Electrospinning of poly(trimethylene terephthalate)/carbon nanotube composites

Poly(trimethylene terephthalate) (PTT) nanocomposites containing carbon nanotubes (CNTs) with different surface structure and aspect ratio were prepared by melt compounding for electrospinning. The dispersion state of the CNTs in the composites was then examined utilizing rheology tools. The results show that carboxylic surface functionalized CNTs present better dispersion in the matrix than hydroxy surface functionalized CNTs because the former has stronger affinity to the PTT. Besides surface functionalization, the aspect ratio of CNTs is also vital to their final dispersion. The CNTs with lower aspect ratio are dispersed as individuals or small bundles while those with higher aspect ratio are dispersed mainly as flocs with large hydrodynamic radius, showing higher effective volume fraction. The presence of CNTs has a large influence on the morphologies of electrospun fiber and on the appearances of CNTs in the fibers. In the presence of CNTs with lower aspect ratio, continuous composite fibers are obtained. But the structure of those continuous fibers highly depends on the surface group of CNTs. Carboxylic surface functionalized CNTs are well embedded by the PTT and oriented along the fiber axis during electrospinning, leading to bead-free and uniform fiber morphology; while hydroxy surface functionalized CNTs show tortuous conformations with less orientation in the fibers, and as a result, the obtained fibers show beaded and misshaped morphologies. In the case of higher aspect ratio, however, the CNTs prefer to exist as entanglements or knots in the streamlines, and thereby only beaded or even uncontinuous fibers are obtained. Therefore, the formation and fiber morphology of PTT/CNT composite fibers obtained by electrospinning strongly depend on the surface functional groups of the CNTs, as well as on the CNT structure.     

Isothermal crystallization kinetics of poly(butylene terephthalate)/attapulgite nanocomposites

Poly(butylene terephthalate) (PBT)/organo‐attapulgite (ATT) nanocomposites containing 2.5 and 5 wt % nanoparticles loadings were fabricated via a simple melt‐compounding approach. The crystal structure and isothermal crystallization behaviors of PBT composites were studied by wide‐angle X‐ray diffraction and differential scanning calorimetry, respectively. The X‐ray diffraction results indicated that the addition of ATT did not alter the crystal structure of PBT and the crystallites in all the samples were triclinic α‐crystals. During the isothermal crystallization, the PBT nanocomposites exhibited higher crystallization rates than the neat PBT and the varied Avrami exponents when compared with the neat PBT. At the same time, the regime II/III transition was also observed in all the samples on the basis of Hoffman‐Laurizten theory, but the transition temperature increased with increasing ATT loadings. The fold surface free energy (σ_e) of polymer chains in the nanocomposites was lower than that in the neat PBT. It should be reasonable to treat ATT as a good nucleating agent for the crystallization of PBT, which plays a determinant effect on the reduction in σ_e during the isothermal crystallization of the nanocomposites, even if the existence of ATT could restrict the segmental motion of PBT. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2112–2121, 2006     

Non-isothermal crystallization kinetics of poly(trimethylene terephthalate)/poly(ethylene 2,6-naphthalate) blends

The glass-transition temperature and non-isothermal crystallization of poly(trimethylene terephthalate)/poly(ethylene 2,6-naphthalate) (PTT/PEN) blends were investigated by using differential scanning calorimeter (DSC). The results suggested that the binary blends showed different crystallization and melting behaviors due to their different component of PTT and PEN. All of the samples exhibited a single glass-transition temperature, indicating that the component PTT and PEN were miscible in amorphous phase. The value of T_g predicted well by Gordon-Taylor equation decreased gradually with increasing of PTT content. The commonly used Avrami equation modified by Jeziorny, Ozawa theory and the method developed by Mo were used, respectively, to fit the primary stage of non-isothermal crystallization. The kinetic parameters suggested that the PTT content improved the crystallization of PEN in the binary blend. The crystallization growth dimension, crystallization rate and the degree of crystallinity of the blends were increased with the increasing content of PTT. The effective activation energy calculated by the advanced iso-conversional method developed by Vyazovkin also concluded that the value of E_a depended not only on the system but also on temperature, that is, the binary blend with more PTT component had higher crystallization ability and the crystallization ability is increased with increasing temperature. The kinetic parameters U^* and K_g were also determined, respectively, by the Hoffman-Lauritzen theory.     

