Non-destructive dating of fiber-based gelatin silver prints using near-infrared spectroscopy and multivariate analysis

An innovative approach to date fiber-based gelatin silver prints using near-infrared spectroscopy (NIR) and multivariate analysis is presented. NIR spectra were acquired for 152 film stills printed in the USA between 1914 and 1986, and partial least square (PLS) analysis was used to correlate the spectra with the year the photographs were printed. Principal component analysis and spectral interpretation helped clarify the underlying correlation between the print date and the composition and ageing of the photographic papers. The method was successfully validated with an independent set of 66 film stills printed in the USA, and a prediction error (root mean square error of prediction) of 6 years was achieved. The method was also tested on films stills printed in Germany and Russia, as well as amateur prints and photographs in the collection of the Museum of Modern Art. The prediction error was significantly larger, with the exception of the amateur prints, due to differences in the composition and/or properties of the papers depending on their geographical origin and purpose as confirmed by discriminant analysis.     

Detection of drug active ingredients by chemometric processing of solid-state NMR spectrometry data -- the case of acetaminophen

This paper presents a preliminary study in building discriminant models from solid-state NMR spectrometry data to detect the presence of acetaminophen in over-the-counter pharmaceutical formulations. The dataset, containing 11 spectra of pure substances and 21 spectra of various formulations, was processed by partial least squares discriminant analysis (PLS-DA). The model found coped with the discrimination, and its quality parameters were acceptable. It was found that standard normal variate preprocessing had almost no influence on unsupervised investigation of the dataset. The influence of variable selection with the uninformative variable elimination by PLS method was studied, reducing the dataset from 7601 variables to around 300 informative variables, but not improving the model performance. The results showed the possibility to construct well-working PLS-DA models from such small datasets without a full experimental design.     

基于近红外光谱的食用植物油中反式脂肪酸含量快速定量检测及模型优化研究

利用近红外光谱技术对食用植物油中反式脂肪酸(Trans fatty acids,TFA)含量进行快速定量检测,并通过波段选择、预处理方法、变量筛选及建模方法对TFA含量预测模型进行优化.采用AntarisⅡ傅里叶变换近红外光谱仪在4000~10000 cm-1光谱范围采集98个食用植物油样本的近红外透射光谱,然后采用气相色谱法测定TFA的真实含量.首先,对样本原始光谱进行波段、预处理方法优选;在此基础上,采用竞争自适应重加权法(Competitive adaptive reweighted sampling,CARS)筛选TFA相关的重要变量,最后应用主成分回归、偏最小二乘和最小二乘支持向量机方法分别建立食用植物油中TFA含量的预测模型.研究结果表明,近红外光谱技术检测食用植物油中的TFA含量是可行的,优化后的最佳预测模型的校正集和预测集R2分别为0.992和0.989,RMSEC和RMSEP分别为0.071%和0.075%.最佳预测模型所用的变量仅26个,占全波段变量的0.854%.此外,与全波段偏最小二乘预测模型相比,其预测集R2由0.904上升为0.989,RMSEP由0.230%下降为0.075%.由此表明,模型优化非常必要,CARS能有效筛选TFA相关的重要变量,极大减少建模变量数,从而简化预测模型,并较大提高预测模型的精度和稳定性.     

Simultaneous determination of methanol and ethanol in gasoline using NIR spectroscopy: effect of gasoline composition

Near infrared (NIR) spectroscopy was employed for simultaneous determination of methanol and ethanol contents in gasoline. Spectra were collected in the range from 714 to 2500 nm and were used to construct quantitative models based on partial least squares (PLS) regression. Samples were prepared in the laboratory and the PLS regression models were developed using the spectral range from 1105 to 1682 nm, showing a root mean square error of prediction (RMSEP) of 0.28% (v/v) for ethanol for both PLS-1 and PLS-2 models and of 0.31 and 0.32% (v/v) for methanol for the PLS-1 and PLS-2 models, respectively. A RMSEP of 0.83% (v/v) was obtained for commercial samples. The effect of the gasoline composition was investigated, it being verified that some solvents, such as toluene and o-xylene, interfere in ethanol content prediction, while isooctane, o-xylene, m-xylene and p-xylene interfere in the methanol content prediction. Other spectral ranges were investigated and the range 1449-1611 nm showed the best results.     

