Response surface methodology in the development of a stacking-sensitive capillary electrophoresis method by field-amplified injection for the analysis of tricyclic antidepressants in the presence of salts

The work presented here explores the possibilities of the electrokinetic injection (EK) to achieve sensitive methods for the determination of tricyclic antidepressants in biological samples (serum). The addition of ACN to the sample, with high content in salts, causes stacking at the tip of the capillary, in a similar way as for hydrodynamic injection. An experimental design with the response surface methodology has been used to find the optimum composition of the matrix of the sample (sodium chloride and ACN percentages) and the conditions for the EK (water-plug length, time, and voltage of injection) in few experiments. The composition of the separation buffer was the same as utilized in a previous paper. The use of a bubble capillary to reach lower detection limits implies a loss of the resolution and requires a new optimization. Finally, a comparison between electrokinetic and hydrodynamic injections is made.     

On-line stacking techniques for the nonaqueous capillary electrophoretic determination of acrylamide in processed food

In the present study, field amplified sample stacking (FASS) techniques in the nonaqueous capillary electrophoresis method (NACE) were introduced for the on-line concentration of the acrylamide to improve acrylamide detection at 210 nm by diode-array detection. Acetonitrile (ACN) as a nonaqueous solvent permits acrylamide to be protonated through the change of its acid-base chemistry, allowing capillary electrophoretic separation of this compound. Choosing 30 mmol L(-1) HClO(4), 20 mmol L(-1) NaClO(4), 218 mmol L(-1) CH(3)COOH in ACN as the separation electrolyte and employing sample stacking methods, the LOD value of acrylamide was decreased to 2.6 ng mL(-1) with electrokinetic injection and 4.4 ng mL(-1) with hydrodynamic injection. Optimized stacking conditions were applied to the determination of acrylamide in several foodstuffs. The method is simple, rapid, inexpensive, and widely applicable for the determination of acrylamide in food samples.     

Analysis of tetracycline residues in bovine milk by CE-MS with field-amplified sample stacking

A rapid, sensitive, and robust CE-MS method has been developed for the determination of tetracycline, oxytetracycline, and chlortetracycline in milk. Field-amplified sample stacking with electromigration injection (FASS-EMI) was used for the online concentration of tetracyclines. The conditions of separation, MS detection, and stacking were systematically optimized. The optimum buffer composition was 35 mM Tris, 1.1% formic acid, 5% methanol, and 15% ACN. By using the online concentration method of field-enhanced sample stacking (FESI)-EMI stacking, the sensitivity was increased six- to seven-fold. The RSDs (n=6) of the relative migration time of tetracyclines were 1.1-1.4% for intraday and 2.4-2.9% for interday. The RSDs (n=6) of the relative peak area of tetracyclines were 3.2-4.6% for intraday and 4.7-6.1% for interday. The LODs (S/N=3) were 7.14 ng/mL for tetracycline, 11.4 ng/mL for oxytetracycline, and 14.9 ng/mL for chlortetracycline. The method has been successfully used to analyze tetracyclines residues in bovine milk.     

Separation and determination of four active anthraquinones in Chinese herbal preparations by flow injection-capillary electrophoresis

A simple, rapid, and accurate method for the separation and determination of physcion, chrysophanol, aloe-emodin, and emodin in Rhubarb, Juemingzi, and Chinese herbal preparations was developed by combination of flow injection-capillary zone electrophoresis for the first time. The analysis was carried out using an unmodified fused-silica capillary (75 mm x 50 microm ID x 375 microm OD, effective separation length of 48 mm) and direct ultraviolet detection at 254 nm. By a series of optimization, the sample solvent consisted of NaOH (100 mmol/L) and ACN (1:1 v/v), and a running buffer composed of 15 mmol/L sodium borate - 12.5 mmol/L sodium dihydrogen phosphate - 42% v/v ACN (pH 10.1) was applied for the separation of the four anthraquinones. The separation was rapid and highly reproducible, with complete resolution of all four compounds within 6 min. The sample throughput rate could reach up to 12 per h. The repeatability (defined as relative standard deviation) was 4.45, 4.44, 4.34, 0.61% with peak height evaluation and 1.62, 0.89, 2.49, 2.19% with peak area evaluation for physcion, chrysophanol, aloe-emodin, and emodin, respectively.     

