Flow through a helically coiled annulus

In this paper the flow is studied of an incompressible viscous fluid through a helically coiled annulus, the torsion of its centre line taken into account. It has been shown that the torsion affects the secondary flow and contributes to the azimuthal component of velocity around the centre line. The symmetry of the secondary flow streamlines in the absence of torsion, is destroyed in its presence. Some stream lines penetrate from the upper half to the lower half, and if is further increased, a complete circulation around the centre line is obtained at low values of for all Reynolds numbers for which the analysis of this paper is valid, being the ratio of the torsion of the centre line to its curvature.Nomenclature A =constant - a outer radius of the annulus - b unit binormal vector to C - C helical centre line of the pipe - D rL - g 1000 - K Dean number=Re² - L 1+r sin - M (L ²+ ² r ²)^1/2 - n unit normal vector to C - P, P pressure and nondimensional pressure - p ₀, p pressures of O(1) and O() - Re Reynolds number=aW ₀/ - (r, , s), (r, , s) coordinates and nondimensional coordinates - nonorthogonal unit vectors along the coordinate directions - r ₀ radius of the projection of C - t unit tangent vector to C - V _r, V , V _s velocity components along the nonorthogonal directions - V_r, V, V _s nondimensional velocity components along - W ₀ average velocity in a straight annulus Greek symbols , curvature and nondimensional curvature of C - U, V, W lowest order terms for small in the velocity components along the orthogonal directions t - _r, , _s first approximations to V _r , V, V _s for small - =/=/ - kinematic viscosity - density of the fluid - , torsion and nondimensional torsion of C - , stream function and nondimensional stream function - nondimensional streamfunction for U, V - a inner radius of the annulus After this paper was accepted for publication, a paper entitled On the low-Reynolds number flow in a helical pipe, by C.Y. Wang, has appeared in J. Fluid. Mech., Vol 108, 1981, pp. 185–194. The results in Wangs paper are particular cases of this paper for =0, and are also contained in [9].     

Transport in ordered and disordered porous media I: The cellular average and the use of weighting functions

In this work we consider transport in ordered and disordered porous media using singlephase flow in rigid porous mediaas an example. We defineorder anddisorder in terms of geometrical integrals that arise naturally in the method of volume averaging, and we show that dependent variables for ordered media must generally be defined in terms of thecellular average. The cellular average can be constructed by means of a weighting function, thus transport processes in both ordered and disordered media can be treated with a single theory based on weighted averages. Part I provides some basic ideas associated with ordered and disordered media, weighted averages, and the theory of distributions. In Part II a generalized averaging procedure is presented and in Part III the closure problem is developed and the theory is compared with experiment. Parts IV and V provide some geometrical results for computer generated porous media.Roman Letters A interfacial area of the- interface contained within the macroscopic region, m² - A_e area of entrances and exits for the-phase contained within the macroscopic system, m² - g gravity vector, m/s² - I unit tensor - K traditional Darcy's law permeability tensor, m² - L general characteristic length for volume averaged quantities, m - characteristic length (pore scale) for the-phase - (y) weighting function - m(–y) (y), convolution product weighting function - _v special weighting function associated with the traditional averaging volume - N unit normal vector pointing from the-phase toward the-phase - p pressure in the-phase, N/m² - p0 reference pressure in the-phase, N/m² - p traditional intrinsic volume averaged pressure, N/m² - r0 radius of a spherical averaging volume, m - r position vector, m - r position vector locating points in the-phase, m - averaging volume, m³ - V volume of the-phase contained in the averaging volume, m³ - V _cell volume of a unit cell, m³ - v velocity vector in the-phase, m/s - v traditional superficial volume averaged velocity, m/s - x position vector locating the centroid of the averaging volume or the convolution product weighting function, m - y position vector relative to the centroid, m - y position vector locating points in the-phase relative to the centroid, m Greek Letters indicator function for the-phase - Dirac distribution associated with the- interface - V/V, volume average porosity - mass density of the-phase, kg/m³ - viscosity of the-phase, Ns/m²     

Time averaged temperature distribution in a cylindrical resistor with alternating current

The non-uniform heat generation in a cylindrical resistor crossed by an alternating electric current is considered. The time averaged and dimensionless temperature distribution in the resistor is analytically evaluated. Two dimensionless functions are reported in tables which allow one to determine the time averaged temperature field for arbitrarily chosen values of the physical properties and of the radius of the resistor, of the electric current frequency, of the Biot number and of either the power generated per unit length or the effective electric current.

