Electrical and electro-chemical characterisation of La0.99Fe1−x Ni x O3−δ perovskites

(LFN, 0<x<0.6) perovskites were synthesised by a solid-state route and were characterised by powder XRD, dilatometry, four-point DC conductivity measurements and electro-chemical impedance spectroscopy (EIS) on cone-shaped electrodes using a Ce_1.9Gd_0.1O_1.95 (CGO10) electrolyte. All the compounds were of single phase, and they belong to either the cubic or the hexagonal crystal system. The thermal expansion coefficient (TEC) was in the range 10.7*10⁻⁶ K⁻¹ to 13.4*10⁻⁶ K⁻¹, which continued to increase with increasing nickel content. The highest electronic conductivity was measured for the composition giving a value of 670 S/cm at 380 °C. The highest electro-chemical performance was measured for the composition giving an area specific resistance as low as 5.5 Ωcm² at 600 °C based on EIS measurements on a cone-shaped electrode. Composite cathodes made from and CGO10 revealed a rather low performance due to an un-optimised micro-structure.

---

Mixed valence states of Cr and Fe in La1−xSrxFe0.8Cr0.2O3−y

The La_1?xSr_xFe_0.8Cr_0.2O_3?y (x = 0.2, 0.4, 0.6 and 0.8) phases were studied by X-ray photoelectron spectroscopy at room temperature and ⁵⁷Fe Mössbauer spectroscopy at different temperatures. Mixed valence states were observed both for chromium and iron ions, justifying the complex magnetic behaviour exhibited by these compounds. The Mössbauer results indicate the simultaneous presence of Fe³⁺, Fe⁴⁺ and Fe⁵⁺ at 4.2 K and the co-existence of Fe³⁺ and Fe⁽³⁺ⁿ⁾⁺ at T = 293 K, with the latter fraction increasing with increasing strontium content. The presence of Cr^3+/4+ is interpreted as being mainly responsible for the incomplete charge disproportionation reaction of iron at low temperature, as deduced from the Mössbauer results.     

Mechanical properties of mixed conducting La0.5Sr0.5Fe1−x Co x O3−δ (0≤x≤1) materials

Young’s modulus, strain–stress behavior, fracture strength, and fracture toughness of (0≤×≤1) materials have been investigated in the temperature range 20–1,000°C. Young’s moduli of and , measured by resonant ultrasound spectroscopy, were 130±1 and 133±3 GPa, respectively. The nonlinear stress–strain relationship observed by four-point bending at room temperature was inferred as a signature of ferroelastic behavior of the materials. Above the ferroelastic to paraelastic transition temperature, the materials showed elastic behavior, but due to high-temperature creep, a nonelastic respond reappeared above ∼800°C. The room temperature fracture strength measured by four-point bending was in the range 107–128 MPa. The corresponding fracture toughness of , measured by single edge V-notch beam method, was 1.16±0.12 MPa·m^1/2. The measured fracture strength and fracture toughness were observed to increase with increasing temperature. The fracture mode changed from intragranular at low temperature to intergranular at high temperature. Tensile stress gradient at the surface of the materials caused by a frozen-in gradient in the oxygen content during cooling was proposed to explain the low ambient temperature fracture strength and toughness.     

Electroconductivity and nature of ion transfer in La1 − x Sr x Sc1 − y Mg y O3 − α system (0.01 ≤ x = y ≤ 0.20) in dry and humid air

The conductivity and ion and proton transfer numbers were measured in La_{1 ? x} Sr _x Sc_{1 ? y} Mg _y O_{3 ? α} system (x = y = 0.10–0.20). The partial conductivities (total ion, proton, oxygen, hole) and their effective activation energies were calculated. The measurements were carried out in air with respect to humidity (pH₂O = 0.04?2.65 kPa) within the temperature range from 630 to 920°C.     

