Effect of Coconut and Chestnut Flour Supplementations on Texture,Nutritional and Sensory Properties of Baked Wheat Based Bread

Wheat bread, produced by the single-phase method, is a common food consumed all over the world. Due to changes in lifestyle and nutritional trends, alternative raw materials are sought to increase the nutritional value and improve the taste of daily consumed products. Additionally, customers seek a wide variety of foods, especially when it comes to basic foods. Nuts, such as coconuts or chestnuts, might provide an attractive flavour with benefits to the nutritional quality. In this study, the effect of substituting wheat flour with coconut or chestnut flour (flour contribution level: 5, 10, 15, 30, 50% w/w), was evaluated in terms of the breads specific volume, texture, colour, nutritional composition, and dietary fibre fraction contents. Moreover, a sensory evaluation was conducted to assess potential consumer acceptance. Based on the consumer’s perception, the overall acceptance of bread with 15% w/w of coconut and chestnut flour was in privilege compared to the control sample. As a result, taking all of the tested parameters into account, the breads with 5, 10, and 15% supplementation of chestnut or coconut flour were still of good quality compared to the wheat bread and their fibre content was significantly higher.     

Effect of addition sesame seeds powder with different ratio on microstructural and some properties of low fat Labneh

Sesame seeds (Sesamum indicum L.) are probably the most ancient oil seed crops used in functional Labneh preperation. The goal of the present study was to explore the quality of Labneh made from skim milk fortified with 0%, 2%, 4%, and 6% sesame seeds powder (SSP) as alternative to fat. Control Labneh made from whole milk and their treatments with SSP were stored for 21 days at 5 ± 1 °C. The physiochemical, microbiological, and organoleptic properties were determined in fresh and stored Labneh (for 7, 14, and 21 days) as well as amino acids and microstructures were measured in fresh Labneh. The results showed that sesame seed contains up to 58.9% oil, 15.81% protein, 6.83% fiber, 11.03% carbohydrates, 14.84% antioxidant activity and 32.71 mg/100 g sesamol. The data presented that total solid, fat and acidity were increased while protein and ash contents were decreased in control Labneh compared with Labneh treatments. These all values increased with increasing the amount of SSP, except the acidity value decreased with increasing the amount of SSP. In various fresh Labneh samples, the major essential amino acid was Leucine and non-essential amino acid was Glutamic than the other amino acids. Microbiological examination of Labneh revealed that the total bacterial counts increased throughout the storage period. However moulds and yeasts were not detected at the first week then slightly detected and increased at the end of storage period. Coliform bacteria and spore-forming bacteria didn't observe in all Labneh treatments as storage progressed. Scanning electron microscopy showed that the control Labneh samples had more compact structure and fusion into big aggregates without voids. Labneh made from skim milk had numerous open, loose and less dense protein networks with spaces. No major differences were observed in the Labneh made from skim milk using 2% and 4% sesame seeds . Labneh made from skim milk using 6% sesame seeds was more intensive and thicker casein matrix than the other Labneh treatments. Organoleptic scores revealed that Labneh fortified with 4% sesame seeds powder have the highest acceptability properties.     

Effect of surface composition on the flowability of industrial spray-dried dairy powders

The surface composition of four industrial spray-dried dairy powders (skim milk powder, whole milk powder, cream powder and whey protein concentrate) was estimated by electron spectroscopy for chemical analysis (ESCA), and its influence on powder flowability was studied. It was found that skim milk powder flows well compared to the other powders because the surface is made of lactose and protein with a small amount of fat, whereas the high surface fat composition inhibits the flow of whole milk, cream and whey protein powders. However, the poor flowability of the powders with high surface fat coverage was drastically improved by removal of fat present on the surface through a brief wash with petroleum ether. The results obtained indicate that, although there are several parameters including particle size, which influence the flowability of powders, the flowability of powders is strongly influenced by the surface composition of powders, particularly for fat-containing powders.     

