乙烯基硅烷-丙烯酸酯乳液共聚动力学研究

以乙烯基三乙氧基硅烷(VTES)、丙烯酸酯为单体,乙氧基醇磺基琥珀酸二钠(A—102)为乳化剂,合成了有机硅改性丙烯酸酯共聚乳液。研究了乳化剂、引发剂、VTES、反应温度以及功能性单体甲基丙烯酸羟乙酯(HEMA)对乳液共聚反应速率的影响。结果表明:聚合速率随乳化剂浓度、引发剂浓度、HEMA浓度的增大及反应温度的升高而增大,但随VTES浓度增大而逐渐减小。由实验得出恒速阶段聚合反应速率R_p与乳化剂浓度C_E、引发剂浓度C_1及有机硅单体浓度C_(VTES)的关系为R_p∝C_E~(0.35)C_I~(0.48)C_(VTES)~(-0.64),表观活化能E_a为81.1kJ·mol~(-1)。     

荧光探针法研究核壳结构有机硅-丙烯酸酯乳液的聚合行为

以芘为荧光探针,探讨了有机硅-丙烯酸酯核壳乳液聚合过程中,芘的第一振动峰(373 nm处)与第三振动峰(384 nm处)荧光强度的比值I1/I3与乳化剂、有机硅单体(D4)和引发剂(KPS)用量之间的关系,并结合聚合过程中探针芘的I1/I3峰值与单体转化率及乳胶粒形态演变之间的关系,研究了核壳结构有机硅-丙烯酸酯乳液的聚合行为.研究结果表明,探针芘的I1/I3峰值随乳化剂用量,D4用量,KPS用量不同发生相应的变化,随单体转化率的增加而增大.当乳化剂用量、D4用量、KPS与总单体的质量比依次为2 g、8 g、0.7%时,得到的乳液具有优良的综合性能.聚合反应过程中,当种子乳胶粒转变为核壳乳胶粒时,芘的I1/I3峰值仍呈现出明显的转变,说明有机硅-丙烯酸酯核壳乳液具有互穿聚合物网络结构.因此,荧光探针可用于研究有机硅-丙烯酸酯核壳乳液聚合反应进程.     

硅丙乳液的合成工艺研究

采用半连续种子乳液聚合工艺,以乙烯基三乙氧基硅烷(VTS)为改性剂、十二烷基硫酸钠(SDS)和烷基酚聚氧乙烯醚(OP-1O)为复合乳化体系,在引发剂过硫酸铵(APS)的作用下合成稳定的硅丙乳液.利用红外光谱(FTIR)和扫描电镜(SEM)对涂膜进行了表征.结果表明:单体转化率随乳化剂用量、引发剂用量、有机硅用量、聚合温...     

含氟接枝共聚物为助稳定剂的苯乙烯细乳液聚合反应

以含氟接枝共聚物(PSG)单独作为助稳定剂,十二烷基硫酸钠(SDS)为乳化剂,过硫酸钾(KPS)为引发剂引发苯乙烯(St)的细乳液聚合。考察了聚合温度、乳化剂用量、引发剂用量和PSG用量对细乳液聚合转化率的影响。结果表明,以PSG单独作为助稳定剂,细乳液聚合过程较稳定,起始单体液滴数目与成核粒子数目几乎相等。最终转化率随着乳化剂用量和反应温度的提高而增加,引发剂用量影响不明显。在相同的反应条件下,分别以相同用量(w.t.%=0.091%时,占单体和水的总质量)的PSG和十六醇为助稳定剂用于苯乙烯细乳液聚合,反应290min后,PSG体系的聚合转化率达到87.2%,而十六醇体系的聚合转化率只有78.2%。     

