Non-aqueous capillary electrophoresis of biological samples after at-line solid-phase extraction

Summary Solid-phase extraction (SPE) was coupled at-line to capillary electrophoresis (CE) for the determination of a series of basic test compounds (i. e. tricyclic antidepressants). The analysis was performed using a non-aqueous CE buffer, which resulted in baseline separation of all test compounds. This is in marked contrast with CE using aqueous buffers where hardly any separation was obtained either with or without micelles. The SPE procedure was used to remove simultaneously most of the water from the sample, because no direct analysis of aqueous samples is possible when a non-aqueous CE buffer is used. With the present method the antidepressants can be determined in both urine and serum. Analyte detectability is increased up to 10-fold due to trace enrichment during the extraction process; the limits of detection (LODs; UV 214 nm) are 30–300 ng mL⁻¹ in urine and 300–1000 ng mL⁻¹ in serum. TheRSD values (n=5) of the within-day and between-day precision are below 9% and 11% respectively. Therefore, the present procedure can be used for drug monitoring.     

Determination of Non-Steroidal Anti-Inflammatory Drugs in Natural Waters Using Off-Line and On-Line SPE Followed by LC Coupled with DAD-MS

Two different procedures for simultaneous determination of six NSAIDs (diflunisal, diclofenac, fenoprofen, ibuprofen, naproxen and tolmetin) in environmental waters are described. Final analysis of target compounds is performed by reversed-phase liquid chromatography – diode array detection and mass spectrometry (HPLC-DAD and LC-MS), whereas sample preparation is based on solid-phase extraction (SPE). A variety of sorbents and their respective advantages and disadvantages are discussed. For the off-line SPE of NSAIDs from water samples, a LiChrolut RP-18 was selected out of all investigated sorbents. In case of on-line coupling of SPE with chromatographic system LiChrosphere RP-18 was selected as the best one in terms of recovery of NSAIDs evaluated, RSD and availability. The applicability of the method was also evaluated. Method detection limits were in the range of 0.7−94 ng L⁻¹. Recoveries ranged from 96 to 109% and relative standard deviations were lower than 5%. The procedures were shown to be linear over a wide range of concentration, exhibited satisfactory repeatability and accuracy, and reached limits of detection in the low ng L⁻¹ range. No breakthrough volume was observed neither for off-line SPE (in the studied range of 100, 200, 300, 500, 700, 1000 and 2000 mL of tap water sample) nor for on-line SPE (in the wide range of 10 mL, 20 mL, 30 mL, 50 mL, 70 mL, 100 mL and 200 mL of tap water sample).     

Evaluation of an analytical method for determining phthalate esters in wine samples by solid-phase extraction and gas chromatography coupled with ion-trap mass spectrometer detector

A solid-phase extraction (SPE) method was developed for extraction and analysis of six phthalate esters in wine samples using Carbograph 1 sorbent. The SPE procedure allowed efficient recovery of the investigated phthalates ranging between 78% and 105% with a relative standard deviation (RSD) ≤6.5 for an ethanolic phthalic acid ester (PAE) standard solution and between 73–71% and 96–99% with a RSD ≤8.4 for red wine samples spiked with 20 and 50 ng mL⁻¹ of PAE, respectively. The adsorption isotherms and breakthrough curves for Carbograph 1/water solution were reported. Gas chromatography coupled with an ion-trap mass spectrometer detector (GC/IT-MS) was used for analysis. The instrumental analytical protocol was found to yield a linear calibration in the range 0.01-10.0 μg mL⁻¹ with R ² values ≥0.9992. The limits of detection in GC/IT-MS (SIM mode) vary between 0.2 and 14 ng mL⁻¹ (RSD ≤5.6) whereas the limits of quantification range between 0.5 and 25 ng mL⁻¹ (RSD ≤5.9); the intra- and inter-day repeatabilities calculated as RSD for wine samples, were between 0.9–7.8 and 1.0–10.5, respectively. The analytical method developed was applied to several commercial wine samples. Furthermore, the investigated methods are simple, reliable, reproducible, and not expensive.     

