腐植酸钠/聚N-异丙基丙烯酰胺/粘土杂化水凝胶的合成及脱色性能

腐植酸钠;聚N-异丙基丙烯酰胺;粘土;水凝胶;亚甲基蓝     

腐植酸钠/聚丙烯酰胺/粘土杂化水凝胶的研究

以过硫酸钾为引发剂、N,N′-亚甲基双丙烯酰胺为交联剂、丙烯酰胺单体和腐植酸钠、Laponite RD粘土为原料,用溶液聚合交联法合成了腐植酸钠/聚丙烯酰胺/粘土(SH-PAM-Clay)系列水凝胶.用场发射扫描电镜对其表面形貌进行了研究,并对水凝胶的吸水性和流变性能进行了测试和研究.结果表明这系列水凝胶都具有致密的网络结构和优良的吸水性能.     

多孔聚N-异丙基丙烯酰胺水凝胶的制备与缓释性能

以N-异丙基丙烯酰胺(NIPA)、N,N-亚甲基双丙烯酰胺(MBA)和聚乙二醇(PEG)为原料,以60Co-γ射线为放射源制备了快速响应聚N-异丙基丙烯酰胺(PNIPA)多孔水凝胶。用红外光谱分析了水凝胶的结构,并测定了水凝胶的溶胀动力学、退溶胀动力学和平衡溶胀率。结果表明,PEG分子仅在聚合交联过程中充当成孔剂,不参与反应,反应后可被除去;水凝胶具有明显的温度敏感性,成孔剂的添加提高了水凝胶的溶胀性能和LCST。选用阿司匹林为模型药物,对水凝胶的药物缓释性能进行了初步研究。     

羧甲基纤维素钠/聚(N-异丙基丙烯酰胺)纳米复合水凝胶的制备及结构性能表征

以无机粘土为交联剂制备了具有温度、pH双重敏感特性的羧甲基纤维素钠/聚(N-异丙基丙烯酰胺)/粘土半互穿网络纳米复合水凝胶(CMC/PNIPA/Clay semi-IPN),并通过红外和透射电镜对其结构和形态进行了表征。在酸性(pH=1.2)和20℃条件下,分别研究了温度和不同pH缓冲液对该凝胶溶胀度的影响,测定了复合水凝胶的力学性能。结果表明:水凝胶中的粘土被剥离成单片层,且均匀分散在凝胶网络中,起交联剂的作用,而CMC以线性大分子的形态存在;CMC/PNIPA/Clay具有良好的温度、pH双重敏感特性;凝胶的断裂伸长率>1 000%。     

PNIPA和PDEA在水-甲醇混合溶剂中性质的研究

分别研究了聚N-异丙基丙烯酰胺（PNIPA）和聚N,N-二乙基丙烯酰胺（PDEA）在水-甲醇混合溶剂中的溶液性质.结果表明,在PDEA和PNIPA体系中均存在水和甲醇分子之间的复合.由于PDEA比PNIPA的亲脂性强,在水-甲醇混合溶剂中,水与甲醇分子形成的复合物对PDEA和PNIPA的溶剂化作用不同,导致随着体系中甲醇体积分数（φ）的增大,PNIPA体系的低临界溶解温度（TLCS）发生了再进入相转变,而PDEA体系的TLCS则逐渐升高.     

N-异丙基甲基丙烯酰胺共聚热缩温敏水凝胶

从甲基丙烯腈与异丙醇反应制备了N-异丙基甲基丙烯酰胺(NIPM),研究了其以N,N′-亚甲基双丙烯酰胺(MBA)为交联剂在不同溶剂体系的聚合及所形成的水凝胶的性质。表明NIPM-MBA凝胶具有热缩温敏性。在NIPM-MBA体系引入丙烯酸钠、甲基丙烯酸钠等负离子单体时,凝胶的溶胀比明显增加,MBA所占比例较少的体系,具有热缩、热胀双重性。     

聚N-异丙基丙烯酰胺/纳米SiO2复合水凝胶的合成及溶胀性能

通过纳米SiO2的表面功能化,在其表面引入乙烯基功能基团,在H2O／THF的混合溶剂中,超声分散后,交联剂N,N′-亚甲基双丙烯酰胺存在时,于25℃下使其与N-异丙基丙烯酰胺共聚,制得聚N-异丙基丙烯酰胺,纳米SiO2复合水凝胶,并用FT-IR和SEM对产物进行了表征,研究了凝胶的溶胀动力学,消溶胀动力学和温度敏感性,实验结果表明,纳米SiO2的引入,改善了聚N-异丙基丙烯酰胺水凝胶在低温时的溶胀性能和在高温时对水的释放性能,并讨论了引起这些性能改变的原因。     

