Effect of dissolved gases on sonochemical oxidation in a 20 kHz probe system: Continuous monitoring of dissolved oxygen concentration and sonochemical oxidation activity

Dissolved gases have a substantial influence on acoustic cavitation and sonochemical oxidation reactions. Little research on the changes in dissolved gases and the resultant changes in sonochemical oxidation has been reported, and most studies have focused only on the initial dissolved gas conditions. In this study, the dissolved oxygen (DO) concentration was measured continuously during ultrasonic irradiation using an optical sensor in different gas modes (saturation/open, saturation/closed, and sparging/closed modes). Simultaneously, the resulting changes in sonochemical oxidation were quantified using KI dosimetry. In the saturation/open mode using five gas conditions of Ar and O₂, the DO concentration decreased rapidly when O₂ was present because of active gas exchange with the atmosphere, and the DO concentration increased when 100% Ar was used. As a result, the order of the zero-order reaction constant for the first 10 min (k_0-10) decreased in the order Ar:O₂ (75:25) > 100% Ar ≈ Ar:O₂ (50:50) > Ar:O₂ (25:75) > 100% O₂, whereas that during the last 10 min (k_20-30) when the DO concentration was relatively stable, decreased in the order 100% Ar > Ar:O₂ (75:25) > Ar:O₂ (50:50) ≈ Ar:O₂ (20:75) > 100% O₂. In the saturation/closed mode, the DO concentration decreased to approximately 70–80% of the initial level because of ultrasonic degassing, and there was no influence of gases other than Ar and O₂. Consequently, k_0-10 and k_20-30 decreased in the order Ar:O₂ (75:25) > Ar:O₂ (50:50) > Ar:O₂ (25:75) > 100% Ar > 100% O₂. In the sparging/closed mode, the DO concentration was maintained at approximately 90% of the initial level because of the more active gas adsorption induced by gas sparging, and the values of k_0-10 and k_20-30 were almost the same as those in the saturation/closed mode. In the saturation/open and sparging/closed modes, the Ar:O₂ (75:25) condition was most favorable for enhancing sonochemical oxidation. However, a comparison of k_0-10 and k_20-30 indicated that there would be an optimal dissolved gas condition that was different from the initial gas condition. In addition, the mass-transfer and ultrasonic-degassing coefficients were calculated using changes in the DO concentration in the three modes.     

Effects of gas saturation and sparging on sonochemical oxidation activity in open and closed systems,part II: NO2−/NO3− generation and a brief critical review

The sonochemical generation of NO₂⁻ and NO₃⁻ is considered to be one of the reasons for the low sonochemical oxidation activity in the presence of N₂ in the liquid phase. In this study, the generation characteristics of NO₂⁻ and NO₃⁻ were investigated using the same 28 kHz sonoreactor and the 12 gas conditions used in Part I of this study. Three gas modes, saturation/closed, saturation/open, and sparging/closed, were applied. N₂:Ar (25:75), N₂:Ar (50:50), and O₂:N₂ (25:75) in the saturation/closed mode generated the three highest values of NO₂⁻ and NO₃⁻. Ar and O₂ were vital for generating relatively large concentrations of NO₂⁻ and NO₃⁻. The absorption of N₂ from the air resulted in high generation of NO₂⁻ and NO₃⁻ for Ar 100 % and Ar/O₂ mixtures under the saturation/open mode. In addition, gas sparging enhanced the generation of NO₂⁻ and NO₃⁻ for N₂:Ar (25:75), O₂:N₂ (25:75), and N₂ significantly because of the change in the sonochemically active zone and the increase in the mixing intensity in the liquid phase, as discussed in Part I. The ratio of NO₃⁻ to NO₂⁻ was calculated using their final concentrations, and a ratio higher than 1 was obtained for the condition of Ar 100 %, Ar/O₂ mixtures, and O₂ 100 %, wherein a relatively high oxidation activity was detected. From a summary of the results and findings of previous studies, it was revealed that the observations of NO₂⁻ + NO₃⁻ could be more appropriate for investigating the NO₂⁻ and NO₃⁻ generation characteristics. In addition, H₂O₂/NO₂⁻/NO₃⁻ related activity rather than H₂O₂ activity was suggested to quantify the OH radical activity more appropriately in the presence of N₂.     