Anti-Obesity Effects of Matoa (Pometia pinnata) Fruit Peel Powder in High-Fat Diet-Fed Rats

Fruit peels, pericarps, or rinds are rich in phenolic/polyphenolic compounds with antioxidant properties and potentially beneficial effects against obesity and obesity-related non-communicable diseases. This study investigated the anti-obesity effects of matoa (Pometia pinnata) and salak (Salacca zalacca) fruit peel. Neither matoa peel powder (MPP) nor salak peel powder (SPP) affected the body weight, visceral fat weight, or serum glucose or lipid levels of Sprague–Dawley rats when included as 1% (w/w) of a high-fat diet (HFD). However, MPP significantly decreased the hepatic lipid level. MPP at a dose of 3% (w/w) of the HFD decreased body weight, visceral fat, and serum triglyceride levels as well as the hepatic lipid content. The inhibitory effect of MPP on hepatic lipid accumulation was not enhanced when its concentration was increased from 1% to 3% of the HFD. The anti-obesity effect of matoa was partly explained by the inhibitory effect of the matoa peel extract on fatty acid-induced secretion of ApoB-48 protein, a marker of intestinal chylomicrons, in differentiated Caco-2 cell monolayers. We identified hederagenin saponins that are abundant in MPP as potential anti-obesity substances. These results will contribute towards the development of functional foods with anti-obesity effects using the matoa fruit peel.     

Direct quantification of protein partitioning in oil-in-water emulsion by front-face fluorescence: avoiding the need for centrifugation

The quantification of proteins adsorbed at the oil-in-water interface is often difficult since it requires separation of fat globules from the aqueous phase that may damage the fat globule size and/or modify the interfacial composition. Front-face fluorescence spectroscopy was used to characterize the protein partitioning between the aqueous and oil phases of emulsions without separating these two phases. Different emulsions based on skim milk powder (SMP), two mono- and di-glyceride (MDG) mixtures (saturated and partially unsaturated), and three fats (hydrogenated and refined coconut oils and refined palm oil) were studied. The impact of an ageing period (24 h at 4 °C) was also investigated to typify the first step of ice cream processing. The emulsions were characterized for protein partitioning, immediately following emulsification and after ageing, using the Bradford spectrophotometric method, applied to the aqueous phase recovered after emulsion centrifugation. In parallel, the emulsions were characterized by their tryptophan emission fluorescence spectra. The area of the peaks at 333 nm, of the fourth-derivative fluorescence spectra corresponding to the amount of proteins present in the aqueous phase of emulsions, was well correlated with the Bradford measurements (r² = 0.91). This amount was also calculated from the fluorescence calibration curve obtained with SMP in solution. In conclusion, front-face fluorescence spectroscopy appeared to be a powerful and simple technique allowing the quantification of different populations of protein in an emulsified system, i.e., in the aqueous phase and loaded at the fat globule interface.     

Dilute Acid Hydrolysis of Wheat Straw Oligosaccharides

The dilute acid posthydrolysis of wheat straw hemicellulosic oligosaccharides obtained by autohydrolysis was evaluated. An empirical model was used to describe the effect of catalyst concentration (sulfuric acid, 0.1–4% w/w) and reaction time (0–60 min) based on data from a Doehlert experimental design. Catalyst concentration is the main variable influencing posthydrolysis performance, as both its linear and quadratic coefficients are statistically significant for the majority of the studied variables, namely, the ones related to sugar and byproducts production. Reaction time influences xylose and furan derivatives concentrations but not phenolics or acetic acid content. Catalyst concentration and reaction time interact synergistically, minimizing sugar recovery and promoting furan derivatives production. Based on the proposed models, it was possible to delimit an operational range that enables to obtain high monosaccharides recovery together with a slight decrease in inhibitors content as compared to the standard acid hydrolysis treatment. Furthermore, this is achieved with up to 70% less acid spending or considerable savings on reaction time.     

Physicochemical behavior of oil-in-water emulsions: influence of milk protein mixtures, glycerol ester mixtures and fat characteristics