Isothermal crystallization kinetics of poly(trimethylene terephthalate) under the influence of self-seeding nucleation

The effect of self-seeding nucleation on the crystallization behavior of poly(trimethylene terephthalate) (PTT) was studied. Differential scanning calorimetry (DSC) indicated that the crystallization temperature of PTT notably increased after self-seeding nucleation. Avrami equation was applied in the analysis of the isothermal crystallization process of PTT. The resulting average value of the Avrami exponent at n = 3.34 suggests that primary crystallization may correspond to a three-dimensional spherulitic growth. Self-seeding nucleation, leading to a decrease in active energy for crystallization and chain folding work, promotes the overall crystallization process of PTT. Translated from Acta Polymerica Sinica, 2006, (3): 414–417 (in Chinese)     

Isothermal crystallization kinetics and melting behavior of poly(ethylene terephthalate)/barite nanocomposites

Poly(ethylene terephthalate) (PET)/Barite nanocomposites were prepared by direct melt compounding. The effects of PET‐Barite interfacial interaction on the dynamic mechanical properties and crystallization were investigated by DMA and DSC. The results showed that Barite can act as a nucleating agent and the nucleation activity can be increased when the Barite was surface‐modified (SABarite). SABarite nanoparticles induced preferential lamellae orientation because of the strong interfacial interaction between PET chains and SABarite nanoparticles, which was not the case in Barite filled PET as determined by WAXD. For PET/Barite nanocomposites, the Avrami exponent n increased with increasing crystallization temperature. Although at the same crystallization temperature, the n value will decrease with increasing SABarite content, indicating of the enhancement of the nucleation activity. Avrami analyses suggest that the nucleation mechanism is different. The activation energy determined from Arrhenius equation reduced dramatically for PET/SABarite nanocomposite, confirming the strong interfacial interaction between PET chains and SABarite nanoparticles can reduce the crystallization free energy barrier for nucleus formation. In the DSC scan after isothermal crystallization process, double melting behavior was found. And the double endotherms could be attributed to the melting of recrystallized less perfect crystallites or the secondary lamellae produced during different crystallization processes. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 655–668, 2009     

Isothermal crystallization kinetics and mechanical properties of poly(butylene terephthalate)/attapulgite nanocomposites

Poly(butylene terephthalate) (PBT)/attapulgite (AT) nanocomposites were prepared by in situ polymerization. Morphology of the PBT/AT nanocomposites was observed by scanning electron microscope and polarizing optical microscope. Thermogravimetric analyses were used to examine the thermal stability. The melting behaviors, equilibrium melting temperature, isothermal crystallization behavior of pure PBT and PBT/AT nanocomposites were studied by differential scanning calorimetry. The results show that PBT/AT nanocomposites possess higher thermal stability than pure PBT, and AT nanoparticles play a heterogeneous nucleating agent in PBT crystallization that accelerated the crystallization rate. The PBT/AT nanocomposite with higher AT content could retard the transport of polymer chains to the growing crystals compared with that of PBT/AT nanocomposite in lower AT content. According to dynamic mechanical analysis results, the storage modulus of PBT/AT nanocomposites was markedly improved and the addition of AT nanoparticles promotes the crystallization of PBT, which decreases the amorphous area. Meanwhile, the well-dispersed AT nanoparticles also retard the movement of polymer chain segment and increase the proportion of rigid amorphous region.     

