1.3 GHz 9单元Ichiro型模型铜腔的预调谐

 以常用的多单元超导腔预调谐方法为基础,搭建了一套完整的预调谐系统,并实现了超导腔预调谐测量的自动化。实验首先通过网络分析仪对超导腔进行测量,利用Labview进行数据采集,并协同控制步进电机。通过“拉小珠”的微扰法,测量沿小珠运动路径的场分布。编写了一套Java程序,通过矩阵运算,计算出9单元腔各个腔单元频率的校正量。根据计算结果对9单元腔的某个单元进行挤压或拉抻,经多次上述操作后,在较高精度范围内,可将9单元铜腔的每个腔单元调谐至预期的目标频率。     

中国散裂中子源二期648 MHz超导腔调谐器设计

中国散裂中子源二期升级采用超导腔技术方案,其中在165～300 MeV能量段采用648 MHz 6-cell超导腔模组,每个模组中集成3只6-cell超导腔。超导腔工作在脉冲模式,为了保证超导腔2 K下的频率满足运行要求,每只超导腔需要一套低温调谐器对其频率进行精确调节控制。针对648 MHz 6-cell超导腔的结构和运行特点进行了低温调谐器的设计,采用快慢组合机构补偿超导腔的频率偏移,对调谐器的基本性能和超导腔脉冲模式运行下的动态洛伦兹失谐进行了分析。     

TESLA式高阶模衰减器的改进与设计研究

为了消除超导加速腔中高阶模场对加速粒子的影响, 在DESY的高阶模耦合器结构的基础上本文提出了改进的耦合器. 用HFSS程序针对1.5cell腔设计优化了高阶模耦合器, 得到高阶模耦合器对几种主要模式的吸收. 研究结果表明, 采用新型结构后, 衰减器对主要有害模的衰减由－40dB提高到－15dB, 使原有高阶模衰减器的性能明显提高. 该高阶模衰减器也适用于国产2cell超导腔的使用.     

北京大学光阴极注入器3+1/2超导腔机械性能

 介绍了北京大学光阴极注入器的核心部件3+1/2超导腔的机械性能的设计，通过ANSYS和SUPERFISH程序优化加强筋的个数和位置，解决了超导腔在脉冲条件下由于洛仑兹力引起的超导腔失谐以及当超导腔进行低温调谐时场平滑度变化过大的问题，同时针对复杂超导腔结构进行了低温调谐结构的设计。     

1.3 GHz超导腔的掺氮实验

为了大幅度提高纯铌超导腔的品质因数,从而降低其使用功耗,选择对超导腔进行高温氮掺杂处理。立足国内外大型加速器的需求,中国科学院高能物理研究所首先开展了1.3 GHz 1-cell超导腔的研究,包括常规处理以及氮掺杂实验,并且对掺杂前后的结果进行了分析、对比。结果表明,通过掺氮,两只1.3 GHz 1-cell细晶粒纯铌超导腔的品质因数均获得了显著提升,同时在超导腔低温垂直测试中观察到了比较明显的反常的品质因数随加速梯度变化的曲线,即"anti-Q-slope"现象。     

超导腔数字自激垂直测试系统

基于数字自激算法设计并实现的超导腔垂直测试系统提高了超导腔的垂直测试效率,为先进光源技术研发与测试平台(PAPS)的超导腔批量化生产提供了重要保障;垂直测试系统的射频前端和时钟分配系统采用了二次上下变频方案,可以在一定范围内灵活设置测试系统自激环路的工作频率,增大了该测试系统的工作带宽。利用此系统完成了1.3 GHz 9-cell超导腔的通带频率测试,结果表明,该测试系统能有效避免不同模式之间的串扰,具备较强的频率分辨能力(<800 kHz),保证多单元超导腔性能验证的进行。     

具有同空间特性的双波长可调谐TEACO2激光器

研制成功一种新型双波长TEACO2激光器,激光器在一对横向放电电极之间设置两个空间部分重叠的光栅_平面腔,两光栅沿腔轴一前一后放置,且在空间上交叠,两个腔相互利用,能够输出含有两种波长成分的激光脉冲。输出的同一激光脉冲中两波长激光场在空间上部分重叠,重叠程度和两种波长激光场的能量比均可通过调整前面光栅的水平横向位置加以控制,通过调节两光栅的角度选择所需支线,波长调谐方便且调谐范围较宽。该激光器在分离硼同位素的实验中得到了初步成功的应用。     

CSNS-II超导椭球腔形变电场平坦度仿真分析

超导椭球腔是一种通过冲压零件和电子束焊接而成型的薄壁结构,在加工过程中存在不可避免的形变,如单元倾斜、偏轴,单元长度偏差,从而影响椭球腔的轴向电场平坦度,进而降低椭球腔的运行电场梯度。因此,在椭球腔加工成型后要进行预调谐处理。椭球腔预调谐是通过对椭球腔整形,包括倾斜和偏轴矫正,单元长度矫正,以达到提高轴向电场平坦度的目的。采用COMSOL多物理场耦合软件对CSNS-II（China Spallation Neutron Source Phase II）超导椭球腔可能存在的形变进行了仿真计算,研究了各单元形变量对电场平坦度的影响,分析了腔体调谐位移量对电场平坦度的影响,为椭球腔预调谐提供数据参考,也为预调谐机的设计研制提供指导。另外,确定了椭球腔机械形变的要求,确保椭球腔机械加工质量满足CSNS-II升级的实际工程需求。     