Application of Fourier transform infrared (FT-IR) spectroscopy combined with chemometrics for authentication of cod-liver oil

Some vegetable oils such as canola (CaO), corn (CO), soybean (SO), and walnut (WO) oils have similar color with cod liver oil (CLO), therefore, the presence of these oils was difficult to detect using naked eye. For this reason, Fourier transform infrared (FTIR) spectroscopy using horizontal attenuated total reflectance (HATR) as sampling accessory and in the combination with chemometrics was developed for detection and quantification of these vegetable oils as adulterants in CLO. The quantification of vegetable oils was carried out by using multivariate calibrations of partial least squares (PLS) and principle component regression (PCR), while the classification between pure CLO and CLOs adulterated with CaO, CO, SO, and WO was performed using discriminant analysis (DA). PLS with FTIR normal spectra was more suitable compared with PCR for quantification purposes with coefficient of determination (R²) higher than 0.99 and root mean square error of calibration (RMSEC) in the range of 0.04-0.82% (v/v). The PLS model was further used to predict the levels of these vegetable oils in independent samples for validation/prediction purpose. The root mean square error of prediction (RMSEP) values obtained were of 1.75% (v/v) (CaO), 1.39% (v/v) (CO), 1.35% (v/v) (SO), and 1.37% (v/v) (WO), respectively. The classification using DA revealed that the developed method can classify CLO and that mixed with these vegetable oils using 9 principal components.     

Cellulose I crystallinity determination using FT–Raman spectroscopy: univariate and multivariate methods

Two new methods based on FT–Raman spectroscopy, one simple, based on band intensity ratio, and the other using a partial least squares (PLS) regression model, are proposed to determine cellulose I crystallinity. In the simple method, crystallinity in cellulose I samples was determined based on univariate regression that was first developed using the Raman band intensity ratio of the 380 and 1,096 cm^?1 bands. For calibration purposes, 80.5% crystalline and 120-min milled (0% crystalline) Whatman CC31 and six cellulose mixtures produced with crystallinities in the range 10.9–64% were used. When intensity ratios were plotted against crystallinities of the calibration set samples, the plot showed a linear correlation (coefficient of determination R ² = 0.992). Average standard error calculated from replicate Raman acquisitions indicated that the cellulose Raman crystallinity model was reliable. Crystallinities of the cellulose mixtures samples were also calculated from X-ray diffractograms using the amorphous contribution subtraction (Segal) method and it was found that the Raman model was better. Additionally, using both Raman and X-ray techniques, sample crystallinities were determined from partially crystalline cellulose samples that were generated by grinding Whatman CC31 in a vibratory mill. The two techniques showed significant differences. In the second approach, successful Raman PLS regression models for crystallinity, covering the 0–80.5% range, were generated from the ten calibration set Raman spectra. Both univariate-Raman and WAXS determined crystallinities were used as references. The calibration models had strong relationships between determined and predicted crystallinity values (R ² = 0.998 and 0.984, for univariate-Raman and WAXS referenced models, respectively). Compared to WAXS, univariate-Raman referenced model was found to be better (root mean square error of calibration (RMSEC) and root mean square error of prediction (RMSEP) values of 6.1 and 7.9% vs. 1.8 and 3.3%, respectively). It was concluded that either of the two Raman methods could be used for cellulose I crystallinity determination in cellulose samples.     

激光诱导击穿光谱检测青菜中镉元素的多变量筛选研究

利用激光诱导击穿光谱(LIBS)技术与常规化学分析方法获取28个浓度梯度含Cd元素的青菜样品的LIBS谱线信息以及Cd含量信息.对获取的光谱信息结合标准归一化处理(SNV)、一阶导数(FD)、二阶导数(SD)、中心化处理(Center)作为偏最小二乘法(PLS)模型的优选方法;再根据4种预处理方法的预测结果选取最佳方法,同时将该方法作为间隔偏最小二乘法(iPLS)与联合区间间隔偏最小二乘法(SiPLS)优选青菜LIBS谱线的最佳波长区间.结果表明:通过SiPLS优选的特征波长区间分别为214.72 ～ 215.82 nm,215.88～ 216.97 nm,225.08 ～ 226.35 nm,并且经过中心化预处理后建立的验证模型效果最好,结果显示交叉验证均方根误差(RMSECV)为1.487,验证均方根误差(RMSEP)为1.094,相关系数(R)为0.9942,平均相对误差(ARE)为11.60％.研究结果表明,所选优化方法适合青菜中重金属Cd元素的LIBS校正模型的建立,且具有较好的预测效果.     

