Simultaneous determination of trace amounts of cadmium, nickel and cobalt in water samples by adsorptive voltammetry using ammonium 2-amino-cyclopentene dithiocarboxylate as a chelating agent

This paper reports the use of an adsorptive voltammetric technique for the simultaneous detection of Cd(II), Ni(II) and Co(II) using ammonium 2-amino-cyclopente dithiocarboxylate as a selective complexing agent. Scans containing three resolved peaks corresponding to these metals were obtained in synthetic and real samples. The reduction current peaks of the metals that were distinctly separated by 200 mV or more, allowing their determination over a wide range of concentrations. These metals can be quantified at concentrations above 1.33x10(-8) mol dm(-3) Cd(II), 8.51x10(-9) mol dm(-3) Ni(II) and 3.39x10(-10) mol dm(-3) Co(II). The influence of pH, ligand concentration, scan rate, accumulations time and applied potential was investigated. The R.S.D. at a concentration level of 1.78x10(-7) mol dm(-3) of Cd(II), 3.40x10(-7) mol dm(-3) and Ni(II) and 1.7x10(-9) mol dm(-3) of Co(II) was 2.5% for Cd(II), 2.7% for Ni(II) and 3.3% for Co(II). The method was applied to various water samples.     

Magnetic solid-phase extraction to preconcentrate trace amounts of gold (III) using nickel ferrite magnetic nanoparticles

In this research, nickel ferrite (NiFe₂O₄) magnetic nanoparticles were synthesised by a simple method and applied as sorbent for magnetic solid-phase extraction of trace amounts of Au(III) from water samples. Detection in this technique was performed by flame atomic absorption spectrometry. The effects of sample pH, amount of sorbent, extraction time, desorption solvent and its volume on the extraction process were optimised. The effects of interfering ions on the recovery of the analyte were also evaluated in model solutions. The best results were obtained at pH 6.5 with 5 mL of eluent solution (0.1 mol L^?1 sodium thiosulphate) and an extraction time of 30 min. Under optimal conditions, the sorption capacity was 34.6 mg g^?1. Also, enhancement factor (for 100 mL of sample solution) was found to be 19.3. The calibration graph was linear in the range of 4.4–800.0 µg L^?1 gold concentration and the limit of detection was 1.32 µg L^?1. The relative standard deviation of the method (for n = 8) was 1.57%. The method was successfully applied to the extraction of Au(III) from water samples.     

2,2′-Dihydroxybenzophenone thiosemicarbazone as a spectrophotometric reagent for the determination of copper,cobalt, nickel,and iron trace amounts in mixtures without previous separations

2,2′-Dihydroxybenzophenone thiosemicarbazone forms complexes with Cu(II) (λ_max = 385 nm, ? = 8.60 × 10³ liter · mol^?1 · cm^?1); Ni(II) (λ_max = 380 nm, ? = 15.4 × 10³ liter · mol^?1 · cm^?1); Co(II) (λ_max = 380 nm, ? = 12.3 × 10³ liter · mol^? · cm^?1); and Fe(III) (λ_max = 365 nm, ? = 7.9 × 10³ liter · mol^?1 · cm^?1) and have been applied to the analysis of these metal ions in binary, ternary, and quaternary mixtures. The determination procedures are based exclusively on the different pH values of the formation complexes, hence the extraction step is not necessary.     

偏最小二乘分光光度法同时测定痕量铁、锰、铜、锌、钴和镍

痕量Fe^3 ,Mn^2 ,Cu^2 ,Zn^2 ,Co^2 ,Ni^2 与2－（5－溴－2－吡啶偶氮）－5－二乙氨基苯酚（5－Br-PADAP)和溴化十六烷基三甲基铵（CTMAB）在PH8．3时发生高灵敏显色反应，所形成的三元胶束络合的吸收光谱严重重叠，采用偏最小二乘法（PLS）辅助分光光度法测定了合成试样及饲料中上述6种痕量组分，结果表明，PLS法是化学计量学中一种可适用于基体较复杂的实际试样中痕量组分分光度同时测定的多元计算方法。     

