Quantification of Conversion Degree and Monomer Elution from Dental Composite Using HPLC and Micro-Raman Spectroscopy

The purpose of the study was to analyze the correlation between the quantity of eluted monomers from dental resin-based composite using reverse-phase HPLC and the degree of conversion (DC) using micro-Raman spectroscopy, and to evaluate the influence of the energy of polymerization delivered on the composite material and the applied resin layer thickness on these properties. There was direct proportion in degree of conversion and inverse proportion in monomer elution when the energy of light polymerization was increased from 20 to 40 J cm^?2; however, further increase in energy density did not influence significantly the DC and the elution of monomers. Investigating the depth of cure significant differences could be measured both in DC and the elution of monomers. 1 mm layer increment up to 3 mm from the top led to 10 % decrease in DC and 30–35 % increase in monomer elution. Further increase in depth from 3 to 4 mm caused 30 % drop in DC and 55 % increase in the amount of leached monomers. The overall result of the findings indicates that direct correlation exists between DC of composite and the elution of unreacted monomers.     

Determination of degree of conversion as a function of depth of a photo-initiated dental restoration composite—III application to commercial Prodigy Condensable™

In this third work, we evaluated the degree of conversion (DC) versus depth of dental filling composite named Prodigy Condensable™ using infrared spectroscopy. Confirming previous results, there was a gradual reduction of DC with increasing depth but the composite exhibited extreme values of DC, an upper value (45.9%) on the surface and a lower one (6.1%) at a depth of 5 mm. The composite presented the worst performance among materials studied. The composite formulation was 80% of inorganic fillers and BisfenolA/dimethacrylate (BisGMA) (18%)/triethyleneglycoldimethacrylate (TEGDMA) (2.0%) as monomers. As stated before, type/ratio/viscosity of monomers and type, amount, size and size distribution of fillers all together had an important role in the cure reaction contributing to the final performance of the composite.     

Kinetic and particle size studies of emulsion polymerization of methyl methacrylate and styrene with using polyamidoamine dendrimer as seed

The emulsion polymerization of methyl methacrylate (MMA) and styrene (St) were investigated with using polyamidoamine (PAMAM) dendrimer as seed, potassium persulfate as initiator and sodium dodecyl sulfate as emulsifier. The effects of 4.0GPAMAM dendrimer concentration, initiator concentration, emulsifier concentration, monomer concentration, and polymerization temperature on the monomer conversion and polymerization rate were investigated. At the same time, the influence of the generation of PAMAM dendrimer on latex particle size was studied also. The results showed that the monomer conversion and polymerization rate increased with increasing initiator concentration, emulsifier concentration, monomer concentration, and polymerization temperature. But polymerization rate increased firstly with an increase in the 4.0GPAMAM dendrimer from 0.03 g to 0.09 g and then decreased with further increase to 0.12 g. When the concentration of 4.0GPAMAM dendrimer less than 1.449 × 10^?4 mol/L, the kinetic equation can be expressed by Rp∝[4.0GPAMAM]^0.772[SDS]^0.562[KPS]^0.589[M]^0.697, and the activation energy (Ea) of emulsion polymerization is 62.56kJ/mol. In additional, the copolymer latex particle size decreased and possessed monodispersity with increasing the generation of PAMAM dendrimer. According to FT-IR spectrum analysis, PAMAM dendrimer is successfully incorporated into the poly(PAMAM-St–MMA) latex particles.     

Decreasing the Polymerization Potential Improves the Selectivity of PPD-Coated Disc Biosensors for Glutamate

Abstract

The selectivity of glutamate microdisc biosensors coated with poly(o-phenylenediamine) (PPD) as the interference-rejecting layer against ascorbic acid was observed to be very low. Enhancement in the selectivity was noticed when the electropolymerization potential for the polymerization of the o-phenylenediamine monomer was decreased from 0.65 V to 0.40 V vs. Ag/AgCl. The selectivity coefficient increased from ?34.93±3.75% (n = 5) to 53.05 ± 4.33% (n = 3). Decreasing the polymerization potential decreases the rate of formation of the polymer and improves the compactness of the polymer layer formed, thereby increasing the selectivity of the electrodes.     