---

Zeitliche Temperaturverteilung in einem zylinderförmigen Wechselstromwiderstand

Zusammenfassung Es wird ungleichförmige Wärmeerzeugung in einem mit Wechselstrom belasteten Widerstand unterstellt, woraus sich die darin einstellende, zeitlich gemittelte, dimensionslose Temperaturverteilung analytisch berechnen läßt. Zwei tabellierte dimensionslose Funktionen gestatten die Bestimmung dieser Temperaturverteilung für beliebige Werte der Stoff- und Feldparameter, des Widerstandhalbmessers, der elektrischen Frequenz, der Biot-Zahl, sowie der erzeugten Leistung pro Längeneinheit oder des effektiven Stroms.

---

Nomenclature A intregration constant introduced in Eq. (15) - Bi Biot numberhr ₀/ - c speed of light in empty space - c _p specific heat at constant pressure - E electric field - E _z component ofE alongz - E amplitude of the electric field oscillations - electric permittivity - f function ofs and defined in Eq. (22) - function of defined in Eq. (45) - g function ofs and defined in Eq. (34) - h convection heat transfer coefficient - H magnetic field - i imaginary uniti=–1 - I electric current - I _eff effective electric currentI _eff=I/2 - Im imaginary part of a complex number - J current density - J _n Bessel function of first kind and ordern - thermal conductivity - magnetic permeability - ₀ magnetic permeability of free space - q _g power generated per unit volume - time average of the power generated per unit volume - Q time averaged power per unit length - r radial coordinate - R electric resistance per unit length - r ₀ radius of the cylinder - Re real part of a complex number - mass density - s dimensionless radial coordinates=r/r ₀ - s,s integration variables - electric conductivity - t time - T temperature - time averaged temperature - T _f fluid temperature outside the boundary layer - time average of the surface temperature of the cylinder - dimensionless temperature defined in Eq. (27) - x position vector - x arbitrary real variable - x integration variable - Y ₀ Bessel function of second kind and order 0 - z axial coordinate - z unit vector parallel to the axis of the cylinder - angular frequency - dimensionless parameter =r₀ - · modulus of a complex number - equal by definition     

The value of the critical exponent for reaction-diffusion equations in cones

Let D R ^N be a cone with vertex at the origin i.e., D = (0, )x where S ^N–1 and x D if and only if x = (r, ) with r=¦x¦, . We consider the initial boundary value problem: u _t = u+u ^p in D×(0, T), u=0 on Dx(0, T) with u(x, 0)=u ₀(x) 0. Let ₁ denote the smallest Dirichlet eigenvalue for the Laplace-Beltrami operator on and let ₊ denote the positive root of (+N–2) = ₁. Let p ^* = 1 + 2/(N + ₊). If 1 < p < p ^*, no positive global solution exists. If p>p ^*, positive global solutions do exist. Extensions are given to the same problem for u _t=+¦x¦ u ^p .This research was supported in part by the Air Force Office of Scientific Research under Grant # AFOSR 88-0031 and in part by NSF Grant DMS-8 822 788. The United States Government is authorized to reproduce and distribute reprints for governmental purposes not withstanding any copyright notation therein.     

Uniqueness and the maximum principle for quasilinear elliptic equations with quadratic growth conditions

In this paper, we show that the maximum principle holds for quasilinear elliptic equations with quadratic growth under general structure conditions.Two typical particular cases of our results are the following. On one hand, we prove that the equation (1) {ie77-01} where {ie77-02} and {ie77-03} satisfies the maximum principle for solutions in H ¹()L(), i.e., that two solutions u ₁, u ₂H¹() L() of (1) such that u ₁u₂ on , satisfy u ₁u₂ in . This implies in particular the uniqueness of the solution of (1) in H ₀ ¹ ()L().On the other hand, we prove that the equation (2) {ie77-04} where fH^–1() and g(u)>0, g(0)=0, satisfies the maximum principle for solutions uH¹() such that g(u)¦Du|{²L¹(). Again this implies the uniqueness of the solution of (2) in the class uH ₀ ¹ () with g(u)¦Du|{²L¹().In both cases, the method of proof consists in making a certain change of function u=(v) in equation (1) or (2), and in proving that the transformed equation, which is of the form (3) {ie77-05}satisfies a certain structure condition, which using ((v₁ -v ₂)⁺)ⁿ for some n>0 as a test function, allows us to prove the maximum principle.     

