Determination of trace amounts of nickel, manganese, cobalt, and zinc in environmental samples after separation and preconcentration by use of polyacrylic acid/alumina sorbent

Manganese, nickel, cobalt, and zinc are elements that appear together in many real samples. In this work, a simple, rapid, and sensitive method has been used for the simultaneous separation and preconcentration of trace amounts of these elements using water-soluble polyacrylic acid on alumina as a sorbent in a glass column system. A solution containing Mn, Ni, Co, and Zn was passed through the column at pH 7, and desorption was carried with 5.0 mL of 0.03 M nitric acid. Linearity was maintained between 0.25-5.0 x 10(3), 0.04-6.0 x 10(3), 0.10-8.0 x 10(3), and 0.028-1.0 x 10(3) ng/mL for Ni, Mn, Co, and Zn, respectively, in the original solution. Eight replicate determinations of a mixture containing 1.0 microg/mL of each of the elements in the final solution gave relative standard deviations of 1.4, 1.5, 2.4, and 1.2% for Ni, Mn, Co, and Zn, respectively. The sorption capacities for Mn (mg/g sorbent) obtained were 16.0 for Mn, 9.0 for Ni, 12.0 for Co, and 10.0 for Zn. By using 5.0 mL elution solution, preconcentration factors of 400, 500, 700, and 460 could be obtained for Ni, Mn, Zn, and Co, respectively.     

三元素氢氧化物中镍钴锰含量的测定

采用仪器分析方法和化学分析方法相结合测定三元前驱体Ni0.33Co0.33Mn0.33(OH)2中镍、钴、锰主含量,分别采用电感耦合等离子体原子发射光谱(ICP-AES)内标法测定镍、钴、锰的摩尔比例,EDTA滴定法测定镍、钴、锰的摩尔总量,计算得到各元素的含量。通过优化实验条件,进行了准确度和精密度实验,加标回收率为99.2%~101%,相对标准偏差小于0.65%。方法准确、快速,已用于实际的检测工作中。     

锌掺杂提高LiNi1/3Co1/3Mn1/3O2正极材料的电化学稳定性

通过共沉淀法与固相法相结合制备了掺锌的高稳定性Li(Ni_1/3Co_1/3Mn_1/3)_1-xZn_xO₂ (x=0, 0.02, 0.05)正极材料. 循环伏安(CV)曲线表明Zn掺杂使氧化峰与还原峰的电势差减小到0.09 V, 电化学阻抗谱(EIS)曲线表明Zn掺杂使电极的阻抗从266 Ω减小到102 Ω. Li⁺嵌入扩散系数从1.20×10^-11 cm²·s^-1增大到 2.54×10^-11 cm²·s^-1. Li(Ni_1/3Co_1/3Mn_1/3)_0.98Zn_0.02O₂正极材料以0.3C充放电在较高的截止电压(4.6 V)下比其他两种材料的电化学循环性能更稳定, 其第二周的放电比容量为176.2 mAh·g^-1, 循环100周后容量几乎没衰减; 高温(55 °C)下充放电循环100周, 其放电比容量平均每周仅衰减0.20%, 远小于其他两种正极材料(LiNi_1/3Co_1/3Mn_1/3O₂平均每周衰减0.54%; Li(Ni_1/3Co_1/3Mn_1/3)_0.95Zn_0.05O₂平均每周衰减0.38%). Li(Ni_1/3Co_1/3Mn_1/3)_0.98Zn_0.02O₂正极材料以3C充放电时其放电比容量可达142 mAh·g^-1, 高于其他两种正极材料. 电化学稳定性的提高归因于Zn掺杂后减小了电极的极化和阻抗, 增大了锂离子扩散系数.     