苯丙乳液合成反应条件优化

以苯乙烯、丙烯酸、丙烯酸丁酯、甲基丙烯酸甲酯等为单体,采用乳液聚合制备了苯丙乳液,研究了合成温度、引发剂用量、乳化剂用量、功能性单体丙烯酸用量等反应条件对苯丙乳液性能的影响,并探讨了丙烯酸单体对乳液耐酸碱稳定性的影响,确定了合成反应条件.结果表明,随着合成温度的提高,混合单体的转化率迅速增加,78℃时转化率最大(达到97.1%),而后随温度继续提高基本保持不变.混合单体转化率随过硫酸钾引发剂用量的增加呈现先增加后逐渐降低的趋势,当过硫酸钾与混合单体质量比为0.010时转化率最大,此时单体转化完全.此外,随着乳化剂用量增加,乳液的外观、钙离子稳定性、凝胶等性能都有所提高,但吸水率也相应增加.最佳合成反应条件为:合成温度为78℃,混合单体组成为15g苯乙烯、2g丙烯酸、18g丙烯酸丁酯、8g甲基丙烯酸甲酯,引发剂和乳化剂与单体质量比分别为0.010和0.035.得到的苯丙乳液在酸性条件下具有良好的稳定性.     

高固含量低粘度丙烯酸酯乳液压敏胶的制备

采用常规种子乳液聚合法合成出了固含量为65%、粘度小于400mPa·s的乳液压敏胶,研究了共聚单体、乳化剂、引发剂、缓冲剂及种子乳液量对丙烯酸酯共聚物乳液粘度和聚合稳定性的影响。结果表明:含羧基和羟基的功能单体对乳液的粘度和聚合稳定性影响较大;乳液压敏胶粘度随乳化剂量在预乳化液中所占比例增大及种子乳液量的增大而增大,随引发剂过硫酸铵(APS)用量增大而降低,随缓冲剂碳酸氢钠在预乳化液中所占比例增大先增大后减小;乳液压敏胶的聚合凝胶率随乳化剂量在预乳化液中所占比例增大及种子乳液量降低而减小,当APS为单体量的0.3%,NaHCO3在预乳化液和反应中的比例为2/4时,乳液凝胶率最低。     

有机硅氧烷改性St/BA/AA三元共聚乳液的制备

采用核壳乳液聚合法,制备了乙烯基三乙氧基硅烷（VTES）改性的St/BA/AA三元共聚乳液,其结构经FT IR确证。研究了VTES用量、乳化剂用量及配比和引发剂用量对单体转化率和粒径的影响。结果表明：在最优条件［48%St, 48%BA, 4%AA, 1%N-MA, 4%VTES, 8%乳化剂（OP-10/SDS=1/3）, 0.8%引发剂］下,单体转化率为95.8%,平均粒径242 nm。并研究了改性St/BA/AA乳胶膜(1)的耐溶剂性和铅笔硬度。结果表明：1具有良好的耐溶剂性,铅笔硬度为2H。     

光引发常规乳液聚合制备氨基聚苯乙烯纳米粒子

采用一种简单易行的方法制备了氨基功能化的聚苯乙烯纳米粒子.首先,采用4-乙烯基苄氯与1,3-丙二胺置换反应制备了含有氨基功能基团的可聚合单体N-(3-氨基丙基)对乙烯基苄基亚胺(CVPD).然后,采用乳液聚合,以苯乙烯(St)和CVPD为共聚单体,水溶性的4-(2-羟乙氧基)苯基-(2-羟基-2-丙基)酮(Irgacure 2959)为光引发剂,十六烷基三甲基溴化铵(CTAB)为乳化剂,经紫外光辐照引发,合成了P(St-co-CVPD)二元共聚物的纳米胶乳.体系的乳化剂用量仅为体系总质量的0.1 wt%～0.8 wt%,远小于常用来制备纳米粒子的微乳液体系的乳化剂用量.用透射电子显微镜(TEM)和激光粒度分析仪(DLS)表征了P(St-co-CVPD)纳米粒子的粒径和粒径分布.用红外光谱(FTIR)和核磁共振(NMR)证明了P(St-co-CVPD)纳米粒子上氨基的存在,并通过茚三酮显色反应定量检测了氨基含量.分别研究了单体配比,引发剂浓度,乳化剂用量以及紫外光强度对反应体系的影响.实验结果表明,产物粒子尺寸为30～600 nm,氨基通过共价键连接在粒子上,其含量为1.2×10-5～1.6×10-4 mol/g.该乳液体系聚合反应速率较快,单体转化率在60 min内即可达到80%.所得粒子的氨基含量可以通过单体配比进行调节.粒子尺寸可通过单体配比,引发剂浓度,乳化剂用量以及紫外光强度进行调节.     