The contribution of internal degrees of freedom to the non-Newtonian rheology of model polymer fluids

We report non-equilibrium molecular dynamics simulations of rigid and non-rigid dumbbell fluids to determine the contribution of internal degrees of freedom to strain-rate-dependent shear viscosity. The model adopted for non-rigid molecules is a modification of the finitely extensible nonlinear elastic (FENE) dumbbell commonly used in kinetic theories of polymer solutions. We consider model polymer melts — that is, fluids composed of rigid dumbbells and of FENE dumbbells. We report the steady-state stress tensor and the transient stress response to an applied Couerte strain field for several strain rates. We find that the rheological properties of the rigid and FENE dumbbells are qualitatively and quantitatively similar. (The only exception to this is the zero strain rate shear viscosity.) Except at high strain rates, the average conformation of the FENE dumbbells in a Couette strain field is found to be very similar to that of FENE dumbbells in the absence of strain. The theological properties of the two dumbbell fluids are compared to those of a corresponding fluid of spheres which is shown to be the most non-Newtonian of the three fluids considered.Symbol Definition b dimensionless time constant relating vibration to other forms of motion - F force on center of mass of dumbbell - F _i force on bead i of dumbbell - F force between center of masses of dumbbells and - F _ij force between beads i and j - h vector connecting bead to center of mass of dumbbell - H dimensionless spring constant for dumbbells, in units of / ² - I moment of inertia of dumbbell - J general current induced by applied field - k _B Boltzmann's constant - L angular momentum - m mass of bead, (= m/2) - M mass of dumbbell, g - N number of dumbbells in simulation cell - P translational momentum of center of mass of dumbbell - P pressure tensor - P _xy xy component of pressure tensor - Q separation of beads in dumbbell - Q _eq equilibrium extension of FENE dumbbell and fixed extension of rigid dumbbell - Q ₀ maximum extension of dumbbell - r _ij vector connecting beads i and j - r position vector of center of mass dumbbell - R vector connecting centers of mass of two dumbbells - t time - t ^* dimensionless time, in units of m/ - T ^* dimensionless temperature, in units of /k - u potential energy - u velocity vector of flow field - u _x x component of velocity vector - V volume of simulation cell - X general applied field - strain rate, s^–1 - ^* dimensionless shear rate, in units of /m ² - general transport property - Lennard-Jones potential well depth - friction factor for Gaussian thermostat - shear viscosity, g/cms - ^* dimensionless shear viscosity, in units of m/ ² - ^* dimensionless number density, in units of ^–3 - Lennard-Jones separation of minimum energy - relaxation time of a fluid - angular velocity of dumbbell - orientation angle of dumbbell      

On the closure problem for Darcy's law

In a previous derivation of Darcy's law, the closure problem was presented in terms of an integro-differential equation for a second-order tensor. In this paper, we show that the closure problem can be transformed to a set of Stokes-like equations and we compare solutions of these equations with experimental data. The computational advantages of the transformed closure problem are considerable.Roman Letters A interfacial area of the- interface contained within the macroscopic system, m² - A _e area of entrances and exits for the-phase contained within the macroscopic system, m² - A interfacial area of the- interface contained within the averaging volume, m² - A _e area of entrances and exits for the-phase contained within the averaging volume, m² - B second-order tensor used to respresent the velocity deviation - b vector used to represent the pressure deviation, m^–1 - C second-order tensor related to the permeability tensor, m^–2 - D second-order tensor used to represent the velocity deviation, m² - d vector used to represent the pressure deviation, m - g gravity vector, m/s² - I unit tensor - K C ^–1,–D, Darcy's law permeability tensor, m² - L characteristic length scale for volume averaged quantities, m - characteristic length scale for the-phase, m - l _i i=1, 2, 3, lattice vectors, m - n unit normal vector pointing from the-phase toward the-phase - n _e outwardly directed unit normal vector at the entrances and exits of the-phase - p pressure in the-phase, N/m ² - p intrinsic phase average pressure, N/m² - p –p , spatial deviation of the pressure in the-phase, N/m² - r position vector locating points in the-phase, m - r ₀ radius of the averaging volume, m - t time, s - v velocity vector in the-phase, m/s - v intrinsic phase average velocity in the-phase, m/s - v phase average or Darcy velocity in the \-phase, m/s - v –v , spatial deviation of the velocity in the-phase m/s - V averaging volume, m³ - V volume of the-phase contained in the averaging volume, m³ Greek Letters V /V volume fraction of the-phase - mass density of the-phase, kg/m³ - viscosity of the-phase, Nt/m²     

Combined natural and forced convection in a laminar wall jet along a vertical plate with uniform surface heat flux

