复合聚合物修饰的粉末微电极及其对亚硝酸根还原的催化

本论文简述用Nafion_Os(bpy) 3 2 + /PVP复合膜修饰的乙炔黑粉末微电极 ,以亚硝酸根还原为模型反应 ,实现从复合修饰及扩大电极比表面两方面改善电极性能的思路 .结果表明 ,它同时显示Nafion_Os(bpy) 3 2 + /PVP修饰电极对NO2 -及NO+ 双重富集并再生活性粒子NO+ 、防止中继体流失、加速膜中中继体传输、改变反应途径等复合修饰电极的多种功能以及粉末微电极的高比表面、高液相传质速度以及薄层效应的特性 .与平面修饰电极及裸粉末微电极相比 ,它明显提高了酸性溶液中亚硝酸根还原的可逆性、呈数量级地提高稳态极限电流密度以及NO2 -的检测指标 .     

宏观均相多孔电极电化学阻抗谱基础

电化学阻抗谱可用于诊断多孔电极内电荷转移反应,即界面电荷集聚和电荷传导,以及反应物质输运。本文采用复相量方法,在同态假设条件下,重新推演多孔电极阻抗谱模型,厘清传统多孔电极阻抗谱模型中的模糊性表述。(1) 定义多孔电极表征输入参数,包括电极基体电子电导率σ₁ 、电解质离子电导率σ₂、界面电荷传递电导率g_ct、单位面积界面电容C、固相扩散系数D、速度常数k、电极厚度d、特征孔深L_p 和单位体积表面积S_c;(2) 解析阻抗谱特征输出参数,包括场扩散常数K,特征频率ω₀、ω₁、ω₂、ω₃和 ω_max,它们分别相关于界面传导反应、有限场扩散、氧化还原反应、孔内扩散和最小特征孔尺寸,以及分别对应于从传导到扩散和从扩散到饱和的转折频率f_k1 和f_k2;(3) 当参数X和Z同时变化时(X = σ₁和Z = d,S_c,L_p,C,g_ct,D,k),通过阻抗谱特征参数的演变规律,分析了电荷转移反应中X和Ζ参数耦合竞争;(4)为深入分析电荷转移反应中参数X和Z的耦合竞争,引入了分叉频率f_XZ和f_ZX 。f_XZ和f_ZX所处位置可以用于表征参数X和Z影响电荷转移反应的深度和广度。当分叉频率f_XZ和f_ZX不存在时,表明电荷转移反应中参数X和Z在全频率范围内存在耦合竞争。总之,借助于特征频率和分叉频率,本文一方面研究了动力学参数和微观结构参数对多孔电极中电荷转移反应的影响,另一方面分析谱图的变化及其背后的阻抗谱特征演化规律。本文研究结果可为阻抗谱的系统仿真和辨识提供理论基础,可为多孔电极内电荷转移反应的竞争分析提供技术支撑,还可为电化学储能系统的优化设计提供诊断工具。     

Amperometric detection with microelectrodes in flow injection analysis: theoretical aspects and application in the determination of nitrite in saliva

The construction of a wall-jet cell with amperometric detection using a set of disc electrodes whose radii ranged from 5 to 750 mum has been proposed. The influence of some experimental parameters like flow rate and electrode radius on hydrodynamic voltammograms recorded for a 0.5 mmol dm(-3) potassium ferrocyanide solution also containing 0.1 mol dm(-3) KCl has been discussed. Some considerations regarding the current signals obtained from flow injection experiments using both a 5- and a 750-mum radius platinum electrode were carried out in order to achieve the lowest limit of detection, a value of 0.03 mumol dm(-3) ferrocyanide being calculated by using the 5-mum radius microelectrode as amperometric detector. The wall-jet cell has been used in the determination of nitrite in saliva by quantifying the triiodide formed in the reaction of the analyte with excess iodide in acidic medium. A 12.5-mum platinum disc microelectrode maintained at +0.2 V vs. Ag/AgCl was used as amperometric detector. Peaks obtained in fiagrams after injection of diluted saliva to the carrier stream containing 0.1 mol dm(-3) sulphuric acid and 20 mmol dm(-3) potassium iodide were compared to an analytical curve obtained in the same conditions (r(2)=0.997) for a nitrite concentration in the range 1-10 mumol dm(-3). The concentration of nitrite in the saliva sample after the appropriate correction for dilution was found to be 2.3 ppm (0.05 mmol dm(-3)), in a good agreement with results obtained by using a standard spectrophotometric procedure (2.5 ppm). The limit of detection of the method was calculated as 0.2 mumol dm(-3), and the reproducibility was checked by measuring the peak current for 19 injections of 10 muM nitrite, the standard deviation being 3.7%.     