Horizontal attenuated total reflection applied to simultaneous determination of ash and protein contents in commercial wheat flour

Partial least-squares (PLS) regression was used to generate various models for the determination of both the protein and the ash contents of wheat flours by using spectroscopic data in the mid-infrared region obtained with a horizontal attenuated total reflectance (HATR) accessory. One hundred samples of wheat flour were used as purchased in the market: 55 for constructing the calibration model and 45 as external samples. The protein content varied between 8.85 and 13.23% and the ash content, between 0.330 and 1.287%, as determined by reference methods. Raw spectra and those corrected by multiplicative signal correction (MSC), first and second derivative spectra, were used as data for building the models. Different pre-treatments, such as mean centered and/or variance scaled (VS) methods, were tested and compared. Very good models were built as judged by the correlation coefficients (R²), root mean square error of calibration (RMSEC), root mean square error of validation (RMSEV) and root mean square error of prediction (RMSEP) that were obtained. Best results were achieved with MSC treated spectra.     

Fast determination of milk fat content using Raman spectroscopy

In our work, we have demonstrated the capability of VIS Raman spectroscopy in combination with partial least square regression (PLS) as a rapid technique for direct milk fat determination. Raman spectra of milk samples revealed contributions from proteins, but mainly from their fat content with different spectral characteristics. Three different methods of sample preparations were applied: (i) liquid milk contained in an open dish, (ii) dried milk droplets on glass plates covered with Al foil, and (iii) liquid milk contained in quartz cuvettes. Methods (i) and (ii) showed a good PLS model for milk fat prediction with low root mean square errors and high correlation coefficients. The main advantage of milk sample contained in the dish lies in its simplicity as well as the fact that the open container maximizes the signal of interest avoiding background contributions. Our results show that Raman spectroscopy is suited for in-line monitoring purposes.     

Determination of polyphenols in oats by near-infrared spectroscopy (NIRS) and two-dimensional correlation spectroscopy

Two-dimensional correlation spectroscopy (2DCOS) and near-infrared spectroscopy (NIRS) were used to determine the polyphenol content in oat grain. A partial least squares (PLS) algorithm was used to perform the calibration. A total of 116 representative oat samples from four locations in China were prepared and the corresponding near-infrared spectra were measured. Two-dimensional correlation spectroscopy was employed to select wavelength bands for the PLS regression model for the polyphenol determination. The number of PLS components and intervals was optimized according to the coefficients of determination (R²) and root mean square error of cross validation (RMSECV) in the calibration set. The performance of the final model was evaluated using the correlation coefficient (R) and the root mean square error of validation (RMSEV) in the prediction set. The results showed the band corresponding to the optimal calibration model was between 1350 and 1848?nm and the optimal spectral preprocessing combination was second derivative with second smoothing. The optimal regression model was obtained with an R² of 0.8954 and an RMSECV of 0.06651 in the calibration set and R of 0.9614 and RMSEV of 0.04573 in the prediction set. These measurements reveal the calibration model had qualified predictive accuracy. The results demonstrated that the 2DCOS with PLS was a simple and rapid method for the quantitative determination of polyphenols in oats.     

