超疏水碱式碳酸钴纳米线薄膜的制备及抗腐蚀性

以镍为基底,采用水热法在其表面制得碱式碳酸钴纳米线薄膜,用十二烷基硫醇进行表面修饰后其表现出超疏水性,水滴在其表面的接触角达到152.3°,滚动角接近5°.研究结果表明,薄膜表面微纳米阶层结构及低表面物质的协同作用使其呈超疏水性.与普通镍片和硫醇修饰前的碱式碳酸钴纳米线薄膜相比,超疏水碱式碳酸钴纳米线薄膜具有更好的抗腐蚀性.相关研究有望为超疏水金属表面的制备及其抗腐蚀性研究提供思路.     

聚苯硫醚超疏水复合涂层的制备与性能

利用工业原料聚苯硫醚微粉和疏水性二氧化硅纳米粉末,采用喷涂法在瓷砖表面制备了疏水复合涂层.研究了热处理温度、组分配比对涂层表面形貌、粗糙度和接触角的影响,发现随着热处理温度升高,涂层表面粗糙度增大,随着疏水性二氧化硅含量的增加,由于表面聚集的疏水性二氧化硅增多,涂层疏水性增强,在热处理温度为280℃、疏水性二氧化硅与聚苯硫醚质量比为1∶1时,可获得超疏水涂层,涂层的接触角大于150°,滚落角小于4°,pH值为1～14的水溶液在其表面都具有很高的接触角.超疏水涂层具有良好的自清洁效果,并且经落沙法实验测定,超疏水涂层耐刮伤性能良好.     

浸润性可调的导电聚苯胺/聚丙烯腈同轴纳米纤维

聚苯胺(PANI)因其具有可调的导电性、优异的化学稳定性、简单的制备方法等特点, 在化学电源、抗静电涂层、电磁屏蔽材料、抗腐蚀、传感器等领域具有广泛的应用前景[^1~4]. 由于聚苯胺的刚性分子链使得聚苯胺几乎不溶不熔, 难以加工应用, 因此, 将导电聚合物直接制成纳米纤维一直是合成纤维界所希望的目标之一. 此外, 由于材料尺度的减小, 使纳米材料的表面与界面性质,尤其是表面浸润性变得更为突出.浸润性是固体表面的重要特征之一, 它主要由表面的化学组成和微观结构共同决定^[5,6]. 可调的浸润性在超疏水材料、药物传输、仿生材料和微流体等领域具有重要的应用价值^[7~10] , 引起人们广泛关注.     

可粘贴超疏水薄膜的制备

通过聚二甲基硅氧烷(PDMS)与碳纤维织物复合, 采用模板法在PDMS聚合物表面构筑微阵列结构, 制备了一种具有可重复粘贴性的超疏水薄膜. 研究结果表明, 该薄膜微结构表面的接触角为154°, 滚动角为14°, 具有低黏附的超疏水特性. 而PDMS与碳纤维织物的紧密结合, 赋予了超疏水薄膜较高的黏接力和力学性能, 断裂强度达到116.96 MPa. 所制备的超疏水薄膜可粘贴于多种材料表面, 同时经过30 d的长时间粘贴以及50次的循环粘贴后, 该薄膜依然保持着较高的黏附性能及超疏水特征, 表明超疏水薄膜具有良好的力学稳定性及耐久性, 满足长时间可重复使用的要求, 可应用于对破损超疏水涂层的快速、 大面积粘贴修复.     

波纹状银纳米线的制备及其SERS性能研究

首先通过传统的多元醇方法合成了表面光滑的银纳米线,然后利用Fe（NO₃）₃作为刻蚀剂在室温条件下对合成的银纳米线进行刻蚀得到了具有波纹状表面的银纳米线. 通过扫描电镜（SEM）分析表明：银纳米线的表面粗糙程度随着刻蚀剂量的增加而增加,但过量的刻蚀剂又会导致纳米线的断裂甚至形成球状颗粒;当刻蚀剂的量为100 μL时,获得了波纹状表面的银纳米线. 对结晶紫（CV）的表面增强拉曼光谱（SERS）结果表明,这种波纹状银纳米线的拉曼信号强度比表面光滑的银纳米线提高了约5倍,其检测限可低至10^-10 mol/L. 此外,这种优势还可以延伸到敏感性检测10^-9 mol/L的对巯基吡啶（4-Mpy）分子,可以作为一种普适、有效的SERS活性基底.     