Different emulsions based on two protein mixtures (skim milk powder (SMP) and functional dairy proteins (FDP)), two mono-di-glyceride mixtures (MDG) (saturated and partially unsaturated), three fats (hydrogenated and refined coconut oils and refined palm oil) were studied to investigate the interactions occurring between the oil phase, low molecular weight emulsifiers and proteins. Immediately following the emulsification process, high diameters of fat globules were obtained in FDP-based systems, relevant of an aggregation phenomenon. At this stage, the fat globule size characteristics were dependent on the emulsifier and fat types present in the formulation. In contrast, SMP-based emulsions were characterized by low proportions of aggregated particles regardless the formulations. Ageing (24 h at 4 °C) promoted disaggregation in FDP formulations, while SMP emulsions were well stabilized. Just after the homogenization step, less proteins were required to stabilize the globule interface in FDP systems as compared to SMP ones. Only with SMP, the amount of protein load at the fat globule surface was influenced by the oil nature and/or by the emulsifier type. A competitive adsorption of caseins, over whey proteins, was demonstrated in the case of FDP. The ageing period promoted a displacement of the proteins adsorbed at the oil droplet interface, suggesting a disruption of the interfacial protein interactions. This disruption was more marked with SMP than with FDP and, in both cases, was more or less influenced by the emulsifier and oil phase natures. The variations of the viscosity and rheological parameters (elastic and viscous moduli) were not dependent on one specific component of the formulation.     

Raman spectroscopic quantification of milk powder constituents

Raman spectroscopy has significant potential for the quantification of food products. Milk powder is an important foodstuff and ingredient that is produced on large scale (over 20 million tonnes per annum). Raman spectroscopy, unlike near- and mid-infrared spectroscopies, has not been used extensively to quantify milk powder constituents. The effect of sample presentation on spectroscopic calibrations of protein and fat for 136 New Zealand milk powders was assessed using Raman spectroscopy. Prediction models were produced to quantify a protein concentration range of 32.19-37.65% w/w for skim milk powder, and a protein concentration range of 23.34-25.02% w/w and a fat concentration range of 26.26-29.68% w/w for whole milk powder (where ratios of prediction to deviation exceeded 2.6 with one exception). The resultant calibrations were not influenced by sample orientation; the sample temperature during data collection did affect the calibrations. Calcium fortification in the form of calcium carbonate was identified within a sub-set of samples, reinforcing the efficacy of Raman spectroscopy for identifying both crystalline and non-crystalline constituents within milk powder.     

Effect of Three Defatting Solvents on the Techno-Functional Properties of an Edible Insect (Gryllus bimaculatus) Protein Concentrate

Edible insects have received global attention as an alternative protein-rich food. However, their structural characteristics make them difficult to digest. To overcome this obstacle, we assessed the techno-functional properties of three protein concentrates from the cricket Gryllus bimaculatus. Freeze-dried G. bimaculatus powder was defatted using ethanol, hexene, or acetone as solvents, and the techno-functional properties (protein solubility, water and oil holding capacity, foaming properties, emulsion capacity, and gel formation) of the protein concentrates were determined. Freeze-dried G. bimaculatus powder comprised approximately 17.3% crude fat and 51.3% crude protein based on dry weight. Ethanol was the most effective solvent for reducing the fat content (from 17.30% to 0.73%) and increasing the protein content (from 51.3% to 62.5%) of the concentrate. Techno-functionality properties drastically differed according to the defatting solvent used and foaming properties were most affected. Thus, the techno-functional and whole properties must be considered for proper application of edible insects to achieve global food sustainability.     

Low-Field NMR Study of Shortcake Biscuits with Cricket Powder,and Their Nutritional and Physical Characteristics

The growing human population renders challenges for the future supply of food products with high nutritional value. Here, we enhanced the functional and nutritional value of biscuits, a popular sweet snack, by replacing the wheat flour with 2%, 6%, or 10% (w/w) cricket powder. Consumer acceptance ratings for reference and 2% augmented cookies were comparable, whereas the higher levels of enhancement received inferior consumer scores. This relatively small change in biscuit recipe provided significant and nutritionally desirable enhancements in the biscuits, observed in a series of analyses. An increase in the protein content was observed, including essential amino acids, as well as minerals and fat. This conversion also affected the physical properties of the biscuits, including hardness, and water molecular dynamics measured by ¹H NMR. Cricket powder-augmented biscuits join the line of enhanced, functionally superior food products. This and similar food augmentation provide a viable scenario to meet the human food demands in the future.     

