Effectiveness of the Photoactive Dye Methylene Blue versus Caspofungin on the Candida parapsilosis Biofilm in vitro and ex vivo

This research studied the effectiveness of the photoactive compound methylene blue (MB) activated with red LED light (576–672 nm) compared to that of caspofungin (CAS) on 1 Candida albicans and 3 Candida parapsilosis strains. Results were evaluated in terms of SMIC₅₀ for CAS or in PDI (photodynamic inactivation)‐SMIC₅₀ for MB (minimal inhibitory concentration inhibiting sessile biofilm to 50% in comparison to the control without CAS or after irradiation in comparison to the control without MB). While all strains were susceptible to CAS in planktonic form, the SMIC₅₀ was determined to be >16 μg mL^?1 when CAS was added to a 24 h biofilm. However, PDI‐MIC_50s (1.67 mW cm^?2, fluence 15 J cm^?2) were 0.0075–0.03 mmol L^?1. For biofilm, PDI‐SMIC_50s were in the range from 0.7 to 1.35 mmol L^?1. MB concentration of 1 mmol L^?1 prevented a biofilm being formed ex vivo on mouse tongues after irradiation regardless of the application time, in contrast to CAS, which was only effective at a concentration of 16 μg mL^?1 when it was added at the beginning of biofilm formation. PDI seems to be a promising method for the prevention of microbial biofilms that do not respond significantly to conventional drugs.     

Inside‐out Ultraviolet‐C Sterilization of Pseudomonas aeruginosa Biofilm In Vitro

Biofilms are difficult to eradicate due to a protective architecture and create major challenges in patient care by diminishing both host immune response and therapeutic approaches. This study investigated a new strategy for treating surface‐attached biofilms by delivering germicidal UV through a material surface in a process referred to as “inside‐out sterilization” (IOS). Mature Pseudomonas aeruginosa (ATCC^® 27853^?) biofilms were irradiated with up to 1400 mJ cm^?2 of germicidal UV from both ambient and IOS configurations. The lethal dose for the ambient exposure group was 461 mJ cm^?2 95% CI [292, 728] compared to the IOS treatment group of 247 mJ cm^?2 95% CI [187, 325], corresponding to 47% less UV dosage for the IOS group (P < 0.05). This study demonstrated that with IOS, a lower quantal dosage of UV energy is required to eradicate biofilm than with ambient exposure by leveraging the organizational structure of the biofilm.     

Solid‐contact Acetate‐selective Electrode Based on a 1,3‐bis(carbazolyl)urea‐ionophore

The construction and study of solid‐contact acetate‐selective electrodes is described using a 1,3‐bis(carbazolyl)urea derivative as a neutral hydrogen‐bonding ionophore and poly(3,4‐ethylenedioxythiophene) as the solid contact. It was shown recently that this ionophore binds acetate (logK_ass=4.98) that is used as primary ion in this study. The electrodes show linearity over the activity range of 10^?4.50–10^?1.10 with a sub‐Nernstian slope of ?51.3 mV per decade and a detection limit of 10^?5.00. The anion‐selectivity pattern of these electrodes deviates markedly from the Hofmeister pattern. When adding ionophore to the membrane the logarithm of the selectivity coefficient (logK) for SCN^? decreased from 6.5 to 1.2, logK for I^? decreased from 5.7 to 0.9, logK for NO₃^? decreased from 4.3 to 0.6 and logK for Br^? decreased from 3.3 to 0.1. The selectivity coefficients of hydrophilic anions such as Cl^?, F^?, HPO₄^2?, and SO₄^2? are significantly lower than in case of the ionophore‐free membrane. It was discovered that the constructed electrodes are also relatively selective to bicarbonate. This work is an important step towards the further development of solid‐contact anion‐selective electrodes.     