Simultaneous Determination of Cyanazine, Chlorotoluron and Chlorbenzuron in Environmental Water Samples with SPE Multiwalled Carbon Nanotubes and LC

In this paper, a new method based on solid-phase extraction with multiwalled carbon nanotubes as the packed materials for sensitive determination of cyanazine, chlorotoluron and chlorbenzuron in environmental water samples was demonstrated. Related parameters that may influence the enrichment efficiency of multiwalled carbon nanotubes such as the kind and volume of elute, sample flow rate, sample pH, and volume of the water samples were investigated. Under the optimum conditions, the detection limits of cyanazine, chlorbenzuron and chlorotoluron were 0.015, 0.012, 0.034 ng mL⁻¹, respectively. The experimental results indicated a good linearity (R ² > 0.9947) over the concentration range of 0.4–40 ng mL⁻¹ for cyanazine and chlorotoluron, and 0.8–80 ng mL⁻¹ for chlorbenzuron. The relative standard deviations of the three analytes were 3.54, 1.55 and 1.38%, respectively. The established method also was applied to the analysis of the real-world water samples and excellent achievements were obtained with average spiked recoveries from 87.8 to 110.1%. All the results indicated that this procedure could allow the simultaneous determination of these three compounds in environmental water samples at trace levels.     

Study of the metabolism on tobacco-specific N-nitrosamines in the rabbit by solid-phase extraction and liquid chromatography–tandem mass spectrometry

Metabolism of four tobacco-specific N-nitrosamines (TSNAs), N′-nitrosonornicotine (NNN), N′-nitrosoanatabine (NAT), N′-nitrosoanabasine (NAB), and 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanone (NNK) has been studied by solid-phase extraction (SPE) and liquid chromatography–tandem mass spectrometry (LC–MS–MS). 4-(Methylnitrosamino)-4-(3-pyridyl)-1-butanol (iso-NNAL) was used as internal standard. SPE and LC–MS–MS was found to be a rapid, simple, sensitive, and selective method for analysis of TSNAs in rabbit serum. The relative standard deviation (R.S.D., n = 6) for analysis of 5 ng mL⁻¹ and 0.5 ng mL⁻¹ standards and of serum sample spiked with 5 ng mL⁻¹ standards of five TSNAs was 2.1–11% and recovery of 5 ng mL⁻¹ standards from serum was 100.2–112.9%. A good linear relationship was obtained between peak area ratio and concentration in the range of 0.2–100 ng mL⁻¹ for NNAL and 0.5–100 ng mL⁻¹ for other four TSNAs, with correlation coefficients (R ²) >0.99 (both linear and log–log regression). Detection limits for standards in solvent were between 0.04 and 0.10 ng mL⁻¹. Doses of TSNAs administered to rabbits via the auricular vein were 4.67 μg kg⁻¹ and 11.67 μg kg⁻¹, in accordance with the different levels in cigarettes. Metabolic curves were obtained for the four TSNAs and for 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanol (NNAL), a metabolite of NNK; on the basis of these curves we modeled metabolic kinetic equations for these TSNAs by nonlinear curve fitting.     

Polar herbicides,pharmaceutical products,perfluorooctanesulfonate (PFOS), perfluorooctanoate (PFOA), and nonylphenol and its carboxylates and ethoxylates in surface and tap waters around Lake Maggiore in Northern Italy

A survey of contamination of surface and drinking waters around Lake Maggiore in Northern Italy with polar anthropogenic environmental pollutants has been conducted. The target analytes were polar herbicides, pharmaceuticals (including antibiotics), steroid estrogens, perfluorooctanesulfonate (PFOS), perfluoroalkyl carboxylates (including perfluorooctanoate PFOA), nonylphenol and its carboxylates and ethoxylates (NPEO surfactants), and triclosan, a bactericide used in personal-care products. Analysis of water samples was performed by solid-phase extraction (SPE) then liquid chromatography–triple-quadrupole (tandem) mass spectrometry (LC–MS–MS). By extraction of 1-L water samples and concentration of the extract to 100 μL, method detection limits (MDLs) as low as 0.05–0.1 ng L⁻¹ were achieved for most compounds. Lake-water samples from seven different locations in the Southern part of Lake Maggiore and eleven samples from different tributary rivers and creeks were investigated. Rain water was also analyzed to investigate atmospheric input of the contaminants. Compounds regularly detected at very low concentrations in the lake water included: caffeine (max. concentration 124 ng L⁻¹), the herbicides terbutylazine (7 ng L⁻¹), atrazine (5 ng L⁻¹), simazine (16 ng L⁻¹), diuron (11 ng L⁻¹), and atrazine-desethyl (11 ng L⁻¹), the pharmaceuticals carbamazepine (9 ng L⁻¹), sulfamethoxazole (10 ng L⁻¹), gemfibrozil (1.7 ng L⁻¹), and benzafibrate (1.2 ng L⁻¹), the surfactant metabolite nonylphenol (15 ng L⁻¹), its carboxylates (NPE₁C 120 ng L⁻¹, NPE₂C 7 ng L⁻¹, NPE₃C 15 ng L⁻¹) and ethoxylates (NPE _n Os, n = 3-17; 300 ng L⁻¹), perfluorinated surfactants (PFOS 9 ng L⁻¹, PFOA 3 ng L⁻¹), and estrone (0.4 ng L⁻¹). Levels of these compounds in drinking water produced from Lake Maggiore were almost identical with those found in the lake itself, revealing the poor performance of sand filtration and chlorination applied by the local waterworks.     

