HRGC/FID/NPD and HRGGC/MSD study of Colombian ylang-ylang (Cananga odorata) oils obtained by different extraction techniques

Steam distillation (SD), simultaneous distillation-solvent extraction (SDE), and supercritical (CO₂) extraction (SFE) were used to isolate volatile secondary metabolites from fresh, totally mature flowers of Colombian ylang-ylang (Cananga odorata). The various extracts were analyzed by capillary chromatography (DB-1, DBWAX, 60 m columns) using FID, NPD or MSD (EI, 70 eV). Kováts indexes, mass spectra, or standard substances were employed for compound identification. 51, 70, and 73 compounds at concentrations above 100 ppb were detected in the SD, SDE, and SFE extracts, respectively. The main constituents of these extracts were linalool (20.7, 28.0, and 16.5%), germacrene-D (10.1, 3.1, and 20.3%) benzyl benzoate (14.1, 2.9, and 3.9%), benzyl acetate (9.6, 17.0, and 6.2%), caryophyllene (3.1, 2.9, and 3.9%), and p-methylanisole (6.8, 6.1, and 2.7%). 85% of the composition of SDE extracts was represented by oxygenated compounds. Heavy hydrocarbons (C_n >20) and fatty acids were found only in the SFE extracts, which also had a higher content of nitrogenated compounds (phenylacetonitrile, 4-methylbenzaldoxime, indole, 2-phenyl-nitroethane, and methyl anthranilate) and sesquiterpenes (43% vs 19.5% in SD and 8.1% in SDE) and 1.5 – 2 times lower concentration of monoterpenes and light oxygenated compounds than the SD (49.7%) and SDE (64.5%) extracts.     

Comparative analysis of the composition of essential oils and supercritical carbon dioxide extracts from the berries and needles of Estonian juniper (Juniperus communis L.)

The composition of the volatile oil of the common juniper (Juniperus communis L.) from Estonia was analyzed by gas chromatography (GC-FID) and gas chromatography-mass spectrometry (GC-MS). The yield and composition of the oil obtained by different methods (micro-distillation and extraction, SDE, and supercritical carbon dioxide extraction, SFE) from various parts of juniper (berries, needles) were compared. The oil yield ranged from 0.7 to 2.1%. The content of α-pinene of juniper-berry essential oil was 47.9, that of juniper needleoil, 36.4%. The oil yields and composition obtained by SDE and SFE from juniper needles were similar. The oil obtained by SFE from juniper berries contained more sesquiterpenes and high boiling compounds than that obtained by SDE.     

HRGC/FID and HRGC/MSD Analysis of the Secondary Metabolites Obtained by Different Extraction Methods from Lepechinia schiedeana,and in Vitro Evaluation of Its Antioxidant Activity

Steam distillation (SD), simultaneous distillation-solvent extraction (SDE), microwave-assisted solvent extraction (MWE), and supercritical (CO₂) extraction (SFE) were used to isolate secondary metabolites from Lepechinia schiedeana. The various extracts were analyzed by capillary gas-chromatography, on poly (dimethylsiloxane) (DB-1) and poly(ethyleneglycol) (INNOWAX), 60 m columns, using FID or MSD (EI, 70 eV). Kováts indexes, mass spectra, or standard compounds were employed for compound identification. 43, 61, 67, and 79 compounds at concentrations above 0.01% were detected in the SD, SDE, MWE, and SFE extracts, respectively. Ledol, C₁₅H₂₆O, was the major constituent (20.04–36.87%) in all extracts. Oxygenated sesquiterpenes (24.36–43.14%), C₁₀H₁₆, monoterpenes (27.70–39.87%), and C₁₅H₂₄, sesquiterpenes (10.04–22.22%) were the main groups of compounds present in SD, SDE, MWE, and SFE extracts. Heavy hydrocarbons (C_n > 15), diterpenoids, and phytosterols were found only in MWE and SFE extracts. The antioxidant activity of Lepechinia schiedeana was measured by the HRGC quantification of the volatile carbonyl compounds, final products of lipoxidation, released in a model lipid system (sunflower oil) by the effect of the Fenton reagent. The concentration of volatile carbonyl compounds decreased by 65% when lipid oxidation was induced in the presence of macerated Lepechinia plant. The protection of polyunsaturated acids in sunflower oil was also studied by measuring their concentrations after heating of the oil (180°C, 2 h) with and without macerated Lepechinia plant.     

