Induced-charge electrophoresis of uncharged dielectric spherical Janus particles

We derive the equations governing the dipolophoretic motion of an electrically inhomogeneous Janus particle composed of two hemispheres with differing permittivities. The general formulation is valid for any electric forcing, including alternating current (AC) and makes no assumptions regarding the size of the electric double layer (EDL). The solution is thus valid even for nanoparticles where the particle radius can be of the same order as the EDL thickness. Semi-analytic and numerical solutions for the linear phoretic velocity and angular rotation of a single Janus particle suspended in an infinite medium are given in the limit of uniform direct current (DC) electric forcing. It is determined that particle mobility is a function of the permittivity in each hemisphere and the contrast between them as well as the EDL length. For a particle in which both hemispheres are characterized by a finite permittivity, we discover that maximum mobility and rotation is not obtained in the Helmholtz-Smoluchowski thin EDL limit but is rather a function of the permittivity and EDL properties.     

Superfast electrophoresis of electron-type conducting particles

The features of concentration polarization caused by electric current through a unipolar conductive particle are considered. The peculiarities of the formation of an induced space charge near a particle with electron-type conductivity are analysed. It has been shown that the theoretical values of electrophoretic velocity for these particles are essentially smaller than those calculated for particles with ion-type conductivity.A new method to observe the superfast electrophoresis is developed. The electrophoretic velocity of graphite and activated carbon particles of different size (diameter, 200–500 μm) displaced in distilled water and electrolyte solutions in strong electric fields (100–500 V cm⁻¹) was measured. It is shown that, in contrast to classical electrophoresis, the electrophoretic mobility of such particles increases with the particle size and the external field strength. The experimental and theoretical results are compared. The discrepancy between theory and experiment is analysed.     

A guide to design the trajectory of active particles: From fundamentals to applications

Active particles convert external energy into motility, displaying a variety of dynamical features. Recent progress in the field has marked a shift in focus from understanding the origin and sources of active motion to controlling the dynamics and trajectory of individual microswimmers. This review explores the advancements made in a two-fold perspective—the role of particle design and that of external factors. Our main goal is to highlight the guiding principles, which determine active particle trajectory. These include, on the one hand, the role of the morphology of active particles and their assemblies in driving translation, rotation, and corresponding coupling between the two. On the other hand, the effect of environmental parameters such as the presence of physicochemical heterogeneities including interfaces, suspended obstacles, and boundaries on the modality and trajectory of active colloids. We discuss the potential of using active particles in biomedical and environmental applications through recent examples.     

Dielectrophoretic focusing of particles in a microchannel constriction using DC‐biased AC flectric fields

This paper presents a fundamental study of particle electrokinetic focusing in a single microchannel constriction. Through both experiments and simulations, we demonstrate that such dielectrophoresis‐induced particle focusing can be implemented in a much smaller magnitude of DC‐biased AC electric fields (10 kV/m in total) as compared to pure DC electric fields (up to 100 kV/m). This is attributed to the increase in the ratio of cross‐stream particle dielectrophoretic velocity to streamwise electrokinetic velocity as only the DC field component contributes to the latter. The effects of the 1 kHz frequency AC to DC electric field ratio on particle trajectories and velocity variations through the microchannel constriction are also examined, which are found to agree with the simulation results.     

Characterization of polymer-coated silica particles by microelectrophoresis

Electrophoretic mobility measurements have been used to characterize monodispersed colloidal particles of silica, silica coated with alumina (cores), of these cores incorporating a dye (pigments), and finally of pigments coated with polymers. The latter consisted of poly(divinylbenzene), of poly(vinylbenzyl chloride), and of their copolymers, synthesized directly on the core or pigment particles, with and without subsequent sulfonation.     

Synthesis,Characterization, and AC Impedance Properties of a Novel Ion‐Conducting Polymer

This paper describes the preparation and characterization of a novel ion‐conducting polymeric material ( 2 ). The backbone consists of alternating alkenylidene and sulfanylidene units with adjacent hydroxy groups. Fitting of the experimental impedance data of 2 in a Bode plot reveals a conductivity of 6.6 × 10⁻² S · cm⁻¹ and a capacitance of 2.2 × 10⁻⁵ F at room temperature. The deuterated derivative of 2 shows significantly lower conductivity, suggesting that the conductivity of 2 can be attributed to proton migration.

