温度敏感聚(N-异丙基丙烯酰胺-co-甲基丙烯酰氧乙基二甲基辛基溴化铵)水凝胶的溶胀性能研究

由于改变亲水／疏水单体比值、与离子单体共聚心、改变凝胶内部结构等均可不同程度地调整温敏水凝胶的溶胀性能,本研究选择一种既含疏水烷基又含季铵盐正离子型亲水基团的两亲性单体——甲基丙烯酰氧乙基二甲基辛基溴化铵（ADMOAB）,结构如示意图1所示．与N-异丙基丙烯酰胺（NIPAM）聚合,制备了P（NIPAM-co-ADMOAB）共聚水凝胶,以便在引入离子型结构单元的同时,改变凝胶体系中亲水／疏水单体比值,避免单纯增加疏水单体引起的水凝胶溶胀性降低问题,并考察了ADMOAB对水凝胶溶胀性能的影响,对该类水凝胶迄今鲜见相关文献报道．该研究对进一步了解水凝胶的构效关系、探索有效控制溶胀性能的途径具有积极意义．     

溶剂改性疏水pH-敏感凝胶的溶胀行为

在甲苯存在下，以甲基丙烯酸二乙氨基乙酯、苯乙烯和二乙烯苯为单体，通过悬浮聚合方法合成了不同交联度的疏水阳离子凝胶，研究了这些凝胶的pH－敏感溶胀行为。发现以良溶剂甲苯改性的凝胶不仅溶胀度增加，而且溶胀性质对交联度改变出现特异的依赖关系。当凝胶的交联度高于20％时，平衡溶胀度和溶胀速度随交联度的提高不是降低，而是提高。同时发现，随交联度提高，改性凝胶的溶胀逐渐具有零级动力学特性。这对设计由溶胀控制的，具有零级动力学释药特性的控释体系是十分有意义的。     

含金刚烷基的N-异丙基丙烯酰胺共聚物水凝胶的制备和性能研究

合成了含金刚烷基的甲基丙烯酸金刚烷酯(AdMA)疏水单体,并通过与N-异丙基丙烯酰胺(NIPAM)共聚,制备了温敏性的(P(NIPAM-co-AdMA))共聚物水凝胶.用傅里叶变换红外光谱仪(FTIR)表征了凝胶的化学结构,用环境扫描电镜(ESEM)对凝胶断层结构的形貌进行了观察,用DSC测试了凝胶的体积相转变温度(LCST),并研究了共聚水凝胶的溶胀性能.结果表明,共聚物水凝胶的LCST能够高效地通过改变疏水单体的含量来调节,在实验所考察的范围内,LCST随AdMA含量的增加而线性降低;疏水单体的含量对凝胶的孔洞结构和溶胀性能存在一最优值,在最优的单体配比下,水凝胶具有均匀规整的大孔结构和超快的响应速率.如疏水单体含量为3%(AdMA∶NIPAM=3%)的共聚物水凝胶具有如渔网般均匀的多孔结构,当发生去溶胀时,在5min内就可以失去92%的水,不到10min的时间就可以完全达到去溶胀平衡,水保留率在4%以下.     

基于光聚合星型PEG-b-PCL大分子单体可生物降解水凝胶的合成及表征

以辛酸亚锡为催化剂 ,通过星型聚乙二醇 (PEG)引发ε 己内酯 (CL)开环聚合 ,制备了PEG b PCL嵌段共聚物 ,进一步以丙烯酸酯封端 ,合成了 3种水溶性大分子单体 .以 2 ,2 二甲氧基 2 苯基苯乙酮为引发剂 ,在紫外光作用下 ,大分子单体在水中由于胶束的形成能够迅速聚合形成水凝胶 .利用1 H NMR、FTIR、DSC、TGA、ESEM、凝胶含量、溶胀比等分析测试手段对大分子单体及其形成的水凝胶进行了表征 .结果表明 ,干胶迅速吸水而达到溶胀平衡 ,水凝胶具有较大的溶胀比和高的水含量 ;随着PEG臂数的增加 ,干胶的熔融峰顶温度下降 ,凝胶的溶胀比减小 ;ESEM图片上清晰地表明水凝胶的网络结构     

IPAAm凝胶在丙酮水溶液中溶胀行为的关联与预报

基于Maurer和Prausnitz的凝胶相平衡条件，建立了凝胶的溶胀模型.模型假设凝胶是以凝胶组分及凝胶吸收的溶液为核心，以弹性半渗透膜为壳的复合体.并采用UNIQUAC方程计算凝胶相及与之共存液相的Gibbs过剩自由能，采用“phantomnetwork”理论计算凝胶的弹性自由能，采用“自由体积”计算分子的尺度效应.同时以N-异丙基丙烯酰胺（IPAAm）为单体合成了IPAAm凝胶.研究了25 ℃时IPAAm凝胶在丙酮水溶液中的溶胀行为，并测定了丙酮在胶体相和与之共存液相中的分配，以检验模型的关联与预报能力.结果表明,模型预报的单体总量和交联剂浓度对凝胶溶胀的影响与实验符合得很好.而且凝胶溶胀时，能很好地预测丙酮在两相中的分配,表明模型具有很好的关联和预报能力.     