Development of a sequential supercritical fluid extraction method for the analysis of nitrated and oxygenated derivatives of polycyclic aromatic hydrocarbons in urban aerosols

A two-step supercritical fluid extraction (SFE) method has been developed for the analysis of oxygenated and nitrated polycyclic aromatic hydrocarbons (oxy- and nitro-PAHs, respectively) present in urban aerosol samples. The proposed SFE procedure first involves an extraction step using pure CO2 in order to remove the less polar compounds from the matrix and a second consecutive step using toluene-modified CO2. The oxy- and nitro-PAHs are obtained in the second step. Parameters affecting both collection efficiencies and the selective extraction of oxy- and nitro-PAHs in the second SFE step were optimised. Analysis of the extracts was performed using gas chromatography with electron-capture detection and coupled to mass spectrometry. The proposed SFE method was compared with a conventional extraction technique such as sonication and good agreement in the results was obtained. Nevertheless, clean up of sonication extracts was needed, whereas no purification was necessary for SFE extracts. The SFE method was applied to the analysis of oxy- and nitro-PAHs in urban aerosol samples and 9-fluorenone, 9,10-anthraquinone, 2-methyl-9,10-anthraquinone, benzanthrone, benz[a]anthracene-7,12-dione and 1-nitropyrene were identified at concentrations ranging between 15 and 364 pg m(-3).     

Characterization of volatile components of tea flowers (Camellia sinensis) growing in Kangra by GC/MS

Volatile flavour components of tea flowers (Camellia sinensis) were isolated by two methods viz. simultaneous distillation extraction (SDE), supercritical fluid extraction (SFE), analyzed by GC and GC/MS and compared with headspace analysis (HS). The composition of the volatile components extracted by the three methods differed considerably. In SFE, phenylethanol (14.7%), linalool (7.9%), (E)-linalool oxide furanoid (3.5%), epoxy linalool (1.6%), geraniol (2.3%) and hotrienol (1.5%) were major components. m-Xylene (2.6%), (E)-linalool oxide pyranoid (5.4%), p-myrcene (5.2%), alpha-cadinol (4.3%) and methyl palmitate (2.9%) were major compounds isolated by SDE. 3-hexenol (2.1%) (E)-4,8-dimethyl-1,3,7-nonatriene (20.9%) and linalool (35.1%) are major components in headspace analysis. Acetophenone and pheromone germacrene D is detected in tea flowers by all the methods studied. Floral, fresh and fruity odour of tea flowers is retained by SFE as there is very little loss of heat sensitive volatiles in SFE. The flavour isolated from SFE has superior quality compared to SDE.     

Comparison of supercritical fluid and Soxhlet extractions for the isolation of nitro compounds from soils

Supercritical fluid extraction (SFE) with CO(2), a clean and rapid alternative to conventional Soxhlet extraction, was investigated for the extraction of nitro compounds from soil samples. Quantitative extraction by SFE was accomplished at a pressure of 25 MPa and an extraction temperature of 60 degrees C, for 30 min in dynamic mode and using acetonitrile as modifier, and the results were comparable with those obtained by acetonitrile Soxhlet extraction (3 h) for all soil samples. Extracts from these two procedures were analyzed by gas chromatography coupled with mass spectrometry. Quantitative reproducibility for SFE extracts was acceptable (RSD 2-10%), and the quantity of solvent was reduced from 160 mL for Soxhlet extraction to 5 mL in the case of SFE.     

Supercritical fluid extraction of phenol compounds from olive leaves

A clean, highly selective supercritical fluid extraction (SFE) method for the isolation of phenols from olive leaf samples was examined. Total phenol extracts were determined using the Folin-Ciocalteu reagent. Dried, ground, sieved olive leaf samples (30 mg) are subjected to SFE, using carbon dioxide modified with 10% methanol at 334 bar, 100 degrees C (CO(2) density 0.70 g ml(-1)) at a liquid flow-rate of 2 ml min(-1) for 140 min. Diatomaceous earth is used to reduce the void volume of the extraction vessel. The influence of extraction variables such as modifier content, pressure, temperature, flow-rate, extraction time, and collection/elution variables, were studied. Supercritical fluid extracts were screened for acid compounds such as carboxylic acids and phenols using Electrospray-MS (in the negative ionization mode). SFE was found to produce higher phenol recoveries than sonication in liquid solvents such as n-hexane, diethyl ether and ethyl acetate. However, the extraction yield obtained was only 45%, using liquid methanol.     