乳液聚合法制备聚合物与十二醇复合乳胶粒

通过乳液聚合法, 以苯乙烯、丙烯酸丁酯为主要单体, 以甲基丙烯酸为功能性单体, 以二乙烯基苯或二甲基丙烯酸乙二醇酯为交联剂, 制备了包覆有十二醇的聚合物复合颗粒. 通过动态光散射粒径仪和透射电镜观测乳胶粒粒径和形态, 气相色谱法测试了十二醇的包覆率, 并探讨了聚合过程中十二醇包覆率的变化情况. 结果表明十二醇的包覆率和十二醇与单体的质量比及单体转化率显著相关, 并且在聚合过程中包覆率存在先升后降的趋势. 实验发现十二醇包覆率的先升后降是由聚合物和十二醇的相容性不好引起的.     

Living cationic polymerization of vinyl ethers with a urethane group

To study the possibility of living cationic polymerization of vinyl ethers with a urethane group, 4‐vinyloxybutyl n‐butylcarbamate ( 1 ) and 4‐vinyloxybutyl phenylcarbamate ( 2 ) were polymerized with the hydrogen chloride/zinc chloride initiating system in methylene chloride solvent at ?30 °C ([monomer]₀ = 0.30 M, [HCl]₀/[ZnCl₂]₀ = 5.0/2.0 mM). The polymerization of 1 was very slow and gave only low‐molecular‐weight polymers with a number‐average molecular weight (M_n) of about 2000 even at 100% monomer conversion. The structural analysis of the products showed occurrence of chain‐transfer reactions because of the urethane group of monomer 1 . In contrast, the polymerization of vinyl ether 2 proceeded much faster than 1 and led to high‐molecular‐weight polymers with narrow molecular weight distributions (MWDs ≤ ～1.2) in quantitative yield. The M_n's of the product polymers increased in direct proportion to monomer conversion and continued to increase linearly after sequential addition of a fresh monomer feed to the almost completely polymerized reaction mixture, whereas the MWDs of the polymers remained narrow. These results indicated the formation of living polymer from vinyl ether 2 . The difference of living nature between monomers 1 and 2 was attributable to the difference of the electron‐withdrawing power of the carbamate substituents, namely, n‐butyl for 1 versus phenyl for 2 , of the monomers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2960–2972, 2004     

Cell Debris Self-Immobilized Thermophilic Lipase: a Biocatalyst for Synthesizing Aliphatic Polyesters

The paper explored the catalytic activity of a cell debris self-immobilized thermophilic lipase for polyester synthesis, using the ring-opening polymerization of ε-caprolactone as model. Effects of biocatalyst concentration, temperature, and reaction medium on monomer conversion and product molecular weight were systematically evaluated. The biocatalyst displayed high catalytic activity at high temperatures (70–90 °C), with 100 % monomer conversion. High monomer conversion values (>90 %) were achieved in both hydrophobic and hydrophilic solvents, and also in solvent-free system, with the exception of dichloromethane. Poly(ε-caprolactone) was obtained in 100 % monomer conversion, with a number-average molecular weight of 1,680 g/mol and a polydispersity index of 1.35 in cyclohexane at 70 °C for 72 h. Furthermore, the biocatalyst exhibited excellent operational stability, with monomer conversion values exceeding 90 % over the course of 15 batch reactions.     

LC–UV Methodology for Simultaneous Determination of Lamivudine and Zidovudine in Plasma by Liquid–Liquid Extraction

This study describes an accurate, sensitive, and specific chromatographic method for the simultaneous quantitative determination of lamivudine and zidovudine in human blood plasma, using stavudine as an internal standard. The chromatographic separation was performed using a C8 column (150 × 4.6 mm, 5 μm), and ultraviolet absorbency detection at 270 nm with gradient elution. Two mobile phases were used. Phase A contained 10 mM potassium phosphate and 3% acetonitrile, whereas Phase B contained methanol. A linear gradient was used with a variability of A-B phase proportion from 98–2% to 72–28%, respectively. The drug extraction was performed with two 4 mL aliquots of ethyl acetate.

     

Thermal and spectral behaviour of a light-cured methacrylate-based composite material used in dentistry

The evolution of the polymerization of a light-cured methacrylate-based composite material (Pekalite) used in dentistry was studied. Fourier transform infrared spectroscopy and thermal analysis (TA) showed that with increasing the photo-polymerization time from 5 to 60 s, the degree of conversion increases from 32.5 to 59.6 % and thermal stability of the composite material increases from 144.6 to 270 °C. Growth of photo-polymerization time from 5 to 60 s produces an improvement in the mechanical strength of the composite material from 153 to 248 MPa. Spectral analysis and TA are two complementary and rapid methods for determining the degree of polymerization of composite materials used in dentistry.     

