Influence of highly efficient PbS counter electrode on photovoltaic performance of CdSe quantum dots-sensitized solar cells

PbS electrode with high catalytic activity to S_n ^2? reduction certificated by the measurements of electrochemical impedance spectroscopy and cyclic voltammetry was prepared by a simple method. The high catalytic activity makes it be a low-cost alternative counter electrode to platinum (Pt) to be used in quantum dots-sensitized solar cells (QDSSCs) based on polysulfide electrolyte. The photovoltaic performance enhancement of the quantum dots (QDs)-sensitized semiconductor thin films due to the PbS counter electrode was evaluated by fabricating QDSSCs based on CdSe QDs-sensitized ZnO (SnO₂) thin film. CdSe QDs-sensitized ZnO thin film has the lower internal total series resistance and electron transmission time, the higher electron lifetime and electron collection efficiency than the CdSe QDs-sensitized SnO₂ thin film. Replacing the Pt counter electrode with the PbS counter electrode leads to more improvement on the short circuit photocurrent density for QDSSC based on the ZnO thin film than the SnO₂ thin film. Therefore, the process to limit the photovoltaic performance of CdSe QDs-sensitized solar cell and the possible way to improve the photovoltaic performance were analyzed.     

Spectral broadening in quantum dots-sensitized photoelectrochemical solar cells based on CdSe and Mg-doped CdSe nanocrystals

In order to absorb a broad spectrum in visible region, a co-sensitized TiO₂ electrode was prepared by CdSe and Mg-doped CdSe quantum dots (Q dots). The power conversion efficiency of the co-sensitized Q dots photoelectrochemical solar cells (PECs) showed 1.03% under air mass 1.5 condition (I = 100 mW/cm²), which is higher than that of individual Q dots-sensitized PECs. The incident-photon-to-current conversion efficiency of the co-sensitized PECs showed absorption peaks at 541 and 578 nm corresponding to the two Q dots and displayed a broad spectral response over the entire visible spectrum in the 500–600 nm wavelength domains.     

Chemical bath deposition of CdS quantum dots on vertically aligned ZnO nanorods for quantum dots-sensitized solar cells

Formation of CdS quantum dots (Q dots) on the vertically aligned ZnO nanorods electrode was carried out by chemical bath deposition. The diameter and thickness of ZnO nanorods are ～100–150 nm and ～1.6 μm, respectively, and CdS Q dots on ZnO nanorods have a diameter of smaller than 15 nm. In application of the Q dots-sensitized solar cells, composite film exhibited a power conversion efficiency of 0.54% under air mass 1.5 condition (80 mW/cm²), and incident-photon-to-current conversion efficiency showed 18.6%.     

High-efficiency cascade CdS/CdSe quantum dot-sensitized solar cells based on hierarchical tetrapod-like ZnO nanoparticles

Quantum dot-sensitized solar cells (QDSCs) constructed using cascade CdS/CdSe sensitizers and the novel tetrapod-like ZnO nanoparticles have been fabricated. The cascade co-sensitized QDSCs manifested good electron transfer dynamics and overall power conversion efficiency, compared to single CdS- or CdSe-sensitized cells. The preliminary CdS layer is not only energetically favorable to electron transfer but behaves as a passivation layer to diminish the formation of interfacial defects during CdSe synthesis. On the other hand, the anisotropic tetrapod-like ZnO nanoparticles, with a high electron diffusion coefficient, can afford a better carrier transport than traditional ZnO nanoparticles. The resultant solar cell yielded an excellent performance with a solar power conversion efficiency of 4.24% under simulated one sun (AM1.5G, 100 mW cm(-2)) illumination.     

A flexible photoelectrode for CdS/CdSe quantum dot-sensitized solar cells (QDSSCs)

We, for the first time, prepared a flexible photoelectrode for CdS/CdSe quantum dot-sensitized solar cells (QDSSCs). A power conversion efficiency of 3.47% was achieved under AM 1.5G illumination for a sandwich type QDSSC consisting of this flexible photoelectrode, Cu(2)S counter electrode and polysulfide electrolyte between the electrodes.     

Unpredicted electron injection in CdS/CdSe quantum dot sensitized ZrO2 solar cells

A quantum dot sensitized solar cell based on a porous ZrO(2) film, sensitized with CdSe quantum dots using CdS as an intermediate layer is presented. We observe electron injection from photo-excited quantum dots into the ZrO(2), which is unexpected due to the much higher conduction band edge (closer to the vacuum level) of bulk ZrO(2) compared to TiO(2).     