Effect of Various Synthesis methods on the Electrochemical Properties of LiNi1/3Co1/3Mn1/3O2

Layered LiNi1/3Co1/3Mn1/3O2 has the isostructure of α-NaFeO2 and shows high rate capacity with stable cycleability. Furthermore, the thermal behavior of this material is milder than that of lithium nickel oxide and lithium cobalt oxide. In addition, it is expected to be stable at elevated temperatures. Therefore LiNi1/3Co1/3Mn1/3O2 may be the most promising cathode materials of lithium-ion secondary battery.In this research, LiNi1/3Co1/3Mn1/3O2 was prepared by solid-state reaction, sol-gel method and mixed hydroxide method. The influences of synthesis method on the physical and electrochemical properties of LiNi1/3Co1/3Mn1/3O2 were characterized by means of X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM), charge/discharge cycling cyclic voltammetry and differential scanning calorimetry (DSC). XPS studies show that the predominant oxidation states of Ni, Co and Mn in the LiNi1/3Co1/3Mn1/3O2 compound are 2+, 3+ and 4+. From the voltage profile and cyclic voltammetry, the redox processes occurring at ～3.8V and ～4.5V are assigned to the Ni2+/Ni3+ and Co3+/Co4+ couples, respectively. Different preparation methods result in the difference in morphology (shape, particle size and specific surface area) and electrochemical behaviors. A sample prepared by solid-state reaction has the worst electrochemical performance among these three methods. Sample synthesized by mixed hydroxide method displays the better rate capacity than that prepared by sol-gel method, while the capacity retention of sample prepared by sol-gel method is superior to that synthesized by mixed hydroxide method.     

合成温度对全梯度正极材料LiNi0.7Co0.15Mn0.15O2的结构和电化学性能影响

通过控制结晶法和浓度梯度进料的方式制备了Ni、Co和Mn三元素组分含量呈全梯度分布的类球形Ni_0.7Co_0.15Mn_0.15（OH）₂前驱体,与LiOH·H₂O均匀混合并焙烧后获得LiNi_0.7Co_0.15Mn_0.15O₂正极材料,系统研究了不同焙烧温度对材料Ni、Co和Mn三元素扩散情况、晶体结构及电化学性能的影响规律。通过能谱仪（EDXS）分析不同焙烧温度下材料颗粒中Ni、Co、Mn三元素的扩散程度。研究结果表明,在800℃下焙烧得到的正极材料梯度分布特征明显且电化学性能最佳,首次放电比容量为186.1 mAh·g^-1（2.8~4.3 V,0.2C）,2C大倍率充放电条件下循环200次后容量保持率为90.1%。这种材料兼具高比容量及良好的循环稳定性,可以用作下一代高能量密度锂离子电池正极材料。     

Investigation of the charge compensation mechanism on the electrochemically Li-ion deintercalated Li1-xCo1/3Ni1/3Mn1/3O2 electrode system by combination of soft and hard X-ray absorption spectroscopy

In situ hard X-ray absorption spectroscopy (XAS) at metal K-edges and soft XAS at O K-edge and metal L-edges have been carried out during the first charging process for the layered Li1-xCo1/3Ni1/3Mn1/3O2 cathode material. The metal K-edge XANES results show that the major charge compensation at the metal site during Li-ion deintercalation is achieved by the oxidation of Ni2+ ions, while the manganese ions and the cobalt ions remain mostly unchanged in the Mn4+ and Co3+ state. These conclusions are in good agreement with the results of the metal K-edge EXAFS data. Metal L-edge XAS results at different charge states in both the FY and PEY modes show that, unlike Mn and Co ions, Ni ions at the surface are oxidized to Ni3+ during charge, whereas Ni ions in the bulk are further oxidized to Ni4+ during charge. From the observation of O K-edge XAS results, we can conclude that a large portion of the charge compensation during Li-ion deintercalation is achieved in the oxygen site. By comparison to our earlier results on the Li1-xNi0.5Mn0.5O2 system, we attribute the active participation of oxygen in the redox process in Li1-xCo1/3Ni1/3Mn1/3O2 to be related to the presence of Co in this system.     