Selection of individual variables versus intervals of variables in PLSR

The selection abilities of the two well‐known techniques of variable selection, synergy interval‐partial least‐squares (SiPLS) and genetic algorithm‐partial least‐squares (GA‐PLS), have been examined and compared. By using different simulated and real (corn and metabolite) datasets, keeping in view the spectral overlapping of the components, the influence of the selection of either intervals of variables or individual variables on the prediction performances was examined. In the simulated datasets, with decrease in the overlapping of the spectra of components and cases with components of narrow bands, GA‐PLS results were better. In contrast, the performance of SiPLS was higher for data of intermediate overlapping. For mixtures of high overlapping analytes, GA‐PLS showed slightly better performance. However, significant differences between the results of the two selection methods were not observed in most of the cases. Although SiPLS resulted in slightly better performance of prediction in the case of corn dataset except for the prediction of the moisture content, the improvement obtained by SiPLS compared with that by GA‐PLS was not significant. For real data of less overlapped components (metabolite dataset), GA‐PLS that tends to select far fewer variables did not give significantly better root mean square error of cross‐validation (RMSECV), cross‐validated R² (Q²), and root mean square error of prediction (RMSEP) compared with SiPLS. Irrespective of the type of dataset, GA‐PLS resulted in models with fewer latent variables (LVs). When comparing the computational time of the methods, GA‐PLS is considered superior to SiPLS. Copyright © 2010 John Wiley & Sons, Ltd.     

过程分析技术(PAT)在原料药生产中的应用

该文通过采用近红外光谱分析技术对原料药(API)的浓度调节过程进行实时监控,介绍了在良好生产规范条件下过程分析技术(PAT)的实施过程。利用偏最小二乘算法开发出两个校正模型分别用以监控原料药和水分含量,并通过模型校正均方根误差(RMSEC)、交叉检验均方根误差(RMSECV)和预测均方根误差(RMSEP)以及对应的决定系数(R~2)来评估模型的性能。为保证模型性能,按照分析方法验证要求对模型的线性和范围、准确性、精密度(重复性)、专属性以及稳健性指标进行验证。最后通过系统性能测试确认检测系统满足商业化运行的要求。结果显示,采用过程分析技术控制浓度调节过程,可以大幅度缩短浓度调节时间,节约蒸汽能耗和检测费用,减少生产过程中的偏差,提升产品工艺水平和批次间一致性。     

Detecting the quality of glycerol monolaurate: A method for using Fourier transform infrared spectroscopy with wavelet transform and modified uninformative variable elimination

Glycerol monolaurate (GML) products contain many impurities, such as lauric acid and glucerol. The GML content is an important quality indicator for GML production. A hybrid variable selection algorithm, which is a combination of wavelet transform (WT) technology and modified uninformative variable eliminate (MUVE) method, was proposed to extract useful information from Fourier transform infrared (FT-IR) transmission spectroscopy for the determination of GML content. FT-IR spectra data were compressed by WT first; the irrelevant variables in the compressed wavelet coefficients were eliminated by MUVE. In the MUVE process, simulated annealing (SA) algorithm was employed to search the optimal cutoff threshold. After the WT-MUVE process, variables for the calibration model were reduced from 7366 to 163. Finally, the retained variables were employed as inputs of partial least squares (PLS) model to build the calibration model. For the prediction set, the correlation coefficient (r) of 0.9910 and root mean square error of prediction (RMSEP) of 4.8617 were obtained. The prediction result was better than the PLS model with full-spectra data. It was indicated that proposed WT-MUVE method could not only make the prediction more accurate, but also make the calibration model more parsimonious. Furthermore, the reconstructed spectra represented the projection of the selected wavelet coefficients into the original domain, affording the chemical interpretation of the predicted results. It is concluded that the FT-IR transmission spectroscopy technique with the proposed method is promising for the fast detection of GML content.     

近红外光谱结合膜富集技术测定饮料中微量邻苯二甲酸二异辛酯的含量

提出了一种基于在线膜富集的近红外漫反射光谱技术,对饮料中的微量塑化剂邻苯二甲酸二异辛酯(DEHP)进行快速检测。采用聚醚砜膜对饮料中的DEHP进行富集,将富集DEHP的膜直接进行近红外漫反射检测。参考DEHP的透射近红外光谱,对波数进行选择,以4 420～4 060、4 700～4 540、6 040～5 600cm-1作为建模的波数区间。通过比较原始光谱、多元散射校正、一阶求导、二阶求导及其组合,考察了光谱预处理方法对模型的影响,用去一交互验证法建立了偏最小二乘(PLS)模型,并用所建立的校正模型对校正集样品进行了预测。结果表明,在选定的波数区间,当用一阶求导对校正集光谱进行预处理时,所建立的模型对校正集的预测效果最佳,在隐变量数为7时,对校正集所有样品的校正均方根误差(RMSEC)为0.188 7mg/L。用此模型对预测集样品进行预测时,DEHP的质量浓度在0.5～5.0 mg/L范围内,预测均方根误差(RMSEP)为0.232 4 mg/L,平均相对预测误差为6.29%。     