三羟甲基丙烷三丙烯酸酯-苯乙烯沉淀聚合高产率制备高交联单分散聚合物微球

以三羟甲基丙烷三丙烯酸酯(TMPTA)-苯乙烯(St)为单体,偶氮二异丁腈(AIBN)为自由基引发剂,通过在乙醇中的沉淀聚合可制得高交联单分散P(TMPTA-St)聚合物微球.对单体转化率,微球以及可溶性低聚物的产率进行了测试.结果表明,使用10 wt%至60 wt%的交联剂TMPTA进行聚合可获得单分散微球,产率在50%左右.增加TMPTA用量可提高微球产率和单体转化率.增加引发剂AIBN用量对提高微球产率也有促进作用,但同时可溶性低聚物产率也增加.向乙醇中加入水作为反应介质结合适当增加AIBN用量可使单体转化率达到98%,微球产率高于90%.对实验结果进行了解释,对聚合机理进行了讨论.     

Efficiencies of Various in situ Polymerizations of Liquid Electrolytes and the Practical Implications for Quasi Solid-state Batteries

In situ polymerization of liquid electrolytes is currently the most feasible way for constructing solid-state batteries, which, however, is affected by various interfering factors of reactions and so the electrochemical performance of cells. To disclose the effects from polymerization conditions, two types of generally used in situ polymerizing reactions of ring-opening polymerization (ROP) and double bond radical polymerization (DBRP) were investigated on the aspects of monomer conversion and electrochemical properties (Li⁺-conductivity and interfacial stability). The ROP generated poly-ester and poly-carbonate show a high monomer conversion of ≈90 %, but suffer a poor Li⁺-conductivity of lower than 2×10⁻⁵ S cm⁻¹ at room temperature (RT). Additionally, the terminal alkoxy anion derived from the ROP is not resistant to high-voltage cathodes. While, the DBRP produced poly-VEC(vinyl ethylene carbonate) and poly-VC(vinylene carbonate) show lower monomer conversions of 50–80 %, delivering relatively higher Li⁺-conductivities of 2×10⁻⁴ S cm⁻¹ at RT. Compared two polymerizing reactions and four monomers, the VEC-based F-containing copolymer possesses advantages in Li⁺-conductivity and antioxidant capacity, which also shows simultaneous stability towards Li-metal with the help of LiF-based passivating layer, allowing a long-term stable cycling of high-voltage quasi solid-state cells.     

Vinyl polymerization. 413. Polymerization of vinyl monomer initiated by poly(vinylbenzyltrimethyl)-ammonium chloride

The polymerization of vinyl monomer initiated by an aqueous solution of poly(vinylbenzyltrimethyl)ammonium chloride (Q-PVBACI) was carried out at 85°C. Styrene, p-chlorostyrene, methyl methacrylate, and i-butyl methacrylate were polymerized, whereas acrylonitrile and vinyl acetate were not. The effects of the amounts of vinyl monomer, Q-PVBACI, and water on the conversion of vinyl monomer were studied. The overall activation energy in the polymerization of styrene was estimated as 79.1 kJ mol^?1. The polymerization proceeded through a radical mechanism. The selectivity of vinyl monomer was discussed by “a concept of hard and soft hydrophobic areas and monomers.”     

Graft Copolymerization of 2‐Acrylamido‐2‐methyl Propane Sulfonic Acid on Dimethyl Sulfoxide Pretreated Poly(Ethylene Terephthalate) Films Using Cerium Ammonium Nitrate as Initiator

Abstract

In this study, graft polymerization of 2‐acrylamido‐2‐methyl propane sulfonic acid (AMPS) on poly(ethylene terephthalate) (PET) films using cerium ammonium nitrate (CeAN) as an initiator was investigated. Before the polymerization reaction was carried out, films were swelled in dimethyl sulfoxide (DMSO) at 140°C for 1 h. The effect of polymerization temperature, time, initiator, and monomer concentrations on the graft yield were investigated. It was observed that the graft yield was initially increased with increasing temperature, monomer, and initiator concentrations; and then decreased. Graft yield was found to increase with increasing polymerization time up to 5 h, then remain constant. The effects of monomer and initiator inclusions on the grafting yield were also examined. Optimum conditions for grafting were found to be [AMPS] = 1.0 M, [Ce⁴⁺] = 1.5 × 10^?2 M, T = 85°C and t = 5 h. The rate of grafting was found to be proportional to the 0.1 and 0.4 powers of monomer and initiator concentrations, respectively. The overall activation energy for the grafting was calculated to be 11.4 kcal mol^?1. The effect of grafting on PET film properties such as intrinsic viscosity and water absorption capacity were determined. The grafted PET films were characterized with FTIR spectroscopy and scanning electron microscopy (SEM).     