Modeling of supercritical fluid extraction of flavonoids from Calycopteris floribunda leaves

The aim of this study was to obtain flavonoids extracts from Calycopteris floribunda leaves using supercritical fluid extraction (SFE) with CO₂ and a co-solvent. Pachypodol, a potential anticancer drug lead compound separated from the extracts, was examined. Classical organic solvent extraction (CE) with ethanol was performed to evaluate the high pressure method. HPLC analysis was introduced to interpret the differences between SFE and CE extracts in terms of antioxidant activity and the concentration of pachypodol. SFE kinetics and mathematical modeling of the overall extraction curves (OEC) were investigated. Evaluation of the models against experimental data showed that the Sovová model performs the best. The supercritical fluid extraction process was optimized using a central composite design (CCD), where temperature and pressure were adjusted. The optimal conditions of SFE were: pressure of 30 MPa and temperature of 35°C.     

Analysis of volatile secondary metabolites from Colombian Xylopia aromatica (Lamarck) by different extraction and headspace methods and gas chromatography

Hydrodistillation (HD), simultaneous distillation-solvent extraction (SDE), microwave-assisted hydrodistillation (MWHD), and supercritical fluid (CO2) extraction (SFE), were employed to isolate volatile secondary metabolites from Colombian Xylopia aromatica (Lamarck) fruits. Static headspace (S-HS), simultaneous purge and trap (P&T) in solvent (CH2Cl2), and headspace (HS) solid-phase microextraction (SPME) were utilised to obtain volatile fractions from fruits of X. aromatica trees, which grow wild in Central and South America, and are abundant in Colombia. Kováts indices, mass spectra or standard compounds, were used to identify more than 50 individual components in the various volatile fractions. beta-Phellandrene was the main component found in the HD and MWHD essential oils, SDE and SFE extracts (61, 65, 57, and ca. 40%, respectively), followed by beta-myrcene (9.1, 9.3, 8.2 and 5.1%), and alpha-pinene (8.1, 7.3, 8.1 and 5.9%). The main components present in the volatile fractions of the X. aromatica fruits, isolated by S-HS, P&T and HS-SPME were beta-phellandrene (53.8, 35.7 and 39%), beta-myrcene (13.3, 12.3 and 10.1%), p-mentha-1(7),8-diene (7.1, 10.6 and 10.4%), alpha-phellandrene (2.2, 5.0 and 6.4%), and p-cymene (2.2,4.7 and 4.4%), respectively.     

The use of supercritical fluid extraction for the determination of 4-deoxynivalenol in grains: The effect of the sample clean-up and analytical methods on quantitative results

Summary Deoxynivalenol (DON) is one of the trichothecene mycotoxins produced byFusarium molds in grains. Polar cosolvents in supercritical carbon dioxide (SC-CO₂) are needed to extract and isolate the polar DON moiety. This unfortunately results in the extraction of many interfering compounds from the grains into the extracts obtained by supercritical fluid extraction (SFE). Analysis of DON by high performance liquid chromatography (HPLC) using ultraviolet detection (UV) does not provide a specific detection method, although specific detection of DON can be enhanced by using purification steps after SFE. Alternatively, combining SFE with an immunoaffinity method can improve detection specificity and sample cleanup. In this study, SFE was employed to determine DON in grains and cereal products. The effectiveness of the SFE method was compared with two different solvent extraction methods. The extracted DON was quantitatively determined by HPLC-UV using external standardization or competitive enzymelinked immunosorbent assay (ELISA). In some cases, extracts were purified prior to quantitative analysis of the DON by using solvent partitioning, and/or solid phase extraction, or immunoaffinity columns. Therefore, this paper describes the analysis of DON in cereals using different extraction, cleanup and analysis methods. Names are necessary to report factually on available data: however, the USDA neither guarantees nor warrants the standard of the product, and the use of the name by USDA implies no approval of the products to the exclusion of others that may also be suitable.     

Analysis of citrates and benzoates used in poly(vinyl chloride) by supercritical fluid extraction and gas chromatography

Supercritical fluid extraction (SFE) has been demonstrated to be a useful tool in the determination of additives in polymeric materials. This paper describes the determination of some citrates and benzoates in poly(vinyl chloride) blended with 33–34% of plasticizer using off-line SFE followed by gas chromatography. Experimental factors affecting SFE have been studied by gravimetric analysis, followed by analysis of the extracts using a gas chromatograph equipped with a flame ionization detector. The extraction process is governed by the solubility of the plasticizers in the supercritical fluid or by their diffusion through the polymer matrix, which depend on the pressure and temperature used. Maximum extraction (>99%) is obtained at pressures and temperatures higher than 40 MPa and 80 °C, respectively. Due to purge losses, the collection efficiency of plasticizers into a liquid solvent ranges from 85 to 90%. The applicability of the SFE method is demonstrated using real samples and comparing the results with those obtained by conventional Soxhlet extraction.     