Electrochemical Detection of Nitric Oxide on a SWCNT/RTIL Composite Gel Microelectrode

Single walled carbon nanotubes (SWCNT) and room temperature ionic liquid (RTIL) were used to make a gel microelectrode for studies of the oxidation of nitric oxide (NO). The Faraday response of the gel microelectrode was contributed from two components: an outside‐surface microdisk and a thin‐layer cell formed by inner porous electrode materials, and enhanced by the thin‐layer effect. An EC mechanism, electrochemical NO oxidation followed by a chemical oxidation, was proposed. The gel microelectrode with a Nafion coating eliminated interferences from nitrite and some biomolecules, improved stability, and had a linear response range from 100 nM to 100 μM.     

钾掺杂g-C3N4薄膜光阳极的制备及光电催化氧化降解水中双氯芬酸钠性能

兼具高光学质量和电化学性能的薄膜光电极难以制备, 限制了光电催化氧化技术在水处理中的的应用. 本文采用原位煅烧法制备了负载在氧化铟锡(ITO)玻璃上的石墨相氮化碳(g-C₃N₄)薄膜电极, 并通过掺杂K⁺提高其光电催化氧化性能; 对电极进行了表征, 研究了其光电催化氧化降解水中双氯芬酸钠(DCF)的效率及降解路径. 结果表明, 原位煅烧法能制备出高质量的K⁺/g-C₃N₄薄膜光电极, K⁺的掺杂并未明显改变电极上g-C₃N₄的晶型、 价态和多孔形貌, 但可以提高ITO玻璃上g-C₃N₄的负载量, 增强电极对可见光的响应; K⁺的最佳掺杂浓度为0.002 mol/L, K⁺/g-C₃N₄薄膜电极光电催化氧化降解DCF的速率常数是纯g-C₃N₄薄膜电极的1.86倍; 当初始pH值为4, 电压为1 V, 光源强度为0.96 W/cm², 反应2 h后水中DCF降解率达到70%. K⁺/g-C₃N₄薄膜电极光电催化氧化过程中, 光催化氧化和电化学氧化之间存在协同作用, 两者相互增强, 并提高了反应过程中光生 空穴(h⁺)和羟基自由基(·OH)浓度, 在这两种活性物质作用下, 水中DCF分别被h⁺氧化生成咔唑衍生物、 与·OH发生加成反应生成多羟基芳香化合物, 最后开环生成小分子物质.     

以金属有机骨架材料HKUST-1为模板制备多孔聚苯胺电极及其超级电容器性能研究

以涂敷在碳布基体上的金属有机骨架多孔材料HKUST-1为硬模板,使用单极脉冲法沉积聚苯胺制备了具有电活性的多孔复合电极Micro-PANI/CC,同时以空白碳布(Carbon Cloth,CC)为基体制备了聚苯胺电极PANI/CC,并研究、比较了它们的电化学电容器性能. 使用XRD、SEM分析了所得电极的结构,结果显示电极Micro-PANI/CC表面具有大量的纳米孔状结构. 在0.5 mol·L^-1硫酸为电解液的体系中测试了循环伏安、恒电流充放电、阻抗以及稳定性等特性,在扫速为2 mV·s^-1 时,电极Micro-PANI/CC和PANI/CC的比电容分别为895.6 F·g^-1和547.6 F·g^-1,在其它测试条件相同的情况下,前者的比电容保持在后者的1.64倍以上,且具有更好的倍率特性、更低的电阻和较好的稳定性等特点,说明这种以HKUST-1为模板形成的多孔聚苯胺更适于超级电容器电极材料.     