Determination of eight penicillins in serum from cattle and pigs by generic HPLC method

Summary An HPLC method was developed for determination of amoxicillin, penicillin G, penicillin V, ampicillin, oxacillin, cloxacillin, nafcillin and dicloxacillin in serum from pigs and cattle. Serum was cleaned up by solid-phase extraction (SPE), ultra-filtered and derivatised. The method was linear in the range tested up to 2000 ng mL⁻¹ of individual penicillins in serum. Limits of detection were 11–14 ng mL⁻¹. Mean recoveries were 90–103% in the range 20–2000 ng mL⁻¹. The relative repeatability, standard deviation was <10% at 20 ng mL⁻¹ level and <6% in the range 100–2000 ng mL⁻¹.     

Determination of tebufenpyrad and oxadiazon by solid-phase microextraction and gas chromatography-mass spectrometry

Summary A method for determination of trace amounts of the pesticides tebufenpyrad and oxadiazon, previous solid-phase microextraction (SPME), was developed using gas chromatographymass spectrometry and selected ion monitoring (GC-MS; SIM). Both pesticides were extracted with a fused silica fiber coated with 100 μm polydimethylsiloxane. The effects of pH ionic strength, sample volume, extraction and desorption times as well as extraction temperature were studied. The linear concentration range of application was 0.5–250 ng mL⁻¹ for both compounds, with a detection limit of 0.06 ng mL⁻¹ for tebufenpyrad and 0.02 ng mL⁻¹ for oxadiazon. SPME-GC-MS analysis yielded good reproducibility (RSD between 7.5–10.1%). It was used to check the eventual existence of tebufenpyrad and oxadiazon above this limit in water and soil samples from Granada (Spain) as well as in human urine samples. The method validation was completed with spiked matrix samples. It can be applied as a monitoring tool for water, soil and urine in the investigation of environmental and occupational exposure to tebufenpyrad and oxadiazon.     

A new validated high-performance liquid chromatographic method for the determination of EGIS-9933 in rat plasma

Summary A new highly sensitive high-performance liquid chromatographic (HPLC) procedure for determination of EGIS-9933 (a newly developed anxiolytic compound) in rat plasma is described. A gradient, elution method with UV detection at 270 nm has been developed using a mobile phase of a mixture of A: methanol:acetonitrile 1:9 and B:0.5% triethilamine in water, the pH of B was adjusted to 3 with phosphoric acid. Solid phase extraction (SPE) was used for the sample preparation. The calibration was linear in the 10–10000 ng mL⁻¹ concentration range. The limit of quantification was 10 ng mL⁻¹. The bioanalytical method was validated according to internationally accepted criteria for biological samples. Presented at: Balaton Symposium on High-Performance Separation Methods, Siófok, Hungary, September 3–5, 1997.     

Determination of carbofuran, carbaryl and their main metabolites in plasma samples of agricultural populations using gas chromatography–tandem mass spectrometry