Comparison of various extraction techniques for isolation and determination of isoflavonoids in plants

In the present paper, the following extraction techniques have been used for extracting isoflavonoids from the species Matricaria recutita, Rosmarinus officinalis, Foeniculum vulgare, and Agrimonia eupatoria L.: supercritical fluid extraction (SFE), pressurized fluid extraction, matrix solid phase dispersion, ultrasonic extraction in an ultrasonic bath (USE) and by means of an ultrasonic homogeniser (HOM), extraction by means of Soxhlet apparatus (SOX), and solid phase extraction. Experimental optimization of all techniques has been carried out using a soybean flour. Subsequent analyses of the extracts were carried out by liquid chromatography with UV detection. The maximum yields of daidzein and genistein were obtained by extraction with the SOX, USE, and HOM techniques. The maximum yields of apigenin and biochanin A from herb samples were obtained by SFE.     

Identification and quantification of the volatile constituents in Cnidium monnieri using supercritical fluid extraction followed by GC‐MS

The volatile components of Cnidium monnieri were obtained by supercritical fluid extraction (SFE) and analyzed by GC‐MS (identification and determination of metabolites). The compounds were identified according to their retention times and mass spectra. The effects of different parameters, such as extraction pressure, temperature, dynamic extraction time, flow rate of CO₂, on the SFE of C. monnieri extracts were investigated. A total of 14 compounds of SFE extracts were identified. Osthole (69.52%), bornyl acetate (10.03%), α‐pinene (4.71%), and imperatorin (2.42%) were the major compounds identified in C. monnieri SFE extracts. The quantitation of osthole and imperatorin were then accomplished. The linear calibration ranges were all 5–1000 μg/mL for osthole and imperatorin by GC‐MS analysis. The recovery of osthole and imperatorin were in the range 96.5–101.8%. The LODs for osthole and imperatorin were 1.0 and 0.6 μg/mL, respectively.     

Off-line SFE-CZE analysis of carbamates residues in tobacco samples

Summary Determination of carbamate residues in tobacco samples was carried out by solid-liquid extraction (SLE) and supercritical-fluid extraction (SFE) methods, both developed for this purpose. The clean-up step was carried out on SPE-Florisil cartridges and the extracts analysed by capillary zone electrophoresis (CZE) with UV detection.The results were compared and SFE using CO₂-acetone showed the best results in terms of recovery and generally higher extraction power. SFE in conjunction with CZE proved suitable for carbamate residue analysis in real tobacco samples.     

Extraction of essential oil from Pimpinella anisum using supercritical carbon dioxide and comparison with hydrodistillation

Supercritical fluid extraction (SFE) of essential oil from Pimpinella anisum, using carbon dioxide as a solvent is presented in this work. An orthogonal array design OA9 (3(4)) was applied to select the optimum extraction condition. The effects of pressure, temperature, dynamic extraction time and methanol volume on the extraction efficiency were investigated by the three-level orthogonal array design. Results show that pressure has a significant effect on the extraction efficiency. The extract obtained from P. anisum by using supercritical fluid extraction was compared with the essential oil obtained by hydrodistillation, considering both quantity and quality of the product. SFE products were found to be of markedly different composition, compared with the corresponding hydrodistilated oil. The total amount of extractable substances obtained in SFE (7.5%) is higher than that obtained by hydrodistillation (3.1%) and SFE is faster than hydrodistillation method.     

GC-MS of volatile components of Schisandra chinensis obtained by supercritical fluid and conventional extraction

In this paper, the volatile compounds of Schisandra chinensis obtained by different extraction techniques including supercritical fluid extraction (SFE), steam distillation (SD), Soxhlet extraction (SE) and ultrasound-assisted extraction (UAE) were investigated for the first time. The sample preparation procedure for GC-MS analysis of the volatile compounds was optimized and then 37, 45, 27 and 37 compounds were identified in the samples obtained by SFE, SD, SE and UAE methods, respectively. As the therapeutic effect of the traditional Chinese medicine is usually based on multifarious essential components or the combination of them instead of only one component, the volatile compounds were compared in groups with the extracts by SE, SD and UAE. This would be more reasonable to evaluate the effects of an alternative technique to extracting multifarious essential components. Among the identified components in the SFE extract, 32 compounds were the same as that by three conventional methods, accounting for 90.5% of the volatile compounds identified. However, as the volatile compounds were classed into groups, it was easy to see that the Schisandra chinensis oil extracted by SFE was made up largely of aromatics and sesquiterpenoids (52.1 and 27.6%, respectively), with less amounts of monoterpenoids and other compounds, distinguishing SFE from the conventional extractions.     