甲基丙烯酸烷基酯为疏水成分的溶剂改性pH-敏感凝胶的溶胀行为

以不同酯烷基链长的甲基丙烯酸烷基酯为疏水成分，甲基丙烯酸二乙氨基乙酯(DEA)为可离子化单体，及以二甲基丙烯酸乙二醇酯(EGDM)或二乙烯苯(DVB)为交联剂，合成了数个系列甲苯改性的不同交联度的疏水阳离子凝胶，研究了这些凝胶以pH-敏感溶胀为主的容胀行为．发现以甲基丙烯酸正丁酶(BMA)，EGDM及DEA合成的改性凝胶，与以苯乙烯(St)，DVB及DEA合成的溶剂改性凝胶具有十分相似的平衡溶胀和动力学溶胀性质．研究结果为增加疏水阳离子凝胶的载药种类，拓宽由pH改变而触发释药的控释体系的应用范围提供了新的途径．     

温度/pH敏感性接枝共聚物水凝胶P(DMAEMA-g-NIPAM)的 合成及性质研究

利用大分子单体技术, 采用自由基溶液聚合合成了温度/pH敏感性聚甲基丙烯酸-N,N-二甲氨基乙酯接枝聚N-异丙基丙烯酰胺[P(DMAEMA-g-NIPAM)]水凝胶. 用红外光谱及扫描电镜对凝胶的组成及形貌进行了表征. 凝胶的去溶胀和溶胀动力学研究表明, 所合成的凝胶具有温度和pH敏感性. 与传统的聚丙烯酸系水凝胶相比, P(DMAEMA-g- NIPAM)具有相反的pH敏感性; P(DMAEMA-g-NIPAM)凝胶在55 ℃时具有较快的去溶胀速率, 随着凝胶中接枝链PNIPAM量的增加, 凝胶的去溶胀速率加快.     

N-异丙基丙烯酰胺-丙烯酰胺热敏凝胶的溶胀特性

制备并表征了N-异丙基丙烯酰胺-丙烯酰胺热敏凝胶(NIPAm-Am),研究了单体配比、引发剂、交联剂用量和温度对其溶胀特性的影响。结果表明：NIPAm-Am热敏凝胶是由亲水和疏水基团组成的非晶高聚物。mAm／mNIPAm越大,凝胶的平衡溶胀率越大;增加交联剂的用量,凝胶的溶胀率减小,当引发剂的质量分数为0．008时溶胀率达最大值;温度的增加会使凝胶的溶胀率减小,在相转变温度时,溶胀率的变化最大。     

阳离子型温敏水凝胶的溶胀性能及其对表面活性剂的吸附行为

阳离子单体;温敏凝胶;阳离子型温敏水凝胶的溶胀性能及其对表面活性剂的吸附行为     

侧链含不同功能性羟基的温敏性N-异丙基丙烯酰胺共聚物微凝胶的制备及性能比较

选择含有活性羟基的亲水单体多缩乙二醇单甲基丙烯酸酯(PEGMA)、甲基丙烯酸羟乙酯(HEMA),分别和N-异丙基丙烯酰胺(NIPAM)交联共聚,制备了侧链含有功能性羟基、链长不同的温敏性微凝胶.研究发现,亲水单体HEMA和PEGMA的引入对微凝胶的去溶胀性能有不同的影响,PEGMA的引入使得微凝胶的体积相转变温度升高,微凝胶的去溶胀比随着PEGMA投料比的增加而降低.而HEMA的引入使得微凝胶的体积相转变温度降低;微凝胶的去溶胀比随着HEMA投料比的增加先是增加然后降低,当HEMA的投料比为8mol%时,去溶胀比达到最大.     