The stability of the SEI layer, surface composition and the oxidation state of transition metals at the electrolyte-cathode interface impacted by the electrochemical cycling: X-ray photoelectron spectroscopy investigation

The stability of the valence state of the 3d transition metal ions and the stoichiometry of LiMO(2) (M = Co, Ni, Mn) layered oxides at the surface-electrolyte interface plays a crucial role in energy storage applications. The surface oxidation/reduction of the cations caused by the contact of the solids to air or to the electrolyte results in the blocking of the Li-transport through the interface that leads to the fast batteries deterioration. The influence of the end-of-charge voltage on the chemical composition and the oxidation state of 3d transition metal ions, as well as the stability of the solid-electrolyte interface formed during the electrochemical Li-deintercalation/intercalation of the LiCoO(2) and Li(Ni,Mn,Co)O(2), have been investigated by X-ray photoelectron spectroscopy. While the chemical composition of the solid-electrolyte interface is similar for both layered oxide surfaces, the electrochemical cycling to some critical voltage values leads to the disappearance of the interface. By the analysis of the shape of the 2p and 3s photoelectron emissions we show that the formation of the solid-electrolyte interface layer correlates with the partial reduction of the trivalent Co ions at the electrolyte-LiCoO(2) interface and the amount of the Co(2+) ions is increased as the solid-electrolyte interface vanishes. In contrast, the Mn(4+), Co(3+) and Ni(2+) ions of the Li(Ni,Mn,Co)O(2) are stable at the interface under the electrochemical cycling to higher end-of-charge voltage. A correlation between deterioration of the LiCoO(2) and Li(Ni,Mn,Co)O(2) batteries and the change of electronic structure at the surface/interface after the electrochemical cycling has been found. The dissolution of the solid-electrolyte interface layer might be the reason for the fast deterioration of the Li-ion batteries.     

Determination of trace metal ions by AAS in natural water samples after preconcentration of pyrocatechol violet complexes on an activated carbon column

A simple preconcentration method is described for the determination of Cu, Mn, Co, Cd, Pb, Ni and Cr in water samples by flame AAS. Trace metal ions in water were sorbed as pyrocatechol violet complexes on activated carbon column at the pH range of 4–8, then eluted with 1 M HNO₃ in acetone. The effect of major cations and anions of the natural water samples on the sorption of metal ions has been also investigated. The concentration of the metal ions detected after preconcentration was in agreement with the added amount. The present method was found to be applicable to the preconcentration of Cu, Mn, Co, Cd, Pb, Ni and Cr in natural water samples with good results such as R.S.D. from 3 to 8% (N=10) and detection limits under 70 ng l⁻¹.     

Local electronic structure of layered Li(x)Ni0.5Mn0.5O2 and Li(x)Ni(1/3)Mn(1/3)Co(1/3)O2

Samples of Li(x)Ni0.5Mn0.5O2 and Li(x)Ni(1/3)Mn(1/3)Co(1/3)O2 were prepared as active materials in electrochemical half-cells and were cycled electrochemically to obtain different values of Li concentration, x. Absorption edges of Ni, Mn, Co, and O in these materials of differing x were measured by electron energy loss spectrometry (EELS) in a transmission electron microscope to determine the changes in local electronic structure caused by delithiation. The work was supported by electronic structure calculations with the VASP pseudopotential package, the full-potential linear augmented plane wave code WIEN2K, and atomic multiplet calculations that took account of the electronic effects from local octahedral symmetry. A valence change from Ni2+ to Ni4+ with delithiation would have caused a 3 eV shift in energy of the intense white line at the Ni L3 edge, but the measured shift was less than 1.2 eV. The intensities of the "white lines" at the Ni L-edges did not change enough to account for a substantial change of Ni valence. No changes were detectable at the Mn and Co L-edges after delithiation either. Both EELS and the computational efforts showed that most of the charge compensation for Li+ takes place at hybridized O 2p states, not at Ni atoms.     

Tetraaza macrocyclic complexes: synthesis,spectral and antimicrobial studies

A tetradentate nitrogen donor [N₄] macrocyclic ligand, 1,3,7,9-tetraaza-2,8-dithia-4,10-dimethyl-6,12-diphenylcyclododeca-4,6,10,12-tetraene has been synthesized by using thiourea and benzoylacetone. Complexes of Mn(II), Co(II), Ni(II), and Cu(II) have been synthesized with this ligand and characterized by element chemical analysis, molar conductance, magnetic susceptibility, mass, ¹H nuclear magnetic resonance, Fourier transform–infrared, electronic, and electron paramagnetic resonance spectral studies. The molar conductance measurements of Mn(II), Co(II), and Cu(II) complexes in dimethyformamide correspond to nonelectrolytes, whereas Ni(II) complex is a 1: 2 electrolyte. The complexes are high-spin except for Ni(II) which is diamagnetic. Octahedral geometry has been assigned for Mn(II) and Co(II) complexes, square planar for Ni(II) and tetragonal geometry for Cu(II). The ligand and its complexes were screened in vitro against two pathogenic fungi (Fusarium moniliformae and Rhizoctonia solani) and bacteria (Staphylococcus aureus and Pseudomonas aeruginosa) to assess their growth inhibiting potential.     

