Synergistic effects of combining ultrasound with the Fenton process in the degradation of Reactive Blue 19

The decoloration of reactive dye C.I. Reactive Blue 19 (RB 19) using combined ultrasound with the Fenton process has been investigated. The effect of varying the concentrations of hydrogen peroxide and iron sulfate, initial pH, ultrasonic power, initial dye concentration and dissolved gas on the decoloration and degradation efficiencies was measured. Calibration of the ultrasound systems was performed using calorimetric measurements and oxidative species monitoring using the Fricke dosimeter and degradations were carried out with a 20 kHz probe type transducer at 2, 4, 6 and 8 W cm⁻² of acoustic intensity at 15, 25, 50 and 75 mg L⁻¹ initial dye concentrations. First order rate kinetics was observed. It was found that while the degradation rate due to ultrasound alone was slow, sonication significantly accelerated the Fenton reaction. While the results were similar to those reported for other dyes, the effects occurred at lower concentrations. The rate and extent of decoloration of RB 19 increased with rising hydrogen peroxide concentration, ultrasonic powers and iron sulfate concentration but decreased with increasing dye concentration. An optimum pH value of pH = 3.5 was found. The rate of decoloration was higher when dissolved oxygen was present as compared with nitrogen and argon confirming the solution phase mechanism of the degradation.     

Degradation of Acid Blue 25 in aqueous media using 1700 kHz ultrasonic irradiation: ultrasound/Fe(II) and ultrasound/H2O2 combinations

In this work, the sonolytic degradation of an anthraquinonic dye, C.I. Acid Blue 25 (AB25), in aqueous phase using high frequency ultrasound waves (1700 kHz) for an acoustic power of 14 W was investigated. The sonochemical efficiency of the reactor was evaluated by potassium iodide dosimeter, Fricke reaction and hydrogen peroxide production yield. The three investigated methods clearly show the production of oxidizing species during sonication and well reflect the sonochemical effects of high frequency ultrasonic irradiation. The effect of operational conditions such as the initial AB25 concentration, solution temperature and pH on the degradation of AB25 was studied. Additionally, the influence of addition of salts on the degradation of dye was examined. The rate of AB25 degradation was dependent on initial dye concentration, pH and temperature. Addition of salts increased the degradation of dye. Experiments conducted using distilled and natural waters demonstrated that the degradation was more efficient in the natural water compared to distilled water. To increase the efficiency of AB25 degradation, experiments combining ultrasound with Fe(II) or H₂O₂ were conducted. Fe(II) induced the dissociation of ultrasonically produced hydrogen peroxide, leading to additional OH radicals which enhance the degradation of dye. The combination of ultrasound with hydrogen peroxide looks to be a promising option to increase the generation of free radicals. The concentration of hydrogen peroxide plays a crucial role in deciding the extent of enhancement obtained for the combined process. The results of the present work indicate that ultrasound/H₂O₂ and ultrasound/Fe(II) processes are efficient for the degradation of AB25 in aqueous solutions by high frequency ultrasonic irradiation.     

Decolorization of azo dye Orange G by aluminum powder enhanced by ultrasonic irradiation

In this work, the decolorization of azo dye Orange G (OG) in aqueous solution by aluminum powder enhanced by ultrasonic irradiation (AlP-UI) was investigated. The effects of various operating operational parameters such as the initial pH, initial OG concentration, AlP dosage, ultrasound power and added hydrogen peroxide (H₂O₂) concentration were studied. The results showed that the decolorization rate was enhanced when the aqueous OG was irradiated simultaneously by ultrasound in the AlP-acid systems. The decolorization rate decreased with the increase of both initial pH values of 2.0–4.0 and OG initial concentrations of 10–80 mg/L, increased with the ultrasound power enhancing from 500 to 900 W. An optimum value was reached at 2.0 g/L of the AlP dosage in the range of 0.5–2.5 g/L. The decolorization rate enhanced significantly by the addition of hydrogen peroxide in the range of 10–100 mM to AlP-UI system reached an optimum value of 0.1491 min⁻¹. The decolorization of OG appears to involve primarily oxidative steps, the cleavage of NN bond, which were verificated by the intermediate products of OG under the optimal tested degradation system, aniline and 1-amino-2-naphthol-6,8-disulfonate detected by the LC–MS.     