Effects of gas sparging and mechanical mixing on sonochemical oxidation activity

The effects of air sparging (0–16 L min⁻¹) and mechanical mixing (0–400 rpm) on enhancing the sonochemical degradation of rhodamine B (RhB) was investigated using a 28 kHz sonoreactor. The degradation of RhB followed pseudo first-order kinetics, where sparging or mixing induced a large sonochemical enhancement. The kinetic constant varied in three stages (gradually increased → increased exponentially → decreased slightly) as the rate of sparging or mixing increased, where the stages were similar for both processes. The highest sonochemical activity was obtained with sparging at 8 L min⁻¹ or mixing at 200 rpm, where the standing wave field was significantly deformed by sparging and mixing, respectively. The cavitational oxidation activity was concentrated at the bottom of the sonicator when higher sparging or mixing rates were employed. Therefore, the large enhancement in the sonochemical oxidation was attributed mainly to the direct disturbance of the ultrasound transmission and the resulting change in the cavitation-active zone in this study. The effect of the position of air sparging and mixing was investigated. The indirect inhibition of the ultrasound transmission resulted in less enhancement of the sonochemical activity. Moreover, the effect of various sparging gases including air, N₂, O₂, Ar, CO₂, and an Ar/O₂ (8:2) mixture was compared, where all gases except CO₂ induced an enhancement in the sonochemical activity, irrespective of the concentration of dissolved oxygen. The highest activity was obtained with the Ar/O₂ (8:2) mixture. Therefore, it was revealed that the sonochemical oxidation activity could be further enhanced by applying gas sparging using the optimal gas.     

Sonochemical dissolution of nanoscale ThO2 and partial conversion into a thorium peroxo sulfate

The influence of the sample morphology and experimental conditions towards the sonochemical dissolution of nanoscale ThO₂ samples in sulfuric acid media is described. Significant sonochemical dissolution rates and yields are observed at 20 kHz under Ar/O₂ atmosphere in dilute 0.5 M H₂SO₄ at room temperature, contrasting with the generally-reported high refractory behavior for ThO₂. The dissolution of ThO₂ combines the physical effects driven by acoustic cavitation phenomenon, the complexing affinity of Th(IV) in sulfuric medium and the sonochemical generation of H₂O₂. These sonochemical conditions further allow the observation of the partial conversion of ThO₂ into a scarce Th(IV) peroxo sulfate with 1D morphology resulting from one or both following processes: dissolution/reprecipitation or formation of an intermediate Th(IV) surface complex.     

How do dissolved gases affect the sonochemical process of hydrogen production? An overview of thermodynamic and mechanistic effects – On the “hot spot theory”

Although most of researchers agree on the elementary reactions behind the sonolytic formation of molecular hydrogen (H₂) from water, namely the radical attack of H₂O and H₂O₂ and the free radicals recombination, several recent papers ignore the intervention of the dissolved gas molecules in the kinetic pathways of free radicals, and hence may wrongly assess the effect of dissolved gases on the sonochemical production of hydrogen. One may fairly ask to which extent is it acceptable to ignore the role of the dissolved gas and its eventual decomposition inside the acoustic cavitation bubble? The present opinion paper discusses numerically the ways in which the nature of dissolved gas, i.e., N₂, O₂, Ar and air, may influence the kinetics of sonochemical hydrogen formation. The model evaluates the extent of direct physical effects, i.e., dynamics of bubble oscillation and collapse events if any, against indirect chemical effects, i.e., the chemical reactions of free radicals formation and consequently hydrogen emergence, it demonstrates the improvement in the sonochemical hydrogen production under argon and sheds light on several misinterpretations reported in earlier works, due to wrong assumptions mainly related to initial conditions. The paper also highlights the role of dissolved gases in the nature of created cavitation and hence the eventual bubble population phenomena that may prevent the achievement of the sonochemical activity. This is particularly demonstrated experimentally using a 20 kHz Sinaptec transducer and a Photron SA 5 high speed camera, in the case of CO₂-saturated water where degassing bubbles are formed instead of transient cavitation.     