Transition Metal Complexes of Dis(thiosemicarbazone): Synthesis and Spectral,and Antifungal Studies

Mn(II), Co(II), Ni(II), and Cu(II) complexes have been synthesized with benzil bis(thiosemicarbazone) (L) and characterized by elemental analyses, molar conductance measurements, magnetic susceptibility measurements, thermogravimetric studies, infrared (IR), electronic, and electron paramagnetic resonance (eEPR) spectral studies. The molar conductance measurements of the complexes in DMF correspond to the non-electrolytic nature of the complexes. Thus these complexes may be formulated as [M(L)X₂] (where M = Mn(II), Co(II), Ni(II), Cu(II) and X = Cl^? and NO₃ ^?). On the basis of IR, electronic, and EPR spectral studies, an octahedral geometry has been assigned for Mn(II), Co(II), and Ni(II) complexes, whereas a tetragonal geometry for the Cu(II) complexes is presumed. The free ligand and its metal complexes were tested against the phytopathogenic fungi (i.e., Rhizoctonia baticola, Alternaria alternata) in vitro.     

Ion-Exchange Separtion and Determination of Mn,Co, Zn and Ni with Xylenol Orange as Post-Column Reagent

ABSTRACT

A method for the simultaneous determination of Mn, Co, Zn and Ni which combines Ion-chromatography and a post column reaction with xylenol orange is described. Using 0.07 M oxalic acid (pH adjusted to 5.5 with lithium hydroxide) as eluent, Mn, Co, Zn and Ni were first separated on a 4x250mm IonpacCS-5 column having both sulphonic acid and Alkyl quaternary ammonia functional groups and then transferred to a post-column reaction coil, where the elements react with xylenol orange. The coloured complexes formed were spectrophotometrically measured at 570 nm. The procedure has been successfully applied for the determination of Co, Zn and Ni in Al-bronze.     

合成温度对全梯度正极材料LiNi0.7Co0.15O2的结构和电化学性能影响

通过控制结晶法和浓度梯度进料的方式制备了Ni、Co和Mn三元素组分含量呈全梯度分布的类球形Ni_0.7Co_0.15Mn_0.15（OH）₂前驱体,与LiOH·H₂O均匀混合并焙烧后获得LiNi_0.7Co_0.15O₂正极材料,系统研究了不同焙烧温度对材料Ni、Co和Mn三元素扩散情况、晶体结构及电化学性能的影响规律。通过能谱仪（EDXS）分析不同焙烧温度下材料颗粒中Ni、Co、Mn三元素的扩散程度。研究结果表明,在800℃下焙烧得到的正极材料梯度分布特征明显且电化学性能最佳,首次放电比容量为186.1 mAh·g^-1（2.8~4.3 V,0.2C）,2C大倍率充放电条件下循环200次后容量保持率为90.1%。这种材料兼具高比容量及良好的循环稳定性,可以用作下一代高能量密度锂离子电池正极材料。     

Synthesis, molecular and electronic structures of six-coordinate transition metal (Mn, Fe, Co, Ni, Cu, and Zn) complexes with redox-active 9-hydroxyphenoxazin-1-one ligands