N-异丙基甲基丙烯酰胺共聚热缩温敏水凝胶

从甲基丙烯腈与异丙醇反应制备了N-异丙基甲基丙烯酰胺(NIPM),研究了其以N,N′-亚甲基双丙烯酰胺(MBA)为交联剂在不同溶剂体系的聚合及所形成的水凝胶的性质。表明NIPM-MBA凝胶具有热缩温敏性。在NIPM-MBA体系引入丙烯酸钠、甲基丙烯酸钠等负离子单体时,凝胶的溶胀比明显增加,MBA所占比例较少的体系,具有热缩、热胀双重性。     

新型阴离子型温敏水凝胶

新型阴离子型温敏水凝胶王昌华,曹维孝（北京大学化学与分子工程学院,北京,１００８７１）关键词温敏水凝胶,溶胀比,Ｎ－异丙基丙烯酰胺１９８４年Ｔａｎａｋａ等人［１］发现Ｎ－异丙基丙烯酰胺（ＮＩＰＡ）与Ｎ,Ｎ－亚甲基双丙烯酰胺（ＭＢＡ）的微交联共聚体,在...     

载万古霉素PLGA-PEG-PLGA温度敏感水凝胶的体外抗菌性能

利用聚乙二醇（PEG 1500）引发乙交酯和D,L-丙交酯开环共聚合制备聚丙交酯乙交酯（PLGA）三嵌段共聚物（PLGA-PEG-PLGA）温敏水凝胶材料,并通过核磁共振氢谱（¹H NMR）确定产物的结构及组成.应用倒置小瓶法测量得到不同浓度下PLGA-PEG-PLGA水凝胶的溶胶-凝胶相变温度为27~32℃.此外,体外降解实验及细胞毒性实验结果表明,质量分数为25%的水凝胶有满意的降解速度及良好的生物相容性.同时,利用紫外-可见光谱分析了载万古霉素水凝胶的体外药物释放行为,结果表明,万古霉素可以持续释放12 d.抗菌实验结果表明,载万古霉素水凝胶具有良好的抗菌效果.表明PLGA-PEG-PLGA三嵌段温敏水凝胶是一种较理想的万古霉素缓释载体,具有良好的临床应用前景.     

Rheological studies of thermosensitive triblock copolymer hydrogels

Hydrogel formation by physical cross-linking is a developing area of research toward materials suitable for pharmaceutical and biomedical applications. Polymers exhibiting lower critical solution temperature (LCST) behavior in aqueous solution are used in this study to prepare hydrogels. Four triblock copolymers (ABA) with thermosensitive poly(N-(2-hydroxypropyl) methacrylamide lactate) A-blocks and a hydrophilic poly(ethylene glycol) B-block have been synthesized. The molecular weight of the hydrophilic PEG block was fixed at 10 kDa, whereas the molecular weight of the pHPMAm-lactate block was varied between 10 and 20 kDa. The rheological characteristics of these polymer hydrogels were studied as a function of temperature, concentration, and the length of the thermosensitive blocks. Gelation occurred rapidly upon increasing the temperature to 37 degrees C, which makes this system suitable as an injectable formulation. The gels became stronger with increasing temperature and concentration, and moreover they behaved as critical gels, which means that G' and G' ' follow power laws over the entire frequency range. Surprisingly, with increasing length of the thermosensitive blocks, weaker hydrogels were formed. This trend can be explained by the cross-link density of the physical network, which increases with decreasing length of the thermosensitive blocks.     

Immobilization of insulin-like growth factor-1 onto thermosensitive hydrogels to enhance cardiac progenitor cell survival and differentiation under ischemic conditions

Stem cell therapy is a promising approach to treat myocardial infarction. However, direct delivery of stem cells into hearts experiences poor cell engraftment and differentiation, due to ischemic conditions (low nutrient and oxygen) in the infarct hearts. Development of suitable cell carriers capable of supporting cell survival and differentiation under these harsh conditions is critical for improving the efficacy of current stem cell therapy. In this work, we created a family of novel cell carriers based on thermosensitive hydrogels and insulin-like growth factor 1 (IGF-1), and investigated if these cell carriers can improve cell survival and differentiation under ischemic conditions. The thermosensitive hydrogels were synthesized from N-isopropylacrylamide, acrylic acid, acrylic acid N-hydroxysuccinicimide ester, and 2-hydroxyethyl methacrylate-oligo(hydroxybutyrate). The hydrogel solutions can be readily injected through 26G needles, and can quickly solidify at 37 °C to form highly flexible hydrogels. IGF-1 was immobilized into the hydrogels in order to support long-term cell survival and differentiation. Different amount of IGF-1 was immobilized by using hydrogels with different content of N-hydroxysuccinicimide ester groups. Cardiosphere derived cells were encapsulated in the hydrogels and cultured under ischemic conditions. The results demonstrated that a significant improvement of cell survival and differentiation was achieved after IGF-1 immobilization. These IGF-1 immobilized hydrogels have the potential to improve cell survival and differentiation in infarct hearts.     