A Comparison of Dose Metrics to Predict Local Tumor Control for Photofrin‐mediated Photodynamic Therapy

This preclinical study examines light fluence, photodynamic therapy (PDT) dose and “apparent reacted singlet oxygen,” [¹O₂]_rx, to predict local control rate (LCR) for Photofrin‐mediated PDT of radiation‐induced fibrosarcoma (RIF) tumors. Mice bearing RIF tumors were treated with in‐air fluences (50–250 J cm^?2) and in‐air fluence rates (50–150 mW cm^?2) at Photofrin dosages of 5 and 15 mg kg^?1 and a drug‐light interval of 24 h using a 630‐nm, 1‐cm‐diameter collimated laser. A macroscopic model was used to calculate [¹O₂]_rx and PDT dose based on in vivo explicit dosimetry of the drug concentration, light fluence and tissue optical properties. PDT dose and [¹O₂]_rx were defined as a temporal integral of drug concentration and fluence rate, and singlet oxygen concentration consumed divided by the singlet oxygen lifetime, respectively. LCR was stratified for different dose metrics for 74 mice (66 + 8 control). Complete tumor control at 14 days was observed for [¹O₂]_rx ≥ 1.1 mm or PDT dose ≥1200 μm J cm^?2 but cannot be predicted with fluence alone. LCR increases with increasing [¹O₂]_rx and PDT dose but is not well correlated with fluence. Comparing dosimetric quantities, [¹O₂]_rx outperformed both PDT dose and fluence in predicting tumor response and correlating with LCR.     

Nanostructured Alpha‐Nickel Hydroxide Electrodes for High Performance Hydrogen Peroxide Sensing

Nanostructured alpha‐nickel hydroxide (α‐Ni(OH)₂) immobilized on a Fluorine‐doped Tin Oxide (FTO) surface was explored for the construction of hydrogen peroxide amperometric Flow Injection Analysis (FIA) sensors. Their notable electrocatalytic activity and heterogeneous electron‐transfer rate were confirmed by the appearance of a broad and intense peak associated with the oxidation of hydrogen peroxide and the enhancement of sensibility in hydrodynamic conditions. The α‐Ni(OH)₂ electrodes exhibited a broad dynamic range (5×10^?6 to 1×10^?3 mol L^?1), low detection limit (2×10^?7 mol L^?1), good repeatability (RSD=1.29 % for 20 successive analyses), and a sensitivity greater than 500 µA mmol^?1 L^?1 cm^?2.     

Sporicidal Effects of High‐Intensity 405 nm Visible Light on Endospore‐Forming Bacteria

Resistance of bacterial endospores to treatments, including biocides, heat and radiation is a persistent problem. This study investigates the susceptibility of Bacillus and Clostridium endospores to 405 nm visible light, wavelengths which have been shown to induce inactivation of vegetative bacterial cells. Suspensions of B. cereus endospores were exposed to high‐intensity 405 nm light generated from a light‐emitting diode array and results demonstrate the induction of a sporicidal effect. Up to a 4‐log₁₀ CFU mL^?1 reduction in spore population was achieved after exposure to a dose of 1.73 kJ cm^?2. Similar inactivation kinetics were demonstrated with B. subtilis, B. megaterium and C. difficile endospores. The doses required for inactivation of endospores were significantly higher than those required for inactivation of B. cereus and C. difficile vegetative cells, where ca 4‐log₁₀ CFU mL^?1 reductions were achieved after exposure to doses of 108 and 48 J cm^?2, respectively. The significant increase in dose required for inactivation of endospores compared with vegetative cells is unsurprising due to the notorious resilience of these microbial structures. However, the demonstration that visible light of 405 nm can induce a bactericidal effect against endospores is significant, and could have potential for incorporation into decontamination methods for the removal of bacterial contamination including endospores.     

Photodynamic Inactivation of Bacterial and Yeast Biofilms With a Cationic Porphyrin

The efficiency of 5,10,15,20‐tetrakis(1‐methylpyridinium‐4‐yl)porphyrin tetra‐iodide (Tetra‐Py⁺‐Me) in the photodynamic inactivation of single‐species biofilms of Staphylococcus aureus, Pseudomonas aeruginosa and Candida albicans and mixed biofilms of S. aureus and C. albicans was evaluated. The effect on the extracellular matrix of P. aeruginosa was also assessed. Irradiation with white light up to an energy dose of 64.8 J cm^?2 in the presence of 20 μm of Tetra‐Py⁺‐Me caused significant inactivation in all single‐species biofilms (3–6 log reductions), although the susceptibility was attenuated in relation to planktonic cells. In mixed biofilms, the inactivation of S. aureus was as efficient as in single‐species biofilms but the susceptibility of C. albicans decreased. In P. aeruginosa biofilms, a reduction of 81% in the polysaccharide content of the matrix was observed after treatment with a 20 μm PS concentration and a total light dose of 64.8 J cm^?2. The results show that the Tetra‐Py⁺‐Me causes significant inactivation of the microorganisms, either in biofilms or in the planktonic form, and demonstrate that polysaccharides of the biofilm matrix may be a primary target of photodynamic damage.     