Isothermal crystallization kinetics and thermal behavior of poly(?-caprolactone)/multi-walled carbon nanotube composites

This study describes the preparation of poly(?-caprolactone) (PCL)/multi-walled carbon nanotube (MWCNT) composites by ultrasonically mixing the PCL and as-fabricated MWCNT in a tetrahydrofuran solution. The TEM images show that the MWCNT is well separated and uniformly distributed in the PCL matrix. Differential scanning calorimetry (DSC), thermogravimetric analyzer (TGA), X-ray diffraction (XRD) and polarized optical microscopy (POM) were used to investigate the isothermal crystallization kinetics, crystalline structure and thermal behavior of PCL and PCL/MWCNT nanocomposites. DSC isothermal results revealed that the activation energy of PCL extensively decreases with increasing MWCNT contents, suggesting that the loading of MWCNT into PCL matrix probably induced heterogeneous nucleation during crystallization processes. From TGA data, the addition of small amount of MWCNT into PCL matrix can improve the thermal stability of PCL matrix. TGA isothermal degradation data illustrate that the activation energy E_d of the composites is smaller than that of PCL. This phenomenon can be attributed to the incorporation of more MWCNT loading into PCL caused a decrease in the degradation rate and an increase in the residual weight for PCL/MWCNT nanocomposites.     

Melt-crystallization behavior and isothermal crystallization kinetics of crystalline/crystalline blends of poly(ethylene terephthalate)/poly(trimethylene terephthalate)

The melt-crystallization and isothermal melt-crystallization kinetics of poly(ethylene terephthalate)/poly(trimethylene terephthalate) blends (PET/PTT) were investigated by differential scanning calorimetry (DSC) and polarized optical microscopy. Although PET and PTT in the binary blends are miscible at amorphous state, they will crystallize individually when cooled from the melt. In the DSC measurements, PET component with higher supercooling degree will crystallize first, and then the crystallite of PET will be the nucleating agent for PTT, which induce the crystallization of PTT at higher temperature. On the other hand, in both blends of PET80/PTT20 and PET60/PTT40, the PET component will crystallize at higher temperature with faster crystallization rate due to the dilute effect of PTT. So the commingled minor addition of one component to another helps to improve the crystallization of the blends. For blends of PET20/PTT80 and PET40/PTT60, isothermal crystallization kinetics evaluated in terms of the Avrami equation suggest different crystallization mechanisms occurred. The more PET content in blends, the fast crystallization rate is. The Avrami exponent, n = 3, suggests a three-dimensional growth of the crystals in both blends, which is further demonstrated by the spherulites formed in all blends. The crystalline blends show multiple-melting peaks during heating process.     

Morphology development and crystallization behavior of poly(ethylene terephthalate)/poly(trimethylene terephthalate) blends

The spherulite morphology and crystallization behavior of poly(ethylene terephthalate) (PET)/poly(trimethylene terephthalate) (PTT) blends were investigated with optical microscopy (OM), small-angle light scattering (SALS), and small-angle X-ray scattering (SAXS). The thermal analysis showed that PET and PTT were miscible in the melt over the entire composition range. The rejected distance of non-crystallizable species, which was represented in terms of the parameter δ, played an important role in determining the morphological patterns of the blends at a specific crystallization temperature regime. The parameter δ could be controlled by variation of the composition, the crystallization temperature, and the level of transesterification. In the case of two-step crystallization, the crystallization of PTT commenced in the interspherulitic region between the grown PET crystals and proceeded until the interspherulitic space was filled with PTT crystals. The spherulitic surface of the PET crystals acted as nucleation sites where PTT preferentially crystallized, leading to the formation of non-spherulitic crystalline texture. The SALS results suggested that the growth pattern of the PET crystals was significantly changed by the presence of the PTT molecules. The lamellar morphology parameters were evaluated by a one-dimensional correlation function analysis. The blends that crystallized above the melting point of PTT showed a larger amorphous layer thickness than the pure PET, indicating that the non-crystallizable PTT component might be incorporated into the interlamellar region of the PET crystals. With an increased level of transesterification, the exclusion of non-crystallizable species from the lamellar stacks was favorable due to the lower crystal growth rates. As a result, the amorphous layer thickness of the PET crystals decreased as the annealing time in the melt state was increased.     