超疏水超亲油铜网的制备及其在油水分离中的应用

以铜网为基底,通过浸涂法在其表面制得超疏水超亲油有机-无机复合薄膜,水滴、油滴在其表面的接触角分别为152°和10°。 线性低密度聚乙烯-SiO₂纳米球构成的复合阶层结构及低表面能线性低密度聚乙烯涂层的协同作用使铜网产生独特的润湿性。 该铜网具有很好的自清洁性和抗腐蚀性,可用于油水混合物的有效分离。 与传统方法相比,该方法制备超疏水-超亲油薄膜方法简单、成本低、无氟,有望在实践中得到应用。     

透明超疏水材料的制备及其应用

超疏水材料由于其独特的非浸润性引起人们的广泛关注,近年来得到迅猛发展,各种适用于不同领域的功能性超疏水表面应运而生。其中,透明超疏水材料因其在光学领域的特殊贡献受到人们的青睐。透明疏水涂层技术对于实际应用具有重要的意义,透明涂层不仅可以满足光学器件防护的高透光率,还可以维持防护本体的基本外观,在自清洁、防污、防冰防雾、防腐蚀等领域都展示出广阔的应用前景。本文系统地阐述了超疏水表面以及其中功能性的透明超疏水表面的最新进展、表面的设计、制造和重要应用。尽管已经取得了重大进展,但是目前超疏水材料在耐久性方面还存在诸多问题,例如,容易被机械外力破坏、极端环境下表面的超疏水性质不稳定以及老化等问题,限制了透明疏水涂层技术的大范围应用。在未来的研究中,一方面继续丰富相关的理论知识,为透明疏水涂层技术的应用提供更多的理论支持,另一方面,提高涂层的透明度和机械耐久性能仍是未来研究的重中之重。     

超疏水聚硅氧烷涂层的制备及其性能

采用溶胶-凝胶法,以甲基三乙氧基硅烷(MTES)为有机硅前驱体,通过酸-碱催化水解-缩合得到聚有机硅氧烷凝胶,经浸涂-提拉成膜技术在玻璃表面制备超疏水聚硅氧烷涂层。通过红外光谱(FT-IR)、水接触角(WCA)和场发射扫描电子显微镜(FE-SEM)等分析技术对涂层进行了结构表征、疏水性测试和表面形貌观察。结果表明,涂层内部形成带有甲基和残余硅羟基基团的网络结构。当n(MTES)∶n(EtOH)∶n(H2O)分别为1∶35∶8和1∶45∶8时,在室温制备的涂层对水的接触角可分别高达160°和162°,滚动角均低至7°,并且涂层在250℃以下的热处理过程中,其疏水性基本保持不变。FE-SEM观察证实了涂层表面分布着许多孔径为0.5～1.0μm的微孔和粒径为50～100 nm的纳米颗粒聚集体,具有微-纳米尺寸相结合的双重结构。此外涂层还具有较高的透明性、对腐蚀性液体具有超疏水性。研制得到的超疏水涂层有望用于玻璃、织物、金属和塑料等基底表面作为保护和防腐蚀涂膜。     

液相法制备具有双尺寸粗糙度的超疏水铜表面

基于简单的液相法,以硫代硫酸钠和氯化铜为原料在铜片表面上构筑了具有微/纳米双尺寸粗糙度的硫化铜膜.用X射线衍射(XRD)仪、扫描电镜(SEM)、能量色散X射线(EDX)光谱仪及光学视频接触角仪对处理前后的铜表面进行了表征和分析.处理后的超亲水铜表面经硬脂酸修饰后具有超疏水效应,静态接触角高达161°,5μL水滴滚动角低至2.5°左右.超疏水性能归因于表面具有双尺寸粗糙度和低表面能的硬脂酸.该方法简单,无需复杂制备过程和苛刻设备,所得超疏水铜表面具有优异的不粘附性、长时间储存的稳定性和一定的耐摩擦性能.     

二氧化硅纳米颗粒/硅树脂复合超疏水功能涂层的制备和性能研究

将二氧化硅纳米颗粒和硅树脂制成混合液,采用喷涂法(spray-coating)制备出了具备超疏水性的复合涂层.研究了二氧化硅、硅树脂不同含量配比对涂层疏水性能的影响,结果表明复合涂层的接触角随二氧化硅含量的增加而增加.在二氧化硅含量大于3%(质量分数)时,涂层显现超疏水性;当二氧化硅含量为3%(质量分数)、硅树脂含量为7%(质量分数)时,涂层与水的接触角达到151.6°,滚动角接近0°.通过扫描电子显微镜(SEM)观察涂层表面的微观结构,发现超疏水性的涂层具备微-纳复合阶层结构,类球状突起粒径在5μm左右,类球状突起上分布纳米团聚颗粒,直径约为50 nm.这种类似荷叶表面的微(纳复合阶层结构,结合硅树脂的低表面能,使得复合涂层具备了超疏水性能.     