Enhancement of the Efficacy of Photodynamic Inactivation of Candida albicans with the Use of Biogenic Gold Nanoparticles

This study reports on successful photodynamic inactivation of planktonic and biofilm cells of Candida albicans using Rose Bengal (RB) in combination with biogenic gold nanoparticles synthesized by the cell‐free filtrate of Penicillium funiculosum BL1 strain. Monodispersed colloidal gold nanoparticles coated with proteins were characterized by a number of techniques including SEM–EDS, TEM, UV–Vis absorption and fluorescence spectroscopy, as well as Fourier transform infrared spectroscopy to be 24 ± 3 nm spheres. A Xe lamp (output power of 20mW, delivering intensity of 53 mW cm^?2) was used as a light source to study the effects of RB alone, the gold nanoparticles alone and the RB‐gold nanoparticle mixture on the viability of C. albicans cells. The most effective reduction in the number of planktonic cells was found after 30 min of Xe lamp light irradiation (95.4 J cm^?2) and was 4.89 log₁₀ that is 99.99% kill for the mixture of RB with gold nanoparticles compared with 2.19 log₁₀ or 99.37% for RB alone. The biofilm cells were more resistant to photodynamic inactivation, and the highest effective reduction in the number of cells was found after 30 min of irradiation in the presence of the RB–gold nanoparticles mixture and was 1.53 log₁₀, that is 97.04% kill compared with 0.6 log₁₀ or 74.73% for RB. The probable mechanism of enhancement of RB‐mediated photodynamic fungicidal efficacy against C. albicans in the presence of biogenic gold nanoparticles is discussed leading to the conclusion that this process may have a multifaceted character.     

Polymer electrolyte membranes by in situ polymerization of poly(ethylene carbonate‐co‐ethylene oxide) macromonomers in blends with poly(vinylidene fluoride‐co‐hexafluoropropylene)

Salt‐containing membranes based on polymethacrylates having poly(ethylene carbonate‐co‐ethylene oxide) side chains, as well as their blends with poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVDF‐HFP), have been studied. Self‐supportive ion conductive membranes were prepared by casting films of methacrylate functional poly(ethylene carbonate‐co‐ethylene oxide) macromonomers containing lithium bis(trifluorosulfonyl)imide (LiTFSI) salt, followed by irradiation with UV‐light to polymerize the methacrylate units in situ. Homogenous electrolyte membranes based on the polymerized macromonomers showed a conductivity of 6.3 × 10^?6 S cm^?1 at 20 °C. The preparation of polymer blends, by the addition of PVDF‐HFP to the electrolytes, was found to greatly improve the mechanical properties. However, the addition led to an increase of the glass transition temperature (T_g) of the ion conductive phase by ～5 °C. The conductivity of the blend membranes was thus lower in relation to the corresponding homogeneous polymer electrolytes, and 2.5 × 10^?6 S cm^?1 was recorded for a membrane containing 10 wt % PVDF‐HFP at 20 °C. Increasing the salt concentration in the blend membranes was found to increase the T_g of the ion conductive component and decrease the propensity for the crystallization of the PVDF‐HFP component. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 79–90, 2007     

Reduced Graphene Oxide|Carbon Ceramic Electrode Modified with CdS‐Hemoglobin as a Sensitive Hydrogen Peroxide Biosensor

A sensitive hydrogen peroxide (H₂O₂) biosensor was developed based on a reduced graphene oxide|carbon ceramic electrode (RGO|CCE) modified with cadmium sulfide‐hemoglobin (CdS‐Hb). The electron transfer kinetics of Hb were promoted due to the synergetic function of RGO and CdS nanoparticles. The transfer coefficient (α) and the heterogeneous electron transfer rate constant (k_s) were calculated to be 0.54 and 2.6 s^?1, respectively, indicating a great facilitation achieved in the electron transfer between Hb and the electrode surface. The biosensor showed a good linear response to the reduction of H₂O₂ over the concentration range of 2–240 µM with a detection limit of 0.24 µM (S/N=3) and a sensitivity of 1.056 µA µM^?1 cm^?2. The high surface coverage of the CdS‐Hb modified RGO|CCE (1.04×10^?8 mol cm^?2) and a smaller value of the apparent Michaelis? Menten constant (0.24 mM) confirmed excellent loading of Hb and high affinity of the biosensor for hydrogen peroxide.     