Characterization of Food Packaging Films with Blackcurrant Fruit Waste as a Source of Antioxidant and Color Sensing Intelligent Material

Chitosan and pectin films were enriched with blackcurrant pomace powder (10 and 20% (w/w)), as bio-based material, to minimize food production losses and to increase the functional properties of produced films aimed at food coatings and wrappers. Water vapor permeability of active films increased up to 25%, moisture content for 27% in pectin-based ones, but water solubility was not significantly modified. Mechanical properties (tensile strength, elongation at break and Young’s modulus) were mainly decreased due to the residual insoluble particles present in blackcurrant waste. FTIR analysis showed no significant changes between the film samples. The degradation temperatures, determined by DSC, were reduced by 18 °C for chitosan-based samples and of 32 °C lower for the pectin-based samples with blackcurrant powder, indicating a disturbance in polymer stability. The antioxidant activity of active films was increased up to 30-fold. Lightness and redness of dry films significantly changed depending on the polymer type. Significant color changes, especially in chitosan film formulations, were observed after exposure to different pH buffers. This effect is further explored in formulations that were used as color change indicators for intelligent biopackaging.     

Emulsification using micro porous glass (MPG): surface behaviour of milk proteins

To investigate the emulsifying properties and adsorption behaviour of high molecular amphiphilic substances such as proteins, it is important to maintain the native status of the used samples. The new method of micro porous glass (MPG) emulsification could offer an opportunity to do this because of the low shear forces. The oil-in-water emulsions were produced by dispersing the hydrophobic phase (liquid butter fat or sunflower oil) through the MPG of different average pore diameters (d_p=0.2 or 0.5 μm) into the flowing continuous phase containing the milk proteins (from reconstituted skim milk and buttermilk). The emulsions were characterised by particle size distribution, creaming behaviour and protein adsorption at the hydrophobic phase. The particle size distribution of protein-stabilised MPG emulsions is determined by the pore size of MPG, the velocity of continuous phase (or wall shear stress σ_w) and the transmembrane pressure. A high velocity of =2 m s⁻¹ (σ_w=13.4 Pa) and low pressure (pressure of disperse phase slightly exceeded the critical pressure Δp_TM=4.5 bar of 0.2 μm-MPG) led to the smallest droplet diameter. As a consequence of average droplet diameters of d₄₃>3.5 μm creaming was observed without centrifugation in all MPG emulsions after 24 h, but no coalescence of the oil droplets occurred. The study of protein adsorption showed that the MPG emulsification at low shear forces resulted in lower protein load values (2.5±0.5 mg m⁻²) than pressure emulsification (11.5±1.0 mg m⁻²). In addition, the various emulsification conditions (MPG or pressure homogenization) led to differences in the relative proportions of casein fractions, whey proteins and milk fat globule membranes (MFGM) at the fat globule surfaces.     

Changes in Particle Size,Sedimentation, and Protein Microstructure of Ultra-High-Temperature Skim Milk Considering Plasmin Concentration and Storage Temperature

Age gelation is a major quality defect in ultra-high-temperature (UHT) pasteurized milk during extended storage. Changes in plasmin (PL)-induced sedimentation were investigated during storage (23 °C and 37 °C, four weeks) of UHT skim milk treated with PL (2.5, 10, and 15 U/L). The increase in particle size and broadening of the particle size distribution of samples during storage were dependent on the PL concentration, storage period, and storage temperature. Sediment analysis indicated that elevated storage temperature accelerated protein sedimentation. The initial PL concentration was positively correlated with the amount of protein sediment in samples stored at 23 °C for four weeks (r = 0.615; p < 0.01), whereas this correlation was negative in samples stored at 37 °C for the same time (r = −0.358; p < 0.01) due to extensive proteolysis. SDS-PAGE revealed that whey proteins remained soluble over storage at 23 °C for four weeks, but they mostly disappeared from the soluble phase of PL-added samples after two weeks’ storage at 37 °C. Transmission electron micrographs of PL-containing UHT skim milk during storage at different temperatures supported the trend of sediment analysis well. Based on the Fourier transform infrared spectra of UHT skim milk stored at 23 °C for three weeks, PL-induced particle size enlargement was due to protein aggregation and the formation of intermolecular β-sheet structures, which contributed to casein destabilization, leading to sediment formation.     