The steady state flow and heat transfer characteristics of the combined natural and forced convection in a two dimensional, laminar, incompressible wall jet over a vertical wall are obtained for constant wall heat flux boundary condition. The velocity and temperature distribution are assumed to be power series, where the zeroth term corresponds to that for a plane wall jet in the absence of buoyancy effects. Numerical results for the momentum and thermal series functions are presented for a Prandtl number of 0.73. Wall values of the momentum and thermal series functions are presented for Prandtl numbers ranging from 0.01 to 1000.Nomenclature Gr* modified Grashof number - k thermal conductivity - Nu Nusselt number - Pr Prandtl number - q _w heat flux at the wall - Re Reynolds number - T temperature - u velocity component in x-direction - v velocity component in y-direction - x co-ordinate along the plane wall - y co-ordinate normal to the wall - () gamma function - non-dimensional co-ordinate defined in (6) - non-dimensional temperature - dynamic viscosity - kinematic viscosity - non-dimensional co-ordinate defined in (6) - density - w values at the wall - values at large distances away from the wall     

Flow visualization of compressible vortex structures using density gradient techniques

Mathematical results are derived for the schlieren and shadowgraph contrast variation due to the refraction of light rays passing through two-dimensional compressible vortices with viscous cores. Both standard and small-disturbance solutions are obtained. It is shown that schlieren and shadowgraph produce substantially different contrast profiles. Further, the shadowgraph contrast variation is shown to be very sensitive to the vortex velocity profile and is also dependent on the location of the peak peripheral velocity (viscous core radius). The computed results are compared to actual contrast measurements made for rotor tip vortices using the shadowgraph flow visualization technique. The work helps to clarify the relationships between the observed contrast and the structure of vortical structures in density gradient based flow visualization experiments.Nomenclature a Unobstructed height of schlieren light source in cutoff plane, m - c Blade chord, m - f Focal length of schlieren focusing mirror, m - C _T Rotor thrust coefficient, T/( ² R ⁴) - I Image screen illumination, Lm/m ² - l Distance from vortex to shadowgraph screen, m - n _b Number of blades - p Pressure,N/m ² - p Ambient pressure, N/m ² - r, , z Cylindrical coordinate system - r _c Vortex core radius, m - Non-dimensional radial coordinate, (r/r _c ) - R Rotor radius, m - Tangential velocity, m/s - Specific heat ratio of air - Circulation (strength of vortex), m ²/s - Non-dimensional quantity, ² 8²p r _c ² - Refractive index of fluid medium - ₀ Refractive index of fluid medium at reference conditions - Gladstone-Dale constant, m ³/kg - Density, kg/m ³ - Density at ambient conditions, kg/m ³ - Non-dimensional density, (/ ) - Rotor solidity, (n _b c/ R) - Rotor rotational frequency, rad/s     

Direct measurement of the density field using high speed differential interferometry

The optical method presented here is based on Wollaston prism differential interferometry using a white light source. It yields high-speed, instantaneous interferograms which directly display the isochoric lines of an unsteady, two-dimensional flow. The setup used is equivalent to conventional reference beam interferometric systems, but remains differential since one of the beams — the reference one — lies inside the undisturbed upstream flow. The method was used to obtain an instantaneous, high speed display of the unsteady flow around a cylinder spanning the test section.List of symbols d Cylinder diameter - t Time - t Interval of time between two consecutive interferograms - M Mach number - Density - P Pressure - P Pressure fluctuation - Angle of the prisms making up the birefringent system - Birefringent angle = () - gl Wavelength - n ₀ Ordinary index of the crystal - n _e Extraordinary index of the crystal - D Diameter of the spherical mirror - R Radius of the curvature of the spherical mirror - i Fringe width - 2g prism thickness - X Distance between the two beams interfering at the level of the spherical mirror The quantities relating to upstream conditions are indexed      

Flow in porous media III: Deformable media

Stokes flow in a deformable medium is considered in terms of an isotropic, linearly elastic solid matrix. The analysis is restricted to steady forms of the momentum equations and small deformation of the solid phase. Darcy's law can be used to determine the motion of the fluid phase; however, the determination of the Darcy's law permeability tensor represents part of the closure problem in which the position of the fluid-solid interface must be determined.Roman Letters A interfacial area of the- interface contained within the macroscopic system, m² - A interfacial area of the- interface contained within the averaging volume, m² - A _e area of entrances and exits for the-phase contained within the macroscopic system, m² - A ^* interfacial area of the- interface contained within a unit cell, m² - A _e ^* area of entrances and exits for the-phase contained within a unit cell, m² - E Young's modulus for the-phase, N/m² - e i unit base vectors (i = 1, 2, 3) - g gravity vector, m²/s - H height of elastic, porous bed, m - k unit base vector (=e ₃) - characteristic length scale for the-phase, m - L characteristic length scale for volume-averaged quantities, m - n unit normal vector pointing from the-phase toward the-phase (n = -n ) - p pressure in the-phase, N/m² - P p – g·r, N/m² - r ₀ radius of the averaging volume, m - r position vector, m - t time, s - T total stress tensor in the-phase, N/m² - T ⁰ hydrostatic stress tensor for the-phase, N/m² - u displacement vector for the-phase, m - V averaging volume, m₃ - V volume of the-phase contained within the averaging volume, m³ - v velocity vector for the-phase, m/s Greek Letters V /V, volume fraction of the-phase - mass density of the-phase, kg/m³ - shear coefficient of viscosity for the-phase, Nt/m² - first Lamé coefficient for the-phase, N/m² - second Lamé coefficient for the-phase, N/m² - bulk coefficient of viscosity for the-phase, Nt/m² - T –T ⁰ , a deviatoric stress tensor for the-phase, N/m²     