Nonenzymatic Hydrogen Peroxide Electrochemical Sensor Based on Au‐HS/SO3H‐PMO (Et) Nanocomposite

A newly nonenzymatic sensor for hydrogen peroxide (H₂O₂) based on the (Au‐HS/SO₃H‐PMO (Et)) nanocomposite is demonstrated. The electrochemical properties of the as‐prepared nanocomposite were studied. It displayed an excellent performance towards H₂O₂ sensing in the linear response range from 0.20 µM to 4.30 mM (R=0.9999) with a sensitivity of 6.35×10² µA µM^?1 cm^?2 and a low detection limit of 0.0499 µM. Furthermore, it was not affected by electroactive interference species. These features proved that the modified electrode was suitable for determination of H₂O₂.     

Synthesis of Tri‐functional Core‐shell CuO@carbon Quantum Dots@carbon Hollow Nanospheres Heterostructure for Non‐enzymatic H2O2 Sensing and Overall Water Splitting Applications

A core‐shell structure with CuO core and carbon quantum dots (CQDs) and carbon hollow nanospheres (CHNS) shell was prepared through facile in‐situ hydrothermal process. The composite was used for non‐enzymatic hydrogen peroxide sensing and electrochemical overall water splitting. The core‐shell structure was established from the transmission electron microscopy image analysis. Raman and UV‐Vis spectroscopy analysis confirmed the interaction between CuO and CQDs. The electrochemical studies showed the limit of detection and sensitivity of the prepared composite as 2.4 nM and 56.72 μA μM^?1 cm^?2, respectively. The core‐shell structure facilitated better charge transportation which in turn exhibited elevated electro‐catalysis towards hydrogen evolution reaction (HER), oxygen evolution reaction (OER) and overall water splitting. The overpotential of 159 mV was required to achieve 10 mA cm^?2 current density for HER and an overpotential of 322 mV was required to achieve 10 mA cm^?2 current density for OER in 1.0 M KOH. A two‐electrode system was constructed for overall water splitting reaction, which showed 10 and 50 mA cm^?2 current density at 1.83 and 1.96 V, respectively. The prepared CuO@CQDs@CHNS catalyst demonstrated excellent robustness in HER and OER catalyzing condition along with overall water splitting reaction. Therefore, the CuO@CQDs@CHNS could be considered as promising electro‐catalyst for H₂O₂ sensing, HER, OER and overall water splitting.     

Amperometric Biosensor for Hydrogen Peroxide Based on Electrodeposited Sub-micrometer Gold Modified Glassy Carbon Electrode

IntroductionAmperometricbiosensorofhydrogenperoxideisofpracticalimportancebecauseofitswideapplicationsinchemical,biological,clinical,environmentalandmanyotherfields.Forimprovementofsensor抯quality,vari-ouskindsofchemicalmodificationmethodshavebeendevelopedforreducingredoxoverpotentialsofH2O2atelectrodesurfaces,increasingthedetectionsensitivity,linearrange,stabilityandlivetime.Ithasbeenshownthattheuseofsub-micrometersizedmetalparticlessuchasPt-blackcansignificantlyimprovethequalityofthebiosens…     

Synthesis and characterization of low‐bandgap cyclopentadithiophene‐biselenophene copolymer and its use in field‐effect transistor and polymer solar cells

Novel series of conjugated copolymers, incorporating cyclopentadithiophene (CPDT) and the biselenophene ( R‐CPDT‐Se2 ), were synthesized by Pd‐catalyzed Stille coupling polymerization. The optical, electrochemical, field‐effect carrier mobilities, and photovoltaic properties of the R‐CPDT‐Se2 were investigated and compared with cyclopentadithiophene (CPDT) and the bithiophene ( EHex‐CPDT‐T2 ). The highest hole mobility of thin film transistor devices fabricated with new p‐type polymer semiconductors, Oct‐CPDT‐Se2 , was 1.3 × 10^?3 cm²/Vs with an on/off ratio of about 10⁵. The maximum power conversion efficiency of polymer solar cell fabricated with the blend of EHex‐CPDT‐Se2 /C₇₁‐PCBM reached 1.86% with an open circuit voltage (V_OC) of 0.55 V, a short circuit current density (J_sc) of 7.27 mA/cm², and a fill factor (FF) of 0.47 under AM 1.5G irradiation (100 mW/cm²). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2009     