A New and Simple Electrocatalyst for Formaldehyde Oxidation; Nickel/poly(o‐Anisidine)/Film Modified Ionic Liquid Carbon Paste Electrode

In present work, the ionic liquid, 1‐butyl‐3‐methylimidazolium bis (trifluoromethylsulfonyl) imide was incorporated in the carbon paste electrode as the binder (IL‐CPE). O‐anisidine (OA) monomer is electropolymerized in the presence of an aqueous acidic solution onto IL‐CPE (POA/IL‐CPE). The as‐prepared substrate is used as a porous matrix for dispersion of Ni(II) ions by immersing the modified electrode in a nickel(II) nitrite solution. The modified electrodes are characterized by scanning electron microscopy (SEM) and electrochemical methods. The POA/IL‐CPE was applied successfully to highly efficient (current density of 18.2 mA cm^?2) electrocatalytic oxidation of formaldehyde in alkaline medium. Finally, the rate constant for chemical reaction between formaldehyde and redox sites of the electrode was calculated.     

Microelectrode Combinations of Gold and Polypyrrole Enable Highly Stable Two-electrode Electrochemical Impedance Spectroscopy Measurements under Turbulent Flow Conditions

An electrochemical impedance spectroscopy (EIS) sensor design is proposed based on a standard interdigitated electrode layout in which the smaller working electrode consists of gold (Au) whereas the larger combined counter and reference electrode is coated with a porous layer of polypyrrole (PPy) doped with polystyrene sulfonate (PSS) (PPy : PSS). Each electrode material was first characterized by EIS in a standard 3-electrode setup with subsequent spectra fitting by a modified Randles equivalent circuit. The differences in the spectra obtained by the PPy : PSS coated electrodes can be explained by an increased electroactive surface area due to the porous polymer film. The changes in morphology of the film are discussed with respect to the evolution of the elements of the electric equivalent circuit. When applying the Au/PPy : PSS electrode combination to a standard 2-electrode arrangement, the enlarged highly electroactive surface area of the PPy : PSS coating lowers the interfacial impedance in a way that mainly the gold working electrode contributes to the overall system impedance. Therefore, obtaining reproducible EIS signals depends only on the electrode's open-circuit potential (OCP) and on additional adsorption events at the gold electrode/electrolyte interface. We present a protocol for microelectrode coating with PPy : PSS, which enables highly stable 2-electrode EIS experiments without the need of a reference electrode. This combination is believed to be very useful if an integration of sensing electrodes inside Micro Total Analysis Systems is aspired.     

Glassy carbon electrode modified with a film of poly(Toluidine Blue O) and carbon nanotubes for nitrite detection

This work describes the modification of a glassy carbon electrode with poly(Toluidine Blue O) (GC/poly-TBO) and single-walled carbon nanotubes (SWCNT) for the electrocatalytic oxidation of nitrite. GC/poly-TBO was prepared by electropolymerization and used as such or after immobilizing SWCNT on the polymeric film to give a composite GC/poly-TBO-SWCNT electrode. The electrochemical and catalytic behavior of both electrodes was studied comparatively. It was observed that the presence of SWCNT contributed to enhance the electrocatalytic response for nitrite oxidation, as measured by amperometry at +0.92 V vs. Ag/AgCl/KCl_sat and pH 7. The response was linear with respect to the nitrite concentration in the 0.001–4 mM range, with a detection limit of 0.37 μM (based on signal to noise ratio of 3) for GC/poly-TBO-SWCNT. The proposed method was also applied to the determination of nitrite in a wastewater sample and compared to the spectrophotometric method.     

Au/Fe3O4/壳聚糖纳米复合物NO2-传感电极

以壳聚糖为保护膜、玻碳为基底,用纳米Au和Fe₃O₄磁性纳米粒子构建了新型亚硝酸盐（NO₂^-）传感电极. 实验表明,该传感电极对NO₂^-有良好的电催化氧化活性,NO₂^-浓度(5.0×10^-6 ~ 2.0×10^-3 mol·L^-1)与氧化峰电流之间呈良好的线性关系（R = 0.9996）,检出限7.1×10^-7 mol·L^-1, 其灵敏度高、选择性好、重现性好.     

离子交换-电沉积法制备高Pt利用率多孔电极

采用离子交换-电沉积的方法(Ion-exchange/electrodeposition,IEE)制备了一种高Pt利用率催化电极,对所制备电极的表面形貌、催化活性及单电池性能用线性扫描伏安(LSV)、扫描电镜(SEM)、透射电镜(TEM)和单电池测试进行了表征. 结果表明,通过电极制备工艺和离子交换-电沉积参数的调控,能够消除碳载体表面官能团的影响,使铂阳离子只与全氟磺酸树脂(Nafion)上的H⁺进行交换. 在无铂离子的电解质中,将被交换的铂阳离子还原到与Nafion接触的碳载体上,使每一个铂纳米粒子都处于气体多孔电极的三相界面上,有效地调控铂纳米粒子的尺寸和分散度. 单电池测试表明,以铂载量为0.014 mgPt•cm^-2的IEE电极组装的电池的输出功率与铂载量为0.3 mgPt•cm-²的Nafion粘接Pt/C电极相当.     