氯丁胶乳乳液接枝甲基丙烯酸甲酯反应动力学

采用乳液聚合法将甲基丙烯酸甲酯(MMA)接枝到氯丁胶乳上,红外光谱和核磁共振氢谱证实了接枝产物的生成。研究了反应温度、乳化剂浓度、引发剂浓度和单体浓度对表观聚合速率的影响。结果表明,当反应温度为50℃,引发剂叔丁基过氧化氢-四乙烯五胺(t-BHP/TEPA)用量为氯丁胶乳干重的0.5%,单体/聚合物质量比m(M):m(P)=3:5,乳化剂十二烷基连苯醚二磺酸钠(DSB)用量为单体总质量1%时,单体转化率和接枝效率分别为99.1%和54.9%。聚合反应动力学关系式为:Rp=Kc(E)0.15c(I)0.30c(MMA)1.41,式中,K为常数,在40～55℃范围内,聚合反应的表观活化能Ea=60.2kJ/mol。接枝聚合基本符合自由基反应机理。     

反相乳液共聚合制备两性丙烯酰胺共聚物的研究

采用Span80-Tween80复合乳化剂和AIBA引发剂,进行丙烯酸钠(NaAA)/丙烯酰胺(AM)/丙烯酰氧基乙基三甲基氯化铵(DAC)反相乳液共聚合.研究了聚合温度、引发剂用量、单体浓度、共聚单体中DAC和AM含量、乳化剂用量及其HLB值、水/油比和水相pH值等聚合反应工艺条件或参数对聚合反应单体转化率和聚合物特性粘度的影响,聚合物特性粘度随引发剂用量和单体浓度的增大而增大的实验结果证实了该两性丙烯酰胺共聚物反相乳液制备过程中凝胶效应的存在.傅立叶红外光谱组成分析表明了两性丙烯酰胺共聚物的成功合成,扫描电镜观测乳胶粒粒径范围在0.6~8.0μm.     

HEPT类化合物的QSAR研究

为定量结构／活性相关性研究提取了量子化学参数,拓扑指数Am,分子连接性指数^mxt及疏水性常数,同时应用正交变换和最佳变量子集算法（Leaps-and-Bonds)进行了变量压缩和选择,进而实施了多元回归分析,并由此结果进行了HEPT类化合物（1－[(2-hydroxyethoxy)methyl]-6-(phenylthio)-thymine derivatives)的结构／活性关系的理论解释,进行了人工神经网络法对于该类化合物的活性预测,其结构明显好于多元回归法。     

From the Micro- to the Macro-: Managing the Conservation of the Warship,Vasa

Sweden's famous warship, Vasa, sank on her maiden voyage in August 1628, and remained on the bottom of Stockholm harbour for 333 years. Raised in 1961, she became the first large-scale wooden object to be treated with polyethylene glycol (PEG). In the summer of 2000 a number of acidic salt precipitations were noticed on the surface of the ship and on wooden artefacts in the storerooms. An international research project has been established to look into the causes of this problem and suggest possible re-treatments. Meanwhile projects are underway to monitor movements in the ship, to build a better support system, and to replace the thousands of iron bolts holding the structure together, while a sophisticated new climate system has recently been installed in the museum.     