Thermodynamics of Carbon Dioxide Adsorption on the Protonic Zeolite H‐ZSM‐5

Adsorption of carbon dioxide on H‐ZSM‐5 zeolite (Si:Al=11.5:1) was studied by means of variable‐temperature FT‐IR spectroscopy, in the temperature range of 310–365 K. The adsorbed CO₂ molecules interact with the zeolite Brønsted‐acid OH groups bringing about a characteristic red‐shift of the O? H stretching band from 3610 cm^?1 to 3480 cm^?1. Simultaneously, the ν₃ mode of adsorbed CO₂ is observed at 2345 cm^?1. From the variation of integrated intensity of the IR absorption bands at both 3610 and 2345 cm^?1, upon changing temperature (and CO₂ equilibrium pressure), the standard adsorption enthalpy of CO₂ on H‐ZSM‐5 is ΔH⁰=?31.2(±1) kJ mol^?1 and the corresponding entropy change is ΔS⁰=?140(±10) J mol^?1 K^?1. These results are discussed in the context of available data for carbon dioxide adsorption on other protonic, and also alkali‐metal exchanged, zeolites.     

SnFe2O4 Nanocrystals as Highly Efficient Catalysts for Hydrogen‐Peroxide Sensing

SnFe₂O₄ nanocrystals (NC), prepared with a simple one‐step carrier‐solvent‐assisted interfacial reaction process, were developed as highly efficient catalysts for hydrogen peroxide sensing. These NCs, with a size of around 7 nm, served as the sensing catalyst and were decorated onto the pore surfaces of a porous fluorine‐doped tin oxide (PFTO) host electrode, prepared from commercial FTO glass with a simple anodic treatment, to form the sensing electrode for hydrogen peroxide. The SnFe₂O₄ NCs‐loaded PFTO electrode exhibited an ultra‐high sensitivity of 1027 mA m ^?1 cm^?2 toward hydrogen peroxide, outperforming Pt NCs‐loaded PFTO electrodes. The SnFe₂O₄ NCs‐loaded PFTO electrode proved a promising relatively low cost, high performance sensing electrode for hydrogen peroxide.     

Photodynamic Inactivation of Planktonic Cultures and Biofilms of Candida albicans Mediated by Aluminum‐Chloride‐Phthalocyanine Entrapped in Nanoemulsions

New drug delivery systems, such as nanoemulsions (NE), have been developed to allow the use of hydrophobic drugs on the antimicrobial photodynamic therapy. This study evaluated the photodynamic potential of aluminum‐chloride‐phthalocyanine (ClAlPc) entrapped in cationic and anionic NE to inactivate Candida albicans planktonic cultures and biofilm compared with free ClAlPc. Fungal suspensions were treated with different delivery systems containing ClAlPc and light emitting diode. For planktonic suspensions, colonies were counted and cell metabolism was evaluated by XTT assay. Flow cytometry evaluated cell membrane damage. For biofilms, the metabolic activity was evaluated by XTT and ClAlPc distribution through biofilms was analyzed by confocal laser scanning microscopy (CLSM). Fungal viability was dependent on the delivery system, superficial charge and light dose. Free ClAlPc caused photokilling of the yeast when combined with 100 J cm^?2. Cationic NE‐ClAlPc reduced significantly both colony counts and cell metabolism (P < 0.05). In addition, cationic NE‐ClAlPc and free ClAlPc caused significant damage to the cell membrane (P < 0.05). For the biofilms, cationic NE‐ClAlPc reduced cell metabolism by 70%. Anionic NE‐ClAlPc did not present antifungal activity. CLSM showed different accumulation on biofilms between the delivery systems. Although NE system showed a lower activity for planktonic culture, cationic NE‐ClAlPc showed better results for Candida biofilms.     