Effect of surfactant sucrose ester on physical properties of dairy whipped emulsions in relation to those of O/W interfacial layers

Dairy foams were manufactured on a pilot plant with various sucrose ester contents. Oil-in-water emulsions were produced by high-pressure homogenisation of anhydrous milk fat (20 wt%) with an aqueous phase containing skim milk powder (6.5 wt%), sucrose (15 wt%), hydrocolloids (2 wt%), and sucrose esters. Sucrose ester content was varied from 0 to 0.35 wt%. Firmness and stability of dairy foams were determined. The fraction of protein associated with emulsion fat droplets and the compression isotherms of those droplets were determined as a function of sucrose ester content. With less than 0.1 wt% sucrose ester, no foam could be produced. The most firm and stable foams were obtained with ca. 0.1 wt% sucrose ester. The fraction of protein associated with emulsion droplets suddenly falls from 60% at a sucrose ester content lower than 0.1125% down to ca. 10-20% for higher surfactant content. Compression isotherms of emulsion droplets at the air-water interface show that, in the presence of surfactant, emulsion droplets disrupt and spread at the interface whilst without surfactant they become dispersed. This means that the presence of sucrose ester causes some destabilisation of fat droplet interfacial layers. There is hence an optimal sucrose ester content that allows some destabilisation of the oil-water interface without concomitant protein displacement from that interface. Consequently, with the recipe and manufacturing process used to produce dairy foams, there exists a compromise in sucrose ester content with regards to manufacture and shelf-life of dairy foams.     

The Purification and Characterization of Lipases from <Emphasis Type="Italic">Lasiodiplodia theobromae</Emphasis>, and Their Immobilization and Use for Biodiesel Production from Coconut Oil

The coconut kernel-associated fungus, Lasiodiplodia theobromae VBE1, was grown on coconut cake with added coconut oil as lipase inducer under solid-state fermentation conditions. The extracellular-produced lipases were purified and resulted in two enzymes: lipase A (68,000 Da)—purified 25.41-fold, recovery of 47.1%—and lipase B (32,000 Da)—purified 18.47-fold, recovery of 8.2%. Both lipases showed optimal activity at pH 8.0 and 35 °C, were activated by Ca²⁺, exhibited highest specificity towards coconut oil and p-nitrophenyl palmitate, and were stable in iso-octane and hexane. Ethanol supported higher lipase activity than methanol, and n-butanol inactivated both lipases. Crude lipase immobilized by entrapment within 4% (w/v) calcium alginate beads was more stable than the crude-free lipase preparation within the range pH 2.5–10.0 and 20–80 °C. The immobilized lipase preparation was used to catalyze the transesterification/methanolysis of coconut oil to biodiesel (fatty acyl methyl esters (FAMEs)) and was quantified by gas chromatography. The principal FAMEs were laurate (46.1%), myristate (22.3%), palmitate (9.9%), and oleate (7.2%), with minor amounts of caprylate, caprate, and stearate also present. The FAME profile was comparatively similar to NaOH-mediated transesterified biodiesel from coconut oil, but distinctly different to petroleum-derived diesel. This study concluded that Lasiodiplodia theobromae VBE1 lipases have potential for biodiesel production from coconut oil.     

Development and Physicochemical Properties of Low Saturation Alternative Fat for Whipping Cream

We developed an alternative whipping cream fat using shea butter but with low saturation. Enriched stearic-oleic-stearic (SOS) solid fat was obtained from shea butter via solvent fractionation. Acyl migration reactant, which mainly contains asymmetric SSO triacylglycerol (TAG), was prepared through enzymatic acyl migration to obtain the creaming quality derived from the β’-crystal form. Through enzymatic acyl migration, we obtained a 3.4-fold higher content of saturated-saturated-unsaturated (SSU) TAG than saturated-unsaturated-saturated (SUS) TAG. The acyl migration reactant was refined to obtain refined acyl migration reactant (RAMR). An alternative fat product was prepared by blending RAMR and hydrogenated palm kernel oil (HPKO) at a ratio of 4:6 (w/w). The melting points, solid fat index (SFI), and melting curves of the alternative products were similar to those of commercial whipping cream fat. The alternative fat had a content of total unsaturated fatty acids 20% higher than that of HPKO. The atherogenic index (AI) of alternative fat was 3.61, much lower than those of whipping cream fat (14.59) and HPKO (1220.3), because of its low atherogenic fatty acid content and high total unsaturated fatty acids. The polymorphic crystal form determined by X-ray diffraction spectroscopy showed that the β’-crystal form was predominant. Therefore, the alternative fat is comparable with whipping cream that requires creaming quality, and has a reduced saturated fat content.     