Bode plot of fresh 2 ; experimental vs simulated; equivalent circuit (R(RQ)).     

载体表面性质对Cu2O/AC催化剂结构和活性的影响

采用活性炭(AC)载体浸渍醋酸铜, 然后热分解制备甲醇气相氧化羰基化合成碳酸二甲酯的无氯Cu2O/AC催化剂. 用硝酸或氨水处理活性炭后, 其表面的化学性质发生了变化, 从而影响了Cu2O/AC催化剂的结构和催化活性. 实验结果表明, 硝酸或氨水改性后的活性炭表面不仅有新的含氮基团产生, 而且含氧基团C-O-C, C-O和CO-O增加, CO基团明显减少或消失. 其中, 含氮基团的供电子效应和富余的CO-O基团使负载在载体上的CuⅡ更容易被还原成CuⅠ, 有利于获得组分单一且分散较好的Cu2O负载型催化剂, 从而显著地提高了催化活性. 氨水改性的活性炭更加有利于活性物种Cu2O的分散, 能够进一步改善催化性能, 在n(CO)∶n(MeOH)∶n(O2)=4∶10∶1, SV=5600 h-1条件下, 甲醇转化率达到7.0%, DMC的时空收率为145.1 mg/(g·h), 基于甲醇的选择性为68.7%.     

Dielectrophoretic investigation of plant virus particles: Cow Pea Mosaic Virus and Tobacco Mosaic Virus

This paper reports experimental results on the dielectrophoretic (DEP) behaviour on two nonenveloped plant viruses of different geometrical shapes, namely Cow Pea Mosaic Virus (CPMV) and Tobacco Mosaic Virus (TMV). The DEP properties of carboxy-modified latex beads of the same size are also reported. The DEP properties of single particles were obtained from measurement of the frequency at which the DEP force on a particle goes to zero (the crossover frequency). The DEP behaviour of particle ensembles was also measured using image processing. The dielectric properties of the particles were evaluated from the DEP data. The surface conductance was found to be 0.3 nS for CPMV, 0.38 nS for TMV, and 0.52 nS for 27 nm diameter carboxy-latex beads. Data analysis has shown that the optimal condition for separation of TMV and CPMV is a low-conductivity suspending medium - below 1 mS/m.     

Electrophoretic ratcheting of spherical particles in well/channel microfluidic devices: Making particles move against the net field

We examine the electrophoresis of spherical particles in microfluidic devices made of alternating wells and narrow channels, including a system previously used to separate DNA molecules. Our computer simulations predict that such systems can be used to separate spherical particles of different sizes that share the same free-solution mobility. Interestingly, the electrophoretic velocity shows an inversion as the field intensity is increased: while small particles have higher velocities at low field, the situation is reversed at high fields with the larger particles then moving faster. The resulting nonlinearity suggests that asymmetric pulsed electric fields could be used to build separation ratchets: particles then have a net size-dependent velocity in the presence of a zero-mean external field. Exploiting the inversion mentioned above, we show how to design pulsed field sequences that make particles move against the mean field (an example of negative mobility). Finally, we demonstrate that it is possible to use pulsed fields to make particles of different sizes move in opposite directions, even though their charge have the same sign.     

凝胶中荧光颗粒原位电泳洗脱过量异硫氰酸荧光素用于图像分析北大核心CSCD

去除荧光标记后残余荧光染料可以提高荧光颗粒检测的灵敏度、准确度和效率。该文发展了一种原位电泳洗脱(electrophoretic elution,EE)模型,用于在荧光标记后快速去除多余的荧光探针,实现荧光颗粒的灵敏检测。将牛血清蛋白(BSA)和磁珠(MBs)作为模式蛋白和微颗粒,混合孵育获得MBs-BSA,用异硫氰酸荧光素(FITC)对MBs-BSA标记,得到MBs-BSA_(FITC)复合物。将含有多余FITC的MBs-BSA_(FITC)溶液与低凝聚温度琼脂糖凝胶溶液按1∶5的体积比混合,并将混合物凝胶和纯琼脂糖凝胶分段填充到电泳通道中。电泳过程中,利用颗粒尺寸与凝胶孔径的差异来保留MBs-BSA_(FITC),同时将游离的FITC洗脱。经过30 min的电泳洗脱,通道内多余的FITC清除率达到97.6%,同时目标颗粒荧光信号保留了27.8%。成像系统曝光时间为1.35 s时,电泳洗脱将颗粒与背景的荧光信号比(P/B ratio,PBr)从1.08增加到12.2。CCD相机的曝光时间增加到2.35 s,可以将PBr提高到15.5,可进一步实现对微弱荧光亮点的高灵敏检测。该模型有以下优点:(1)能对颗粒表面非特异性吸附的FITC实现有效洗脱,提高了检测的特异性;(2)能够将97%以上的游离FITC清除;(3)30 min内能够使凝胶内的背景荧光大幅降低,提高了PBr和检测灵敏度。因此,该方法具有在凝胶中进行基于磁珠/荧光颗粒点的免疫检测、在免疫电泳或凝胶电泳中对蛋白质/核酸条带进行荧光染色等领域的应用潜力。     

