₃ in a carbonate-based electrolyte. This system generates a robust outer Li₂O solid electrolyte interface and F- and B-containing conformal cathode electrolyte interphase. The resulting stable ion transport kinetics enables excellent cycling of Li/LiNi_0.8Mn_0.1Co_0.1O₂ for 140 cycles with 80 % capacity retention under highly challenging conditions (≈295.1 Wh kg⁻¹ at cell-level). The electrolyte also exhibits high cycling stability for a 4.6 V LiCoO₂ (160 cycles with 89.8 % capacity retention) cathode and 4.95 V LiNi_0.5Mn_1.5O₄ cathode.