Stacking and quantitative analysis of lovastatin in urine samples by the transient moving chemical reaction boundary method in capillary electrophoresis

A simple, sensitive, and useful concentration method for lovastatin (Lvt) in urine has been developed based on the transient moving chemical reaction boundary method (tMCRBM) in capillary electrophoresis. The MCRB is formed with acidic sample buffer (Gly-HCl) and alkaline running buffer (Gly-NaOH). The following optimal conditions were determined for stacking and separation: electrophoretic buffer of 100 mM Gly- NaOH (pH 11.52), sample buffer of 20 mM Gly-HCl (pH 4.93), fused-silica capillary of 76 cm × 75-μm i.d (67 cm from detector), sample injection at 14 mbar for 3 min. A 21- to 26-fold increase in peak height was achieved for detection of Lvt in urine under the optimal conditions compared with normal capillary zone electrophoresis. By combining the sample pretreatment procedure with the stacking method, the sensitivity of Lvt in urine was increased by 105- to 130-fold. The limits of detection (LOD) and quantification (LOQ) for Lvt in urine were decreased to 8.8 ng/mL and 29.2 ng/mL, respectively. The intra-day and inter-day precision values (expressed as RSD) were 2.23–3.61% and 4.03–5.05%, respectively. The recoveries of the analyte at three concentration levels changed from 82.65 to 100.49%.     

Determination of chlorophenoxy acid herbicides by capillary electrophoresis with integrated potential gradient detection

This report describes separation and detection of chlorophenoxy acid herbicides spiked in drinking water by the technique combining solid-phase extraction, field-amplified sample stacking, capillary electrophoresis, and potential gradient detection. The herbicide solution (400 mL) was concentrated to 0.1 mL by the solid-phase extraction procedure. The buffer containing 3 mM ammonia and 0.3 mM hydroxypropyl-beta-cyclodextrin was adjusted to pH 9.0 with ammonia. The sample solution was injected into the capillary to 30% of the whole length, and -9 kV and 9 kV were employed for field-amplified sample stacking and separation, respectively. The herbicides were baseline separated and the detection limits with the above combined techniques were in the range of 1-4 x 10(-2) ng/mL.     

Sample stacking for the analysis of eight penicillin antibiotics by micellar electrokinetic capillary chromatography

We studied the use of micellar electrokinetic capillary chromatography for separating eight penicillins. The method consists of (i) an electrophoretic separation based on micellar electrokinetic capillary chromatography, which uses sodium dodecyl sulfate (SDS) as surfactant; (ii) a sample stacking technique called reverse electrode polarity stacking mode (REPSM); and (iii) direct UV detection. The background electrolyte that gave complete separation contained 20 mM sodium borate buffer and 60 mM SDS. The sensitivity of the method was improved by an enrichment step that used on-column stacking. The limits of detection were at the microg.L(-1) level for the penicillins and did not detract from the peak resolution.     

On-line sample enrichment for the determination of proteins by capillary zone electrophoresis with poly(vinyl alcohol)-coated bubble cell capillaries

Field-amplified sample stacking (FASS) is used to separate basic proteins in a poly-(vinyl alcohol)-coated bubble cell capillary. To our knowledge, this is the first paper describing the on-column stacking of proteins (as cations) using FASS in bubble cell capillary. The bubble cell capillary is fabricated using a one-step method. Cetyltrimethylammonium chloride is added into the running buffer to reverse the EOF and, thus, to pump the water plug out during the sample stacking step. The effect of the water plug lengths and sample injection durations were investigated and optimized. The results obtained were compared with those for the normal capillary without bubble cell in terms of resolution and sensitivity enhancement. Under the optimal condition, this method can improve the sensitivity of the peak areas ranging from 5000- to 26 000-fold. The RSDs (n = 5) of the migration time and peak area are satisfactory (less than 0.6 and 12%, respectively). Application of the capillary electrophoresis method with bubble cell, FASS, and UV detection thereby leads to the determination of these proteins at concentrations ranging from 3 to 10 ng/mL, based on a signal-to-noise ratio of 3:1.     