锌电解液中痕量铜、镉、镍和钴的快速同时测定

研究了丁二酮肟 氨 氯化铵 柠檬酸钠 明胶 抗坏血酸体系中Cu(Ⅱ )、Cd(Ⅱ )、Ni(Ⅱ )和Co(Ⅱ )的络合物吸附波 ,建立了同时、快速测定锌电解溶液中这些痕量元素的新方法。Cu(Ⅱ )、Cd(Ⅱ )、Ni(Ⅱ )和Co(Ⅱ )分别在 - 0 44V、- 0 76V、- 1 0 7V和 - 1 2 4V左右产生灵敏的络合物吸附波。信噪比为 3时 ,其检测限分别为 1 0× 1 0 - 8mol/L、1 3× 1 0 - 8mol/L、2 9× 1 0 - 1 0 mol/L和 3 6×1 0 - 1 1 mol/L。铜、镉、镍和钴的浓度分别为 2 0× 1 0 - 8mol/L～ 2 0× 1 0 - 5 mol/L、3 0× 1 0 - 8mol/L～ 3 0× 1 0 - 5mol/L、5 4× 1 0 - 1 0 mol/L～ 5 4× 1 0 - 7mol/L和 6 8× 1 0 - 1 1 mol/L～ 6 8× 1 0 - 8mol/L时 ,与相应峰电流之间有良好的线性关系。方法已用于锌电解液中铜、镉、镍和钴的快速同时测定 ,相对标准偏差分别小于或等于 4 7%、5 1 %、4 9%和 5 3 %。     

Simultaneous determination of iron, cobalt, nickel and copper by UV-visible spectrophotometry with multivariate calibration

A method for the simultaneous spectrophotometric determination of the divalent ions of iron, cobalt, nickel and copper based on the formation of their complexes with 1,5-bis(di-2-pyridylmethylene) thiocarbonohydrazide (DPTH) is proposed. The resolution of quaternary mixtures of these metallic ions was accomplished by several chemometric approaches. A comparative study of the results obtained for simultaneous determinations in mixture by using principal component regression (PCR) and partial least-squares regression (PLS-1 and PLS-2) for absorbance, first-derivative and second-derivative data is presented. In general, the best recovery values are obtained by the PLS-2 method for absorbance data. This procedure allows the simultaneous determination of the cited ions in alloys and biological materials Good reliability of the determination was proved.     

Determination of trace amounts of nickel by differential pulse adsorptive cathodic stripping voltammetry using calconcarboxylic acid as a chelating agent

A method for the determination of nickel(II) by stripping voltammetry is described. The method is based on the adsorptive accumulation of nickel(II) calconcarboxylic acid complex onto a hanging mercury drop electrode (HMDE), followed by the reduction of the adsorbed complex using differential pulse voltammetry. The optimum operating conditions and parameters were found to be 0.05 M NH₃/NH₄Cl buffer (pH = 9.5) as the supporting electrolyte, a ligand concentration of 1 × 10^?6 M, accumulation potential of ?0.5 V (vs. Ag/AgCl) and accumulation time of 60 s. At the optimized conditions, the peak current is proportional to the concentration of nickel in the range of 1.7 × 10^?9 to 4.7 × 10^?7 M (0.1–28 ng ml^?1) with a detection limit of 0.05 ng ml^?1. The relative standard deviation (n = 10) at nickel concentrations of 2, 10 and 15 ng ml^?1 varies in the range 0.76 to 2.1%. Possible interferences by metal ions, which are of great significance in real matrices, have been studied. The method was successfully applied to the determination of nickel content in a chocolate sample.     

Flotation-separation and ICP-AES determination of ultra trace amounts of copper, cadmium, nickel and cobalt using 2-aminocyclopentene-1-dithiocarboxylic acid.

A rapid flotation method for separation and enrichment of ultra trace amounts of copper(II), cadmium(II), nickel(II) and cobalt(II) ions from water samples is established. At pH 6.5 and with sodium dodecylsulfate used as a foaming reagent, Cu2+, Cd2+, Ni2+ and Co2+ were separated simultaneously with 2-aminocyclopentene-1-dithiocarboxylic acid (ACDA) added to 1 l of aqueous solution. The proposed procedure of preconcentration is applied prior to the determination of these four analytes using inductivity coupled plasma-atomic emission spectrometry (ICP-AES). The effects of pH, concentration of ACDA, applicability of different surfactants and foreign ions on the separation efficiency were investigated. The preconcentration factor of the method is 1000 and the detection limits of copper(II), cadmium(II), nickel(II) and cobalt(II) ions are 0.078, 0.075, 0.072 and 0.080 ng ml(-1), respectively.     