Weakly bound oxygen and its role in stability of solid solutions La1−x Sr x FeO3−δ

In the present study high-temperature X-ray diffraction, thermal analysis, and mass-spectrometry have been employed for investigation of samples in the La_1?x Sr _x FeO_3?δ family (0 ≤ x ≤ 1), the materials being solid solutions having perovskite structure. It has been shown that the loss of oxygen by the samples on heating to 1200°C in air (0 ≤ x ≤ 1) or in vacuum (x < 0.75) does not result in structural rearrangement of the solid solutions, but causes an increase in the lattice parameters. Heating of the compositions with x ≥ 0.75 in vacuum affords phases with ordered vacancies. The observed structural evolutions (growth of the unit cell parameter and vacancy ordering) are reversible, and on re-oxidation (on cooling in air or additional heating of the “vacuum” samples in air atmosphere) the original parameters of the oxides are recovered. The amount of oxygen evolved on heating increases in vacuum or in helium atmosphere, as compared to air, and also grows with rising strontium content, but under experimental conditions does not reach the maximum possible value (δ = x/2).     

Synthesis and electrochemical properties of nanosized carbon-coated Li1−3x La x FePO4 composites

Nanosized carbon-coated Li_1−3x La _x FePO₄ composites were synthesized using a fast, easy, microwave assisted, room-temperature, solid-state method. A lanthanum precursor was used to improve the electronic conductivity of LiFePO₄. The particle structure of the as-synthesized samples was observed using transmission electron microscopy. The results indicated that a uniform and continuous carbon layer was formed on the surface of Li_1−3x La _x FePO₄ particles. Electrochemical techniques, such as cyclic voltammetry, charge/discharge test, and electrochemical impedance spectroscopy were used to investigate the electrochemical performance of the samples. The results of electrochemical measurements revealed that the carbon coating and lanthanum doping provided an initial discharge capacity of 145 mA h/g with excellent rate capacity and long cycling stability. These advantages, coupled with the low cost, the high thermal stability, and the environmental friendliness of the raw materials, render Li_1−3x La _x FePO₄/C composites attractive for practical and large-scale applications.     

Characterization of superparamagnetic Mg x Zn1−x Fe2O4 powders

Structural and magnetic properties of Mg _x Zn_1−x Fe₂O₄ powders have been studied with respect to the application for thermal cancer therapy (magnetic hyperthermia). Mg _x Zn_1−x Fe₂O₄ (x=0.1–0.5) powders with particle sizes between 5 and 8 nm were produced by citrate method. The X-ray diffraction patterns of the samples correspond to a spinel phase. The lattice constant and the volume of the elementary cell increase when x changes from 0.1 to 0.5. The FTIR-spectra ascertain the spinel phase formation. The Mossbauer studies reveal the presence of extremely small particles, which undergo superparamagnetic relaxation at room temperature. The core-shell model has been applied to explain quadruple doublets. The quadruple splitting at “shells” is bigger than those at “cores” whereas the isomer shifts remain close. Magnetic studies confirm the presence of extremely small particles that behave as superparamagnetic ones.      

Defects in doped perovskite-like lanthanum cobaltite crystals La1−x SrxCo1−y MeyO3−δ (Me = Cu and Mn)

The paper presents a thermodynamic analysis of the formation of equilibrium defects in perovskitelike La_1?x Sr_xCo_1?y Me_yO_3?δ oxides, where Me = Cu or Mn, x = 0.0 or 0.3, and y = 0.0, 0.25, or 0.3, at high temperatures (873 K ≤ T ≤ 1373 K) depending on the composition and oxygen pressure (10^?8 atm ≤ $p_{O_2 } $ ≤ 1 atm). The results were used to study the nature of charge transfer. Small-radius polarons were shown to be responsible for the electric properties of the cobaltites under consideration; their concentrations and mobilities were calculated.     

Forms of oxygen in La1 − x Ca x MnO3 + δ (x = 0–1) perovskites and their reactivities in oxidation reactions

The effects of substitution in the cationic sublattice and of the synthesis procedure on the reactivity of different forms of oxygen in La_{1 ? x} Ca _x MnO_{3 + δ} perovskites synthesized by mechanochemical and ceramic processing was studied by temperature-programmed reduction (TPR) with hydrogen. As the calcium content of the perovskite is raised, the maxima of the TPR peaks shift to lower temperatures and the extent of reduction of the perovskite increase, implying an increase in the reactivity of the system. Conversely, raising the calcination temperature or extending the calcination time shifts the maxima of the peaks to higher temperatures and diminishes the extent of reduction of the sample. TPR data for the intermediate-composition samples can be explained in terms of the dependence of microstructure on the synthesis procedure (near-surface calcium segregation in the mechanochemically synthesized samples and the microheterogeneous structure of the ceramic samples). The reduction process Mn⁴⁺ → Mn²⁺ takes place in the low- and medium-temperature regions. According to the literature, the bulk reduction process Mn³⁺ → Mn²⁺ occurs at high temperatures. The activity of the system in CO oxidation is correlated with the amount of the most reactive surface oxygen, which is eliminated in hydrogen TPR runs below 250–300°C.     