A novel particle separation method based on induced‐charge electro‐osmotic flow and polarizability of dielectric particles

A new microfluidic method of particle separation was proposed and studied theoretically in this paper. This method is based on the induced charge electro‐osmotic flow (ICEOF) and polarizability of dielectric particles. In this method, a pair of metal plates is embedded on the side channel walls to create a region of circulating flows under applied electric field. When a dielectric particle enters this region, the vortices produced by ICEOF around the particle will interact with the circulating flows produced by the metal plates. Such hydrodynamic interaction influences the particle's trajectory, and may result in the particle being trapped in the flow circulating zone or passing through this flow circulating zone. Because the hydrodynamic interaction is sensitive to the applied electric field, and the polarizability and the size of the particles, separation of different particles can be realized by controlling these parameters. Comparing with electrophoresis and dielectrophoresis methods, this strategy presented in this paper is simple and sensitive.     

Polymer modification of colloidal particles by spontaneous polymerization of surface active monomers

Adsorption and spontaneous polymerization of head- or tail-type surface active monomers having long methylene chains on colloidal silica and δ-alumina were investigated. Both head-type and tail-type ammonium monomers on silica in chloroform or tetrahydrofuran had the maximum adsorption on the respective adsorption isotherm. Above the monomer concentration giving the maximum adsorption, it was observed that the monomer formed micelles or clusters in bulk solution with removal of adsorbed water molecules from the silica surface. At the monomer concentration giving the maximum adsorption, heating the silica suspension containing the monomer at 40°C or 60°C in tetrahydrofuran or chloroform solution resulted in spontaneous polymerization. The composite particles formed by polymerization were observed to have many spots consisting of polymer on the surface. Therefore, it is suggested that the monomers are concentrated by micelle-like aggregation on the silica surface and consecutively spontaneous polymerization takes place. Adsorption of an anion-type monomer having a carboxyl group on δ-alumina, which exhibited a positive ζ potential in neutral aqueous solution, was higher than that on colloidal silica, but did not spontaneously polymerize on alumina. Received: 13 June 1998 Accepted in revised form: 19 August 1998     

苯乙酮氢转移反应中ZrO2/MCM-41和ZrO2/AC的催化性能对比

采用浸渍法制备了分别以活性炭(AC)和全硅MCM-41介孔分子筛负载的ZrO2催化剂,并对其进行了XRD、氮气吸附-脱附、X射线光电子能谱、差热-热重分析和吡啶吸附原位红外光谱等表征,考察了其在以异丙醇为氢源还原苯乙酮为α-苯乙醇的Meerwein-Ponndorf-Verley(MPV)反应中的催化活性,并与水合ZrO2进行对比.研究了载体对催化剂活性的影响.结果表明,ZrO2经MCM-41负载后,与载体发生强相互作用,可能形成Si—O—Zr键,ZrO2在载体表面呈高分散的无定形态,Zr—OH数目显著增加,L酸性增强,并形成B酸中心,使催化剂活性显著高于水合ZrO2;ZrO2负载在AC上后,与载体未发生强相互作用,ZrO2在载体表面未呈高分散状态,增加的Zr—OH数目相对较少,L酸性较弱,未形成B酸中心,催化活性未明显增加,但在较高焙烧温度(400～600℃)下,其仍能保持稳定的催化活性,这可归因于ZrO2/AC中AC孔道疏通及AC石墨层对苯乙酮上苯环的吸附作用,使活性位附近的反应底物浓度显著增大.     