液滴荧光传感与计算机联用技术在微量分析中的应用

通过在LS55型荧光-磷光-发光分光光度计上加装液滴产生及调节附件,采用计算机采集与分析处理数据,成功地研制了双通道液滴光化学传感装置.利用葡聚糖凝胶对复合维生素B中不同组分的选择性吸附来达到分离与同时检测的目的,并将其用于复合维生素B药片的分析,取得了满意的结果.     

On the scaling of the interface energy of the liquid clusters in the disordered nanoporous medium

Similarity of the extrusion curves of non-wetting liquid in a nanoporous medium with different initial fill volume fractions is observed experimentally. The similarity can be explained by the scaling of the interface energy and the self-similarity of the infinite percolation cluster of fluid-filled pores. Understanding the physical processes leading to the observed phenomena is a foundation for the development of high-performance devices for damping and energy storage on the basis of such heterogeneous systems.     

Using of the Agglomeration-in-liquid for the Technology of the Fine Materials

The content of the fine and ultrafine particles in the raw material results in difficulty of the separation, the loss of the valuable components and ecological contamination. Secondary using of the fine particles is impossible without their granulation. This problem has been solved by the agglomeration-in-liquid method.An agglomeration-in-liquid method is a process to produce agglomerates in a liquid phase from solid particles suspended in the liquid. The surface of solid particles and the binding liquid must be of identical polarity, but the continuous phase must be of the opposite polarity. The water solutions of the surfactant are the binding liquids or the organic liquids.     

Copper-containing dendromesogens: the influence of the metal on the mesomorphism

The synthesis and liquid crystalline behaviour of the first and second generations of a dendrimeric structure based on poly(propyleneimine)(DAB-dendr(NH₂)_x) are reported. 4-(4-n-Alkoxybenzoyloxy)salicylaldehydes are used as mesogenic moieties attached at the peripheral amino groups of the dendrimers giving rise to dendromesogens with four and eight mesogenic branches. From these dendromesogens, considered as organic ligands, were prepared six metal-containing dendrimers which incorporate two or four copper atoms in their structures. All the dendrimeric ligands and three of the metal-containing dendrimers exhibit liquid crystalline properties which were studied by optical microscopy, DSC, X-ray diffraction and EPR spectroscopy.     

On the quality of the hardness kernel and the Fukui function to evaluate the global hardness

An approximated hardness kernel, which includes the second derivative with respect to the density of the kinetic energy, the electron-electron coulomb repulsion, and the exchange density functionals, has been tested for the calculation of the global hardness. The results obtained for a series of 40 cations and neutral systems and 16 anions represent in most cases an improvement of the results obtained using the HOMO-LUMO gap approach and indicate the viability of this approach to evaluate global hardness. In addition, the relevance of the Fukui function approximation and the role of the three components of the hardness kernel in the evaluation of the global hardness have been analyzed.     

光亮剂对银电沉积行为的影响

用电势阶跃法和旋转圆盘电极法 (RDE)以及SEM和XRD测试手段 ,初步研究了光亮剂对氰化体系中银电沉积行为的影响 .研究表明 ,光亮剂的加入并未导致银电沉积成核机理的改变 ,但显著增强了镀液的微观平整效应 ,并且所得镀层的表观光滑程度明显改善 .XRD测试亦同时表明光亮剂的加入并未改变镀层的择优取向     

Influence of the Position of the Connecting Spacer of the Chromophore on the Nonlinear Optical Response

A new chromophore, C1 , based on a similar DπA‐structure as in the FTC ‐chromophore but with a hydroxyalkyl spacer perpendicular to the direction of the dipole moment was synthesized. Both chromophores and the CLD ‐chromophore were used to prepare high T_g nonlinear optical vinyl polymers. The influence of the position of the spacer on the DπA‐system on the NLO response of the resulting polymers was investigated.