Synthesis of nanocylinders consisting of graft block copolymers by the photo‐induced ATRP technique

Photoinduced atom transfer radical polymerizations (ATRP) of t‐butyl methacrylate (BMA) were carried out, initiated by model initiator benzyl N,N‐diethyldithiocarbamate (BDC) in the presence of CuCl/bipyridine (bpy) under UV irradiation. We performed the first‐order time‐conversion plots in this polymerization system, and the straight line in the semilogarithmic coordinates indicated a first‐order in the monomer. The molecular weight of poly(t‐butyl methacrylate) (PBMA) increased in direct proportion to monomer conversion. The molecular weight distribution (M_w/M_n) of PBMA was about 1.3. The initiator efficiency, f, was close to 1.0, which indicated that no side reactions occurred. A copper complex, CuCl/bpy, reversibly activated the dormant polymer chains via a N,N‐diethyldithiocarbamate (DC) transfer reaction such as Cu(DC)Cl/bpy, and it was dynamic equilibrium that was responsible for the controlled behavior of the polymerization of BMA. On the basis of this information, we established a preparation method of nanocylinders consisting of graft block copolymers by grafting from photoinduced ATRP of multifunctional polystyrene having DC pendant groups with vinyl monomers [first monomer, BMA; second monomer, styrene or methyl methcrylate (MMA)]. We have carried out the characterization of such nanocylinders in detail. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 63–70, 2005     

Polymer modification of colloidal particles by spontaneous polymerization of surface active monomers

Adsorption and spontaneous polymerization of head- or tail-type surface active monomers having long methylene chains on colloidal silica and δ-alumina were investigated. Both head-type and tail-type ammonium monomers on silica in chloroform or tetrahydrofuran had the maximum adsorption on the respective adsorption isotherm. Above the monomer concentration giving the maximum adsorption, it was observed that the monomer formed micelles or clusters in bulk solution with removal of adsorbed water molecules from the silica surface. At the monomer concentration giving the maximum adsorption, heating the silica suspension containing the monomer at 40°C or 60°C in tetrahydrofuran or chloroform solution resulted in spontaneous polymerization. The composite particles formed by polymerization were observed to have many spots consisting of polymer on the surface. Therefore, it is suggested that the monomers are concentrated by micelle-like aggregation on the silica surface and consecutively spontaneous polymerization takes place. Adsorption of an anion-type monomer having a carboxyl group on δ-alumina, which exhibited a positive ζ potential in neutral aqueous solution, was higher than that on colloidal silica, but did not spontaneously polymerize on alumina. Received: 13 June 1998 Accepted in revised form: 19 August 1998     

Photoinitiated polymerization of methacrylic monomers in a polybutadiene matrix (PB): Kinetic,mechanistic, and structural aspects

The kinetics and mechanism of the photoinitiated polymerization of tetrafunctional and difunctional methacrylic monomers [1,6‐hexanediol dimethacylate (HDDMA) and 2‐ethylhexyl methacrylate (EHMA)] in a polybutadiene matrix (PB) have been studied. The maximum double‐bond conversion, the maximum polymerization rate, the intrinsic reactivity, and the kinetic constants for propagation and termination have been calculated. Unlike the behavior followed by the SBS‐HDDMA and PS‐HDDMA systems, where a reaction‐diffusion mechanism occurs from the start of the polymerization at low monomer concentrations (<30–40%), in the PB‐HDDMA system the reaction diffusion controls the termination process only after approximately 10% conversion is reached, as for the bulk polymerization of polyfunctional methacrylic monomers. Before reaching 10% conversion the behavior observed can be better explained by a combination of segmental diffusion‐controlled (autoaccelerated) and reaction‐diffusion mechanisms. This is probably a consequence of the lower force of attraction between the monomer and the matrix and between the growing macroradical and the matrix than those corresponding to the other systems mentioned. For the PB‐EHMA system, the termination mechanism is principally diffusion‐controlled from the beginning of the polymerization for monomer concentrations below 30–40%, and for higher monomer concentrations, a standard termination mechanism takes place (k_t ≈ 10⁶) at low double‐bond conversions, which is diffusion‐controlled for high conversions (>40%). For PB‐HDDMA and PB‐EHMA systems, crosslinked polymerized products are obtained as a result of the participation of the double bonds of the matrix in the polymerization process. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2444–2453, 2001     