A 100-kW three-phase AC plasma furnace for spheroidization of aluminum silicate particles

A 100-kW three-phase ac plasma furnace with sheathed copper electrodes (sheathing gas: air) is presented. It is used for spheroidizing chamotte (refractory-fired clay) particles having a smooth, pore-free surface. A simple, one-dimensional numerical model for the heat transfer to the particles explains the maximum processing rate and the detrimental influence of an inhomogeneous particle size distribution.     

Simple design of an aligned transparent biofilm by magnetic particles and its cellular study

The aim of this study was to produce aligned biodegradable films. In this study, we used magnetic microparticles and strong magnetic field for orientation of gelatin gels. The samples were evaluated by microscopic analyses and cell culture assays with Schwann cells. Results of structural analyses showed a good arrangement and orientation of films under strong magnetic field with movement of magnetite particles. Cellular experiments showed a good cell adhesion and orientation on the designed films compared with those on unmodified ones. This aligned guide appears to have the right organization for testing in vivo nerve tissue engineering studies. Copyright © 2016 John Wiley & Sons, Ltd.     

Methyl methacrylate particles with amino groups on the surface: Colloid stability and sorption of biologically active substances

The present article investigates the influence of dispersion medium on the aggregate stability of cross-linked poly-(methyl methacrylate) particles on the surface layer of which aliphatic amino groups are localized. It is shown that particle size depends on the ionic strength of dispersion medium. The research determines the optimal content of cross-linked agent, ethylene glycol dimetharylate that results in the formation of cationic particles being stable in saline. Particle modification is performed by bovine serum albumin and luminophore fluorescein 5(6)-isothiocyanate. Protein sorption is observed not to influence luminescent properties of the particles. It is also determined that due to the aggregate stability of particles obtained from 5?wt% of ethylene glycol dimethacrylate in saline, the monodispersity and the absence of inversion of zeta potential in wide pH range is retained, such particles may be considered as perspective carriers of biologically active substances.     

Accumulation and trapping of hepatitis A virus particles by electrohydrodynamic flow and dielectrophoresis

Hepatitis A virus particles (d = 27 nm) were successfully accumulated and trapped in a microfluidic system by means of a combination of electrohydrodynamic flow and dielectrophoretic forces. Electric fields were generated in a field cage consisting of eight microelectrodes. In addition, high medium conductance (0.3 S/m) resulted in sufficient Joule heating and the corresponding spatial variation of temperature, density, and permittivity to induce electrohydrodynamic flow in the vicinity of the field cage. Flow vortices transport particles toward the center of the field cage, where dielectrophoretic forces cause permanent entrapment and particle aggregation. Spatial distribution of temperature, density, and permittivity as well as resulting flow patterns were modeled numerically and are in good agreement with experimental results. This accumulation scheme might be applicable to sample concentration enhancement in biosensor applications.     

Effect of a surface charge on the halfwidth and peak position of cluster plasmons in colloidal metal particles

The optical response of colloidal particles depends on a variety of properties of the cluster, e.g., shape, size, size distribution and particle material. Since particles often are charged, also the surface charge may be a parameter which influences their optical properties. In this paper the effect of a surface charge on optical properties of spherical colloidal particles is studied and its magnitude is estimated by extended computations for silver clusters with surface plasmon in aqueous suspension. Two models are presented and discussed. The first model is based on the electrodynamic solution by Bohren and Hunt (Can. J. Phys. 55, 1930 (1977)), where a surface conductivity _S for a free surface charge yield an additional contribution _S to the dielectric constant of the particle material. In the second model, the surface charge contributes to the number density of free electrons in the cluster. Both models lead to a shift of the cluster plasmon peak, while an increase of the plasmon halfwidth could not be derived. The effect is quite small and limited on very small clusters.PACS 61.46+w 73.20.Mf 78.20.Dj     

集成毛细管电泳芯片系统的制作、测试及应用

使用标准光刻和化学湿法腐蚀技术,在玻璃板材上制作了由样样管道和分离管道内构成的集成毛细管网路系统,对影响芯片质量的一些因素进行了讨论,并进行了性能测试和评价。芯片上毛细管道散热良好。使用激光诱导荧光和CCD成像检测系统,以电渗作用为驱动力,对混合样品进行了进样、快速分离（20s以内）和监测,证明了自制集成毛细管电泳芯片及检测系统的可行性。比较了两种注样方式（float和pinched)的不同;证明了在分离时可以优化加电策略,防止拖尾,改善峰形。