Sonochemical water splitting in the presence of powdered metal oxides

Kinetics of hydrogen formation was explored as a new chemical dosimeter allowing probing the sonochemical activity of argon-saturated water in the presence of micro- and nano-sized metal oxide particles exhibiting catalytic properties (ThO₂, ZrO₂, and TiO₂). It was shown that the conventional sonochemical dosimeter based on H₂O₂ formation is hardly applicable in such systems due to catalytic degradation of H₂O₂ at oxide surface. The study of H₂ generation revealed that at low-frequency ultrasound (20 kHz) the sonochemical water splitting is greatly improved for all studied metal oxides. The highest efficiency is observed for relatively large micrometric particles of ThO₂ which is assigned to ultrasonically-driven particle fragmentation accompanied by mechanochemical water molecule splitting. The nanosized metal oxides do not exhibit particle size reduction under ultrasonic treatment but nevertheless yield higher quantities of H₂. The enhancement of sonochemical water splitting in this case is most probably resulting from better bubble nucleation in heterogeneous systems. At high-frequency ultrasound (362 kHz), the effect of metal oxide particles results in a combination of nucleation and ultrasound attenuation. In contrast to 20 kHz, micrometric particles slowdown the sonolysis of water at 362 kHz due to stronger attenuation of ultrasonic waves while smaller particles show a relatively weak and various directional effects.     

Effects of Na2SO4 or NaCl on sonochemical degradation of phenolic compounds in an aqueous solution under Ar: Positive and negative effects induced by the presence of salts

Sonochemical degradation of 4-chlorophenol, phenol, catechol and resorcinol was studied under Ar at 200 kHz in the absence and presence of Na₂SO₄ or NaCl. The rates of sonochemical degradation in the absence of salts decreased in the order 4-chlorophenol > phenol > catechol > resorcinol and this order was in good agreement with the order of log P (partition coefficient) value of each phenolic compound. The effects of salts on the rates of sonochemical degradation consisted of no effect or slight negative or positive effects. We discussed these unclear results based on two viewpoints: one was based on the changes in pseudo hydrophobicity and/or diffusion behavior of phenolic compounds and the other was based on the changes in solubility of Ar gas. The measured log P value of each phenolic compound slightly increased with increasing salt concentration. In addition, the dynamic surface tension for 4-chlorophenol aqueous solution in the absence and presence of Na₂SO₄ or NaCl suggested that phenolic compounds more easily accumulated at the interface region of bubbles at higher salt concentration. These results indicated that the rates of sonochemical degradation should be enhanced by the addition of salts. On the other hand, the calculated Ar gas solubility was confirmed to decrease with increasing salt concentration. The yield of H₂O₂ formed in the presence of Na₂SO₄ or NaCl decreased with increasing salt concentration. These results suggested that sonochemical efficiency decreased with decreasing gas amount in aqueous solution: a negative effect of salts was observed. Because negative and positive effects were induced simultaneously, we concluded that the effects of salts on the rates of sonochemical degradation of phenolic compounds became unclear. The products formed from sonochemical degradation of 4-chlorophenol were also characterized by HPLC analysis. The formation of phenol and 4-chloro-1,3-dihydroxy benzene was confirmed and these concentrations were affected by the presence of salts.     

The effects of hydrogen peroxide on the sonochemical degradation of phenol and bisphenol A

This report describes the effects of H₂O₂ concentration (0.01, 0.1, 1, and 10 mM) on the sonochemical degradation of phenol and bisphenol A (BPA) using an ultrasonic source of 35 kHz and 0.08 W/mL. The concentration of the target pollutants (phenol or BPA), total organic carbon (TOC), and H₂O₂ were monitored for each input concentration of H₂O₂. The effects of H₂O₂ on the sonochemical degradation of phenol was more significant than that of BPA because phenol has a high solubility and low octanol–water partition coefficient (K_ow) value and is subsequently very likely to remain in the aqueous phase, giving it a greater probability of reacting with H₂O₂. The removal of TOC was also enhanced by the addition of H₂O₂. Some intermediates of BPA have a high K_ow value and subsequently have a greater probability of pyrolyzing by the high temperatures and pressures inside of cavitation bubbles. Thus the removal efficiency of TOC in BPA was higher than that of phenol. The removal efficiencies of TOC were lower than the degradation efficiencies of phenol and BPA. This result is due to the fact that some intermediates cannot readily degrade during the sonochemical reaction. The H₂O₂ concentration decreased but was not completely consumed during the sonochemical degradation of pollutants. The initial H₂O₂ concentration and the physical/chemical characteristics of pollutants were considered to be important factors in determining the formation rate of the H₂O₂. When high concentration of H₂O₂ was added to the solution, the formation rates were relatively low compared to when low concentrations of H₂O₂ were used.     