Hydrocarbon versus fluorocarbon in the electrodeposition of superhydrophobic polymer films

To elaborate on superhydrophobic surfaces, we report the electrochemical synthesis, surface morphology, and wettability of hydrocarbon conductive polymer films obtained by the electrodeposition of polythiophene, poly(3,4-ethylenedioxythiophene) (i.e., PEDOT), and poly(3,4-ethylenedioxypyrrole) (i.e., PEDOP) derivatives. Highly hydrophobic films were obtained from n-C(14)H(29) and n-C(8)H(17) chains in the cases of polythiophenes and PEDOP, respectively. By contrast, superhydrophobic films were formed by the deposition of PEDOT substituted with n-C(10)H(21) chains (PEDOT-methyl undecanoate): static contact angle ≈ 160.6°, hysteresis ≈ 2°, and sliding angle ≈ 3°. Their surface properties were compared to those of previously reported fluorinated analogues. The water-repellent properties of PEDOT-methyl undecanoate were similar to the best surface properties obtained with fluorinated monomers. Even if the main approach for the chemical factor to build up superhydrophobic surfaces is via a coating of a fluorinated compound, this work confirms that the formation of fractal surfaces is able to achieve super-anti-wetting properties within a hydrocarbon series (less expensive with a favorable ecotoxic approach), and it opens a new path to bioinspired surfaces.     

聚酯织物表面耐用超疏水涂层的制备及在油水分离中的应用

使用在含有甲基MQ(M:单官能团Si-O单元R₃SiO_1/2, Q:四官能团Si-O单元SiO₂)硅树脂与疏水SiO₂的二甲苯溶液中浸渍的方法,在聚酯织物表面制备了耐用超疏水涂层。经过处理后,微米级聚酯纤维表面被紧密的疏水纳米颗粒包裹,通过这种方法降低了纤维的表面能。聚酯织物展现出良好的超疏水特性,与水滴的静态接触角为156°,滚动角为5°。得到的超疏水聚酯织物在机械磨损、酸碱环境及紫外线照射条件下,表现出了良好的稳定性。此外,用超疏水聚酯织物作为过滤材料得到的油水分离效率达99%以上。该方法为大面积工业制备超疏水织物提供了新的思路。     

丙烯酸水溶液聚合法制备PTFE/PAA/Nafion膜及其性能

采用廉价的多孔聚四氟乙烯(PTFE)膜作为基底, 用少量的Nafion与PTFE膜复合可制备低成本的质子膜. 但疏水性的PTFE膜与亲水性的Nafion膜结合性不佳. 基于此, 本文对疏水性的PTFE膜材料表面进行设计, 先采用丙烯酸对疏水性的PTFE膜表面进行亲水性改性, 再喷涂亲水性Nafion膜, 完成低成本PTFE/PAA/Nafion膜的制备. 实验结果表明, 改性前的PTFE膜材料水接触角为150°, 改性后的膜接触角变为55.6°, 亲水性大幅上升, 膜的机械强度和尺寸稳定性(断裂强度为25.2 MPa, 80 ℃下的溶胀率为11.9%)均优于Nafion117膜, 而 Nafion用量则节省了60%. PTFE/PAA/Nafion膜具有高质子导通率(80 ℃下达到131.9 mS/cm), 接近于Nafion117膜, 最大功率密度可以达到404.2 mW/cm².     

Highly transparent superhydrophobic thin film with low refractive index prepared by one-step coating of modified silica nanoparticles

An easy and effective method to prepare superhydrophobic thin film has been developed. The film with optically transparent and low refractive index was composed by one-step coating with modified silica nanoparticles. The silica nanoparticles were prepared by sol–gel process of hydrolysis and condensation of alkoxysilane compounds and then surface modification silica nanoparticles, 50 ± 10 nm, were accomplished using methoxytrimethylsilane (MOTMS). Water contact angle of film increased with the weight of MOTMS of silica sol. When the weight of MOTMS was optimized, the water contact angle and sliding angle of film were 152.8° and less than 10°, respectively. The transmittance of film was also increased as compared to the un-coated microscope glass slide, from 91 to 93.5 %. The refractive index of the film was approximately 1.09 as measured by ellipsometer. The superhydrphobic thin film was also successfully made by using spray coating and the water contact angle of this film was more than 160°. Surface morphology of difference coating methods, dip and spray, were studied. Our result suggests that the film can be applied for superhydrophobicity and optical applications.     