Simultaneous spectrophotometric determination of trace amounts of cobalt, nickel, and copper using the partial least-squares method after the preconcentration of their 2-aminocyclopentene-1-dithiocarboxylate complexes on microcrystalline naphthalene

A spectrophotometric method for the determination of trace amounts of cobalt(II), nickel(II), and copper(II) after the adsorption of their 2-aminocyclopentene-1-dithiocarboxylate complexes on microcrystalline naphthalene has been developed. These complexes are adsorbed on microcrystalline naphthalene at pH 4.5 by shaking for 5 min. The formed solid mass is separated by filtration, and dissolved in dimethylformamide. The absorption spectra were processed using the partial least-squares multivarate calibration method for the analysis of a ternary mixture of Co(II), Ni(II), and Cu(II). The detection limits for Co(II), Ni(II), and Cu(II) were 3.3, 10.0, and 0.8 ng/mL, respectively. The total relative standard error for applying the method to 20 synthetic samples in the concentration ranges of 20–400 ng/mL Co(II), 60–400 ng/mL Ni(II), and 4–400 ng/mL Cu(II) was 1.53%. The proposed method was also successfully applied to the determination of Co(II), Ni(II), and Cu(II) in alloys. The text was submitted by the authors in English.     

Simultaneous determination of cobalt,nickel and iron by multi-wavelength spectrophotometry

A method for the simultaneous spectrophotometric determination of cobalt, nickel and iron based on the formation of their complexes with 1,5-bis(di-2-pyridylmethylene) thiocarbonohydrazide is proposed. The absorption curves of these complexes overlap severely in the scanning range 390–510 nm. The analyte concentrations are calculated by a least squares fit of the pure spectra to the mixture spectra, which therefore makes the simultaneous determination of these metallic ions possible without tedious pretreatment. The detection limits afforded by the proposed method range from 0.05 g/ml for Fe and Ni to 0.1 g/ml for Co. Root-mean-squared errors of prediction of 0.085 g/ml for Co, 0.048 g/ml for Ni and 0.1172 g/ml for Fe were obtained using the wavelength range 400–510 nm and 0.147 g/ml for Co, 0.107 g/ml for Ni and 0.127 g/ml for Fe using the wavelength range 420–434 nm. The effect of interferences is studied and the proposed method is applied to analysis for the above elements in synthetic samples and real samples, such as biological materials and alloys.     

Simultaneous determination of trace amounts of nickel, cobalt, and zinc in the wastewater of a galvanic workshop by using adsorptive cathodic stripping voltammetry

Electroplating of Ni, Co, and Zn is widely used in the industry, because coating of tools with these materials can improve mechanical and chemical properties such as hardness, toughness, and corrosion resistively. Ni, Co, and Zn are among toxic metals of significance for environmental surveillance. Therefore, determination of these elements in wastewater is very important. This paper reports the use of an adsorptive cathodic stripping voltammetric technique for the simultaneous determination of Ni(II), Co(II), and Zn(II) with dimethylglyoxime (DMG) as a chelating agent. Voltammograms of Ni(II), Co(II), and Zn(II) initially contained three peaks corresponding to these metals. However, the peaks overlapped. Therefore, the effect of organic solvents was studied, and the results showed that the use of a suitable ratio of ethanol-water (1:5) solvent and pH provided peaks that were distinctly separated. The metals can be quantified at concentrations above 0.03 (Ni), 0.02 (Co), and 0.1 μg/mL (Zn). The RSD (%) at concentration levels of 0.10 μg/mL Ni(II), 0.10 μg/mL Co(II), and 0.30 μg/mL Zn(II) is 2.3, 2.0, and 3.3%, respectively. The influence of pH, DMG concentration, scan rate, accumulations time, and potential was investigated. The method was satisfactorily used for determination of the metals under study in water and wastewater. The text was submitted by the authors in English.     