三维多孔MnOx@In2O3立方盒子的构筑及储锌性能

锰基氧化物作为锌离子电池正极具有高比容量和低成本等优点, 但在电化学循环过程中不可逆相变、 锰的溶解和电极/电解质界面不稳定导致其在小电流密度、 深度放电条件下的循环性能差. 针对以上问题, 合成了三维(3D)多孔MnO_x立方盒子, 并在其表面包覆In₂O₃层, 获得3D多孔MnO_x@In₂O₃立方盒子. 结果显示, MnO_x@In₂O₃立方盒子具有大量孔径约10 nm左右的孔, 有利于H⁺和Zn²⁺的快速传输; In₂O₃包覆层均匀包覆于3D多孔MnO_x立方盒子的孔壁上, 有利于抑制MnO_x在电化学循环过程中的不可逆相变和锰的溶解, 稳定电极/电解质界面. 电化学测试结果表明, 该3D多孔MnO_x@In₂O₃电极在0.3 A/g的小电流密度、 深度放电条件下能稳定循环400次以上, 容量保持260 mA·h/g; 在1. 8 A/g电流密度下可稳定循环4000次以上, 容量保持81 mA·h/g; 即使在高电流密度6.0 A/g下仍保持73.4 mA·h/g的高可逆容量. 恒电流间隙滴定(GITT)和循环伏安测试结果表明, 3D多孔MnO_x@In₂O₃电极比3D多孔MnO_x具有更高的离子扩散速率, 有利于提升其高倍率容量. 电化学阻抗谱结果表明, 3D多孔MnO_x@In₂O₃电极具有比3D多孔MnO_x更稳定的电极/电解质界面, 有利于提升其循环寿命. 2000次循环后的扫描电子显微镜(SEM)结果表明, MnO_x@In₂O₃电极表面仍分布少量In₂O₃, 以确保电极/电解质界面和循环的稳定性.     

锂空气电池高容量长寿命Co3O4纳米空心球阴极催化剂

以六水合硝酸钴（Co(NO₃)₂·6H₂O）、六次甲基四胺（HMT）、蔗糖、柠檬酸钠（Na₃C₆H₅O₇）为原料,140 ^oC下水热碳化处理即得反应前驱物,经煅烧处理后,可得多孔Co₃O₄纳米空心球. 锂空气电池Co₃O₄/SP阴极催化剂具有优异的循环寿命性能,这归因于Co₃O₄空心球的纳米颗粒构成、较高比表面积的多孔结构,为电池反应提供了大量的反应位点,为充放电产物提供了足够的存储空间.     

Electrochemical Behavior of Mitoxantrone and Its Determination at a Pt／C Implanted Modified Microelectrode

In a 0.02 mol/L Na2HPO4-KH2PO4(PBS) buffer solution(pH=6.82), the electrochemical behavior of mitoxantrone was studied by linear-sweep voltammetry and cyclic voltammetry at a Pt/C ion implantation modified microelectrode. A sensitive reduction peak was observed. The peak potential was -0.72 V(vs.SCE), the peak current was proportional to the concentration of mitoxantrone within the ranges of 7.0×10-8-9.0×10-7 mol/L and 1.0×10-6-2.4×10-5 mol/L, with a detection limit of 4.0×10-8 mol/L. The linear correlation coefficients were 0.9994 and 0.9992, respectively. This method has been applied to the direct determination of mitoxantrone in simulated urine. The recoveries were in the range from 96.2% to 105.9%. The reduction process was a quasi-reversible one with adsorptive characteristics at the Pt/C microelectrode. The electrode reaction rate constant ks and the electron transfer coefficient α of the system were determined to be 4.5 and 0.65 s-1, respectively. The experiments showed that Pt element had surely been implanted into the surface of the carbon fiber, and the atomic Pt improved the electrocatalytic activity. The Pt/C microelectrode had a good stability and reproducibility.     