N—异丙基甲基丙烯酰胺共聚热缩温敏水凝胶

从甲基丙烯腈与异丙醇反应制备了Ｎ－异丙基甲基丙烯酰胺（ＮＩＰＭ），研究了其以Ｎ，Ｎ＇－亚甲基双丙烯酰胺（ＭＢＡ）为交联剂在不同溶剂体系的聚合及所形成的水凝胶的性质。表明ＮＩＰＭ－ＭＢＡ凝胶具有热缩温敏性。在ＮＩＰＭ－ＭＢＡ体系引入丙烯酸钠、甲基丙烯酸钠等负离子单体时，凝胶的溶胀比明显增加，ＭＢＡ所占比例较少的体系，具有热缩、热胀双重性。     

动态凝胶网络中的溶质扩散

从理论和实验两方面研究了凝胶网络中溶质的扩散 .着重于凝胶网络的涨落对扩散的影响 ,以动态链渗流理论建立了凝胶动态网络中溶质扩散的数学模型 .制备了聚异丙基丙烯酰胺(PNIPA)水凝胶 ,用激光光散射法测定了凝胶网络的涨落行为 .用双室膜池法以甲基蓝为溶质测定了凝胶中的扩散 .模型与实验结果定性相符 .     

聚N-异丙基丙烯酰胺/类水滑石复合水凝胶的制备及温敏性

以类水滑石(LDHs)和N-异丙基丙烯酰胺(NIPA)为原材料,采用自由基引发聚合制得了有机无机PNIPA/LDHs温度敏感复合水凝胶。 通过热重分析仪(TGA)、示差扫描量热仪(DSC)和扫描电子显微镜(SEM)等技术手段表征了材料的结构和性能。 结果表明,PNIPA/LDHs复合水凝胶在33 ℃左右可实现溶胶-凝胶的可逆性变化,LDHs质量分数基本不影响复合水凝胶的胶凝化温度和胶凝时间。 LDHs添加可使PNIPA/LDHs复合水凝胶的热稳定性较NIPA有大幅度提升。 随LDHs质量分数及n(Mg):n(Al)的增加,复合凝胶的吸热峰值稍有增加。 所合成PNIPA/LDHs复合水凝胶表面粗糙不平,具有一定的孔洞结构。     

Studies of sodium humate/polyacrylamide/clay hybrid hydrogels. I. Swelling and rheological properties of hydrogels

A type of novel hybrid hydrogels from sodium humate (SH), polyacrylamide (PAM), and hydrophilic Laponite clay were prepared using potassium persulfate (KPS) as the initiator and N,N′-methylenebisacrylamide (MBA) as the cross-linker. The structures of the hydrogels were characterized by field emission scanning electron microscope and FTIR. Their swelling properties, swelling mechanism and rheological properties were also investigated. Experiments show that the composite is heterogeneous in the PAM/SH hydrogel system, while the clay collaborates with SH and improves the network structure of PAM/SH/clay hydrogel. High water-absorbing capability is shown for both hydrogel systems. Han plot proves that clay and SH are compatible with PAM for PAM/SH/clay hydrogels.     

Preparation and characterization of sodium carboxymethylcellulose/poly(N-isopropylacrylamide)/clay semi-IPN nanocomposite hydrogels

A new kind of pH-/temperature-responsive semi-interpenetrating polymer network hydrogels based on linear sodium carboxymethylcellulose (CMC) and poly(N-isopropylacrylamide) (PNIPA) cross-linked by inorganic clay (CMC/PNIPA/Clay hydrogel) was prepared. The temperature- and pH-responsive behaviors, the mechanical properties of these hydrogels were investigated. The CMC/PNIPA/Clay hydrogels exhibited a volume phase transition temperature around 32 °C with no significant deviation from the conventional PNIPA hydrogels. The swelling ratio of the CMC/PNIPA/Clay hydrogels gradually decreased with increasing the contents of clay. The influence of pH value on swelling behaviors showed that there is a maximum swelling ratio at pH 5.9. Moreover, the CMC/PNIPA/Clay hydrogels exhibited excellent mechanical properties with high tensile stress and elongation at break in excess of 1200%.     

A novel sodium carboxymethylcellulose/poly(N‐isopropylacrylamide)/Clay semi‐IPN nanocomposite hydrogel with improved response rate and mechanical properties

A novel semi‐IPN nanocomposite hydrogel (CMC/PNIPA/Clay hydrogel) based on linear sodium carboxymethylcellulose (CMC) and poly(N‐isopropylacrylamide) (PNIPA) crosslinked by inorganic clay was prepared. The structure and morphology of these hydrogels were investigated and their swelling and deswelling kinetics were studied in detail. TEM images showed that the clay was substantially exfoliated to form nano‐dimension platelets dispersed homogeneously in the hydrogels and acted as a multifunctional crosslinker. The CMC/PNIPA/Clay hydrogels swell faster than the corresponding PNIPA/Clay hydrogels at pH 7.4, whereas they swell slower than the PNIPA/Clay hydrogels at pH 1.2. The CMC/PNIPA/Clay nanocomposite hydrogels showed much higher deswelling rates, which was ascribed to more passway formed in these hydrogels for water to diffuse in and out. The deswelling process of the hydrogels could be approximately described by the first‐order kinetic equation and the deswelling rate decreased with increasing clay content. The mechanical properties of the CMC/PNIPA/Clay nanocomposite hydrogels were analyzed based on the theory of rubber elasticity. It was found that with increasing clay content, the effective crosslink chain density, v_e, increased whereas the molecular weight of the chains between crosslinks M_c decreased. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1546–1555, 2008     