Shear viscosity behavior of highly concentrated suspensions at low and high shear-rates

A method is proposed for determining the shear viscosity behavior of highly concentrated suspensions at low and high shear-rates through the use of a formulation that is a function of three parameters signifying the effects of particle size distribution. These parameters are the intrinsic viscosity [], a parametern that reflects the level of particle association at the initiation of motion and the maximum packing concentration _m. The formulation reduces to the modified Eilers equation withn = 2 for high shear rates. An analytical method was used for the calculation of maximum packing concentration which was subsequently correlated with the experimental values to account for the surface induced interaction of particles with the fluid. The calculated values of viscosities at low and high shear-rates were found to be in good agreement with various experimental data reported in literature. A brief discussion is also offered on the reliability of the methods of measuring the maximum packing concentration. _r = /₀ relative viscosity of the suspension - volumetric concentration of solids - k _n coefficient which characterizes a specific effect of particle interactions - _m maximum packing concentration - _r,0 relative viscosity at low shear-rates - [] intrinsic viscosity - n, n parameter that reflects the level of particle interactions at low and high shear-rates, respectively - _r, relative viscosity at high shear-rates - (_m)_s, (_m)_i, (_m)_l packing factors for small, intermediate and large diameter classes - v _s, v_i, v_l volume fractions of small, intermediate and large diameter classes, respectively - _si, _sl coefficient to be used in relating a smaller to an intermediate and larger particle group, respectively - _is, _il coefficient to be used in relating an intermediate to a smaller and larger particle group, respectively - _ls, _li coefficient to be used in relating a larger to a smaller and intermediate particle group, respectively - _m0 maximum packing concentration for binary mixtures - _m,e measured maximum packing concentration - _m,c calculated maximum packing concentration     

The relaxation of a double-well energy

This paper studies coherent, energy-minimizing mixtures of two linearly elastic phases with identical elastic moduli. We derive a formula for the relaxed or macroscopic energy of the system, by identifying microstructures that minimize the total energy when the volume fractions and the average strain are fixed. If the stress-free strains of the two phases are incompatible then the relaxed energy is nonconvex, with double-well structure. An optimal microstructure always exists within the class of layered mixtures. The optimal microstructure is generally not unique, however; we show how to construct a large family of optimal, sequentially laminated microstructures in many circumstances. Our analysis provides a link between the work of Khachaturyan and Roitburd in the metallurgical literature and that of Ball, James, Pipkin, Lurie, and Cherkaev in the recent mathematical literature. We close by explaining why the corresponding problem for three or more phases is fundamentally more difficult.Supported in part by ARO contract DAAL03-89-K-0039, DARPA contract F49620-87-C-0065, ONR grant N00014-88-K-0279, NSF grant DMS-8701895 and AFOSR grant 90-0090     