不饱和糖功能单体接枝聚氨酯膜的制备及其血液相容性

通过葡萄糖、丙烯酸羟乙酯和丁二胺反应,制备了含不饱和双键的糖基功能单体。 采用傅里叶红外光谱和核磁共振氢谱对合成的产物进行结构表征确定。 采用紫外光引发接枝聚合技术,将制备的不饱和糖单体接枝聚合到聚氨酯膜的表面,以衰减全反射模式下傅里叶红外光谱对表面接枝反应进行了确认。 通过静态水接触角实验和血小板黏附实验,分别对改性聚氨酯膜表面的亲水性和血液相容性进行了研究,结果表明,改性聚氨酯膜表面的接触角从86°降低到45°,血小板的粘附量由14.36×10³ cells/mm²减少到2.57×10³ cells/mm²,亲水性明显增强,血液相容性显著改善。     

水热法制备铝合金超疏水表面及电化学性能研究

在金属表面构建超疏水膜层是一种有效的防腐技术,本文采用水热处理和自组装技术在铝合金表面构建了超疏水膜层来提升铝合金的耐蚀性能. 通过对不同水热时间下制备的铝合金超疏水表面的电化学性能以及表面形貌进行测试分析,发现当水热反应时间为6 h时,制备的超疏水铝合金超疏水性和电化学性能达到最佳,接触角能达到155.5^o,在模拟海水溶液中保护效率能达到99.6%.     

Permeability of hydrophilic and hydrophobic Shirasu-porous-glass (SPG) membranes to pure liquids and its microstructure

Morphological properties of hydrophilic and hydrophobic Shirasu-porous-glass (SPG) membranes were investigated over a wide range of mean pore sizes (0.252–20.3 μm) by liquid permeability measurements, scanning electron microscopy and Hg porosimetry. Hydrophobic modification of membrane surface was made by surface coating with silicone resin. The results are discussed using the non-uniform capillary bundle model of membrane permeability. The mean pore tortuosity of 1.28 was kept constant over the whole range of mean pore sizes investigated. The SEM images confirmed that the geometry of pore network was similar for all SPG membranes, irrespective of their mean pore size. The span of pore size distribution ranged from 0.28 to 0.68 and the number of pores per unit cross-sectional membrane area from 10⁹ to 10¹³ m⁻². The membrane resistance was unchanged after surface treatment with silicone resin, which means that the pores were not plugged by the resin, even in the submicron range of mean pore sizes.     

钒钨酸盐/刚果红电致变色复合膜及器件研究

应用Layer-by-Layer自组装技术,采用聚乙烯亚胺(PEI)阳离子将无机电致变色材料[P2W15V3O62]8-(P2W15V3)阴离子与刚果红(CR)阴离子通过静电引力复合,构筑了复合膜[PEI/P2W15V3/PEI/CR]20及对比膜[PEI/P2W15V3]20.利用扫描电子显微镜、紫外-可见吸收光谱和电化学工作站研究了复合膜的形貌与电致变色性能.对比研究表明,复合膜可实现浅红色-蓝紫色-浅红色的可逆颜色调变,且保持了[P2W15V3O62]8-阴离子的电致变色性能,光反差22.55%,着色效率122.67 cm2/C.复合膜循环测试400圈后透过率(500 nm)处损耗仅为6.94%,稳定性良好;由复合膜组装的电致变色器件也实现了由浅红色到蓝紫色的颜色变化.本研究可为解决多酸电致变色材料颜色变化单一的问题提供参考.     

Highly transparent superhydrophobic surfaces from the coassembly of nanoparticles (≤100 nm)

We report a simple and versatile approach to creating a highly transparent superhydrophobic surface with dual-scale roughness on the nanoscale. 3-Aminopropyltrimethoxysilane (APTS)-functionalized silica nanoparticles of two different sizes (100 and 20 nm) were sequentially dip coated onto different substrates, followed by thermal annealing. After hydrophobilization of the nanoparticle film with (heptadecafluoro-1,1,2,2-tetrahydrodecyl)trichlorosilane for 30 min or longer, the surface became superhydrophobic with an advancing water contact angle of greater than 160° and a water droplet (10 μL) roll-off angle of less than 5°. The order of nanoparticles dip coated onto the silicon wafer (i.e., 100 nm first and 20 nm second or vice versa) did not seem to have a significant effect on the resulting apparent water contact angle. In contrast, when the substrate was dip coated with monoscale nanoparticles (20, 50, and 100 nm), a highly hydrophobic surface (with an advancing water contact angle of up to 143°) was obtained, and the degree of hydrophobicity was found to be dependent on the particle size and concentration of the dip-coating solution. UV-vis spectra showed nearly 100% transmission in the visible region from the glass coated with dual-scale nanoparticles, similar to the bare one. The coating strategy was versatile, and superhydrophobicity was obtained on various substrates, including Si, glass, epoxy resin, and fabrics. Thermal annealing enhanced the stability of the nanoparticle coating, and superhydrophobicity was maintained against prolonged exposure to UV light under ambient conditions.