Simultaneous determination of vitamin B12 and its derivatives using some of multivariate calibration 1 (MVC1) techniques

Resolution of binary mixtures of vitamin B12, methylcobalamin and B12 coenzyme with minimum sample pre-treatment and without analyte separation has been successfully achieved by methods of partial least squares algorithm with one dependent variable (PLS1), orthogonal signal correction/partial least squares (OSC/PLS), principal component regression (PCR) and hybrid linear analysis (HLA). Data of analysis were obtained from UV-vis spectra. The UV-vis spectra of the vitamin B12, methylcobalamin and B12 coenzyme were recorded in the same spectral conditions. The method of central composite design was used in the ranges of 10-80mgL(-1) for vitamin B12 and methylcobalamin and 20-130mgL(-1) for B12 coenzyme. The models refinement procedure and validation were performed by cross-validation. The minimum root mean square error of prediction (RMSEP) was 2.26mgL(-1) for vitamin B12 with PLS1, 1.33mgL(-1) for methylcobalamin with OSC/PLS and 3.24mgL(-1) for B12 coenzyme with HLA techniques. Figures of merit such as selectivity, sensitivity, analytical sensitivity and LOD were determined for three compounds. The procedure was successfully applied to simultaneous determination of three compounds in synthetic mixtures and in a pharmaceutical formulation.     

Determination of total nitrogen content, pH, density, refractive index, and brix in Thai fish sauces and their classification by near-infrared spectroscopy with searching combination moving window partial least squares

Near-infrared (NIR) transflectance spectra in the region of 1100-2500 nm were measured for 100 Thai fish sauces. Quantitative analyses of total nitrogen (TN) content, pH, refractive index, density and brix in the Thai fish sauces and their qualitative analyses were carried out by multivariate analyses with the aid of wavelength interval selection method named searching combination moving window partial least squares (SCMWPLS). The optimized informative region for TN selected by SCMWPLS was the region of 2264-2428 nm. A PLS calibration model, which used this region, yielded the lowest root mean square error of prediction (RMSEP) of 0.100% w/v for the PLS factor of 5. This prediction result is significantly better than those obtained by using the whole spectral region or informative regions selected by moving window partial least squares regression (MWPLSR). As for pH, density, refractive index and brix, the 1698-1722, and 2222-2258 nm regions, the 1358-1438 nm region, the 1774-1846, and 2078-2114 nm regions, and the 1322-1442, and 2000-2076 nm regions were selected by SCMWPLS as the optimized regions. The best prediction results were always obtained by use of the optimized regions selected by SCMWPLS. The lowest RMSEP for pH, density, refractive index and brix were 0.170, 0.007 g cm(-3), 0.0079 and 0.435 degrees Brix, respectively. Qualitative models were developed by using four supervised pattern recognitions, linear discriminant analysis (LDA), factor analysis-linear discriminant analysis (FA-LDA), soft independent modeling of class analog (SIMCA), and K neareat neighbors (KNN) for the optimized combination of informative regions of the NIR spectra of fish sauces to classify fish sauces into three groups based on TN. All the developed models can potentially classify the fish sauces with the correct classification rate of more than 82%, and the KNN classified model has the highest correct classification rate (95%). The present study has demonstrated that NIR spectroscopy combined with SCMWPLS is powerful for both the quantitative and qualitative analyses of Thai fish sauces.     