A gas chromatography–tandem mass spectrometric (GC-MS/MS) method has been developed for the determination of carbofuran (2,3-dihydro-2,2-dimethylbenzofuran-7-yl methylcarbamate), carbaryl (1-naphthyl-N-methylcarbamate) and their main metabolites in human blood plasma. Optimization of the isolation of the compounds from plasma matrix included the precipitation, denaturation and digestion of plasma proteins. Derivatization was achieved by the use of trifluoroacetic acid anhydride and was optimized for temperature, time and volume of derivatization agent. In the proposed method, a mild precipitation technique was applied using β-mercaptoethanol and ascorbic acid in combination with solid-phase extraction technique using Oasis HLB (Hydrophobic Lipophilic Balance) cartridges for further clean up of samples. Carbamate linkage was not hydrolyzed to its phenol product, but both carbamate phenol and ketones were transformed into trifluoroacetyl derivatives in order to become volatile compounds and were determined using tandem mass spectrometry. The linearity of the method was shown for nine concentrations in the range of 0.50–250 ng mL⁻¹ in fortified plasma aliquots. Limits of detection (LODs) for all compounds ranged from 0.015–0.151 ng mL⁻¹. Inter-day and intra-day assays (RSD) for all compounds, at three concentration levels of 2.5, 25 and 100 ng mL⁻¹ (n=3) in fortified plasma samples were less than 18%. Accuracy (%E _r) was calculated at three concentration levels, 8, 80 and 160 ng mL⁻¹ (n=3), and ranged from −12.0 to 15.0%. Matrix effect was evaluated so mean recoveries were calculated for all compounds and ranged from 81–107%. Specificity for the use of this method to biological monitoring studies was achieved including four main metabolites of CF, 1-naphthol and 2-naphthol from the naphthalene metabolism pathways, and both the parent compound of carbofuran and carbaryl. The proposed method was applied to plasma samples of pesticide users.     

An improved HPLC-ED method for monitoring plasma levels of clozapine and its active metabolites in schizophrenic patients

Summary An HPLC method with electrochemical detection has been developed for the determination of clozapine and its main metabolites, desmethylclozapine and clozapine N-oxide, in human plasma. An accurate pretreatment of the biological samples was implemented by means of solid phase extraction (SPE) on HLB cartridges. This improved pretreatment, together with a new mobile phase, allows for the accurate determination of clozapine N-oxide, which could not be quantitated by a previous method. The method uses only 100 μL of plasma for one complete analysis and shows good recovery values for all three analytes. The eluates from the SPE procedure were chromatographed in a reversed phase C18 column using a mobile phase composed of phosphate buffer, acetonitrile and methanol. Clozapine, desmethylclozapine and clozapine N-oxide were eluted in less than 10 minutes, without any interference from the biological matrix. Linearity was observed over the 2.50–150 ng mL⁻¹ (clozapine and desmethylclozapine) or 1.25–75 ng mL⁻¹ clozapine N-oxide) range for the three analytes, with satisfactory repeatability values. The limit of detection was 0.3 ng mL⁻¹ for clozapine and desmethylclozapine, samples of patients treated with Leponex gave good results. No interference from other common central nervous system drugs was found. This method seems to be a useful tool for pharmacokinetic studies and for clinical monitoring, because of its need for small plasma samples and its high sensitivity and selectivity.     

Simple and Rapid Determination of Benzoylphenylurea Pesticides in River Water and Vegetables by LC–ESI-MS

Liquid chromatography with electrospray mass spectrometry (LC–ESI-MS) instrumentation equipped with a single quadrupole mass filter has been used to determine several benzoylphenylurea insecticides (diflubenzuron, triflumuron, hexaflumuron, lufenuron and flufenoxuron). Chromatographic and MS parameters were optimised to obtain the best sensitivity and selectivity for all pesticides. Solid-phase extraction (SPE) using C₁₈ cartridges was applied for preconcentration of pesticide trace levels in river water samples. Recoveries of benzoylphenylurea pesticides from spiked river water (0.01 and 0.025 μg L⁻¹) were between 73 and 110% and detection limits were between 3.5 and 7.5 ng L⁻¹. The applicability of the method to the determination of benzoylphenylurea insecticides in spiked cucumber, green beans, tomatoes and aubergines was evaluated. Samples were extracted into dichloromethane without any clean-up step. The limits of detection ranged from 1.0 to 3.2 ng mL⁻¹ (0.68 and 2.13 μg kg⁻¹ in the vegetable samples). Mean recoveries ranged from 79 to 114% at spiking levels of 0.01 and 0.03 mg kg⁻¹. The method was applied to determine traces of benzoylphenylureas in both river water and vegetable samples with precision values lower than 10%. Interferences due to the matrix effect were overcome using matrix-matched standards.     

Improved HPLC determination of fluoxetine and norfluoxetine in human plasma

Summary An HPLC method with fluorescence detection has been developed for the determination of fluoxetine and its main metabolite norfluoxetine in human plasma. Pretreatment of the biological samples by liquid-liquid extraction was used to improve the sensitivity of a previously published SPE procedure. The method uses 200 μL plasma and recovery is good for both analytes. On a C₈ column with a mixture of perchlorate buffer and acetonitrile as mobile phase fluoxetine, norfluoxetine and the internal standard (paroxetine) were eluted in less than 9 min, without interference from the biological matrix. Response for both analytes was linearly dependent on concentration over the range 2.5–500 ng mL⁻¹, and repeatability (RSD%) was <4%. The limit of detection was 1 ng mL⁻¹ for both fluoxetines. Application to plasma samples from depressed patients treated with fluoxetine gave good results. There was no interference from other common CNS drugs. This method seems to be a useful tool for clinical monitoring, because it requires small plasma samples and is highly sensitive and highly selective.     