A series of pseudo-octahedral metal (M = Mn, Fe, Co, Ni, Cu, Zn) complexes 4 of a new redox-active ligand, 2,4,6,8-tetra(tert-butyl)-9-hydroxyphenoxazin-1-one 3, have been synthesized, and their molecular structures determined with help of X-ray crystallography. The effective magnetic moments of complexes 4 (M = Mn, Fe, Co, and Ni) measured in the solid state and toluene solution point to the stabilization of their high-spin electronic ground states. Detailed information on the electronic structure of the complexes and their redox-isomeric forms has been obtained using density functional theory (DFT) B3LYP*/6-311++G(d,p) calculations. The energy disfavored low-spin structures of manganese, iron, and cobalt complexes have been located, and based on the computed geometries and distribution of spin densities identified as Mn(IV)[(Cat-N-SQ)](2), Fe(II)[Cat-N-BQ)](2), and Co(II)[Cat-N-BQ)](2) compounds, respectively. It has been shown that stabilization of the high-spin structures of complexes 4 (M = Mn, Fe, Co) is caused by the rigidity of the molecular framework of ligands 3 that sterically inhibits interconversions between the redox-isomeric forms of the complexes. The calculations performed on complex 4 (M = Co) predict that a suitable structural modification that might provide for stabilization of the low-spin electromeric forms and create conditions for the valence tautomeric rearrangement via stabilization of the low-spin electromer and narrowing energy gap between the low-spin ground state tautomer and the minimal energy crossing point on the intersection of the potential energy surfaces of the interconverting structures consists in the replacement of an oxygen in the oxazine ring by a bulkier sulfur atom.     

Formate--the analogue of azide: structural and magnetic properties of M(HCOO)2(4,4'-bpy).nH2O (M = Mn, Co, Ni; n = 0, 5)

Reaction of transition metal formate M(HCOO)(2).2H2O (M = Mn, Co, Ni) with 4,4'-bpy (4,4-bipyridine) has led to four new compounds with the formula M(HCOO)2(4,4'-bpy).nH2O (M = Mn, Co (1.Mn, 2.Co), n = 0; M = Co, Ni (3.Co, 4.Ni), n = 5). Compounds 1.Mn and 2.Co are isomorphous and crystallized in the tetragonal crystal system with the chiral space group P4(1)2(1)2. They are of three-dimensional diamondoid structure connected by anti-anti formate with 4,4'-bpy in the cavities of the framework reinforcing the intermetallic connections; the diamond-like net was observed also in their azide analogue (Mn(N3)2(4,4'-bpy)). Compounds 3.Co and 4.Ni are isomorphous also but crystallized in the monoclinic crystal system with the space group Cc. Both structures are uninterpenetrated 3D "CdSO4" type with big channels, constructed by anti-anti formate and 4,4'-bpy. This type of net was not observed in their azide analogue. Residing in the channels, water molecules form a new type of 1D tape constructed by vertex-sharing cyclic pentamers. Magnetic measurements were performed on all of these four compounds. 1.Mn and 2.Co are weak ferromagnets with the critical temperature Tc = 5.3 and 7.4 K, respectively. 3.Co is an antiferromagnet with Neel temperature TN = 3.0 K, and 4.Ni is a weak ferromagnet below 20 K. Hysteresis loop can be observed for 2.Co and 4.Ni at 1.8 K. As an analogue of azide, formate can be used to construct molecular architectures, which structurally and magnetically have great similarities to and also differences from those of azide. This offers a promising method for the design of new molecular architectures with formate.     

Second derivative spectrophotometric method for simultaneous determination of cobalt, nickel and iron using 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol

A simple, sensitive and rapid derivative spectrophotometric method using 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP) has been developed for simultaneous determination of Co(II), Ni(II) and Fe(II) which have very similar chemical behavior and appear together in many real samples. The complexes of all these metal ions with 5-Br-PADAP were formed immediately at pH 7.0 ammonium acetate buffered solution and were stable for at least 24 h. Second derivative spectra were selected for evaluation, because working wavelength determination was more precise and spectral overlap was less than in the ordinary and first derivative spectra. Three wavelengths at which the complexes exhibit extremum ²D values for Co(II), Ni(II) and Fe(II) were selected as analytical wavelengths, i.e., 640, 600 and 740 nm, respectively. Calibration curves drawn with zero-to-peak values at mentioned wavelengths were linear between 80 and 2000 ng ml⁻¹ for each metal ion. Concentrations of Co(II) and Ni(II) were calculated from the total ²D values and the sum of the linear equations for these three cations at 640 and 600 nm, after Fe(II) assay by making use of the ²D value at 740 nm. Limits of detection (LOD) for Co(II), Ni(II) and Fe(II) were 2.7, 13.9 and 3.0 ng ml⁻¹, respectively. The method has been applied to tool steel and heater resistance wire samples successfully.     