Micellar colorimetric determination of iron, cobalt, nickel and copper using 1-nitroso-2-naphthol

1-Nitroso-2-naphthol, an excellent color-forming chelating agent, combines to Fe(III), Co(II), Ni(II), Cu(II) and so on to form slightly soluble complexes in aqueous solution. To determine these metal ions, a tedious and time consuming separation technique, such as liquid-liquid extraction, has often been performed. However, these metal-1-nitroso-2-naphthol complexes could be determined conveniently by ultraviolet-visible (UV-Vis) spectrophotometry in Tween 80 micellar medium that has polyoxyethylene groups. After conditions such as pH, the amount of 1-nitroso-2-naphthol and the stability were adjusted to their optimum values, the sensitivities of the metal ions in Tween 80 medium and in chloroform were compared. It was shown that the sensitivities of Fe(III) and Co(II) in Tween 80 medium were higher than in chloroform, but that of Cu(II) was lower. The interfering effects among analytes ions, Fe(III), Co(II), Ni(II) and Cu(II) were more serious than by other ions, but the interfering effects could be removed by adjusting pH or adding the masking agents such as NH(3) or oxalate. Detection limits of Fe(III), Co(II), Ni(II), and Cu(II) were 0.024, 0.016, 0.039 and 0.023 mug ml(-1), respectively, and the correlation coefficients of these calibration curves were above 0.996. Recovery yields of the metal ions in the mixed standard solution ranged from 96 to 103%, and their coefficients of variation were low ranging between 0.94 and 1.75%. Cu(II) in brass sample and the amount of Fe(III) in steel sample were also determined. This proposed technique is simple, convenient and speedy.     

Simultaneous preconcentration of copper, nickel, cobalt and lead ions prior to their flame atomic absorption spectrometric determination

A sensitive and simple method for the simultaneous preconcentration of nutritionally important minerals in real samples has been reported. The method is based on the adsorption of Cu2+, Ni2+, Co2+ and Pb2+ on 4-propyl-2-thiouracil (PUT) loaded on activated carbon. The metals on the complexes are eluted using 5 mL 3 M HNO3 in acetone. The influences of the analytical parameters including pH and sample volume were investigated. The effects of matrix ions on the retentions of the analytes were also examined. The recoveries of analytes were generally higher than 95%. The detection limits for Cu2+, Ni2+, Co2+ and Pb2+ were 1.6, 1.3, 1.2, 2.3 ng ml(-1), respectively. The method has been successfully applied for these metals content evaluation in some real samples including natural water samples.     

Determination of trace amounts of lead, arsenic, nickel and cobalt in high-purity iron oxide pigment by inductively coupled plasma atomic emission spectrometry after iron matrix removal with extractant-contained resin

Inductively coupled plasma atomic emission spectrometry (ICP-AES) was applied to the determination of lead, arsenic, nickel and cobalt in high-purity iron oxide pigment. Samples were dissolved with hydrochloric acid and hydrogen peroxide. The digest was passed through a column, which was packed with a polymer resin containing a neutral organophosphorus extractant, tri-n-butylphosphate. Iron was sorbed selectively on the resin and the analytes of interest passed through the column, allowing the effective separation of them from the iron matrix. Conditions of separation were optimized. The detection limits (3σ) in solution were 10, 40, 7 and 5 μg L⁻¹, and in pigment were 0.2, 0.8, 0.14 and 0.1 mg kg⁻¹ for lead, arsenic, cobalt and nickel, respectively. The recoveries ranged from 95% to 107% when sample digests were spiked with 5 μg of the analytes of interest, and relative standard deviations (n = 6) were 1.5-17.6% for the determination of the spiked samples. The method was successfully applied to the determination of trace amounts of these elements in high-purity iron oxide pigment samples.     

Separation of large amounts of iron(III) from cobalt,nickel, and aliminum by combined ion exchange-solvent extraction

A method is described for the cation-exchange separation of large amounts of iron(III) from cobalt, nickel, and aluminium. On the strongly acidic Dowex 50-X8, iron(III) is not adsorbed from an 80% tetrahydrofuran-20% 3 M hydrochloric acid mixture, while cobalt, nickel, and aluminium are retained; a quantitative separation is thus possible. Cobalt and nickel or aluminium are then separated by elution with 90% tetrahydrofuran-10% 6 M hydrochloric acid. In these mixtures combined ion exchange-solvent extraction appears to occur; both ion exchange and liquid-liquid extraction are. effective simultaneously.     