Optimization of hydrophilic interaction LC by univariate and multivariate methods and its combination with salting‐out liquid–liquid extraction for the determination of antihypertensive drugs in the environmental waters

Hydrophilic interaction LC for the separation of four antihypertensive drugs was optimized by both univariate and multivariate methods. The column efficiency, resolution, and separation time were used as the three assessment parameters. The best separation condition of 97% ACN with 3% aqueous buffer containing 50 mM ammonium acetate at a pH of 3.0 was obtained by the two optimization methods. The multivariate optimization, orthogonal array design herein, was demonstrated to be a little tedious, but afforded a much better understanding of underlying separation factors. The content of ACN in the mobile phase contributed most significantly to separation. Furthermore, sample diluent and injection volume were found to influence the chromatographic performance. To match the hydrophilic interaction LC mobile phase, a proper sample pretreatment method, salting‐out liquid–liquid extraction, in which ACN was the extractant, was chosen. Since reserpine was unstable under both acidic and alkaline conditions, it was not studied in this part. The optimal salting‐out liquid–liquid extraction parameters were as follows: 400 μL ACN was added to 1 mL sample solution containing 500 mg NH₄Cl at a pH of 14.0. The linearity ranged from 0.01 to 1.00 μg/mL with r² > 0.9937. The LODs were between 1.9 and 2.5 ng/mL. The developed method was applied to the environmental water sample with good performance.     

Coupling of acetonitrile deproteinization and salting-out extraction with acetonitrile stacking for biological sample clean-up and the enrichment of hydrophobic compounds (porphyrins) in capillary electrophoresis

A new sample pretreatment approach in CE was developed for concurrent biological sample clean-up and the concentration of hydrophobic compounds based on the combination of ACN deproteinization with salting-out extraction. Further enhancement in concentration detection sensitivity was achieved by coupling (offline) salting-out extraction with an online CE sample enrichment technique known as "ACN stacking". By optimizing the pH of salting-out extraction, a number of model compounds (hydrophobic porphyrins with clinical significances), i.e. zinc-protoporphyrin, protoporphyrin, and coproporphyrin (CP) III and I, can be efficiently extracted from the aqueous sample into a smaller volume organic solvent (ACN) phase and an enrichment factor of ca. 100 can be obtained. The pressure injection of the enriched ACN phase (containing ca.1% NaCl) into the CE capillary at 10% capillary volume resulted in additional concentration of the various hydrophobic porphyrins, allowing for a combined enrichment factor of ca.1000 to be obtained. Calibration curves obtained for the determination of a pair of positional isomers with significant diagnostic value, urinary CPIII and CPI, were found to be linear between 10-300 ng/mL (with R2 = 0.999), and LODs (absorbance detection at 400 nm) were ca. 0.8 ng/mL (1.1 nmol/L of CPIII or CPI). Based on a single salting-out extraction, intraday precisions (nine consecutive injections) for both CPIII and CPI (at spiked concentrations of 10-300 ng/mL into urine) in terms of migration time and peak area were found to be within the range of 0.2-0.5 and 0.8-2.9%, respectively.     

Direct and sensitive analysis of methamphetamine, ketamine, morphine and codeine in human urine by cation-selective exhaustive injection and sweeping micellar electrokinetic chromatography

Cation-selective exhaustive injection and sweeping micellar electrokinetic chromatography (CSEI-Sweep-MEKC) was directly used to test some abuse drugs in human urine, including morphine (M), codeine (C), ketamine (K) and methamphetamine (MA). First, phosphate buffer (50 mM, pH 2.5) containing 30% methanol was filled into uncoated fused silica capillary (40 cm, 50 microm I.D.), then high conductivity buffer (100 mM phosphate, 6.9 kPa for 99.9 s) was followed. Electrokinetic injection (10 kV, 500 s) was used to load samples and to enhance sensitivity. The stacking step and separation were performed at -20 kV and 200 nm using phosphate buffer (25 mM, pH 2.5) containing 20% methanol and 100 mM sodium dodecyl sulfate. Using CSEI-Sweep-MEKC, the analytes could be simultaneously analyzed and have a detection limit down to ppb level. It was unnecessary to have sample pretreatments. During method validation, calibration plots were linear (r>or=0.9982) over a range of 150-3,000 ng/mL for M and C, 250-5,000 n g/mL for MA, and 50-1,000 ng/mL for K. The limits of detection were 15 ng/mL for M and C, and 5 ng/mL for MA and K (S/N=3, sampling 500 s at 10 kV). Comparing with capillary zone electrophoresis, the results indicated that this stacking method could increase 6,000-fold sensitivity for analysis of MA. Our method was applied for analysis of 28 real urine samples. The results showed good coincidence with immunoassay and GC-MS. This method was feasible for application to detect trace levels of abused drugs in forensic analysis.     