PVC膜修饰粉末微电极的研制及应用

聚合物具有催化、导电和选择分离等功能,将其与电极合为一体作为新的电极材料,可为改善固体电极的灵敏度、选择性和重现性提供一种新的手段［１,２］．我们用流延法［３］制得ＰＶＣ选择性渗透膜,覆盖于粉末微电极表面,制成了ＰＶＣ膜修饰粉末微电极．该电极性能稳定...     

Determination of nitrite based on mediated oxidation at a carbon paste electrode modified with a ruthenium polymer

The use of carbon paste electrodes modified with [Ru(bpy)(2)(PVP)(10)Cl]Cl for the mediated detection of nitrite is described. This surface modifier substantially lowers the overpotential for nitrite oxidation, hence permitting its determination at a lower potential. Various electrode characteristics were optimized, including the modifier loading and the monitoring potential, using batch amperometry. Standard calibration curves yielded slopes of 0.30 microA/microM over the linear range 5 x 10(-8)-5 x 10(-4)M nitrite with a detection limit of 3 x 10(-8)M (1.38 ppb) nitrite. The modified electrode response was shown to be relatively stable over a period of 5 days with a signal diminution of 8%. Electrode-to-electrode precision was measured as 11.4%. Flow-injection studies indicated the suitability of this electrode as a detector in flowing streams.     

Micro-Pt Array Electrode Towards CO Adsorption Investigated by Using In Situ FTIR Microscopy

The best-known quality of microelectrode is the low capacity of the interfacial double layer^[1]. In this paper, we have designed specially and fabricated an array electrode of micro-Pt (μ-Pt). 16 μ-Pt (200μm in diameter) electrodes were arranged in a 4 x 4 array, and the distance between each neighboring μ-Pt is 200μm. The associating designed electronic board allows to connect any individual μ-Pt or collective μ-Pts by selection with potentiostat, so the properties of an individual μ-Pt or arbitrarily grouped μ-Pt can be investigated conveniently. Moreover, by employing the in situ FTIR Microscopy^[2], the surface processes of CO adsorption on the array electrode were studied. Information at molecule level concerning the abnormal infrared effects (AIREs)^[3] of individual μ-Pt subjected to a fast potential scan treatment and the interaction between μ-Pts (coupled action) have been obtained for the first time.     

冠醚化合物的合成(ⅩⅪ)——开链酰胺型冠醚的合成及其钙离子选择电极的性能

本文以多甘醇为原料,经氧化、取代反应制备了多甘酰氯,再与仲胺反应,合成了7个开链酰胺型冠醚化合物和1个酰胺型大环化合物,除冠醚(Ⅰ)外,其余均未见文献报道。它们的结构经红外、核磁、质谱和元素分析数据确认,并用四圆单晶X射线衍射仪测定了冠醚(Ⅱ)单晶的晶体结构,进一步从理论上说明了它是优良的钙离子选择电极的中性载体。     

磷钼酸对直接甲醇燃料电池阴极氧还原的促进作用

以磷钼酸(H₄PMo₁₂O₄0·xH₂O,PMo₁₂)为直接甲醇燃料电池(DMFC)阴极添加剂,制备了Pt-PMo₁₂/C复合催化剂.电化学测试表明,该添加剂对于DMFC阴极氧还原具有明显的促进作用,与常规的Pt/C催化剂相比,相同载量下极限扩散电流提高了56.3%.在单电池性能测试中,这种促进作用使电池的最大输出功率提高了28%.     

粘结剂聚四氟乙烯乳液经过乙醇预处理后对气体扩散电极性能的影响

在气体扩散电极的制作工艺中,加入乙醇对粘结剂聚四氟乙烯(PTFE)进行预处理.通过伞自动微孔物理化学吸附仪对气体扩散电极进行BET比表面积、Langmuir比表面积、孔分布等进行测试,并用扫描电子显微镜(SEM)检测观察电极表观形貌.以锌电极作为负极组装成锌空气电池,检测在不同的电流密度下气体扩散电极相对锌电极的电位变化,研究PTFE乳液经过乙醇预处理后对电极性能的影响.结果显示,PTFE乳液经过乙醇处理后,先膨胀后收缩,能够增加催化层和气体扩散层的孔隙结构和比表面积,从而使得电极有效电化学反应场所相应增多,减低电极在大电流密度条件下放电时的极化过电位.