Stimuli-responsive nanocomposite gels

A new class of polymer hydrogels, nanocomposite hydrogels (NC gels), consisting of a unique organic (polymer)/inorganic (clay) network structure, was synthesized by in situ free-radical polymerization in the presence of exfoliated clay nanoparticles in an aqueous system. The resulting NC gels overcame most of the disadvantages associated with chemically cross-linked hydrogels, such as mechanical fragility, structural heterogeneity, and slow de-swelling rate. By using thermo-sensitive poly(N-isopropylacrylamide) (PNIPA) as a constituent polymer, NC gels with remarkable mechanical, optical, and swelling properties as well as thermo-sensitivity were obtained. The various properties of NC gels, such as transparency, gel volume, cell culturing, and surface friction changed significantly in response to the temperature and surrounding conditions. All the excellent properties and new stimuli-responsive characteristics of NC gels are attributed to the unique PNIPA/clay network structure. The thermo-sensitivities and the transition temperature can largely be controlled by varying the clay content and by the addition of solutes.     

Preparation and characterization of pH- and temperature-responsive semi-IPN hydrogels of carboxymethyl chitosan with poly (<Emphasis Type="Italic">N</Emphasis>-isopropyl acrylamide) crosslinked by clay

A new kind of pH- and temperature-responsive semi-interpenetrating polymer network hydrogel based on linear carboxymethylchitosan (CMCS) and poly (N-isopropylacrylamide) (PNIPA) crosslinked by inorganic clay was prepared. The pH-and temperature-responsive behaviors, the deswelling kinetics, and the mechanical properties of the hydrogel were investigated. The hydrogels exhibited a volume phase transition temperature around 33 °C with no significant deviation from the conventional PNIPA hydrogels. The results of the influence of pH value on the swelling behaviors showed that the minimum swelling ratios of the hydrogels appeared near the isoelectric point (IEP) of CMCS, and when pH deviated from the IEP, the hydrogels behaved as polycations or polyanions. The novel hydrogels had much higher response rate than the conventional CMCS/PNIPA hydrogels. Moreover, the semi-IPN hydrogels crosslinked by clay could be elongated to more than 800% and the elongation could be recovered almost completely and instantaneously.     

Preparation and separation function of N‐isopropylacrylamide copolymer hydrogels

In this paper, N‐isopropylacrylamide (NIPA) was synthesized by acrylonitrile and isopropanol. Poly(N‐isopropylacrylamide) (PNIPA) was prepared by a chemical method. The dependence of its swelling behavior on temperature was studied. Results showed that PNIPA hydrogel was a temperature‐sensitive gel. Its LCST (lower critical solution temperature) was about 32 °C, and its swelling ratio (at 20 °C) was about 17–18. Sodium acrylate (SA) and sodium methylacrylate (SMA) were copolymerized with NIPA respectively. Equilibrium swelling ratios of the copolymer hydrogels at lower temperature were two to three times that of PNIPA. The LCST of the copolymer hydrogels could be controlled between 32 and 45 °C by adjusting the content of SA or SMA. Kinetics of P(NIPA‐co‐SA) hydrogels, whether swelling or shrinking processes, were in good agreement with apparent second order kinetic equations. Several experiments were designed to separate aqueous bovine serum albumin solution using the hydrogels prepared above. The separation efficiency was about 80%. Copyright © 2000 John Wiley & Sons, Ltd.     

Preparation and properties of superabsorbent containing starch and sodium humate

Starch and sodium humate were utilized as raw material for synthesizing starch‐g‐poly(acrylic acid)/sodium humate (St‐g‐PAA/SH) superabsorbent by graft copolymerization reaction of starch (St) and acrylic acid (AA) in the presence of sodium humate (SH) in aqueous solution. The effect of weight ratio of AA to St, initial monomer concentration, neutralization degree of AA, amount of crosslinker, initiator and SH on water absorbency of the superabsorbent were studied. The swelling rate and swelling behavior in NaCl solution as well as reswelling ability of the superabsorbent were systematically investigated. The results showed that the superabsorbent synthesized under optimal conditions with SH content of 7.7 wt% and St content of 11.5 wt% exhibits water absorbency of 1100 g/g in distilled water and 86 g/g in 0.9 wt% NaCl solution, respectively. Introducing SH into the St‐g‐PAA polymeric network can improved the swelling rate and reswelling capability of the superabsorbent. Copyright © 2008 John Wiley & Sons, Ltd.