Isothermal crystallization studies of poly(butylene terephthalate) composites

Different crystallization kinetic models (Avrami and Tobin) have been applied to study the crystallization kinetics of virgin poly(butylene terephthalate) (PBT) and filled PBT systems under isothermal experimental conditions. The experimental data have been analyzed with a nonlinear, multivariable regression program. The kinetic parameters for the isothermal crystallization have been determined. The analysis results indicate that both models satisfactorily represent the isothermal crystallization kinetics. PBT crystallizes most slowly. The presence of nanoclays or nanofibers, added as fillers, enhances the crystallization rate of PBT composites. An analysis of the kinetic data with the Avrami and Tobin models has shown little change in the crystallization exponent compared with that of virgin PBT. The crystallization rate constant decreases with a rise in the temperature for the two models. This trend has been observed for similar polyester systems reported in the literature. The dispersion of the clay layers in the PBT nanocomposites has been characterized with wide‐angle X‐ray diffraction and transmission electron microscopy. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1344–1353, 2007     

Nonisothermal cold‐crystallization kinetics of poly(trimethylene terephthalate)

The nonisothermal cold‐crystallization kinetics and subsequent melting behavior of poly(trimethylene terephthalate) (PTT) were investigated with differential scanning calorimetry. The Avrami, Tobin, and Ozawa equations were applied to describe the kinetics of the crystallization process. Both the Avrami and Tobin crystallization rate parameters increased with the heating rate. The Ozawa crystallization rate increased with the temperature. The ability of PTT to crystallize from the glassy state at a unit heating rate was determined with Ziabicki's kinetic crystallizability index, which was found to be about 0.89. The effective energy barrier describing the nonisothermal cold‐crystallization process of PTT was estimated by the differential isoconversional method of Friedman and was found to range between about 114.5 and 158.8 kJ mol^?1. In its subsequent melting, PTT exhibited double‐melting behavior for heating rates lower than or equal to 10 °C min^?1 and single‐melting behavior for heating rates greater than or equal to 12.5 °C min^?1. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4151–4163, 2004     

Nonisothermal crystallization kinetics and spherulite morphology of poly(trimethylene terephthalate)

The nonisothermal melt crystallization behavior of poly(trimethylene terephthalate) (PTT) was investigated using the DSC technique. PTT peak exothermic crystallization temperature was found to move to lower temperatures as the cooling rate was increased. The modified Avrami equation exponent, n, was 4 when the cooling rates were between 5 and 15 °C/min, indicating a thermal nucleation and a three-dimensional spherical growth mechanism. When the cooling rate was increased to 25 °C/min, n gradually decreased to near 3, implying the nucleation mechanism changed to an athermal mode. PTT nonisothermal crystallization behavior could also be analyzed using the Ozawa equation and the combined equations of Ozawa and Avrami with very good fit of the data.PTT spherulite morphologies and the sign of the birefringence depended strongly on the spherulite's growth temperature. When the growth temperature was decreased from 222 to 170 °C, the spherulite changed from a saturation-type dendritic morphology to one with a colorful banded texture; the sign of the birefringence also changed in the following order: from a weakly positive spherulite → mixed spherulite → weakly negative spherulite → negative spherulite → positive spherulite → negative spherulite → positive spherulite.     

Isothermal and nonisothermal crystallization kinetics of poly(propylene terephthalate)

The kinetics of crystallization of poly(propylene terephthalate) (PPT) samples of different molecular weights were studied under both isothermal and nonisothermal conditions. The Avrami and Lauritzen–Hoffmann treatments were applied to evaluate kinetic parameters of PPT isothermal crystallization. It was found that crystallization is faster for low‐molecular‐weight samples. The modified Avrami equation, and the combined Avrami–Ozawa method were found to successfully describe the nonisothermal crystallization process. Also, the analysis of Lauritzen–Hoffmmann was tested and it resulted in values close to those obtained with isothermal crystallization data. The nonisothermal kinetic data were corrected for the effect of the temperature lag and shifted alone with the isothermal kinetic data to obtain a single master curve, according to the method of Chan and Isayev, testifying to the consistency between the isothermal and corrected nonisothermal data. A new method for ranking of polymers, referring to the crystallization rates, was also introduced. This involved a new index that combines the maximum crystallization rate observed during cooling with the average crystallization rates over the temperature range of the crystallization peak. Furthermore, the effective energy barrier of the dynamic process was evaluated with the isoconversional methods of Flynn and Friedmann. It was found that the energy barrier is lower for the low‐molecular‐weight PPT. The effect of the catalyst remnants on the crystallization kinetics was also investigated and it was found that this is significant only for low‐molecular‐weight samples. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3775–3796, 2004     