Degradation of Acid Orange 7 in aqueous solution by zero-valent aluminum under ultrasonic irradiation

Degradation of azo dye Acid Orange 7 (AO7) by zero-valent aluminum (ZVAl) in combination with ultrasonic irradiation was investigated. The preliminary studies of optimal degradation methodology were conducted with sole ultrasonic, sole ZVAl/air system, ultrasonication + ZVAl/air system (US-ZVAl). In ZVAl/air system, the degradation of AO7 could almost not be observed within 30 min. The degradation of AO7 by ZVAl/air system was obviously enhanced under ultrasound irradiation, and the enhancement is mainly attributed to that the production of hydroxyl radicals in ultrasound-ZVAl process was much higher than that in sole ultrasonic or in sole ZVAl/air system. The variables considered for the effect of degradation were the power of ultrasound, the initial concentration of AO7, as well as the initial pH value and the dosage of zero-valent aluminum. The results showed that the decolorization rate increased with the increase of power density and the dosage of ZVAl, but decreased with the increase of initial pH value and initial concentration of AO7. More than 96% of AO7 removal was achieved within 30 min under optimum operational conditions (AO7: 20 mg/L, ZVAl: 2 g/L, pH: 2.5, ultrasound: 20 kHz, 300 W). This study demonstrates that ultrasound-ZVAl process can effectively decolorize the azo dye AO7 in wastewater.     

Effect of intensifying additives on the degradation of thiamethoxam using ultrasound cavitation

The present study has investigated the degradation of thiamethoxam using ultrasound cavitation (US) operated at a frequency of 20 kHz and its combination with intensifying additives viz. hydrogen peroxide, Fenton and photo-Fenton reagent. At the outset, the performance of US (20 kHz) has been maximised by the optimization of process parameters. Highest rate of degradation of thiamethoxam was observed at the optimum ultrasonic power density of 0.22 W/mL, thiamethoxam concentration of 10 ppm and the pH of 2. The established optimum values of operating parameters were used further in case of combined treatment approaches. The effect of concentration of H₂O₂ on the rate of degradation of thiamethoxam in the case of US + H₂O₂ process has confirmed the existence of optimum concentration of H₂O₂ with the ratio of thiamethoxam: H₂O₂ as 1:10. US + Fenton process indicated the optimal molar ratio of FeSO₄·7H₂O:H₂O₂ as 1:15. The combined processes of US + H₂O_2, US + Fenton and US + photo-Fenton have resulted in the extent of degradation of 20.47 ± 0.61%, 34.41 ± 1.03% and 85.17 ± 2.56% respectively after 45 min. of operation. These combined processes lead to the synergistic index of 2.04 ± 0.06, 2.26 ± 0.07 and 2.42 ± 0.07 in case of US + H₂O₂, US + Fenton and US + photo-Fenton processes respectively over only US/stirring treatment with the additive. Additionally, the extent of mineralization and the energy efficiency of individual and combined processes have been compared. US + photo-Fenton process has been found to be the best strategy for effective degradation of thiamethoxam with a significant intensification benefit. The by-products formed during the ultrasonic degradation of thiamethoxam have been identified by using LC-MS/MS analysis.     