A family of cyanide-bridged molecular squares: structural and magnetic properties of [{MIICl2}2{CoII(triphos)(CN)2}2].xCH2Cl2, M = Mn, Fe, Co, Ni, Zn

The syntheses, structures, and magnetic properties of a series of tetranuclear cyanide-bridged compounds are reported. This family of molecular squares, [{M(II)Cl2}2{Co(II)(triphos)(CN)2}2] (M = Mn ([CoMn]), Fe ([CoFe]), Co ([CoCo]), Ni ([CoNi]), and Zn ([CoZn]), triphos = 1,1,1-tris(diphenylphosphinomethyl)ethane), has been synthesized by the reaction of Co(II)(triphos)(CN)2 and MCl2 (M = Mn, Co, Ni, Zn) or Fe4Cl8(THF)6 in a CH2Cl2/EtOH mixture. These complexes are isostructural and consist of two pentacoordinate Co(II) and two tetrahedral M(II) centers. The resulting molecular squares are characterized by antiferromagnetic coupling between metal centers that generally follows the spin-coupling model S total = SM(II)1 - SCo1 + SM(II)2 - SCo2. Magnetic parameters for all the complexes were measured using SQUID magnetometry. Additionally, [CoZn] and [CoMn] were studied by both conventional and high-frequency and high-field electron paramagnetic resonance.     

Effect of transition metals (Cr, Mn, Fe, Co, Ni and Cu) on selective hydrogenation of cinnamaldehyde over Pt/CNTs catalyst

Summary The effect of transition metals (Cr, Mn, Fe, Co, Ni and Cu) on the selective hydrogenation of cinnamaldehyde (CMA) to the corresponding semi-hydrogenated product over Pt/CNTs catalyst has been studied in ethanol at 343 K under 2.0 MPa H₂ pressure. PtNi/CNTs catalyst shows good catalytic activity and selectivity of C=C bond hydrogenation, 68.4% for conversion of CMA and 97.0% for selectivity of hydrocinnamaldehyde (HCMA). PtCo/CNTs catalyst shows good catalytic activity and selectivity of C=O bond hydrogenation, 91.3% for conversion of CMA and 88.2% for selectivity of cinnamylalcohol (CMO).     

First-row transition-metal complexes of a new pentadentate ligand, alpha,alpha,alpha',alpha'-tetra(pyrazolyl)lutidine

A new pentadentate ligand, alpha,alpha,alpha',alpha'-tetra(pyrazolyl)lutidine, pz 4lut, has been prepared by a CoCl 2-catalyzed rearrangement reaction between 2,6-pyridinedicarboxaldehyde and dipyrazolylthione. The coordination chemistry with some divalent first-row transition metal (Mn, Fe, Co, Ni, Cu, and Zn) chlorides has been explored. The electronic properties indicate that the new kappa (5)N ligand is a slightly stronger-field donor to Ni (2+) and Co (2+) than a related pentadentate ligand with five pyridyl donors presumably because of greater interaction between the metal and axial pyridyl.     

Comparative Study on the Structure and Electrochemical Properties of RE(Ni,Co,Mn,Ti)5 (RE=La,Ce,Pr,d) Alloys

As main composition of mishmetals, the four pure light lanthanide elements La, Ce,Pr or Nd was used individually instead of Ml or Mm as RE in preparation of AB₅ typed hydrogen storage alloy RE(Ni,Co,Mn,Ti)₅. The four alloys, La(Ni,Co₅Mn,Ti)₅, Ce(Ni,Co>ln,Ti)₅, Pr(Ni,Co,Mn,Ti)₅ and Nd(Ni,Co,Mn,Ti)₅ were then tested, characterized and compared in the their cell volumes (V_cell), P-C-T curves, and mainly electrochemical characteristics against charge/discharge cycles, including the activation cycle number (n_a),the maximum discharge opacity at 50 mA/g charge/discharge rate (C_50,max), the high-rate-dischargeability and the rate of decay (-dC/dn). These properties are compared and analyzed to reveal the difference of the effects of each element on the electrochemical properties of rare earth based AB₅ typed hydrogen storage alloy.