Hydrogen content in proton-conducting perovskites CaZr1 − x Sc x O3 − x /2 (x = 0.0–0.2)

The hydrogen content in CaZr_{1 ? x} Sc _x O_{3 ? x/2} (x = 0.00–0.20) and BaZr_0.9Y_0.1O_3-α (for comparison) was studied by powder nuclear microanalysis. The samples were saturated with heavy water (D₂O) vapors at 350 and 400°C in air. The chemical expansion of the CaZr_0.95Sc_0.05O_3-α and BaZr_0.95Y_0.05O_3-α samples at 700°C was measured at different water vapor pressures. A model was suggested to explain the lowered hydrogen content in oxides based on CaZrO₃.     

Synthesis and photoluminescent properties of Y1 − x La x PO4:Eu3+ nanophosphor

In this paper, Y_{1 ? x} La _x PO₄:Eu³⁺ (x = 0.5, 0.7, and 0.3) nanophosphors were synthesized by a rather simple method. The products present different morphologies. For Y_{1 ? x} La _x PO₄:Eu³⁺, they have similar phase composition of a mixture of monoclinic LaPO₄ and tetragonal YPO₄. Furthermore, the luminescence behavior of Eu³⁺ has been investigated in this type of matrices. In Y_{1 ? x} La _x PO₄:Eu³⁺, the ⁵D₀-⁷F₁ magnetic dipole transition is dominant, indicating that the Eu³⁺ site is inversion symmetry. The difference in the Eu-O charge transfer (CT) band with La³⁺ ion concentration suggests the difference in the ionicity of the Eu-O bond. Among those products, the red to orange intensity ratio (R/O) of ⁵D₀-⁷F₂ to ⁵D₀-⁷F₁ value of Eu³⁺ is different, furthermore, for La³⁺ x = 0.3, the R/O value of Eu³⁺ is the biggest on the contrary, indicating that the inversion symmetry Eu³⁺ is lowest.     

Novel red-emitting phosphors, (Mg(1−x−y)MnxDyy)Al2Si2O8 and (Mg(1−x−y)MnxTmy)Al2Si2O8

Mn⁴⁺ doped and Dy³⁺, Tm³⁺ co-doped MgAl₂Si₂O₈-based phosphors were prepared by conventional solid state reaction at 1,300 °C. They were characterized by thermogravimetry, differential thermal analysis, X-ray powder diffraction, photoluminescence, and scanning electron microscopy. The luminescence mechanism of the phosphors, which showed broad red emission bands in the range of 600–715 nm and had a different maximum intensity when activated by UV illumination, was discussed. Such a red emission can be attributed to the ²E → ⁴A₂ transitions of Mn⁴⁺.     

Longitudinal conductivity of thin films of La1 − x Sr x F3 − x solid solutions on glass ceramics

The longitudinal conductivity of La_{1 ? x} Sr _x F_{3 ? x} solid solution films (x = 0–0.24) with thicknesses of 40–260 nm grown on glass ceramics at temperatures from room temperature to 300°C and frequencies of 10^?1–10⁶ Hz was studied by impedance spectroscopy. The concentration dependence of film conductivity on the SrF₂ content had a maximum near x = 0.05. An equivalent circuit was constructed on the basis of the impedance plots to describe migration processes. The DC conductivity was evaluated for all samples under study. The activation energies were estimated from the temperature dependences of the DC conductivities of the films. The resulting dependences of electrophysical parameters were compared with those for bulk materials in terms of the relaxation conductivity model.     