HPLC Determination of DCJW in Rat Plasma and Its Application to Pharmacokinetics Studies

A high-performance liquid chromatography–UV method for determining DCJW concentration in rat plasma was developed. The method described was applied to a pharmacokinetics study of intramuscular injection in rats. The plasma samples were deproteinized with acetonitrile in a one-step extraction. The HPLC assay was carried out using a VP-ODS column and the mobile phase consisting of acetonitrile–water (80:20, v/v) was used at a flow rate of 1.0 mL min⁻¹ for the effective eluting DCJW. The detection of the analyte peak area was achieved by setting a UV detector at 314 nm with no interfering plasma peak. The method was fully validated with the following validation parameters: linearity range 0.06–10 μg mL⁻¹ (r > 0.999); absolute recoveries of DCJW were 97.44–103.46% from rat plasma; limit of quantification, 0.06 μg mL⁻¹ and limit of detection, 0.02 μg mL⁻¹. The method was further used to determine the concentration–time profiles of DCJW in the rat plasma following intramuscular injection of DCJW solution at a dose of 1.2 mg kg⁻¹. Maximum plasma concentration (C _max) and area under the plasma concentration–time curve (AUC) for DCJW were 140.20 ng mL⁻¹ and 2405.28 ng h mL⁻¹.     

Liquid chromatography time-of-flight mass spectrometry following sorptive microextraction for the determination of fungicide residues in wine

This work evaluates the suitability of sorptive microextraction, using disposable silicone sorbents, and liquid chromatography time-of-flight mass spectrometry (LC-TOF-MS) for the determination of 15 fungicides in wine. Under optimized conditions, wine samples (10 mL) were diluted with the same volume of ultrapure water and poured in a glass vessel containing a magnetic stirrer and 4 g of sodium chloride. Extractions were performed at room temperature for 4 h, using an inexpensive silicone disk (12 μL volume) exposed directly to the sample. Thereafter, analytes were recovered with 0.2 mL of acetonitrile. The electrospray ionization (ESI) source was operated in the fast polarity switching mode obtaining, in the same injection, selective LC-MS records (extracted with a mass window of 10 ppm) of compounds rendering [M + H]⁺ and [M-H]⁻ ions. The method provided limits of quantification (LOQs) between 0.1 and 2.2 ng mL⁻¹, linear response ranges up to 500 ng mL⁻¹, relative recoveries from 75% to 117% and an inter-day variability below 15% for all analytes in red and white wine samples. The feasibility of in situ sample enrichment followed by delayed desorption and analysis is also assessed.     

Determination of phenolic compounds in water samples by on-line solid-phase extraction—supercritical-fluid chromatography with diode-array detection

Summary The eleven Environmental Protection Agency (EPA) priority phenolic compounds have been determined by solid-phase extraction (SPE) coupled on-line to supercritical-fluid chromatography (SFC) with diodearray detection. The variables affecting chromatographic separation were optimized and the analytes were separated at 40 °C in two diol columns connected in series; a gradient of methanol, as modifier, and CO₂ was used as mobile phase. Under these conditions, all the compounds studied were separated to baseline in less than 13 min. PLRP-S and LiChrolut EN were tested as sorbents in a 10×3 mm i.d. laboratory-packed precolumn for solid-phase extraction. An ion-pair reagent, tetrabutylammonium bromide (TBA), was used in the extraction process to increase break-through volumes. The performance of the method was checked with tap and river waters and the pre-concentration of 20 mL of sample in a PLRP-S pre-column enabled phenolic compounds to be determined at low μg L⁻¹ levels with limits of detection ranging between 0.4 and 2 μg L⁻¹. The repeatability and reproducibility between days (n=3) for real samples spiked at 10 μg L⁻¹ were lower than 10%.     