Cation-selective exhaustive injection and sweeping MEKC for direct analysis of methamphetamine and its metabolites in urine

Direct analysis of methamphetamine, amphetamine, and p-hydroxymethamphetamine in urine was achieved by cation-selective exhaustive injection and sweeping micellar EKC. A bare fused-silica capillary (40 cm, 50 microm id) was filled with phosphate buffer (80 mM, pH 3, containing 20% ACN). Then a high-conductivity buffer (100 mM phosphate, pH 3; 6.9 kPa for 2.5 min) was injected. Samples were loaded using electrokinetic injection (10 kV, 600 s) which created long zones of cationic analytes. To enhance sensitivity by sweeping, the stacking step was performed using a phosphate buffer (50 mM, pH 3, containing 20% ACN and 100 mM SDS) at -20 kV before separation by MEKC. This method was capable of detecting the analytes at ppb levels. The calibration plots were linear (r(2) >or= 0.9948) over a range of 100-5000 ng/mL for methamphetamine, and 100-2000 ng/mL for amphetamine and p-hydroxymethamphetamine. The LODs (S/N = 3) were 20 ng/mL for methamphetamine, and 15 ng/mL for amphetamine and p-hydroxymethamphetamine. The method was applied to analysis of 14 urine samples of addicts and is suitable for screening suspected samples for forensic purposes. The results showed good agreement with fluorescence polarization immunoassay and GC-MS.     

Analysis of anabolic androgenic steroids in urine by full-capillary sample injection combined with a sweeping CE stacking method

This study describes an on-line stacking CE approach by sweeping with whole capillary sample filling for analyzing five anabolic androgenic steroids in urine samples. The five anabolic steroids for detection were androstenedione, testosterone, epitestosterone, boldenone, and clostebol. Anabolic androgenic steroids are abused in sport doping because they can promote muscle growth. Therefore, a sensitive detection method is imperatively required for monitoring the urine samples of athletes. In this research, an interesting and reliable stacking capillary electrophoresis method was established for analysis of anabolic steroids in urine. After liquid–liquid extraction by n-hexane, the supernatant was dried and reconstituted with 30 mM phosphate buffer (pH 5.00) and loaded into the capillary by hydrodynamic injection (10 psi, 99.9 s). The stacking and separation were simultaneously accomplished at ?20 kV in phosphate buffer (30 mM, pH 5.0) containing 100 mM sodium dodecyl sulfate and 40 % methanol. During the method validation, calibration curves were linear (r?≥?0.990) over a range of 50–1,000 ng/mL for the five analytes. In the evaluation of precision and accuracy for this method, the absolute values of the RSD and the RE in the intra-day (n?=?3) and inter-day (n?=?5) analyses were all less than 6.6 %. The limit of detection for the five analytes was 30 ng/mL (S/N?=?5, sampling 99.9 s at 10 psi). Compared with simple MECK, this stacking method possessed a 108- to 175-fold increase in sensitivity. This simple and sensitive stacking method could be used as a powerful tool for monitoring the illegal use of doping.     

Trace analysis of zotepine and its active metabolite in plasma by capillary electrophoresis with solid phase extraction and head-column field-amplified sample stacking

A sensitive high-performance capillary zone electrophoresis (CZE) with head-column field-amplified sample stacking (FASS) in binary system has been developed for the simultaneous determination of zotepine and its active metabolite, norzotepine, in human plasma. The separation of zotepine and norzotepine was performed using a background electrolyte consisting of 50% ethylene glycol-borate buffer (20mM, pH 8.0) solution with 20% methanol as the running buffer and on-column detection at 200 nm. Under the optimal FASS-CZE condition, good separation with high efficiency and short analysis time is achieved. Several parameters affecting the separation and sensitivity of the drug were studied, including sample matrix, pH and concentrations of the borate buffer, ethylene glycol and methanol. Using clozapine as an internal standard, the linear ranges of the method for the determination of zotepine and norzotepine in human plasma were over 3-100 ng/mL; the detection limits of zotepine and norzotepine in plasma were 2 and 1 ng/mL, respectively. A sample pretreatment by means of solid-phase extraction (SPE) with subsequent quantitation by FASS-CZE was used. The application of the proposed method for determination of zotepine and norzotepine in plasma collected after oral administration of 125 mg zotepine in one schizophrenic patient was demonstrated.     