Drag reduction by polymer solutions in a riblet-lined pipe

The flow of 3 to 100 wppm aqueous solutions of a polyethyleneoxide polymer,M _w=6.2×;10⁶, was studied in a 10.2 mm i.d. pipe lined with 0.15 mm V-groove riblets, at diametral Reynolds numbers from 300 to 150000. Measurements in the riblet pipe were accompanied by simultaneous measurements in a smooth pipe of the same diameter placed in tandem. The chosen conditions provided turbulent drag reductions from zero to the asymptotic maximum possible. The onset of polymer-induced drag reduction in the riblet pipe occurred at the same wall shear stress, * _w =0.65 N/m², as that in the smooth pipe. After onset, the polymer solutions in the riblet pipe initially exhibited linear segments on Prandtl-Karman coordinates, akin to those seen in the smooth pipe, with specific slope increment . The maximum drag reduction observed in the riblet pipe was independent of polymer concentration and well below the asymptotic maximum drag reduction observed in the smooth pipe. Polymer solution flows in the riblet pipe exhibited three regimes: (i) Hydraulically smooth, in which riblets induced no drag reduction, amid varying, and considerable, polymer-induced drag reduction; this regime extended to non-dimensional riblet heightsh ⁺<5 in solvent andh ⁺<10 in polymer solutions. (ii) Riblet drag reduction, in which riblet-induced flow enhancementR>0; this regime extended from 5<h ⁺<22 in solvent and from 10<h ⁺<30 in the 3 wppm polymer solution, with respective maximaR=0.6 ath ⁺=14 andR=1.6 ath ⁺=21. Riblet drag reduction decreased with increasing polymer concentration and increasing polymer-induced flow enhancement S. (iii) Riblet drag enhancement, whereinR<0; this regime extended for 22<h ⁺<110 in solvent, withR;–2 forh ⁺>70, and was observed in all polymer solutions at highh ⁺, the more so as polymer-induced drag reduction increased, withR<0 for allS>8. The greatest drag enhancement in polymer solutions,R=–7±1 ath ⁺=55 whereS=20, considerably exceeded that in solvent. Three-dimensional representations of riblet- and polymer-induced drag reductions versus turbulent flow parameters revealed a hitherto unknown dome region, 8<h ⁺<31, 0<S<10, 0<R<1.5, containing a broad maximum at (h ⁺,S,R) = (18, 5, 1.5). The existence of a dome was physically interpreted to suggest that riblets and polymers reduce drag by separate mechanisms.     

Heat transfer from laminar flow in ducts with elliptic cross-section

Summary The cooling of a hot fluid in laminar Newtonian flow through cooled elliptic tubes has been calculated theoretically. Numerical data have been computed for the two values 1.25 and 4 of the axial ratio of the elliptic cross-section . For =1.25 the influence of non-zero thermal resistance between outmost fluid layer and isothermal surroundings has also been investigated. Special attention has been given to the distribution of heat flux around the perimeter; when increases the flux varies more with the position at the circumference. This positional dependence becomes less pronounced, however, as the (position-independent) thermal resistance of the wall increases.Flattening of the conduit, while maintaining its cross-sectional area constant, improves the cooling. Comparison with rectangular pipes shows that this improvement is not as marked with elliptic as with rectangular pipes.Nomenclature A _k =A _{m, n} coefficients of expansion (6) - a, b half-axes of ellipse, b<a - a _p =a _{r, s} coefficients of representation (V) - D hydraulic diameter, = 4S/P; S = cross-sectional area, P = perimeter - D _e equivalent diameter, according to (13) - n coordinate (outward) normal to the tube wall - T temperature of fluid - T _i temperature of fluid at the inlet - T _s temperature of surroundings - v ₀ mean velocity of fluid - v _z longitudinal velocity of fluid - x, y carthesian coordinates coinciding with axes of ellipse - z coordinate in flow direction - , dimensionless half-axes of ellipse, =a/D and =b/D - _t heat transfer coefficient from fluid at bulk temperature to surroundings; equation (11) - _w heat transfer coefficient at the wall; equation (3) - axial ratio of ellipse, = a/b = / - , , , dimensionless coordinates; =x/D, =y/D, =z/D, =n/D - dimensionless temperature, = (T–T _s)/(T _i–T _s) - ₀ cup-mixing mean value of ; equation (10) - thermal conductivity of fluid - _m,n = _k eigenvalue - c volumetric heat capacity of fluid - _{m, n} = _k = _k eigenfunction; equations (6) and (I) - Nu total Nusselt number, = _t D/ - Nusselt number at large distance from the inlet - Nu _w wall Nusselt number, = _w D/, based on _w - Pé Péclet number, = ₀ Dc/     

On the effects of a periodic, spanwise variation of suction upon asymptotic suction flow

Summary The effects of superposing streamwise vorticity, periodic in the lateral direction, upon two-dimensional asymptotic suction flow are analyzed. Such vorticity, generated by prescribing a spanwise variation in the suction velocity, is known to play an important role in unstable and turbulent boundary layers. The flow induced by the variation has been obtained for a freestream velocity which (i) is steady, (ii) oscillates periodically in time, (iii) changes impulsively from rest. For the oscillatory case it is shown that a frequency can exist which maximizes the induced, unsteady wall shear stress for a given spanwise period. For steady flow the heat transfer to, or from a wall at constant temperature has also been computed.Nomenclature (x, y, z) spatial coordinates - (u, v, w) corresponding components of velocity - (, , ) corresponding components of vorticity - t time - stream function for v and w - v _w mean wall suction velocity - nondimensional amplitude of variation in wall suction velocity - characteristic wavenumber for variation in direction of z - T temperature - P pressure - density - coefficient of kinematic viscosity - coefficient of thermal diffusivity - (/v _w)² - frequency of oscillation of freestream velocity - nondimensional amplitude of freestream oscillation - /v _w ² - z z - y –v _w y/ - v _w ² t/4 - /v _w - U ₀ characteristic freestream velocity - u/U ₀ - coefficient of viscosity - _w wall shear stress - Prandtl number (/) - q heat transfer to wall - T _w wall temperature - T (T _w–T)/(T _w–)     