Degradation of Acid Blue 25 in aqueous media using 1700 kHz ultrasonic irradiation: ultrasound/Fe(II) and ultrasound/H2O2 combinations

In this work, the sonolytic degradation of an anthraquinonic dye, C.I. Acid Blue 25 (AB25), in aqueous phase using high frequency ultrasound waves (1700 kHz) for an acoustic power of 14 W was investigated. The sonochemical efficiency of the reactor was evaluated by potassium iodide dosimeter, Fricke reaction and hydrogen peroxide production yield. The three investigated methods clearly show the production of oxidizing species during sonication and well reflect the sonochemical effects of high frequency ultrasonic irradiation. The effect of operational conditions such as the initial AB25 concentration, solution temperature and pH on the degradation of AB25 was studied. Additionally, the influence of addition of salts on the degradation of dye was examined. The rate of AB25 degradation was dependent on initial dye concentration, pH and temperature. Addition of salts increased the degradation of dye. Experiments conducted using distilled and natural waters demonstrated that the degradation was more efficient in the natural water compared to distilled water. To increase the efficiency of AB25 degradation, experiments combining ultrasound with Fe(II) or H₂O₂ were conducted. Fe(II) induced the dissociation of ultrasonically produced hydrogen peroxide, leading to additional OH radicals which enhance the degradation of dye. The combination of ultrasound with hydrogen peroxide looks to be a promising option to increase the generation of free radicals. The concentration of hydrogen peroxide plays a crucial role in deciding the extent of enhancement obtained for the combined process. The results of the present work indicate that ultrasound/H₂O₂ and ultrasound/Fe(II) processes are efficient for the degradation of AB25 in aqueous solutions by high frequency ultrasonic irradiation.     

Hydrogen-assisted fabrication of spherical gold nanoparticles through sonochemical reduction of tetrachloride gold(III) ions in water

Spherical gold nanoparticles (AuNPs) were selectively synthesized through sonochemical reduction of tetrachloride gold(III) ions ([AuCl₄]⁻) in an aqueous solution of hydrogen tetrachloroaurate(III) tetrahydrate (HAuCl₄·4H₂O) with the aid of hydrogen (H₂) gas in the absence of any additional capping agents. On the other hand, various shaped-AuNPs such as spherical nanoparticles, triangular and hexagonal plates were formed from sonochemical reduction of [AuCl₄]⁻ in argon (Ar)-, nitrogen (N₂)- or oxygen (O₂)-purged aqueous [AuCl₄]⁻ solutions. The selective fabrication of spherical AuNPs assisted by H₂ gas is most likely attributed to the generation of hydrogen radicals (H) promoted by the reaction of H₂ introduced and hydrogen oxide radicals (OH) produced by sonolysis of water.     

Effect of dissolved gases in water on acoustic cavitation and bubble growth rate in 0.83 MHz megasonic of interest to wafer cleaning

Changes in the cavitation intensity of gases dissolved in water, including H₂, N₂, and Ar, have been established in studies of acoustic bubble growth rates under ultrasonic fields. Variations in the acoustic properties of dissolved gases in water affect the cavitation intensity at a high frequency (0.83 MHz) due to changes in the rectified diffusion and bubble coalescence rate. It has been proposed that acoustic bubble growth rates rapidly increase when water contains a gas, such as hydrogen faster single bubble growth due to rectified diffusion, and a higher rate of coalescence under Bjerknes forces. The change of acoustic bubble growth rate in rectified diffusion has an effect on the damping constant and diffusivity of gas at the acoustic bubble and liquid interface. It has been suggested that the coalescence reaction of bubbles under Bjerknes forces is a reaction determined by the compressibility and density of dissolved gas in water associated with sound velocity and density in acoustic bubbles. High acoustic bubble growth rates also contribute to enhanced cavitation effects in terms of dissolved gas in water. On the other hand, when Ar gas dissolves into water under ultrasound field, cavitation behavior was reduced remarkably due to its lower acoustic bubble growth rate. It is shown that change of cavitation intensity in various dissolved gases were verified through cleaning experiments in the single type of cleaning tool such as particle removal and pattern damage based on numerically calculated acoustic bubble growth rates.     