Catalytic activity of copper (II) oxide prepared via ultrasound assisted Fenton-like reaction

Copper (II) oxide nanoparticles were synthesized in an ultrasound assisted Fenton-like aqueous reaction between copper (II) cations and hydrogen peroxide. The reactions were initiated with the degradation of hydrogen peroxide by ultrasound induced cavitations at 0 °C or 5 °C and subsequent generation of the OH radical. The radical was converted into hydroxide anion in Fenton-like reactions and copper hydroxides were readily converted to oxides without the need of post annealing or aging of the samples. The products were characterized with X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and Brunauer–Emmett–Teller (BET) surface area analysis. Catalytic activity of the nanoparticles for the hydrogen peroxide assisted degradation of polycyclic aromatic hydrocarbons in the dark was tested by UV–visible spectroscopy with methylene blue as the model compound. The rate of the reaction was first order, however the rate constants changed after the initial hour. Initial rate constants as high as 0.030 min⁻¹ were associated with the high values of surface area, i.e. 70 m²/g. Annealing of the products at 150 °C under vacuum resulted in the decrease of the catalytic activity, underlying the significance of the cavitation induced surface defects in the catalytic process.     

Intensified sonochemical degradation of 2-Picoline in combination with advanced oxidizing agents

2-picoline is a very important pyridine derivative with significant applications though it is also poisonous and harmful having considerable adverse influence on aquatic life, environment and organisms. The need for developing effective treatment methodologies for 2-Picoline directed the current work focusing on degradation of 2-Picoline using the combination of ultrasound and advanced oxidants such as hydrogen peroxide (H₂O₂), potassium persulphate (KPS), Fenton’s reagent, and Peroxymonosulphate (PMS) along with the use of Titanium oxide (TiO₂) as catalyst. Ultrasonic bath having 8 L capacity and operating frequency of 40 ± 2 kHz has been used. The effect of parameters like power, initial pH, temperature, time and initial concentration of 2-Picoline were studied to establish best operating conditions which were further used in the combination treatment approaches of ultrasound with oxidising agents. The chemical oxygen demand (COD) reduction for the optimized approaches of ultrasound in combination with oxidizing agents was also determined. Degradation experiments were performed using oxidising agents also in absence of ultrasound to investigate the individual treatment capacity of the oxidants and also the synergetic index for the combination. Kinetic study demonstrated that second order model suited for all the treatment approaches except US/Fenton where first order model fitted better. Ultrasound in combination with Fenton reagent demonstrated a substantial synergy for the degradation of 2-Picoline compared to other treatment approaches showing highest degradation of 97.6 %, synergetic index as 5.71, cavitational yield of 1.82 × 10⁻⁵ mg/J and COD removal of 82.4 %.     

Effect of potassium monopersulfate (oxone) and operating parameters on sonochemical degradation of cationic dye in an aqueous solution

In this study, removal of Cresol Red (CR), a cationic triphenylmethane dye, by 300 kHz ultrasound was investigated. The effect of additive such as potassium monopersulfate (oxone) was studied. Additionally, sonolytic degradation of CR was investigated at varying power and initial pH. RC can be readily eliminated by the ultrasound process. The obtained results showed that. Sonochemical degradation of CR was strongly affected by ultrasonic power and pH. The degradation rate of the dye increased substantially with increasing ultrasonic power in the range of 20–80 W. This improvement could be explained by the increase in the number of active cavitation bubbles. The significant degradation was achieved in acidic conditions (pH = 2) where the color removal was 99% higher than those observed in higher pH aqueous solutions. The ultrasonic degradation of dye was enhanced by potassium monopersulfate (oxone) addition. It was found that the degradation of the dye was accelerated with increased concentrations of oxone for a reaction time of 75 min.     

Extraction of phenolics and anthocyanins from purple eggplant peels by multi-frequency ultrasound: Effects of different extraction factors and optimization using uniform design