Control of low-speed turbulent separated flow using jet vortex generators

A parametric study has been performed with jet vortex generators to determine their effectiveness in controlling flow separation associated with low-speed turbulent flow over a two-dimensional rearward-facing ramp. Results indicate that flow-separation control can be accomplished, with the level of control achieved being a function of jet speed, jet orientation (with respect to the free-stream direction), and jet location (distance from the separation region in the free-stream direction). Compared to slot blowing, jet vortex generators can provide an equivalent level of flow control over a larger spanwise region (for constant jet flow area and speed).Nomenclature C _p pressure coefficient, 2(P-P_)/V ² - C _Q total flow coefficient, Q/ v - D ₀ jet orifice diameter - Q total volumetric flow rate - R Reynolds number based on momentum thickness - u fluctuating velocity component in the free-stream (x) direction - V free-stream flow speed - VR ratio of jet speed to free-stream flow speed - x coordinate along the wall in the free-stream direction - jet inclination angle (angle between the jet axis and the wall) - jet azimuthal angle (angle between the jet axis and the free-stream direction in a horizontal plane) - boundary-layer thickness - momentum thickness - lateral distance between jet orifices A version of this paper was presented at the 12th Symposium on Turbulence, University of Missouri-Rolla, 24–26 Sept. 1990     

Deformation to breaking of deep water gravity waves

The results of laboratory observations of the deformation of deep water gravity waves leading to wave breaking are reported. The specially developed visualization technique which was used is described. A preliminary analysis of the results has led to similar conclusions than recently developed theories. As a main fact, the observed wave breaking appears as the result of, first, a modulational instability which causes the local wave steepness to approach a maximum and, second, a rapidly growing instability leading directly to the breaking.List of symbols L total wave length - H total wave height - crest elevation above still water level - trough depression below still water level - wave steepness =H/L - crest steepness =/L - trough steepness =/L - F ₁ forward horizontal length from zero-upcross point (A) to wave crest - F ₂ backward horizontal length from wave crest to zero-downcross point (B) - crest front steepness =/F ₁ - crest rear steepness =/F ₂ - vertical asymmetry factor=F ₂/F ₁ (describing the wave asymmetry with respect to a vertical axis through the wave crest) - µ horizontal asymmetry factor=/H (describing the wave asymmetry with respect to a horizontal axis: SWL) - T ₀ wavemaker period - L ₀ theoretical wave length of a small amplitude sinusoïdal wave generated at T _inf0 ^sup–1 frequency - ₀ average wave height     

Eine analytische Näherungslösung für die eingefrorene laminare Grenzschichtströmung eines binären Gemisches

Zusammenfassung Für die eingefrorene laminare Grenzschichtströmung eines teilweise dissoziierten binären Gemisches entlang einer stark gekühlten ebenen Platte wird eine analytische Näherungslösung angegeben. Danach läßt sich die Wandkonzentration als universelle Funktion der Damköhler-Zahl der Oberflächenreaktion angeben. Für das analytisch darstellbare Konzentrationsprofil stellt die Damköhler-Zahl den Formparameter dar. Die Wärmestromdichte an der Wand bestehend aus einem Wärmeleitungs- und einem Diffusionsanteil wird angegeben und diskutiert. Das Verhältnis beider Anteile läßt sich bei gegebenen Randbedingungen als Funktion der Damköhler-Zahl ausdrücken.

---

An analytical approximation for the frozen laminar boundary layer flow of a binary mixture

An analytical approximation is derived for the frozen laminar boundary layer flow of a partially dissociated binary mixture along a strongly cooled flat plate. The concentration at the wall is shown to be a universal function of the Damkohler-number for the wall reaction. The Damkohlernumber also serves as a parameter of shape for the concentration profile which is presented in analytical form. The heat transfer at the wall depending on a conduction and a diffusion flux is derived and discussed. The ratio of these fluxes is expressed as a function of the Damkohler-number if the boundary conditions are known.