Thermal and crystallization characteristics of poly(trimethylene terephthalate)/poly(ethylene naphthalate) blends

Poly(trimethylene terephthalate) (PTT)/poly(ethylene naphthalate) (PEN) blends were miscible in the amorphous state in all of the blend compositions studied, as evidenced by a single, composition-dependent glass transition temperature (T_g) observed for each blend composition. The variation in the T_g value with the blend composition was well predicted by the Gordon-Taylor equation, with the fitting parameter being 0.57. The cold-crystallization peak temperature decreased with increasing PTT content, while the melt-crystallization peak temperature decreased with increasing amount of the minor component. The subsequent melting behavior after both cold- and melt-crystallization exhibited melting point depression, in which the observed melting temperatures decreased with increasing amount of the minor component. During melt-crystallization, both components in the blends crystallized concurrently just to form their own crystals. The blend with 60% w/w of PTT exhibited the lowest total apparent degree of crystallinity.     

Crystallization kinetics of poly(trimethylene terephthalate)

The isothermal crystallization kinetics of poly(trimethylene terephthalate) (PTT) have been investigated using differential scanning calorimetry (DSC) and polarized light microscopy (PLM). Enthalpy data of exotherm from isothermal crystallization were analyzed using the Avrami theory. The average value of the Avrami exponent, n, is about 2.8. From the melt, PTT crystallizes according to a spherulite morphology. The spherulite growth rate and the overall crystallization rate depend on crystallization temperature. The increase in the spherulitic radius was examined by polarized light microscopy. Using values of transport parameters common to many polymers (U* = 1500 cal/mol, T_∞= T_g − 30 °C) together with experimentally determined values of T (248 °C) and T_g (44 °C), the nucleation parameter, k_g, for PTT was determined. On the basis of secondary nucleation analyses, a transition between regimes III and II was found in the vicinity of 194 °C (ΔT ≅ 54 K). The ratio of k_g of these two regimes is 2.1, which is very close to 2.0 as predicted by the Lauritzen–Hoffman theory. The lateral surface‐free energy, σ = 10.89 erg/cm² and the fold surface‐free energy, σ_e = 56.64 erg/cm² were determined. The latter leads to a work of chain‐folding, q = 4.80 kcal/mol folds, which is comparable to PET and PBT previously reported. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 934–941, 2000     

Thermal,crystallization, mechanical,and rheological characteristics of poly(trimethylene terephthalate)/poly(ethylene terephthalate) blends

Blends of poly(trimethylene terephthalate) (PTT) and poly(ethylene terephthalate) in the amorphous state were miscible in all of the blend compositions studied, as evidenced by a single, composition‐dependent glass‐transition temperature observed for each blend composition. The variation in the glass‐transition temperature with the blend composition was well predicted by the Gordon–Taylor equation, with the fitting parameter being 0.91. The cold‐crystallization (peak) temperature decreased with an increasing PTT content, whereas the melt‐crystallization (peak) temperature decreased with an increasing amount of the minor component. The subsequent melting behavior after both cold and melt crystallizations exhibited melting point depression behavior in which the observed melting temperatures decreased with an increasing amount of the minor component of the blends. During crystallization, the pure components crystallized simultaneously just to form their own crystals. The blend having 50 wt % of PTT showed the lowest apparent degree of crystallinity and the lowest tensile‐strength values. The steady shear viscosity values for the pure components and the blends decreased slightly with an increasing shear rate (within the shear rate range of 0.25–25 s^?1); those of the blends were lower than those of the pure components. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 676–686, 2004     

Nonisothermal crystallization behavior, and morphology of poly(trimethylene terephthalate)/polyethylene glycol copolymers