快速响应温敏水凝胶研究进展

温敏水凝胶是一类具有广泛应用前景的高分子材料,但是由于传统方法合成的水凝胶响应速率较慢因而限制了其应用,因此近年来围绕提高传统水凝胶的响应速率做了大量研究工作。本文从几个方面综述了近年来快速响应的温敏水凝胶的研究进展,并对有关现象进行了解释和说明。     

快速响应的温敏性聚(N-异丙基丙烯酰胺)水凝胶 Ⅰ.以CaCO_3为成孔剂制备方法、表征及动力学研究

以不同粒径的CaCO3粒子为成孔剂 ,合成了快速响应的温敏性聚 (N 异丙基丙烯酰胺 ) (PNIPA)水凝胶 .利用扫描电镜观察到水凝胶具有特殊的孔状结构 ,得到水凝胶的孔径大小为几十微米左右 .动力学研究表明 ,该水凝胶在温敏膨胀或收缩时 ,具有快速的响应速率 ,在 10min内的失水率可达 90 % .比较了干凝胶和4 0℃下失水后的凝胶两种不同状态下水凝胶的膨胀曲线 ,发现两者的溶胀动力学曲线明显不同 ,前者的曲线有拐点 .同时发现与失水收缩速率相比 ,水凝胶具有较慢的吸水膨胀速率 .     

Effect of Sodium Alginate on the Properties of Thermosensitive Hydrogels

Sodium alginate (SA ) was combined with poly(N ‐isopropylacrylamide) (PNIPAAm ) to prepare thermosensitive hydrogels through semi‐interpenetrating polymer network (semi‐IPN ) and fully interpenetrating polymer network (full‐IPN ). The thermosensitive, swelling, mechanical, and thermal properties of pure PNIPAAm , SA /PNIPAAm semi‐IPN , and Ca‐alginate/PNIPAAm full‐IPN hydrogels were investigated. The formation of semi‐IPN and full‐IPN significantly improved the hydrogels’ swelling capability and mechanical properties without altering their thermosensitivity. 5‐Fluorouracil (5‐Fu) was selected as a model drug to study the release behaviors of the hydrogels. It was found that in vitro controlled drug release from semi‐IPN hydrogels showed an initial release burst, followed by a slower and sustained release, before reaching equilibrium. Full‐IPN hydrogels showed slow and sustained release during the whole process. Temperature and pH were found to affect the rate of drug release. Ca‐alginate/PNIPAAm full‐IPN hydrogels have potential application as drug delivery matrices in controlled drug release.     

Thermosensitive Injectable Gradient Hydrogel-Induced Bidirectional Differentiation of BMSCs

Osteochondral defects threaten the quality of life of patients to a great extent. To simulate gradient changes in osteochondral tissue, a gradient-mixing injection device consisting of a controller and injection pumps is design. Bioactive glass (BG) and gellan gum (GG) are used to prepare thermosensitive injectable gradient hydrogels (B_0.5G, B₁G) with an upper critical solution temperature (UCST) range of 37.7–40.2 °C using this device for the first time. The mechanical properties of gradient hydrogels are significantly better than those of pure GG hydrogels. The gradients in the composition, structure, and morphology of gradient hydrogels are confirmed via physicochemical characterization. Cytocompatibility tests show that hydrogels, especially B_0.5G gradient hydrogels, promote the proliferation of bone marrow mesenchymal stem cells (BMSCs). Most importantly, qRT-PCR shows that the different components in B_0.5G gradient hydrogels simultaneously induce the osteogenic and chondrogenic differentiation of BMSCs. Experimental injection in porcine osteochondral defects indicates that the B_0.5G gradient hydrogel seamlessly fills irregular osteochondral defects in a less invasive manner by controlling the temperature to avoid cellular and tissue damage arising from crosslinkers or other conditions. These results show that thermosensitive injectable B_0.5G gradient hydrogels have the potential for less invasive integrated osteochondral repair.     

Synthesis and Swelling Properties of Thermosensitive Hydrogels based on Terpolymerization

Novel thermosensitive hydrogels based on polymerization of N-isopropyl acrylamide, Sodium acrylate, and diacetone acrylamide were synthesized, The swelling ratio and dynamic swelling were investigated. The results indicated that the hydrogels exhibited high water uptake and themosensitivity. The swelling properties and volume phase transition temperature could be adjusted by contents of the comonomers in the gels.