Synthesis of hybrid solar cells using CdS nanowire array grown on conductive glass substrates

High-density CdS nanowire (NW) arrays were successfully grown on fluorine-doped tin oxide (FTO)-coated glass substrates by vapor–liquid–solid (VLS) mechanism at a remarkably reduced temperature of ～450 °C. Bi catalyst layer and polyvinyl alcohol (PVA) played a major role in the low-temperature synthesis of high-quality CdS NW arrays. CdS NWs were defect free single crystalline Wurtzite crystals and they were 50–100 nm and 2–5 μm in diameter and length, respectively. CdS NWs were combined with poly[2-methoxy-5-(2′-ethylhexyloxy)-1,4-phenylenevinylene] (MEH-PPV), a conjugated polymer to form organic–inorganic hybrid structures. The UV–visible light absorption and emission behavior of MEH-PPV/CdS hybrids was investigated and their potential to be used as photovoltaic cells was demonstrated.     

Highly efficient CdS quantum dot-sensitized solar cells based on a modified polysulfide electrolyte

A modified polysulfide redox couple, [(CH(3))(4)N](2)S/[(CH(3))(4)N](2)S(n), in an organic solvent (3-methoxypropionitrile) was employed in CdS quantum dot (QD)-sensitized solar cells (QDSSCs), and an unprecedented energy conversion efficiency of up to 3.2% was obtained under AM 1.5 G illumination. The QDs were linked to nanoporous TiO(2) via covalent bonds by using thioglycolic acid, and chemical bath deposition in an organic solvent was then used to prepare the QDSSCs, facilitating high wettability and superior penetration capability of the TiO(2) films. A very high fill factor of 0.89 was observed with the optimized QDSSCs.     

P3HT as hole transport material and assistant light absorber in CdS quantum dots-sensitized solid-state solar cells

Regioregular poly(3-hexylthiophene) (P3HT) was employed as a hole transport material and assistant light absorber for the fabrication of a CdS quantum dot-sensitized solid-state solar cell, by which a power-conversion efficiency of 1.42% was achieved under an AM1.5 G (100 mW cm(-2)) condition.     

Sodium carboxymethyl starch-based highly conductive gel electrolyte for quasi-solid-state quantum dot-sensitized solar cells

Research on Chemical Intermediates - Liquid-junction quantum dot sensitized solar cells (QDSCs) have been facing a long stability issue due to the volatilization and leakage of liquid electrolytes....     

The performance of coupled (CdS:CdSe) quantum dot-sensitized TiO2 nanofibrous solar cells

Highly porous networks and reduced grain boundaries with one-dimensional (1-D) nanofibrous morphology offer enhanced charge transport in solar cells applications. Quantum dot (QDs) decorated TiO₂ nanofibrous electrodes, unlike organic dye sensitizers, can yield multiple carrier generations due to the quantum confinement effect. This paper describes the first attempt to combine these two novel approaches, in which CdS (～18 nm) and CdSe (～8 nm) QDs are sensitized onto electrospun TiO₂ nanofibrous (diameter ～80–100 nm) electrodes. The photovoltaic performances of single (CdS and CdSe) and coupled (CdS/CdSe) QDs-sensitized TiO₂ fibrous electrodes are demonstrated in sandwich-type solar cells using polysulfide electrolyte. The observed difficulties in charge injection and lesser spectral coverage of single QDs-sensitizers are solved by coupling (CdS:CdSe) two QDs-sensitizers, resulting in a enhanced open-circuit voltage (0.64 V) with 2.69% efficiency. These results suggest the versatility of fibrous electrodes in QDs-sensitized solar cell applications.     

CdS and CdSe quantum dots subsectionally sensitized solar cells using a novel double-layer ZnO nanorod arrays

We report a novel approach for synthesizing CdS and CdSe quantum dots subsectionally sensitized double-layer ZnO nanorods for solar cells, which are comprised of CdS QDs-sensitized bottom-layer ZnO NRs and CdSe QDs-sensitized top-layer ZnO NRs. X-ray diffraction study and scanning electron microscopy analysis indicate that the solar cells of subsectionally sensitized double-layer ZnO NRs, which are the hexagonal wurtzite crystal structure, have been successfully achieved. The novel structure enlarged the range of absorbed light and enhanced the absorption intensity of light. The I-V characteristics show that the double-layer structure improved both the current density (J_sc) and fill factor (FF) by 50%, respectively, and power conversion efficiency (η) was increased to twice in comparison with the CdS QDs-sensitized structure.     

Raman and photoluminescence investigation of CdS/CdSe quantum dots on TiO2 nanoparticles with multi-walled carbon nanotubes and their application in solar cells

Raman spectroscopy and photoluminescence (PL) were used to investigate the improved short-circuit current density (J_SC) of CdS/CdSe quantum dot (QD)-sensitized solar cells with multi-walled carbon nanotubes (MWCNTs). Raman and PL experiments were carried out in order to explore the hot-electron and cold-electron injections, respectively. The experimental results showed that the concentration of MWCNTs influences the hot-electron and cold-electron injections from CdS/CdSe QDs to TiO₂ nanoparticles. Therefore, the improved J_SC in CdS/CdSe QD-sensitized solar cells can be explained as due to the better electron injections.     