Use of germanium initiators in ring‐opening polymerization of L‐lactide

Three different, new germanium initiators were used for ring‐opening polymerization of L ‐lactide. Chlorobenzene and 120 °C was a usable polymerization system for solution polymerization, and the results from the polymerizations depended on the initiator structure and bulkiness around the insertion site. The average molecular weights as measured by size exclusion chromatography increased linearly with the monomer conversion, and the molecular weight dispersity was around 1.2 for initiators 1 and 2 , whereas it was around 1.4 for initiator 3 . The average molecular weight of poly(L ‐lactide) could be controlled with all three initiators by adding different ratios of monomer and initiator. The reaction rate for the solution polymerization was, however, overall extremely slow. With an initial monomer concentration of 1 M and a monomer‐to‐initiator ratio of 50, the conversion was 93% after 161 h for the fastest initiator. In bulk polymerization, 160 °C, the conversion was 90% after 10 h. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3074–3082, 2003     

Cationic Photocrosslinkable Polydimethylsiloxane. III. Synthesis and Photocrosslinking of Polydimethylsiloxane Bearing Oxetane Groups

Abstract

From 3-hydroxymethyl-3-methyl oxetane, we synthesized three oxetane monomers with allylic, diethoxysilane or triethoxysilane functions. These monomers allowed us to prepare different polydimethylsiloxanes bearing oxetane groups by two routes. One is hydrosilylation of allylic monomer on hydrogeno polydimethylsiloxane, with different percentages of Si-H bonds. The second route is a condensation of α,ω-dihydroxy polydimethylsiloxane with di and tri ethoxysilane monomers. By using a photocalorimeter, we studied the kinetic of cationic photopolymerization of a polydimethylsiloxane bearing 7.4% oxetane functions. Influence of temperature in the range 35 to 125°C showed a maximum conversion for 80°C due to an increase in transfer and termination reactions.     

Synthesis and photopolymerizations of new phosphonated monomers for dental applications

Three novel phosphonated methacrylate monomers have been synthesized and studied for use in dental applications. Two of the monomers were synthesized from the reactions of glycidyl methacrylate (GMA) with (diethoxy‐phosphoryl)‐acetic acid (monomer 1 ) and (2‐hydroxy‐ethyl)‐phosphonic acid dimethyl ester (monomer 2 ). These monomers showed high crosslinking tendencies during thermal bulk and solution polymerizations. The third monomer (monomer 3 ) was prepared by the reaction of bisphenol A diglycidylether (DER) with (diethoxy‐phosphoryl)‐acetic acid and subsequent conversion of the resulting diol to the methacrylate with methacryloyl chloride. The homopolymerization and copolymerization behaviors of the synthesized monomers were also investigated with glycerol dimethacrylate (GDMA), triethylene glycol dimethacrylate (TEGDMA), and 2,2‐bis[4‐(2‐hydroxy‐3‐methacryloyloxy propyloxy) phenyl] propane (bis‐GMA) using photodifferential scanning calorimetry at 40 °C using 2,2′‐dimethoxy‐2‐phenyl acetophenone (DMPA) as photoinitiator. Monomer 1 showed polymerization rate similar or greater than dimethacrylates studied here but with higher conversion. The maximum rate of polymerizations decreased in the following order: 1 ～TEGDMA>GDMA～bis‐GMA～ 3 > 2 . A synergistic effect in the rate of polymerization was observed during copolymerizations. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2290–2299, 2008     

Systematic Investigation of the Photopolymerization of Imidazolium-Based Ionic Liquid Styrene and Vinyl Monomers

The use of ionic liquids (ILs) as media in radical polymerizations has demonstrated the ability of these unique solvents to improve both reaction kinetics and polymer product properties. However, the bulk of these studies have examined the polymerization behavior of common organic monomers (e.g., methyl methacrylate, styrene) dissolved in conventional ILs. There is increasing interest in polymerized ILs (poly(ILs)), which are ionomers produced from the direct polymerization of styrene-, vinyl-, and acrylate-functionalized ILs. Here, the photopolymerization kinetics of IL monomers are investigated for systems in which styrene or vinyl functionalities are pendant from the imidazolium cation. Styrene-functionalized IL monomers typically polymerized rapidly (full conversion ≤1 min) in both neat compositions or when diluted with a nonpolymerizable IL, [C₂mim][Tf₂N]. However, monomer conversion in vinyl-functionalized IL monomers is much more dependent on the nature of the nonpolymerizable group. ATR-FTIR analysis and molecular simulations of these monomers and monomer mixtures identified the presence of multiple intermolecular interactions (e.g., π–π stacking, IL aggregation) that contribute to the polymerization behaviors of these systems. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 2364–2375