In this work, multi-frequency ultrasound (working modes for the single-, dual- and tri-frequency in simultaneous ways) was applied to extract bioactive compounds from purple eggplant peels. The single-factor experiments were performed by varying six independent variables. A six-level-five-factor uniform design (UD) was further employed to evaluate the interaction effects between different factors. It was found that extraction temperature and extraction time significantly affected the total phenolic content (TPC), whereas the total monomeric anthocyanins (TMA) was mainly influenced by ethanol concentration, extraction temperature and solid-liquid ratio. Based on partial least-squares (PLS) regression analysis, the optimal conditions for TPC extraction were: 53.6 % ethanol concentration, 0.336 mm particle size, 44.5 °C extraction temperature, 35.2 min extraction time, 1:43 g/mL solid-liquid ratio, and similar optimal conditions were also obtained for TMA. Furthermore, the TPC and TMA extraction were investigated by ultrasound in different frequencies and power levels. Compared with single-frequency (40 kHz) and dual-frequency ultrasound (25 + 40 kHz), the extraction yield of TPC and TMA with tri-frequency ultrasound (25 + 40 + 70 kHz) increased by 23.65 % and 18.76 % respectively, which suggested the use of multi-frequency ultrasound, especially tri-frequency ultrasound, is an efficient strategy to improve the TPC and TMA extracts in purple eggplant peels.     

Degradation of C.I. Acid Orange 7 by the advanced Fenton process in combination with ultrasonic irradiation

The combination of ultrasound and the advanced Fenton process (AFP, zero-valent iron and hydrogen peroxide) for the degradation of C.I. Acid Orange 7 was studied. The effect of hydrogen peroxide concentration, initial pH, ultrasonic power density, dissolved gas, and iron powder addition on the decolorization of C.I. Acid Orange 7 was investigated. A modified pseudo-first order kinetic model was used to simulate the experimental results. The results showed that the decolorization rate increased with the increase of hydrogen peroxide concentration and power density, but decreased with the increase of initial pH value. There existed an optimal iron powder addition when decolorization rate was concerned. The decolorization efficiency also increased with the increase of hydrogen peroxide concentration, but decreased with the increase of initial pH value. It varied little at different power densities or iron powder additions at the fixed hydrogen peroxide concentration. The presence of dissolved gas would enhance color removal, and the enhancement was more significant when dissolved oxygen was present. More hydrogen peroxide dosage and reaction duration are required to achieve a relatively high COD removal than those employed to simply break the chromophore group.     

Does power ultrasound affect hydrocarbon Ionomers?

The effect of low-frequency high-power ultrasound on hydrocarbon-based ionomers, cation exchange sulfonated phenylated polyphenylene (sPPB-H⁺) and anion exchange hexamethyl-p-terphenyl poly(benzimidazolium) (HMT-PMBI), was studied. Ionomer solutions were subjected to ultrasonication at fixed ultrasonic frequencies (f = 26 and 42 kHz) and acoustic power (P_acous = 2.1 – 10.6 W) in a laboratory-grade ultrasonication bath, and a probe ultrasonicator; both commonly employed in catalyst ink preparation in research laboratory scale. Power ultrasound reduced the polymer solution viscosity of both hydrocarbon-based ionomers. The molecular weight of sPPB-H⁺ decreased with irradiation time. Changes in viscosity and molecular weight were exacerbated when ultrasonicated in an ice bath; but reduced when the solutions contained carbon black, as typically used in Pt/C-based catalyst inks. Spectroscopic analyses revealed no measurable changes in polymer structure upon ultrasonication, except for very high doses, where evidence for free-radical induced degradation was observed. Ionomers subjected to ultrasound were used to prepare catalyst layers and membrane electrode assemblies (MEA)s. Despite the changes in the ionomer described above, no significant differences in electrochemical performance were found between MEAs prepared with ionomers pre-subjected to ultrasound and those that were not, suggesting that fuel cell performance is tolerant to ionomers subjected to ultrasound.     

Single,simultaneous and sequential applications of ultrasonic frequencies for the elimination of ibuprofen in water