Poly(trimethylene terephthalate)/polyethylene glycol (PTT/PEG) copolymers, with PEG content ranging from 27.2 to 47.4 wt%, were synthesized by melt copolycondensation. Wide-Angle X-ray diffractometer revealed that all copolymers had the same crystal structure of homo-PTT at room temperature. All copolymers could form ring-banded spherulites, and band spacing increased with increasing PEG content at a given crystallization temperature. Nonisothermal crystallization morphology of copolymers was greatly influenced by cooling rate. When the cooling rate was 2.5 °C/min or lower, banded patterns were absent, whereas when the cooling rate was 20 °C/min or higher, a novel crystal morphology composed of non-banded spherulites (central part) and ring-banded spherulites with decreasing band spacing along the radial growth direction was observed. Moreover, the size of the non-banded spherulitic part decreased with increasing cooling rate. Finally, the nonisothermal crystallization kinetics of copolymers were analyzed and only the Mo method was satisfactory to accurately describe this system.     

Isothermal crystallization kinetics of poly(ethylene terephthalate)s of different molecular weights

The isothermal crystallization kinetics and morphology of poly(ethylene terephthalate) (PET) polymers of different molecular weights have been studied by means of differential scanning calorimetry and transmission microscopy (TM). The kinetic parameters of Avrami exponent n, the rate constant k, half time t _1/2, rate at 50 % crystallinity, τ _1/2 for crystallization of different PETs were evaluated from double logarithmic plots of log {?ln[1 ? X(t)]} versus log t, where X(t) is extent of crystallinity at a given crystallization temperature. The crystallization rate of polymers with high molecular weight found to be lower than that of polymers with low molecular weight, at the same crystallization temperature. It was found that the nucleation mechanism and growth dimension of polymers with low molecular weight are different from those of polymers with high molecular weight. The results of TM and isothermal crystallization kinetics showed a consistent trend for the crystallization of all PET polymers studied, comprising a primary stage and a secondary stage. The activation energy in the PET polymers of low molecular weight was found to be lower than that of polymers with high molecular weight.     

Phase structure of electrospun poly(trimethylene terephthalate) composite nanofibers containing carbon nanotubes

Nanofibrous composite mats were prepared by electrospinning of poly(trimethylene terephthalate), PTT, with multi-walled carbon nanotubes (PTT/MWCNT). Trifluoroacetic acid (TFA) and methylene chloride (MC) with volume ratio of 50/50 is a good solvent for PTT and was used as the electrospining solution. Scanning electron microscopy was used to investigate the morphology of electrospun (ES) nanofibers with 0, 0.2, 1.0, or 2.0 wt% of MWCNTs. Crystal structure of the ES mats was determined from wide angle X-ray diffraction. Thermal properties were investigated using heat capacity measurements from differential scanning calorimetry (DSC) using the three-runs method for baseline correction, heat flow amplitude calibration, and sample heat capacity determination. A model comprising three phases, a mobile amorphous fraction (MAF), rigid amorphous fraction (RAF), and crystalline fraction (C), is appropriate for ES PTT/MWCNT fibers. The phase fractions, W _i (for i = RAF, MAF or C) were determined by DSC. Crystallinity decreases very slightly with the amount of MWCNT. At the same time, a large increase in RAF was observed: W _RAF of PTT fiber with 2% MWCNT is twice that of neat PTT fiber. The addition of MWCNTs enhanced the PTT chain alignment and increased RAF as a result. Changes of vibrational band absorbance at 1358 and 1385 cm⁻¹, corresponding to characteristic groups, were obtained with infrared spectroscopy. The increased absorbance at 1358 cm⁻¹ and decreased absorbance at 1385 cm⁻¹, with the addition of MWCNTs, strongly supports the three-phase model for ES PTT/MWCNT nanocomposites.     

Morphology,crystallization and melting behaviour of poly(trimethylene terephthalate)/thermotropic liquid crystalline polymer blends

The miscibility, crystallization and melting behaviour of poly(trimethylene terephthalate)/thermotropic liquid crystalline polymer (LCP) blends were studied using differential scanning calorimetry. The blends were found to form primarily an immiscible system. The addition of LCP accelerated the overall rate of crystallization and caused a depression in equilibrium melting temperature, especially at low LCP content. Lauritzen–Hoffman analysis showed that the addition of LCP caused a reduction in the fold surface energy and increased the regime II to III transition temperature.