Spectrophotometric determination of copper, nickel, cobalt, iron and manganese as their pyridine thiocyanates Simultaneous determination in mixtures

Spectrophotometric determinations of copper, nickel, cobalt, iron, and manganese, based on the chloroform extraction of the metal pyridine thiocyanates, have been investigated. Optimum conditions require the pH of the aqueous solution to be in the range about 5–8; tartaric acid is used to prevent precipitation of hydrous oxides. An excess of pyridine must be used because chloroform readily extracts pyridine from the aqueous solution. Results are improved by making the extraction from a solution of high ionic strength (2 or above), which is provided by magnesium nitrate. Perchlorate decreases the absorbance, but the effect is essentially constant over a perchlorate concentration range of 0.8 to 2M. Although the metal pyridine thiocyanates are extracted by benzene, substituted benzenes, and halogenated hydrocarbons, chloroform is superior to other solvents in extraction efficiency and in colour stability of the extracted species. An example is given of the simultaneous determination of copper, nickel, cobalt, and iron in the same solution. Anions that also form metal pyridine compounds must be absent.     

Simultaneous determination of trace amounts of anti-hypertensive drugs in urine using magnetic mixed hemimicelles solid-phase extraction combined with HPLC-UV

Hypertension is the leading cause of morbidity and mortality in developed and developing countries. The combination of amlodipine and carvedilol is very effective for reducing blood pressure and improving treatment compliance. Determination of drugs in biological fluids is vital in therapeutic efficacy. In the present study, a simple, rapid and efficient magnetic solid phase extraction procedure based on mixed hemimicelles is described and validated for the simultaneous determination of trace amounts of anti-hypertensive drugs in urine samples using sodium dodecyl sulfate-coated magnetite nanoparticles as extractant. Various factors, which could affect the extraction efficiency were investigated and optimized. Under the optimum conditions, the limits of detection (S/N = 3) for amlodipine and carvedilol were 5 and 2 ng/mL, respectively. The relative standard deviation for six measurements of 50 ng/mL of amlodipine and carvedilol were 4.7 and 5.2%, respectively. The developed method was applied to the analysis of patients' urine samples, and satisfactory results were obtained in the range between 81.6 and 92.7%.     

Mechanism of carbothermal reduction of iron, cobalt, nickel and copper oxides

A new scheme of thermal dissociation which is based on the dissociative evaporation of the reactant with simultaneous condensation of the low-volatile product has been invoked to interpret the kinetics of reduction of FeO, CoO, NiO and Cu₂O by carbon. A critical analysis of literature data and their comparison with theoretical calculations has shown that the main kinetic characteristics of carbothermal reduction, including the initial decomposition temperature and activation energy are in full agreement with the proposed mechanism of decomposition. Condensation of the low-volatile product (metal vapour) in the reaction zone and partial transport of condensation energy to the oxide account for the features which are typical of solid state reactions and manifest themselves in the appearance of periods of induction and acceleration in the course of the process. Carbon fulfils the role of buffer in this process. This is supported by an appearance of metals in the condensed phase and a higher than equilibrium partial pressure of oxygen in high-vacuum experiments with Knudsen cells.     

Solid-phase extraction of trace metal ions with magnetic nanoparticles modified with 2,6-diaminopyridine

We have modified silica-coated Fe₃O₄ nanoparticles with 2,6-diaminopyridine and used these for selective magnetic solid-phase extraction of trace amounts of metal ions. The nanoparticles were characterized by transmission electron microscopy and Fourier transform infrared spectroscopy. Quantitative extraction of trace amounts of Cu(II) and Zn(II) from mixed-ion solutions was accomplished at an optimal pH value of 6 within less than 10?min. The metal ions were eluted from the sorbent with hydrochloric acid. Common electrolytes and chemically related metal ions do not interfere. The relative standard deviations of the method are <4?%. It was successfully applied to the separation and preconcentration of trace metal ions from the certified reference materials GBW 08301 (river sediment) and GBW 08607 (water solution), in natural water, and in samples of vegetable with satisfying results.