The study is about the assessment of single and multi-frequency operations for the overall degradation of a widely consumed analgesic pharmaceutical-ibuprofen (IBP). The selected frequencies were in the range of 20–1130 kHz emissions coming from probes, baths and piezo-electric transducers attached to plate-type devices. Multi-frequency operations were applied either simultaneously as “duals”, or sequentially at fixed time intervals; and the total reaction time in all operations was 30-min. The work also covers evaluation of the effect of zero-valent iron (ZVI) on the efficiency of the degradation process and the performance of the reaction systems. It was found that low-frequency probe type devices especially at 20 kHz were ineffective when applied singly and without ZVI, and relatively more effective in combined-frequency operations in the presence of ZVI. The power efficiencies of the reactors and/or reaction systems showed that 20-kHz probe was considerably more energy intensive than all others, and was therefore not used in multi-frequency operations. The most efficient reactor in terms of power consumption was the bath (200 kHz), which however provided insufficient mineralization of the test chemical. The highest percentage of TOC decay (37%) was obtained in a dual-frequency operation (40/572 kHz) with ZVI, in which the energy consumption was neither low nor exceptionally too high. A sequential operation (40 + 200 kHz) in that respect was more efficient, because it required much less energy for a similar TOC decay performance (30%). In general, the degradation of IBP increased with increased power consumption, which in turn reduced the sonochemical yield. The study also showed that advanced Fenton reactions with ZVI were faster in the presence of ultrasound, and the metal was very effective in improving the performance of low-frequency operations.     

Understanding the effects of mineral water matrix on degradation of several pharmaceuticals by ultrasound: Influence of chemical structure and concentration of the pollutants

Degradation of seven relevant pharmaceuticals with different chemical structures and properties: acetaminophen (ACE), cloxacillin (CXL), diclofenac (DCF), naproxen (NPX), piroxicam (PXC), sulfacetamide (SAM) and cefadroxil (CDX), in distilled water and mineral water by ultrasound was studied herein. Firstly, proper conditions of frequency and acoustic power were determined based on the degradation ability of the system and the accumulation of sonogenerated hydrogen peroxide (24.4 W and 375 kHz were found as the suitable conditions for the sonochemical treatment of the pharmaceuticals). Under such conditions, the pharmaceuticals degradation order in distilled water was: PXC > DCF ~ NPX > CXL > ACE > SAM > CDX. In fact, the initial degradation rate showed a good correlation with the Log P parameter, most hydrophobic compounds were eliminated faster than the hydrophilic ones. Interestingly, in mineral water, the degradation of those hydrophilic compounds (i.e., ACE, SAM and CDX) was accelerated, which was attributed to the presence of bicarbonate ions. Afterwards, mineral water containing six different initial concentrations (i.e., 0.331, 0.662, 3.31, 16.55, 33.1, and 331 µM) of selected pharmaceuticals was sonicated, the lowest concentration (0.331 µM) always gave the highest degradation of the pollutants. This result highlights the great ability of the sonochemical process to treat bicarbonate-rich waters containing pollutants at trace levels, as pharmaceuticals. Finally, the addition of ferrous ions to the sonochemical system to generate a sono-Fenton process resulted in an acceleration of degradation in distilled water but not in mineral water. This was attributed to the scavenging of sonogenerated HO• by bicarbonate anion, which decreases H₂O₂ accumulation, thus limiting the Fenton reaction.     

Sonochemical degradation of trimethoprim in water matrices: Effect of operating conditions,identification of transformation products and toxicity assessment

The sonochemical degradation of trimethoprim (TMP), a widely used antibiotic, in various water matrices was investigated. The effect of several parameters, such as initial TMP concentration (0.5–3 mg/L), actual power density (20–60 W/L), initial solution pH (3–10), inorganic ions, humic acid and water matrix on degradation kinetics was examined. The pseudo-first order degradation rate of TMP was found to increase with increasing power density and decreasing pH, water complexity (ultrapure water > bottled water > secondary wastewater) and initial TMP concentration.TMP degradation is accompanied by the formation of several transformation products (TPs) as evidenced by LC-QToF-MS analysis. Nine such TPs were successfully identified and their time-trend profiles during degradation were followed. An in silico toxicity evaluation was performed showing that several TPs could potentially be more toxic than the parent compound towards Daphnia magna, Pimephales promelas and Pseudokirchneriella subcapitata.     