高性能法布里—珀罗腔的研究

可调谐法布里－珀罗腔可用于频分复用，波分复用以及光孤子通信系统之中，是一种重要的光学器件。本文从原理上分析了制造性能优良的法布里－珀罗腔所应考虑的各种因素，结合两种先进的制腔方法，即腔外匹配和腔内加光阑法，解决了制做过程中所遇到的技术问题，制成的腔具有较高的性能。     

超导腔垂直测试数字化自激励环路研制

介绍北京大学垂直测试系统的数字化自激励环路系统,重点分析了实际测试中避免多单元(cell)超导腔模式串扰的方法以及偏离四倍频采样对信号幅度和相位的影响。该系统运行稳定可靠,可有效区分1.3 GHz8π/9模,解决了多cell超导腔测试中模式串扰问题。分析了超导腔自激励环路在垂直测试中的应用,介绍了北京大学垂直测试系统的数字化自激励环路,采用上下变频方案的射频前端和包括有限脉冲响应滤波器的数字算法,系统简洁扩展性强。重点分析了实际测试中避免多cell超导腔模式串扰的方法以及偏离四倍频采样对信号幅度和相位的影响。在多种不同频率超导腔的垂直测试中该系统运行稳定可靠,可有效区8π/9模,解决了多cell超导腔测试中模式串扰问题。     

Status of the IHEP 1.3 GHz superconducting RF program

The 1.3 GHz superconducting radio-frequency (SRF) technology is one of the key technologies for the ILC and future XFEL and ERL projects in China. With the aim to develop 1.3 GHz SRF technology, IHEP has started a program to build an SRF Accelerating Unit. This unit contains a 9-cell 1.3 GHz superconducting cavity, a short cryomodule, a high power input coupler, a tuner and a low level RF system. This program also includes the SRF laboratory upgrade, which will permit the unit to be built and tested at IHEP. The unit will be used for the 1.3 GHz SRF system integration study, high power horizontal test and possible beam test in the future. In this paper, we report the recent R&D status of this program. The first large grain low-loss shape 9-cell superconducting RF cavity made by IHEP reached 20 MV/m in the first vertical test in July, 2010. The prototype tuner and low level RF (LLRF) system are under test. The high power input coupler and cryomodule are under fabrication. Several key SRF facilities for 9-cell cavity surface treatment and pre-tuning were successfully commissioned and are in operation.     

Tuning for the first 9-cell TESLA cavity of PKU

A method based on circuit model is used to tune the first home-made 9-cell TESLA type superconducting niobium cavity at Peking University.After tuning,a flat field profile with a final π-mode frequency within 3 kHz of target frequency is achieved.The field flatness is measured by a bead-pull method,and the relative electric field is calculated from the frequency shift perturbed by the bead stepping along the axis of the cavity.     

Multi-pass,multi-bunch beam breakup for 9-cellTesla cavities in the ERL

Generally, the Energy Recovery Linac (ERL) needs specially designed high current superconducting RF cavities. In this paper, the threshold current of beam breakup for compact ERL facilities with 9-cell Tesla type cavities are investigated. The results show that it is feasible to adopt the 9-cell Tesla cavity for compact ERL test facilities with just a few cavities and beam current around 10 mA.     

Power coupler kick of the TRIUMF ICM capture cavities

The TRIUMF Injector CryoModule (ICM) adapted two superconducting single cavities as the capture section for the low injecting energy of 100 keV electrons. Coupler kick induced beam deflection and projected emittance growth are one of the prime concerns of the beam stability, especially at low energies. In low energy applications, the electron velocity changes rapidly inside the cavity, which makes the numerical analysis much more complicated. The commonly used theoretical formulas of the direct integral or the Panofsky- Wenzel theorem is not suitable for the kick calculation of β <1 electrons. Despite that, the above mentioned kick calculation method doesn't consider injecting electron energy, the beam offset due to the coupler kick may not be negligible because of the low injection energy even if the kick is optimized. Thus the beam dynamics code TRACK is used here for the simulation of the power coupler kick perturbation. The coupler kick can be compensated for by a judicious choice of the coupler position in successive cavities from upstream to downstream. The simulation shows that because of the adiabatic damping by the following superconducting 9-cell cavity, even for the worst orbit distortion case after two capture cavities, the kick is still acceptable at the exit of the ICM after reaching 10 MeV. This paper presents the analysis of the transverse kick and the projected emittance growth induced by the coupler for β <1 electrons. The simulated results of the TRIUMF ICM capture cavities are described and presented.     

直线加速器超导段故障补偿的人工智能算法研究

强流直线加速器的长时间稳定运行是该领域的难点和前沿课题之一。以加速器驱动嬗变研究装置(CiADS)的加速器为例,利用TraceWin软件模拟的虚拟加速器数据,提出了基于人工智能算法的超导腔失效的分段故障补偿方法。当有腔体故障时,故障腔的相邻器件将用于重新匹配束流包络,而所有下游腔均可用于补偿束流能量。与传统的优化方法相比,该方法可实现低能耗的超导腔段的故障补偿,具有计算速度快、普适性强等优点,为实际应用器件故障补偿提供了新的可行性。