---

Formelzeichen A Atom - A₂ Molekül - C Konstante in Gl. (20) - c₁=1/(2C) Konstante in Gl. (35) - c_p spezifische Wärme bei konstantem Druck - D binärer Diffusionskoeffizient - Ec=u ² /(2h_f) Eckert-Zahl - h spezifische Enthalpie - h_t=h+u²/2 totale spezifische Enthalpie - h _A ⁰ spezifische Dissoziationsenthalpie - K_w Reaktionsgeschwindigkeitskonstante der heterogenen Wandreaktion - 1= /( ) Champman-Rubesin-Parameter - Le=Pr/Sc Lewis-Zahl - M Molmasse - p statischer Druck - Pr= c_pf/ Prandtl-Zahl - q_w Wärmestromdichte an der Wand - q_cw, q_dw Wärmeleitungsbzw. Diffusionsanteil der Wärmestromdichte an der Wand - universelle Gaskonstante - R=/(2M_a) individuelle Gaskonstante der molekularen Komponente - Re_x= u x/ Reynolds-Zahl - Sc=/( D) Schmidt-Zahl - T absolute Temperatur - T_d=h _A ⁰ /R charakteristische Dissoziationstemperatur - u, v x- und y-Komponenten der Geschwindigkeit - U=u/u normierte x-Komponente der Geschwindigkeit - x, y Koordinaten parallel und senkrecht zur Platte Griechische Symbole - =A/ Dissoziationsgrad - Grenzschichtdicke - ₂ Impulsverlustdicke - Damköhler-Zahl der Oberflächenreaktion - =T/T normierte Temperatur - =y/ normierter Wandabstand - Wärmeleitfähigkeit - dynamische Viskosität - , ^* Ähnlichkeitskoordinaten - Dichte - Schubspannung Indizes A auf ein Atom bezogen - M auf ein Molekül bezogen - f auf den eingefrorenen Zustand bezogen - w auf die Wand bezogen - auf den Außenrand der Grenzschicht bezogen     

Flow in porous media I: A theoretical derivation of Darcy's law

Stokes flow through a rigid porous medium is analyzed in terms of the method of volume averaging. The traditional averaging procedure leads to an equation of motion and a continuity equation expressed in terms of the volume-averaged pressure and velocity. The equation of motion contains integrals involving spatial deviations of the pressure and velocity, the Brinkman correction, and other lower-order terms. The analysis clearly indicates why the Brinkman correction should not be used to accommodate ano slip condition at an interface between a porous medium and a bounding solid surface.The presence of spatial deviations of the pressure and velocity in the volume-averaged equations of motion gives rise to aclosure problem, and representations for the spatial deviations are derived that lead to Darcy's law. The theoretical development is not restricted to either homogeneous or spatially periodic porous media; however, the problem ofabrupt changes in the structure of a porous medium is not considered.Roman Letters A interfacial area of the - interface contained within the macroscopic system, m² - A _e area of entrances and exits for the -phase contained within the macroscopic system, m² - A interfacial area of the - interface contained within the averaging volume, m² - A ^* interfacial area of the - interface contained within a unit cell, m² - Ae area of entrances and exits for the -phase contained within a unit cell, m² - B second order tensor used to represent the velocity deviation (see Equation (3.30)) - b vector used to represent the pressure deviation (see Equation (3.31)), m^–1 - d distance between two points at which the pressure is measured, m - g gravity vector, m/s² - K Darcy's law permeability tensor, m² - L characteristic length scale for volume averaged quantities, m - characteristic length scale for the -phase (see Figure 2), m - characteristic length scale for the -phase (see Figure 2), m - n unit normal vector pointing from the -phase toward the -phase (n =–n ) - n _e unit normal vector for the entrances and exits of the -phase contained within a unit cell - p pressure in the -phase, N/m² - p intrinsic phase average pressure for the -phase, N/m² - p –p , spatial deviation of the pressure in the -phase, N/m² - r ₀ radius of the averaging volume and radius of a capillary tube, m - v velocity vector for the -phase, m/s - v phase average velocity vector for the -phase, m/s - v intrinsic phase average velocity vector for the -phase, m/s - v –v , spatial deviation of the velocity vector for the -phase, m/s - V averaging volume, m³ - V volume of the -phase contained within the averaging volume, m³ Greek Letters V/V, volume fraction of the -phase - mass density of the -phase, kg/m³ - viscosity of the -phase, Nt/m² - arbitrary function used in the representation of the velocity deviation (see Equations (3.11) and (B1)), m/s - arbitrary function used in the representation of the pressure deviation (see Equations (3.12) and (B2)), s^–1