Synergetic decolorization of azo dyes using ultrasounds,photocatalysis and photo-fenton reaction

In the present work, ultrasound irradiation, photocatalysis with TiO₂, Fenton/Photo-Fenton reaction, and the combination of those techniques were investigated for the decolorization of industrial dyes in order to study their synergy. Three azo dyes were selected from the weaving industry. Their degradation was examined via UV illumination, Fenton and Photo-Fenton reaction as well as ultrasound irradiation at low (20 kHz) and high frequencies (860 kHz). In these experiments, we investigated the simultaneous action of the ultrasound and UV irradiation by varying parameters like the duration of photocatalysis and ultrasound irradiation frequency. At the same time, US power, temperature, amount of TiO₂ photocatalyst and amount of Fenton reagent remained constant. Due to their diverse structure, each azo dye showed different degradation levels using different combinations of the above-mentioned Advanced Oxidation Processes (AOPs). The Photo-Fenton reagent is more effective with US 20 kHz and US 860 kHz for the azo dyes originated from the weaving industry at pH = 3 as compared to pH = 6.8. The combination of the Photo-Fenton reaction with 860 kHz ultrasound irradiation for the same dye gave an 80% conversion at the same time. Experiments have shown a high activity during the first two hours. After that threshold, the reaction rate is decreased. FT-IR and TOC measurements prove the decolorization due to the destruction of the chromophore groups but not complete mineralization of the dyes.     

Degradation of 4-chloro 2-aminophenol using combined strategies based on ultrasound,photolysis and ozone

The present work investigates the degradation of 4-chloro 2-aminophenol (4C2AP), a highly toxic organic compound, using ultrasonic reactors and combination of ultrasound with photolysis and ozonation for the first time. Two types of ultrasonic reactors viz. ultrasonic horn and ultrasonic bath operating at frequency of 20 kHz and 36 kHz respectively have been used in the work. The effect of initial pH, temperature and power dissipation of the ultrasonic horn on the degradation rate has been investigated. The established optimum parameters of initial pH as 6 (natural pH of the aqueous solution) and temperature as 30 ± 2 °C were then used in the degradation studies using the combined approaches. Kinetic study revealed that degradation of 4C2AP followed first order kinetics for all the treatment approaches investigated in the present work. It has been established that US + UV + O₃ combined process was the most promising method giving maximum degradation of 4C2AP in both ultrasonic horn (complete removal) and bath (89.9%) with synergistic index as 1.98 and 1.29 respectively. The cavitational yield of ultrasonic bath was found to be eighteen times higher as compared to ultrasonic horn implying that configurations with higher overall areas of transducers would be better selection for large scale treatment. Overall, the work has clearly demonstrated that combined approaches could synergistically remove the toxic pollutant (4C2AP).     

Quantification of frequency dependence of mechanical effects induced by ultrasound

The physical or mechanical effects induced by ultrasound were investigated through the viscosity change in degradation of polymers. The viscosity change was observed with polyethylene oxide in both aqueous and benzene solution; while polystyrene in only benzene solution. The frequency of ultrasound in these experiments varies from 20 kHz to 1 MHz, under a constant dissipated power. The viscosity ratio and the apparent degradation rate were obtained as a function of the irradiation frequency. From the analysis of these experiments, the mechanical effects are found to slow down above 100 kHz when the frequency increases. In case of the analysis of solution viscosity, since this method yields the same apparent results in both aqueous and benzene solutions, our study propose an alternative simple, cost effective method to quantify the mechanical effects in sonochemistry.     

Sonochemical degradation of 3-methylpyridine (3MP) intensified using combination with various oxidants