Elucidation of the Intersystem Crossing Mechanism in a Helical BODIPY for Low‐Dose Photodynamic Therapy

Intersystem crossing (ISC) of triplet photosensitizers is a vital process for fundamental photochemistry and photodynamic therapy (PDT). Herein, we report the co‐existence of efficient ISC and long triplet excited lifetime in a heavy atom‐free bodipy helicene molecule. Via theoretical computation and time‐resolved EPR spectroscopy, we confirmed that the ISC of the bodipy results from its twisted molecular structure and reduced symmetry. The twisted bodipy shows intense long wavelength absorption (?=1.76×10⁵ m ^?1 cm^?1 at 630 nm), satisfactory triplet quantum yield (Φ_T=52 %), and long‐lived triplet state (τ_T=492 μs), leading to unprecedented performance as a triplet photosensitizer for PDT. Moreover, nanoparticles constructed with such helical bodipy show efficient PDT‐mediated antitumor immunity amplification with an ultra‐low dose (0.25 μg kg^?1), which is several hundred times lower than that of the existing PDT reagents.     

CH⋅⋅⋅N Hydrogen‐Bonding Interaction in 7‐Azaindole:CHX3 (X=F,Cl) Complexes

The C?H???Y (Y=hydrogen‐bond acceptor) interactions are somewhat unconventional in the context of hydrogen‐bonding interactions. Typical C?H stretching frequency shifts in the hydrogen‐bond donor C?H group are not only small, that is, of the order of a few tens of cm^?1, but also bidirectional, that is, they can be red or blue shifted depending on the hydrogen‐bond acceptor. In this work we examine the C?H???N interaction in complexes of 7‐azaindole with CHCl₃ and CHF₃ that are prepared in the gas phase through supersonic jet expansion using the fluorescence depletion by infra‐red (FDIR) method. Although the hydrogen‐bond acceptor, 7‐azaindole, has multiple sites of interaction, it is found that the C?H???N hydrogen‐bonding interaction prevails over the others. The electronic excitation spectra suggest that both complexes are more stabilized in the S₁ state than in the S₀ state. The C?H stretching frequency is found to be red shifted by 82 cm^?1 in the CHCl₃ complex, which is the largest redshift reported so far in gas‐phase investigations of 1:1 haloform complexes with various substrates. In the CHF₃ complex the observed C?H frequency is blue shifted by 4 cm^?1. This is at variance with the frequency shifts that are predicted using several computational methods; these predict at best a redshift of 8.5 cm^?1. This discrepancy is analogous to that reported for the pyridine‐CHF₃ complex [W. A. Herrebout, S. M. Melikova, S. N. Delanoye, K. S. Rutkowski, D. N. Shchepkin, B. J. van der Veken, J. Phys. Chem. A­ 2005 , 109, 3038], in which the blueshift is termed a pseudo blueshift and is shown to be due to the shifting of levels caused by Fermi resonance between the overtones of the C?H bending and stretching modes. The dissociation energies, (D₀), of the CHCl₃ and CHF₃ complexes are computed (MP2/aug‐cc‐pVDZ level) as 6.46 and 5.06 kcal mol^?1, respectively.     

CoP‐Doped MOF‐Based Electrocatalyst for pH‐Universal Hydrogen Evolution Reaction

Although electrocatalysts based on transition metal phosphides (TMPs) with cationic/anionic doping have been widely studied for hydrogen evolution reaction (HER), the origin of performance enhancement still remains elusive mainly due to the random dispersion of dopants. Herein, we report a controllable partial phosphorization strategy to generate CoP species within the Co‐based metal‐organic framework (Co‐MOF). Density functional theory calculations and experimental results reveal that the electron transfer from CoP to Co‐MOF through N‐P/N‐Co bonds could lead to the optimized adsorption energy of H₂O (ΔG ) and hydrogen (ΔG_H*), which, together with the unique porous structure of Co‐MOF, contributes to the remarkable HER performance with an overpotential of 49 mV at a current density of 10 mA cm^?2 in 1 m phosphate buffer solution (PBS, pH 7.0). The excellent catalytic performance exceeds almost all the documented TMP‐based and non‐noble‐metal‐based electrocatalysts. In addition, the CoP/Co‐MOF hybrid also displays Pt‐like performance in 0.5 m H₂SO₄ and 1 m KOH, with the overpotentials of 27 and 34 mV, respectively, at a current density of 10 mA cm^?2.