Superior selectivity of high-frequency ultrasound toward chorine containing-pharmaceuticals elimination in urine: A comparative study with other oxidation processes through the elucidation of the degradation pathways

This work considered the sonochemical degradation (using a bath-type reactor, at 375 kHz and 106.3 W L^-1, 250 mL of sample) of three representative halogenated pharmaceuticals (cloxacillin, diclofenac, and losartan) in urine matrices. The action route of the process was initially established. Then, the selectivity of the sonochemical system, to degrade the target pharmaceuticals in simulated fresh urine was compared with electrochemical oxidation (using a BDD anode, at 1.88 mA cm⁻²), and UVC/H₂O₂ (at 60 W of light and 500 mol L^-1 of H₂O₂). Also, the treatment of cloxacillin in an actual urine sample by ultrasound and UVC/H₂O₂ was evaluated. More than 90% of the target compounds concentration, in the simulated matrix, was removed after 60 min of sonication. However, the sono-treatment of cloxacillin in the real sample was less efficient than in the synthetic urine. The ultrasonic process achieved 43% of degradation after 90 min of treatment in the actual matrix. In the sonochemical system, hydroxyl radicals in the interfacial zone were the main degrading agents. Meanwhile, in the electrochemical process, electrogenerated HOCl was responsible for the elimination of pharmaceuticals. In turn, in UVC/H₂O₂ both direct photolysis and hydroxyl radicals degraded the target pollutants. Interestingly, the degradation by ultrasound of the pharmaceuticals in synthetic fresh urine was very close to the observed in distilled water. Indeed, the sonodegradation had a higher selectivity than the other two processes. Despite the sono-treatment of cloxacillin was affected by the actual matrix components, this contrasts with the UVC/H₂O₂, which was completely inhibited in the real urine. The sonochemical process led to 100% of antimicrobial activity (AA) elimination after 75 min sonication in the synthetic urine, and ∼ 20% of AA was diminished after 90 min of treatment in the real matrix. The AA decreasing was linked to the transformations of the penicillin nucleus on cloxacillin, the region most prone to electrophilic attacks by radicals according to a density theory functional analysis. Finally, predictions of biological activity confirmed that the sono-treatment decreased the activity associated with cloxacillin, diclofenac, and losartan, highlighting the positive environmental impact of degradation of chlorinated pharmaceuticals in urine.     

Acoustic cavitation at low gas pressures in PZT-based ultrasonic systems

The generation of cavitation-free radicals through evanescent electric field and bulk-streaming was reported when micro-volumes of a liquid were subjected to 10 MHz surface acoustic waves (SAW) on a piezoelectric substrate [Rezk et al., J. Phys. Chem. Lett. 2020, 11, 4655–4661; Rezk et al., Adv. Sci. 2021, 8, 2001983]. In the current study, we have tested a similar hypothesis with PZT-based ultrasonic units (760 kHz and 2 MHz) with varying dissolved gas concentrations, by sonochemiluminescence measurement and iodide dosimetry, to correlate radical generation with dissolved gas concentrations. The dissolved gas concentration was adjusted by controlling the over-head gas pressure. Our study reveals that there is a strong correlation between sonochemical activity and dissolved gas concentration, with negligible sonochemical activity at near-vacuum conditions. We therefore conclude that radical generation is dominated by acoustic cavitation in conventional PZT-based ultrasonic reactors, regardless of the excitation frequency.     

Degradation of imidacloprid containing wastewaters using ultrasound based treatment strategies

The present work deals with application of sonochemical reactors for the treatment of imidacloprid containing wastewaters either individually or in combination with other advanced oxidation processes. Experiments have been performed using two different configurations of sonochemical reactors viz. ultrasonic horn (20 kHz frequency and rated power of 240 W) and ultrasonic bath equipped with radially vibrating horn (25 kHz frequency and 1 kW rated power). The work also investigates the effect of addition of process intensifying agents such as H₂O₂ and CuO, which can enhance the production of free radicals in the system. The combination studies with advanced oxidation process involve the advanced Fenton process and combination of ultrasound with UV based oxidation. The extent of degradation obtained using combination of US and H₂O₂ at optimum loading of H₂O₂ was found to be 92.7% whereas 96.5% degradation of imidacloprid was achieved using the combination of US and advanced Fenton process. The process involving the combination of US, UV and H₂O₂ was found to be the best treatment approach where complete degradation of imidacloprid was obtained with 79% TOC removal. It has been established that the use of cavitation in combination with different oxidation processes can be effectively used for the treatment of imidacloprid containing wastewater.     