3-Methyl pyridine (3MP) is a toxic and hazardous organic compound having considerable negative impact on environment and living organisms. The objective of this work to report a novel treatment strategy based on sonochemical degradation of 3MP, in combination with oxidants such as hydrogen peroxide, Fenton’s reagent, peroxymonosulphate (PMS), and potassium persulphate (KPS) as well as solar irradiations. A bath sonicator operating at 25 kHz frequency and rated power dissipation of 100 W was applied in the work to study different approaches with an objective to enhance the removal of 3MP in lesser time. Effect of operating parameters such as pH (over the range of 2–10), treatment time, temperature (25–55 °C) and ultrasonic power (25 W to 150 W) on the degradation has been studied and the best conditions were used in subsequent combination approaches. It was demonstrated that ultrasound in combination with PMS, ferrous sulphate (FeSO₄) and solar irradiations (approach of US/PMS/FeSO₄/solar irradiation) is the best treatment strategy yielding maximum degradation as 97.4% with highest cavitational yield as 1.920 × 10⁻⁴ mg/J and highest synergetic Index as 2.70. Kinetic analysis revealed that first order mechanism fitted well to all the approaches involving different combinations of ultrasound, oxidising agents and solar irradiation. Degradation products were also analysed that established the degradation mechanism as C₂ and C₃ ring cleavages forming 1, 4-dihydro3-methylpyridine followed by Levulinic acid as non -toxic main by-product. Overall the work clearly demonstrated an effective treatment approach involving combined sonication with oxidants for remediation of 3MP also providing insights on kinetics and mechanism of degradation.     

Novel approaches based on ultrasound for treatment of wastewater containing potassium ferrocyanide

Industrial wastewaters containing biorefractory compounds like cyanide offer significant environmental problems attributed to the fact that the conventional methods have limited effectiveness and hence developing efficient treatment approaches is an important requirement. The present work investigates the use of novel treatment approach of ultrasound (US) combined with advanced oxidation techniques for the degradation of potassium ferrocyanide (KFC) for the first time. An ultrasonic bath equipped with longitudinal horn (1 kW rated power and 25 kHz frequency) has been used. The effect of initial pH (2–9) on the progress of degradation has been investigated initially and subsequently using the optimized pH, effect of addition of hydrogen peroxide (ratio of KFC:H₂O₂ varied over the range of 1:0.5–1:5) and TiO₂ in the presence of H₂O₂ (1:1 ratio by weight of TiO₂) as process intensifying approach has been studied. Combination of ultrasonic irradiation with ozone (O₃) (100–400 mg/h) and ultraviolet irradiation (UV) has also been investigated. Use of combination of US with H₂O_2, H₂O₂ + TiO₂ and ozone resulted in extent of KFC degradation as 54.2%, 74.82% and 82.41% respectively. Combination of US with both UV and ozone was established to be the best approach yielding 92.47% degradation. The study also focused on establishing kinetic rate constants for all the treatment approaches which revealed that all the approaches followed first order kinetic mechanism with higher rate constants for the combination approaches. Overall, it has been conclusively established that ultrasound based combined treatment schemes are very effective for the treatment of KFC containing wastewaters.     

Optimization of ultrasound assisted extraction of abalone viscera protein and its effect on the iron-chelating activity

This study aims to investigate effects of ultrasound assisted extraction on the abalone viscera protein extraction rate and iron-chelating activity of peptides. The optimal conditions for ultrasound assisted extraction by response surface methodology was at sodium hydroxide concentration 14 g/kg, ultrasonic power 428 W and extraction time 52 min. Under the optimal conditions, protein extraction rate was 64.89%, compared with alkaline extraction of 55.67%. The iron-chelating activity of peptides affected by ultrasound technology was further evaluated by iron-chelating rate, FTIR spectroscopy and LC-HRMS/MS. Alcalase was the suitable enzyme for the preparation of iron-chelating peptides from two abalone viscera proteins, showing no significant difference between their iron-chelating rate of 16.24% (ultrasound assisted extraction) and 16.60% (alkaline extraction). Iron binding sites from the two hydrolysates include amino and carboxylate terminal groups and peptide bond of the peptide backbone as well as amino, imine and carboxylate from side chain groups. Moreover, 24 iron-chelating peptides were identified from hydrolysate (alcalase, ultrasound assisted extraction), which were different from the 27 iron-chelating peptides from hydrolysate (alcalase, alkaline extraction). This study suggests the application of ultrasound technology in the generation of abalone viscera-derived iron-chelating peptides which have the ability to combat iron deficiency.