Capillary electrochromatography-mass spectrometry of cationic surfactants

The CEC-MS of alkyltrimethylammonium (ATMA+) ions with chain lengths ranging from C1-C18 is optimized using an internally tapered column packed with mixed mode reversed phase/strong cation exchange stationary phase. A systematic study of the CEC separation parameters is conducted followed by evaluation of the ESI-MS sheath liquid and spray chamber settings. First, the optimization of CEC separation parameters are performed including the ACN concentration, triethylamine (TEA) content, buffer pH and ammonium acetate concentration. Using 90% v/v ACN with 0.04% v/v TEA as mobile phase, the separation of longer chain C6-C18-TMA+ surfactants could be achieved in 15 min. Lowering the ACN concentration to 70% v/v provided resolution of shorter chain C1, C2-TMA+ from C6-TMA+ although the total analysis time increased to 40 min. Furthermore, variation of both the ACN and TEA content as well as ionic strength has found to significantly influence the retention of longer chain surfactants as compared to shorter chains. The optimum CEC conditions are 70% v/v ACN, 0.04% v/v TEA, pH 3.0 and 15 mM ammonium acetate. Next, the optimization of the ESI-MS sheath liquid composition is conducted comparing methanol to isopropanol followed by the use of experimental design for analysis of spray chamber parameters. Overall, the developed CEC-ESI-MS method allows quantitative and sensitive monitoring of ATMA+ from < or =10 microg/mL down to 10 ng/mL. Utilizing the optimized CEC-ESI-MS protocol, the challenging analysis of commercial sample Arquad S-50 ATMA+ containing cis-trans unsaturated and saturated soyabean fatty acid derivatives is demonstrated.     

Analysis of the disaccharides derived from hyaluronic acid and chondroitin sulfate by capillary electrophoresis with sample stacking

CE conditions for monitoring the unsaturated disaccharides of hyaluronic acid (di-HA) and chondroitin sulfate (di-CS) using an alkaline tetraborate buffer, electrokinetic sample injection, and UV absorption detection at 232 nm are reported. Separations were performed in an uncoated fused-silica capillary having reversed polarity and reversed electroosmosis generated with the addition of CTAB to the buffer. The influence of various separation parameters, including the concentration of CTAB, buffer pH, concentration of tetraborate, and applied voltage, on the resolution of the two disaccharides was investigated. Baseline separation was obtained with 25 mM tetraborate at pH 10.0 and having 0.05 mM CTAB. Chloride and phosphate in the sample are beneficial for the stacking of the disaccharides, with di-HA forming a much sharper peak than di-CS. Using samples prepared in 25 mM Tris-HCl (pH 7.5) and electrokinetic injection at the cathode at -10 kV for 40 s, linear relationships between the corrected peak area and the concentration of the disaccharides have been found in the ranges of 1.0-400.0 and 0.1-1.0 microg/mL (0.2-1.0 microg/mL for di-CS), with correlation coefficients being >0.9933 in all cases. The RSDs of detection times and corrected peak areas were between 1.13-1.24 and 1.57-2.13%, respectively. Applied to human serum samples that were prepared by ethanol precipitation and depolymerization of the two polysaccharides with chondroitinase ABC reveals comigration of endogenous compounds with di-HA and a sample-dependent detection time. The di-HA content in the serum sample can be estimated via subtraction of the blank peak that is obtained without enzymatic hydrolysis.     