Classification and quantification analysis of Radix scutellariae from different origins with near infrared diffuse reflection spectroscopy

A rapid near infrared spectroscopy analysis method was developed for the geographical origin discrimination and content determination of Radix scutellariae, a kind of Traditional Chinese Medicine (TCM). 81 R. scutellariae samples from six different origins were analyzed with HPLC-UV as reference method. The NIR spectra were collected in integrating-sphere diffused reflection mode and processed with different spectra pretreated methods. Discriminant analysis (DA) and discriminant partial least squares (DPLS) were applied to classify the geographical origins of those samples, and the latter had a better predictive ability with 100% accuracy after two exceptional samples eliminated from the calibration set. For the quantitative calibration, the samples were divided into calibration set and validation set by Kennard-Stone algorithm. The models of baicalin, wogonoside, baicalein, wogonin were established with partial least squares (PLS) algorithm and the optimal principal component (PC) numbers were selected with Leave-One-Out (LOO) cross-validation. The established models were evaluated with the root mean square error of prediction (RMSEP) and corresponding correlation coefficients. The correlation coefficients of all the four calibration models are above 0.920, and the RMSEPs of baicalin, wogonoside, baicalein and wogonin are 0.752%, 0.094%, 0.418% and 0.139%, respectively. This research indicated that the NIR diffuse reflection spectroscopy could be used for the rapid analysis of R. scutellariae, which is beneficial to the quality control of this raw material in TCM pharmaceutical factory, and will also help to solve analogous problems.     

Simultaneous kinetic-spectrophotometric determination of sulfide and sulfite by partial least squares and genetic algorithm variable selection

Simultaneous multicomponent analysis is usually carried out by multivariate calibration models such as partial least squares (PLS) that utilize the full spectrum. It has been demonstrated by both experimental and theoretical considerations that better results can be obtained by a proper selection of the spectral range to be included in calculations. A genetic algorithm is one of the most popular methods for selecting variables for PLS calibration of mixtures with almost identical spectra without loss of prediction capacity. In this work, a simple and precise method for rapid and accurate simultaneous determination of sulfide and sulfite ions based on the addition reaction of these ions with new fuchsin at pH 8 and 25°C by PLS regression and using a genetic algorithm (GA) for variable selection is proposed. The concentrations of sulfide and sulfite ions varied between 0.05–2.50 and 0.15–2.00 μg/mL, respectively. A series of synthetic solutions containing different concentrations of sulfide and sulfite were used to check the prediction ability of GA-PLS models. The root mean square error of prediction with PLS on the whole data set was 0.19 μg/mL for sulfide and 0.09 μg/mL for sulfite. After the application of GA, these values were reduced to 0.04 and 0.03 μg/mL, respectively. The text was submitted by the authors in English.     

Quantitative determination of acyclovir in plasma by near infrared spectroscopy

The aim of this study was to assess the feasibility of near infrared spectroscopy (NIRS) for analysis of acyclovir in plasma. This methodology was based on the direct measurement of the transmission spectra of liquid samples and a multivariate calibration model (partial least squares, PLS) to determine the acyclovir concentration in plasma sample. The PLS calibration set was built on using the spiked samples by mixing different amounts of acyclovir. Concentration of acyclovir in the plasma samples was calculated employing a 6-factors PLS calibration using the spectral information in the range of 6102-5450 cm^− 1. The root mean square errors of prediction (RMSEP) found was 1.21 for acyclovir. The developed PLS-NIRS procedure allows the determination of 120 samples/h does not require any sample pretreatment and avoids waste generation.     

Characterization of Gasoline by 1H Nuclear Magnetic Resonance and Chemometrics

Automotive fuel adulteration is an old and significant problem. One common type of fuel adulteration is the addition of diesel to gasoline. Unsupervised models were developed through hierarchical cluster and principal component analysis models. Supervised models through partial least square discriminant analysis using ¹H nuclear magnetic resonance spectra as the input were used to classify samples as adulterated or unadulterated. Quantitative models were developed using partial least squares to determine the gasoline and diesel concentrations in the samples. This set contained samples composed of pure gasoline and anhydrous ethanol reproducing commercial gasoline and other samples treated with diesel. Hierarchical cluster and principal component analysis did not distinguish between adulterated and unadulterated samples except for the most adulterated materials. However, partial least square discriminant analysis classified 100% of the samples correctly. The partial least square algorithm provided excellent regression models for the gasoline and diesel content. The determination coefficient was 0.9920 for both models, whereas the root mean square error of cross-validation and root mean square error of prediction for the diesel model were 2.32 and 1.42%, respectively, and 2.40 and 1.38% for the gasoline model.