Sea urchin TiO2-nanoparticle hybrid composite photoelectrodes for CdS/CdSe/ZnS quantum-dot-sensitized solar cells

The sea urchin TiO(2) (SU TiO(2)) particles composed of radially aligned rutile TiO(2) nanowires are successfully synthesized through the simple solvothermal process. SU TiO(2) was incorporated into the TiO(2) nanoparticle (NP) network to construct the SU-NP composite film, and applied to the CdS/CdSe/ZnS quantum-dot-sensitized solar cells (QDSSCs). A conversion efficiency of 4.2% was achieved with a short-circuit photocurrent density of 18.2 mA cm(-2) and an open-circuit voltage of 531 mV, which corresponds to ～20% improvement as compared with the values obtained from the reference cell made of the NP film. We attribute this extraordinary result to the light scattering effect and efficient charge collection.     

A highly efficient capillary electrophoresis-based method for size determination of water-soluble CdSe/ZnS core-shell quantum dots

This paper describes a highly efficient method for size determination of water-soluble CdSe/ZnS core-shell quantum dots (QDs) by capillary electrophoresis (CE) using polymer additive as sieving medium. The influence of some factors, such as kinds and concentrations of the sieving medium, pH, concentrations of the background electrolyte (BGE) and applied voltage, on the separation of QDs was investigated. Under the optimal separation conditions, four different sized QDs were successfully separated, and the relative standard deviation (RSD) of the migration times for these QDs was below 1.013%. In addition, an equation was fit by taking into account the correlation existing between the electrophoretic mobilities and the sizes of a set of QDs. The feasibility of this equation to measure the sizes of other QDs was confirmed by comparison with the sizes obtained by transmission electron microscopy (TEM) experiment. This work offers a novel method for size determination of QDs, and provides an important reference on the study of QDs based on CE.     

Efficiency enhancement in PbS/CdS quantum dot-sensitized solar cells by plasmonic Ag nanoparticles

Journal of Solid State Electrochemistry - Semiconductor quantum dots (Q-dots) are attractive nanomaterials to be used in numerous research areas and device fabrication such as sensors,...     

Electrochemical/chemical synthesis of highly-oriented single-crystal ZnO nanotube arrays on transparent conductive substrates

Arrays of ZnO nanotube (ZNT) were prepared by a two-step electrochemical/chemical process on a transparent, conductive substrate from an aqueous solution at 85 °C. The as-grown ZNTs are single crystals with wurtzite structure and have good crystalline state. The tubular morphology was formed by the proton generated from anodic splitting of water and defect-selective etching of the electrodeposited ZnO nanorod (ZNR) along the c-axis. The photoluminescence and cathodoluminescence spectra of the ZNT arrays show two emission bands located in the ultraviolet (UV) and visible region, respectively. It was found that the PL intensity in the UV band as well as the ratio of I_uv/I_visible increased with increasing of the excitation intensity.     

Engineering arginine cross-linked mercaptoundecanoic acid CdSe/CdS/ZnS quantum dots for two-photon imaging of live cancer cells

Low toxicity arginine cross-linked mercaptoundecanoic acid CdSe/CdS/ZnS quantum dots were synthesized for two-photon imaging of live cancer cells.     

Wave function engineering for efficient extraction of up to nineteen electrons from one CdSe/CdS quasi-type II quantum dot

Solar-to-fuel conversion devices require not only efficient catalysts to accelerate the reactions, but also light harvesting and charge separation components to absorb multiple photons and to deliver multiple electrons/holes to the catalytic centers. In this paper, we show that the spatial distribution of electron and hole wave functions in CdSe/CdS quasi-type II quantum dots enables simultaneous ultrafast charge separation (0.18 ps to adsorbed Methylviologen), ultraslow charge recombination (0.4 μs), and slow multiple-exciton Auger annihilation (biexciton lifetime 440 ps). Up to nineteen excitons per QD can be generated by absorbing multiple 400 nm photons and all excitons can be dissociated with unity yield by electron transfer to adsorbed methylviologen molecules. Our finding demonstrates that (quasi-) type II nanoheterostructures can be engineered to efficiently dissociate multiple excitons and deliver multiple electrons to acceptors, suggesting their potential applications as light harvesting and charge separation components in artificial photosynthetic devices.     

CdSe/CdS量子点荧光猝灭法测定芹黄素的研究

以巯基乙酸为稳定剂,在水溶液中合成了具有特殊光学性质的水溶性CdSe/CdS量子点。以该量子点为荧光探针,基于荧光猝灭法对芹黄素进行了定量检测。考察了缓冲体系、反应时间、量子点浓度等多种因素的影响。实验结果表明,在0.001 mol/L、pH为6.80的KH2PO4-Na2HPO4缓冲液中,当量子点浓度为1.2×10^-4mol/L、反应时间为20 min时,该方法的线性范围为0.16-27.02μg/mL,其线性回归方程为F0/F=0.99665＋0.11067ρ（μg/mL）,相关系数r=0.998,检出限为0.13μg/mL,并用于合成样品的分析。