Supercritical fluid extraction for identification and determination of volatile metabolites from Angelica dahurica by GC-MS

The volatile components of Angelica dahurica were obtained by supercritical fluid extraction (SFE) method. These oils obtained were analyzed by GC-MS (identification and determination of metabolites). The compounds were identified according to their retention indices and mass spectra (electron impact (EI), 70 eV). The effects of different parameters, such as pressure, temperature, flow rate of CO(2), and the amount of modifier, on the SFE of A. dahurica oil were investigated. A total of 50 compounds of SFE extracts were identified. Phellopterin (PO), isoimperatorin (IO), imperatorin (IM), alloimperatorin (AM), byakangelicin, isooxypeucedanin, and pimpinellin were the major coumarin compounds identified in A. dahurica SFE extracts. The quantitations of PO, IO, IM, and AM were then accomplished. The calibration curves showed good linearity (R(2) >0.99) in the concentration ranges tested. The recoveries were higher than 85%, with RSDs less than 10%. The GC-MS method was successfully validated and applied to the quantitation of A. dahurica.     

Development of a method for the rapid determination of pentachlorophenol in leather using supercritical fluid extraction with in situ derivatization

Pentachlorophenol (PCP) was extracted from leather with supercritical carbon dioxide and in situ acetylated under static SFE conditions in the presence of triethylamine. During the dynamic extraction step, the derivatives were removed from the matrix and collected with either a pure liquid (light petroleum) or a liquid-solid (light petroleum-solid sorbent (C18, alumina, Florisil or Celite)) trap. To prevent restrictor plugging, a suitable restrictor was designed. The clean-up of the extracts was optimized in this study. Different internal standards were tested and it was shown that not all of them were usable. The SFE results were compared with those obtained by Soxhlet extraction with methanol. With SFE instead of conventional Soxhlet extraction, the overall time required for determination of PCP in leather can be reduced from about 2 days to approx. 3 hours.     

Comparison of different extraction methods for the analysis of volatile secondary metabolites of Lippia alba (Mill.) N.E. Brown, grown in Colombia, and evaluation of its in vitro antioxidant activity

Hydrodistillation (HD), simultaneous distillation solvent extraction (SDE), microwave-assisted hydrodistillation (MWHD), and supercritical fluid (CO2) extraction (SFE) were employed to isolate volatile secondary metabolites from fresh leaves and stems of Colombian Lippia alba (Mill.) N.E. Brown. Kovàts indices, mass spectra or standard compounds were used to identify around 40 components in the various volatile fractions. Carvone (40-57%) was the most abundant component, followed by limonene (24-37%), bicyclosesquiphellandrene (5-22%), piperitenone (1-2%), piperitone (ca. 1.0%), and beta-bourbonene (0.6-1.5%), in the HD, SDE, MWHD, and SFE volatile fractions. Static headspace (S-HS), simultaneous purge and trap in solvent (CH2Cl2) (P&T), and headspace solid-phase microextraction (HS-SPME) were used to sample volatiles from fresh L. alba stems and leaves. The main components isolated from the headspace of the fresh plant material were limonene (27-77%), carvone (14-30%), piperitone (0.3-0.5%), piperitenone (ca. 0.4%), and beta-bourbonene (0.5-6.5%). The in vitro antioxidant activity of L. alba essential oil, obtained by hydrodistillation was evaluated by determination of hexanal, the main carbonyl compound released by linoleic acid subjected to peroxidation (1 mm Fe2+, 37 degrees C, 12 h), and by quantification of this acid as its methyl ester. Under the same conditions, L. alba HD-essential oil and Vitamin E exhibited similar antioxidant effects.     

Supercritical fluid extraction and quantitative determination of organophosphorus pesticide residues in wheat and maize using gas chromatography with flame photometric and mass spectrometric detection

An automated method using supercritical CO2 and clean-up by solid-phase extraction (SPE) using graphitized carbon black, has been developed for the quantitative determination of organophosphorus pesticide (OPP) residues in wheat and maize. Recoveries were as good as, or better than, those obtained using liquid extraction (LE) and gel permeation chromatography (GPC) for 10 OPP's spiked at levels equivalent to 0.05 and 0.50 microg/g. Lower limits of detection were possible using supercritical fluid extraction (SFE). Incurred residues were found in wheat and maize samples, and good agreement was obtained using SFE+SPE and LE+GPC. The SFE+SPE method required less analyst time and organic solvent, and hazardous waste was reduced.