Effect of Coconut Protein and Xanthan Gum,Soybean Polysaccharide and Gelatin Interactions in Oil-Water Interface

We report on our study of the interactions between coconut protein extracted from coconut meat and three hydrocolloids (gelatin, xanthan gum, and soybean polysaccharide) and their interfacial adsorption and emulsification properties. We used Zeta potential, fluorescence spectroscopy scanning and ITC to investigate the interactions between a fixed concentration (1%) of coconut protein and varying concentrations of hydrocolloid. Through the interfacial tension and interfacial viscoelasticity, the interfacial properties of the hydrocolloid and coconut protein composite solution were explored. The physical stability of the corresponding emulsion is predicted through microstructure and stability analysis. Xanthan gum forms a flocculent complex with coconut protein under acidic conditions. Soy polysaccharides specifically bind to coconut protein. Under acidic conditions, this complex is stabilized through the steric hindrance of soy polysaccharides. Due to gelatin-coconut protein interactions, the isoelectric point of this complex changes. The interfacial tension results show that as time increases, the interfacial tensions of the three composite solutions decrease. The increase in the concentration of xanthan gum makes the interfacial tension decrease first and then increase. The addition of soybean polysaccharides reduces the interfacial tension of coconut protein. The addition of xanthan gum forms a stronger elastic interface film. Emulsion characterization showed that the gelatin-added system showed better stability. However, the addition of xanthan gum caused stratification quickly, and the addition of soybean polysaccharides also led to instability because the addition of polysaccharides led to a decrease in thermodynamic compatibility. This research lays the foundation for future research into coconut milk production technology.     

Influence of the fat characteristics on the physicochemical behavior of oil-in-water emulsions based on milk proteins-glycerol esters mixtures

Oil-in-water emulsions based on 10% milk protein preparation, 0.3% mono-di-glycerides (MDG) and 8% vegetable oil were prepared for models typifying ice cream formulations. Two MDG (saturated and partially unsaturated) and four fats (oleic oil, hydrogenated and refined coconut oils, refined palm oil) were chosen to investigate the interactions occurring between the oil phase, the MDG and the milk proteins. Influence of temperature (4 °C) and ageing (24 h at 4 °C) was also tested. The emulsions were characterized for protein desorption, particle size distribution and rheological properties. The dynamic surface activity of the milk proteins and the MDG at the oil-water interface was also determined. At 20 °C, emulsions were mostly stabilized by proteins although the protein load at the globule surface strongly depended on the emulsifier and the oil phase natures. A displacement of the proteins adsorbed at the oil droplet interface by the lipid surfactant was a consequence of the temperature decrease and/or ageing step, suggesting a disruption of the interfacial protein interactions. This disruption was more or less marked depending on the physicochemical characteristics of the surfactant and the oil used (amount of crystallized matter, fatty acid chain length and unsaturation degree). In parallel, the variation of the apparent viscosity of the various emulsions upon temperature was well correlated with the solid fat content. On the whole, the results obtained suggested that not only the surfactant molecules, i.e. emulsifiers and proteins, but also the fat used in the emulsion formulation participated in the development of the interface characteristics and rheological properties.     

Coconut Oil Alleviates the Oxidative Stress-Mediated Inflammatory Response via Regulating the MAPK Pathway in Particulate Matter-Stimulated Alveolar Macrophages