CuFe2O4 magnetic heterogeneous nanocatalyst: Low power sonochemical-coprecipitation preparation and applications in synthesis of 4H-chromene-3-carbonitrile scaffolds

The paper presents the synthesis and catalytic activity of CuFe₂O₄ nanoparticles. The CuFe₂O₄ nanoparticles have been prepared by sonochemical route under low power ultrasonic irradiation (UI) and using silent stirring at room temperature only (ST) along with co-precipitation method, without using any additive/capping agent. The synthesized magnetic nanoparticles were successfully used and compared for the synthesis of 4H-chromene-3-carbonitrile derivatives. The CuFe₂O₄ nanoparticles obtained by sonochemical route exhibit higher catalytic activity because of small size (0.5–5 nm), high surface area (214.55 m²/g), high thermal stability up to 700 °C, recyclability and reusability due to its magnetic characteristics than CuFe₂O₄ nanoparticles obtained by room temperature silent stirring. The synthesized CuFe₂O₄ nanoparticles were characterized by FT-IR, SEM–EDX, HR-TEM, XRD, TGA/DTA/DTG, BET, VSM techniques. The present method is of great interest due to its salient features such as environmentally compatible, efficient, short reaction time, chemoselectivity, high yield, cheap, moisture insensitive, green and recyclable catalyst which make it sustainable protocol.     

Preparation of magnesium ferrite nanoparticles by ultrasonic wave-assisted aqueous solution ball milling

Magnesium ferrite, MgFe₂O₄ nanoparticles with high saturation magnetization were successfully synthesized using ultrasonic wave-assisted ball milling. In this study, the raw materials were 4MgCO₃·Mg(OH)₂·5H₂O and Fe₂O₃ powders and the grinding media was stainless steel ball. The average particle diameter of the product MgFe₂O₄ powders was 20 nm and the saturation magnetization of them reached 54.8 emu/g. The different results of aqueous solution ball milling with and without ultrasonic wave revealed that it was the coupling effect of ultrasonic wave and mechanical force that played an important role during the synthesis of MgFe₂O₄. In addition, the effect of the frequency of the ultrasonic wave on the ball milling process was investigated.     

Degradation of phenol using a combination of ultrasonic and UV irradiations at pilot scale operation

In the present work, combination of ultraviolet (UV) irradiations (using 8 W UV tube) with ultrasonic (US) irradiations (rated power 1 kW and frequency of 25 kHz) has been investigated for the degradation of phenol at pilot scale of operation. Different modes of operation viz. UV alone, US alone, UV/US, UV/TiO₂ (photocatalysis), UV/H₂O₂, UV/NaCl, UV/US/TiO₂ (sonophotocatalysis) and H₂O₂ assisted sonophotocatalysis have been investigated with an objective of maximizing the extent of phenol degradation. Effect of presence of hydrogen peroxide and sodium chloride at a concentration of 10 g/l and TiO₂ over a range of 0.5–2.5 g/l has been investigated. It has been observed that 2.0 g/l of TiO₂ is the optimum concentration, beyond which a decrease in the extent of degradation is observed. Maximum extent of degradation of phenol was 37.75% for H₂O₂ assisted photosonocatalysis at pH of 2. The present work is first of its kind to report the use of combined ultrasonic and UV irradiations at pilot scale operation and obtained results should induce some degree of certainty in proposed industrial applications of sonochemical reactors for wastewater treatment.     