Sintering, microstructures and dielectric properties of Ba1−xPbx(Ti1−xLix)O3−3xF3x ferroelectric ceramics

Various compositions (1−x)BaTiO₃ + xPbF2 + xLiF were prepared, shaped to pellets then sintered at 900°C for 2 h in gold sealed tubes. The purity and the symmetry of the obtained samples were checked by X-ray diffraction. A new solid solution with Ba_1−x Pb _x (Ti_1−x Li _x ) O_3−3x F_3x formula occurs in the composition range 0 ≤ x ≤ 0.20. SEM observations were performed on polished and fractured ceramics. The complex permittivity was measured as a function of temperature (−120°C ≤ T ≤ 250°C) and frequency (50 Hz ≤ f ≤ 4 × 10⁷ Hz). The dielectric performances are the best for ceramic Ba_0.97Pb_0.03(Ti_0.97Li_0.03)O_2.91F_0.09. The real component ε′, exhibits a maximum of approximately 7500 at the ferroelectric Curie temperature T _C ≈ -18°C, the dielectric losses tan δ value being 0.012. At room temperature, the relaxation frequency f _r is around 40 MHz for this ceramic. This novel ferroelectric oxifluoride is a promising material for applications, in particular in the field of Z5U multilayer capacitors.      

Glycolate Ti1 − x Fe x (OCH2CH2O)2 − x/2 as a precursor for the preparation of quasi-one-dimensional (1D) solid solutions Ti1 − x Fe x O2 − 2x/2 (0 ≤ x ≤ 0.1)

Quasi-one-dimensional (1D) solid solutions Ti_{1 ? x} Fe _x (OCH₂CH₂O)_{2 ? x/2} (0 < x ≤ 0.1) with the structure of anatase were prepared by heating the glycolate Ti_{1 ? x} Fe _x (OCH₂CH₂O)_{2 ? x/2} in an atmosphere of air at a temperature of >450°C. The conditions of formation and the properties of the new glycolate Ti₃Fe₂(OCH₂CH₂O)₉ were described. It was found that the synthesized Ti_{1 ? x} Fe _x O_{2 ? 2x/2} solid solutions exhibit photocatalytic activity in the reaction of hydroquinone oxidation in an aqueous solution on irradiation with UV light. A correlation between the rate of oxidation of hydroquinone and the concentration of iron in the catalyst was established. A procedure for the preparation of titanium dioxide with the structure of anatase doped with iron and carbon (Ti_{1 ? x} Fe _x O_{(2 ? x/2) ? yCy)} and also composites on its basis, which contain an excess amount of carbon, was proposed.     

Electrochemical reduction of NO and O2 on La2−x Sr x CuO4-based electrodes

A series of La_2 − x Sr _x CuO₄ (x = 0.0, 0.05, 0.15, 0.25 and 0.35) compounds was investigated for the use of direct electrochemical reduction of NO in an all-solid-state electrochemical cell. The materials were investigated using cyclic voltammetry in 1% NO in Ar and 10% O₂ in Ar. The most selective electrode material was La₂CuO₄, which had an activity of NO reduction that was 6.8 times higher than that of O₂ at 400 °C. With increasing temperature, activity increased while selectivity decreased. Additionally, conductivity measurements were carried out, and the materials show metallic conductivity behavior which follows an adiabatic small polaron hopping mechanism.     

Van der Waals Gaps in Sm1+x Ba2−x Cu3O y and Their Effect on Superconductivity

We have used electron–positron annihilation to study superconducting cuprates Sm_1+x Ba_2–x Cu₃O _y . We have determined the average radii for oxygen ions in Sm_1+x Ba_2–x Cu₃O _y . Taking into account the ion coordinates and their radii, we have constructed a geometric model for the arrangement of copper and oxygen ions in CuO₂ layers in the [b, c] plane, responsible for the superconductivity. From these data, we have determined the length of the ionic/covalent bonds and the width of the interionic gaps. We have established the effect of the features of the atomic structure of Sm_1+x Ba_2–x Cu₃O _y on the superconducting transition temperature T _c and we have shown that T _c increases as X inceases.     

Preparation and properties of highly conductive La1−x M x MnO3−y thin film showing magnetic effect from sol-gel process

The sol-gel synthesis of Sr-doped-LaMnO₃ thin film was investigated. The optimum condition was obtained when strontium, lanthanum and manganese nitrates were used as raw materials and diethylene or propylene glycol was used as solvent. An alumina plate was used as a substrate. The film thickness was about 0.2 m for one dip coating. The conductivity of Sr-substituted-LaMnO₃ increased with increasing Sr content and showed ferromagnetic properties. The conduction mechanism was a hopping conduction due to the small polaron. The metal-semiconductor transition at around room temperature was considered to be caused by the Jahn-Teller effect.