Exposure to particulate matter (PM) is related to various respiratory diseases, and this affects the respiratory immune system. Alveolar macrophages (AMs), which are defenders against pathogens, play a key role in respiratory inflammation through cytokine production and cellular interactions. Coconut oil demonstrates antioxidant and anti-inflammatory properties, and it is consumed worldwide for improved health. However, reports on the protective effects of coconut oil on the PM-induced respiratory immune system, especially in AMs, are limited. In this study, we generated artificial PM (APM) with a diameter approximately of 30 nm by controlling the temperature, and compared its cytotoxicity with diesel exhaust particles (DEP). We also investigated the antioxidant and anti-inflammatory effects of coconut oil in APM– and DEP–stimulated AMs, and the underlying molecular mechanisms. Our results showed that APM and DEP had high cytotoxicity in a dose-dependent manner in AMs. In particular, APM or DEP at 100 μg/mL significantly decreased cell viability (p < 0.05) and significantly increased oxidative stress markers such as reactive oxygen species (p < 0.01); the GSSH/GSH ratio (p < 0.01); and cytokine production, such as tumor necrosis factor-α (p < 0.001), interleukin (IL)-1β (p < 0.001), and IL-6 (p < 0.001). The expression of the genes for chemokine (C-X-C motif) ligand-1 (p < 0.05) and monocyte chemoattractant protein-1 (p < 0.001); and the proteins toll-like receptor (TLR) 4 (p < 0.01), mitogen-activated protein kinase (MAPK), and c-Jun N-terminal kinase (p < 0.001), p38 (p < 0.001); and extracellular receptor-activated kinase (p < 0.001), were also upregulated by PM. These parameters were reversed upon treatment with coconut oil in APM– or DEP–stimulated AMs. In conclusion, coconut oil can reduce APM– or DEP–induced inflammation by regulating the TLR4/MAPK pathway in AMs, and it may protect against adverse respiratory effects caused by PM exposure.Exposure to particulate matter (PM) is related to various respiratory diseases, and this affects the respiratory immune system. Alveolar macrophages (AMs), which are defenders against pathogens, play a key role in respiratory inflammation through cytokine production and cellular interactions. Coconut oil demonstrates antioxidant and anti-inflammatory properties, and it is consumed worldwide for improved health. However, reports on the protective effects of coconut oil on the PM-induced respiratory immune system, especially in AMs, are limited. In this study, we generated artificial PM (APM) with a diameter approximately of 30 nm by controlling the temperature, and compared its cytotoxicity with diesel exhaust particles (DEP). We also investigated the antioxidant and anti-inflammatory effects of coconut oil in APM– and DEP–stimulated AMs, and the underlying molecular mechanisms. Our results showed that APM and DEP had high cytotoxicity in a dose-dependent manner in AMs. In particular, APM or DEP at 100 μg/mL significantly decreased cell viability (p < 0.05) and significantly increased oxidative stress markers such as reactive oxygen species (p < 0.01); the GSSH/GSH ratio (p < 0.01); and cytokine production, such as tumor necrosis factor-α (p < 0.001), interleukin (IL)-1β (p < 0.001), and IL-6 (p < 0.001). The expression of the genes for chemokine (C-X-C motif) ligand-1 (p < 0.05) and monocyte chemoattractant protein-1 (p < 0.001); and the proteins toll-like receptor (TLR) 4 (p < 0.01), mitogen-activated protein kinase (MAPK), and c-Jun N-terminal kinase (p < 0.001), p38 (p < 0.001); and extracellular receptor-activated kinase (p < 0.001), were also upregulated by PM. These parameters were reversed upon treatment with coconut oil in APM– or DEP–stimulated AMs. In conclusion, coconut oil can reduce APM– or DEP–induced inflammation by regulating the TLR4/MAPK pathway in AMs, and it may protect against adverse respiratory effects caused by PM exposure.     

Microwave-Assisted Extraction of Curcuma longa L. Oil: Optimization,Chemical Structure and Composition,Antioxidant Activity and Comparison with Conventional Soxhlet Extraction

Curcuma root (Curcuma longa L.) is a very important plant in gastronomy and medicine for its unique antiseptic, anti-inflammatory, antimicrobial and antioxidant properties. Conventional methods for the extraction of curcuma oil require long extraction times and high temperatures that can degrade the active substances. Therefore, the objectives of the present study were: (i) first, to optimize the extraction yield of curcuma oil by applying a Box-Behnken experimental design using surface response methodology to the microwave-assisted extraction (MAE) technique (the independent variables studied were reaction time (10–30 min), microwave power (150–200 W) and curcuma powder/ethanol ratio (1:5–1:20; w/v); and, (ii) second, to assess the total phenolic content (TPC) and their antioxidant activity of the oil (at the optimum conditions point) and compare with the conventional Soxhlet technique. The optimum conditions for the MAE were found to be 29.99 min, 160 W and 1:20 w/v to obtain an optimum yield of 10.32%. Interestingly, the oil extracted by microwave-assisted extraction showed higher TPC and better antioxidant properties than the oil extracted with conventional Soxhlet technique. Thus, it was demonstrated that the method applied for extraction influences the final properties of the extracted Curcuma longa L. oil.