Determination of N and O‐atoms and N2 (A) Metastable Molecule Densities in the Afterglows of N2‐H2, Ar‐N2‐H2 and Ar‐N2‐O2 Microwave Discharges

Early afterglows of N₂‐H₂, Ar‐N₂‐H₂ and Ar‐N₂‐O₂ flowing microwave discharges are characterized by optical emission spectroscopy. The N and O atoms and the N₂ (A) metastable molecule densities are determined by optical emission spectroscopy after calibration by NO titration for N and O‐atoms and measurements of NO and N₂ band intensities. If an uncertainty of 30% is estimated on N‐atomic density, an inaccuracy of one order of magnitude is obtained on the O and N₂ (A) densities. In N₂‐(0.05‐2.5%)H₂ and Ar‐(1‐50%)N₂‐(0.05‐2.5%) H₂ gas mixtures, the O‐atoms are coming from O₂ impurities in the discharge. Concentrations of N and O‐atoms and of N₂ (A) densities are compared to the ones obtained in Ar‐(5‐50%)N₂‐(0.2‐2.5%) O₂ gas mixtures in which a controlled amount of O₂ is added. (© 2014 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Sonochemical effectiveness factor (eUS) in the reactors for wastewater treatment by sono-Fenton oxidation: Novel considerations

A comprehensive algorithm was recently proposed for calculation of the sonochemical effectiveness factor and wastewater treatment modeling. The presented approach implies that ultrasound is an auxiliary source of free radicals in Fenton type reactions; introduction of ultrasound represents an enhancement of pollutant degradation rates. The sonochemical effectiveness factor was introduced in kinetic models as the e_US factor (Gr?i? et al., 2012 [1]). As a substantial follow-up, this study presents novel considerations. The e_US factor was modeled as a function of employed frequency, actual cavitation-related power intensity of ultrasound and a portion of the cavitationally active zone, i.e. dimensionless active volume. The effect of temperature was disregarded in the present model considerations. Cavitationally active zone in reactors was determined based on the erosion of aluminum foil, resulting in cone-shaped space arising from transducer.In the present study, sonochemical treatment of industrial wastewater containing HCOONa as organic pollutant was performed using different equipment: ultrasonic baths (UB1, UB2 and UB3), cylindrical reactor with homogenizer (HCR) and three-frequency hexagonal cell, i.e. ultrasonic pilot reactor prototype (PP). Explored frequency range was from 20 to 120 kHz. Homogeneous and heterogeneous Fenton-type sonochemical processes, US/Fe(II)(FeSO₄,aq.)/H₂O₂ and US/Fe(II)(steel-plate)/H₂O₂, respectively, applied to industrial wastewater were investigated in terms of mineralization kinetics. Newly modeled e_US factor was introduced in corresponding kinetic models and the overall model was validated. Kinetic parameters of Fenton process were treated as independent of ultrasound, since e_US factor consists of cavitation-related phenomena responsible for the mineralization rate enhancement. In average, a 21% increase of mineralization efficiency was achieved using a single frequency, while more than 70% increase can be achieved by combining 20, 68 and 120 kHz in PP.     

Ultrasonic degradation, mineralization and detoxification of diclofenac in water: Optimization of operating parameters

The 20 kHz ultrasound-induced degradation of non-steroidal, anti-inflammatory drug diclofenac (DCF) was investigated. Several operating conditions, such as power density (25–100 W/L), substrate concentration (2.5–80 mg/L), initial solution pH (3.5–11), liquid bulk temperature and the type of sparging gas (air, oxygen, argon), were tested concerning their effect on DCF degradation (as assessed measuring absorbance at 276 nm) and hydroxyl radicals generation (as assessed measuring H₂O₂ concentration). Sample mineralization (in terms of TOC and COD removal), aerobic biodegradability (as assessed by the BOD₅/COD ratio) and ecotoxicity to Daphnia magna and Artemia salina were followed too.DCF conversion is enhanced at increased applied power densities and liquid bulk temperatures, acidic conditions and in the presence of dissolved air or oxygen. The reaction rate increases with increasing DCF concentration in the range 2.5–5 mg/L but it remains constant in the range 40–80 mg/L, indicating different kinetic regimes (i.e. first and zero order, respectively). H₂O₂ production rates in pure water are higher than those in DCF solutions, implying that decomposition basically proceeds through hydroxyl radical reactions. Mineralization is a slow process as reaction by-products are more stable than DCF to total oxidation; nonetheless, they are also more readily biodegradable. Toxicity to D. magna increases during the early stages of the reaction and then decreases progressively upon degradation of reaction by-products; nevertheless, complete toxicity elimination cannot be achieved at the conditions in question. Neither the original nor the treated DCF samples are toxic to A. salina.