Determination of Riboflavin in Cereal Grains by Capillary Electrophoresis with Laser-Induced Fluorescence Detection with On-Line Concentration

A very simple, sensitive, and reliable method for the routine determination of riboflavin in cereal grains by capillary electrophoresis with laser-induced fluorescence detection (CE-LIF) was established. Two on-line concentration techniques, namely, stacking in reverse migrating micelles (SRMM) and sweeping, were examined to enhance the detection signal. The optimum separation buffer consisted of 20 mM phosphoric acid and 140 mM sodium dodecyl sulfate (SDS), and a hydrodynamic injection of 30 s at 0.5 psi was confirmed for the introduction of a sample. In addition, it was found that salt in sample matrix influenced the performance of SRMM, showing the standard addition method was required for the quantitative analysis. The linearity of the method was good with a range of 0.5–500 ng/mL (r = 0.9990). The limit of detection (LOD) was 0.29 ng/mL at a signal-to-noise ratio of 3. This procedure presented was successfully applied to determine riboflavin in 18 samples of 9 types of cereal grains. The recovery rates varied from 94% to 98%, and the relative standard deviation (RSDs) was less than 4.1%.     

Nonaqueous capillary electrophoresis for rapid and sensitive determination of fangchinoline and tetrandrine in radix Stephaniae tetrandrae and its medicinal preparations

A simple, rapid, and sensitive non-aqueous capillary electrophoresis procedure with head-column field-amplified sample stacking concentration for the analysis of fangchinoline and tetrandrine is established. Optimum separation and stacking conditions were obtained when the sample was injected at 8 kV for 50 s after preliminary pressure injection of ethanol (16.9 kPa) for 0.6 s and separated with the buffer containing 50 mM ammonium acetate, 0.5% (v/v) acetic acid, and 50% (v/v) acetonitrile in methanol medium at 24 kV applied voltage. The analytes were detected by UV at 214 nm. The two bisbenzylisoquinoline alkaloids can be separated within 6 min and quantified with high sensitivity. The detection limits were 0.30 ng mL(-1) for fangchinoline and 0.34 ng mL(-1) for tetrandrine, which indicated that the sensitivities were at least 1000-fold enhanced over those reported in the literature as obtained by UV detection. The method was applied to the analysis of fangchinoline and tetrandrine in Radix Stephaniae tetrandrae and its medicinal preparations with good results.     

Sensitive analysis of donepezil in plasma by capillary electrophoresis combining on-column field-amplified sample stacking and its application in Alzheimer's disease

Field-amplified sample stacking (FASS) in capillary electrophoresis (CE) was used to determine the concentration of donepezil, an acetylcholinesterase inhibitor, in human plasma. A sample pretreatment by liquid-liquid extraction with isopropanol/n-hexane (v/v 3:97) and subsequent quantification by FASS-CE was used. Before sample loading, a water plug (0.5 psi, 6 s) was injected to permit FASS. Electrokinetic injection (7 kV, 90 s) was used to introduce sample cations. The separation condition for donepezil was performed in electrolyte solutions containing Tris buffer (60 mM, pH 4.0) with sodium octanesulfonate 40 mM and 0.01% polyvinyl alcohol as a dynamic coating to reduce analytes' interaction with capillary wall. The separation was performed at 28 kV and detected at 200 nm. Using atenolol as an internal standard, the linear ranges of the method for the determination of donepezil in human plasma were over a range of 1-50 ng/mL. The limit of detection was 0.1 ng/mL (S/N=3, sampling 90 s at 7 kV). One female volunteer (54 years old) was orally administered a single dose of 10 mg donepezil (Aricept, Eisai), and blood samples were drawn over a 60 h period for pharmacokinetic study. The method was also applied successfully to monitor donepezil in sixteen Alzheimer's disease patients' plasmas.     

毛细管电泳样品电堆积富集过程的数值研究

毛细管电泳样品电堆积富集过程可以浓缩样品组分,从而提高检测灵敏度,是一种有效的样品富集技术。本文通过合理的简化和假设,把毛细管中电堆积富集过程中所涉及的主要变量根据电势分布方程、缓冲溶液的浓度方程和样品粒子的质量传输方程进行耦合求解,建立了一个一维的数学模型,并应用有限元的方法对该模型进行了求解。计算结果给出了毛细管中缓冲溶液浓度及电场强度的分布随时间变化的过程,以及富集过程中毛细管中的电势分布曲线;得到了样品粒子浓度在电堆积富集过程和富集之后的再次扩散过程中的分布曲线以及正、负样品粒子的分离过程;最后分析了不同缓冲溶液浓度比对样品富集效果的影响。该研究为样品电堆积富集技术的进一步完善提供了一种简单可行的理论研究方法。