Combined use of carbon nanotubes and ionic liquid to improve the determination of antidepressants in urine samples by liquid chromatography

Antidepressants are widely used for the treatment of psychiatric disorders and therefore their monitoring in biological fluids is quite important taking into account that they can produce dangerous biochemical imbalances in toxic doses. A method for the determination of antidepressants in urine samples is presented using solid-phase extraction (SPE) and high-performance liquid chromatography (HPLC) with ultraviolet (UV) detection. Home-made cartridges containing 30 mg multiwall carbon nanotubes are employed for isolation of the analytes from the sample, allowing also the preconcentration of the analytes prior to the HPLC analysis. Chromatographic separation was achieved in a reversed-phase C₈ column using the ionic liquid 1-butyl-3-methylimidazolium trifluoromethanesulfonate as silanol activity suppressor, which enhances peak symmetry and chromatographic resolution. Limits of detection were 12.3 ng mL⁻¹ for trazodone and 90.1 ng mL⁻¹ for fluoxetine. The repeatability of the proposed method expressed as RSD (n = 11) varied between 3.4% (fluoxetine) and 5.0% (desipramine and mianserine). Thus, the method is suitable for the therapeutic monitoring of antidepressants in urine samples.     

Determination of olanzapine and desmethylolanzapine in the plasma of schizophrenic patients by means of an improved HPLC method with amperometric detection

Summary An improved HPLC method with electrochemical detection has been developed for the determination of olanzapine and its main metabolite, desmethylolanzapine, in human plasma. Chromatographic separation and analysis were performed on a C₈ reversed-phase column with a mixture of methanol, acetonitrile, and pH 3.7 phosphate buffer as mobile phase; 2-methylolanzapine was used as internal standard. Careful pretreatment of the plasma samples was implemented by means of solid phase extraction (SPE). Response was linearly dependent on concentration and precision was satisfactory over the concentration range 0.5–75.0 ng mL⁻¹ for both analytes. The limit of detection was 0.2 ng mL⁻¹ for both analytes. Application to plasma samples of patients treated with Zyprexa tablets gave good results. Because of its sensitivity and selectivity, and the need for small plasma samples, this method seems to be a useful tool for clinical monitoring.     

Highly Sensitive and Selective Detection of Creatinine by Combined Use of MISPE and a Complementary MIP-Sensor

Guanidinoacetate methyltransferase deficiency is a recently discovered inborn defect of creatine biosynthesis which reduces serum creatinine concentrations to as low as 0.58 μg mL⁻¹ (or 0.00058 μg mL⁻¹ after 1,000-fold dilution). To measure ultra trace levels of creatinine in diluted samples, molecularly imprinted solid-phase extraction (MISPE) and molecularly imprinted polymer (MIP) sensor techniques have been found to be inadequate. A combination of these techniques (i.e. MISPE hyphenated with use of an MIP-sensor), reported in this paper, has been found to be highly suitable for direct assay of creatinine in highly diluted human blood serum without complicated pretreatment of the sample. The proposed technique has the potential to enhance the sensitivity of creatinine measurement from μg mL⁻¹ to ng mL⁻¹ in highly dilute aqueous samples in which the concentrations of interfering constituents are reduced to negligible levels. In this work the sensitivity to creatinine was found to be improved compared with that of the MIP-sensor method alone (limit of detection, LOD, 0.00149 μg mL⁻¹). After preconcentration by MISPE and use of the sensor the detection limit for creatinine was as low as 0.00003 μg mL⁻¹ (RSD = 0.94%, S/N = 3; 50-fold preconcentration factor) in aqueous samples.     

Determination of phenols in waters using micro-pumped multicommutation and spectrophotometric detection: an automated alternative to the standard procedure

An automated and greener spectrophotometric procedure has been developed for the determination of phenol in water at 700 nm. The method uses the reaction between phenol, sodium nitroprusside, and hydroxylamine hydrochloride in a buffered medium at pH 12.3. The flow manifold comprises four solenoid micro-pumps employed for sample and reagent introduction into the reaction coil and to transport the colored product formed to the detector. The linear dynamic range was 50–3,500 ng mL⁻¹ (R = 0.99997; n = 6) and the method provided a limit of detection (3σ) of 13 ng mL⁻¹. The sampling throughput was estimated to be 65 measurements per hour and the coefficient of variation was 0.5% (n = 10) for a 1.0 μg mL⁻¹ phenol concentration. Recoveries of 92–105% were obtained for phenol determination in spiked water samples at concentration levels from 50 to 5,000 ng mL⁻¹. The use of multicommutation reduced the reagent consumption 25-fold, the sample consumption 225-fold, and the waste generation 30-fold compared with the batch procedure. The proposed method is an environmentally friendly alternative to the official 4-aminoantipyrine method since it avoids the use of chloroform.