Preparation of copper aluminum borate whiskers via flux method

Single‐crystal and uniform copper aluminum borate whiskers have been synthesized by heating a mixture of boric acid, copper sulfate and aluminum sulfate with potassium sulfate as flux at 870 °C for 4 h. The synthesized whiskers exhibit a well‐crystallized, one‐dimensional structure with diameters ranging from 100 nm to 5 μm, lengths from 5 to 100 μm. Heating temperature and flux addition affect the aspect ratio and morphology of the copper aluminum borate whiskers. A possible growth mechanism of the whiskers is proposed. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Synthesis of stoichiometric LiNbO3 nanopowder through a wet chemical method

Stoichiometric lithium niobate powder which are used as feeding material in near stoichometric LiNbO₃ crystal growth have been successfully prepared from commercial niobium hydroxide [Nb(OH)₅] and nontoxic DL‐malic acid by a wet chemical method. The synthesis temperature was pre‐determined by the results from thermogravimetric and differential thermal analysis. The structure and morphology of the as‐prepared samples were observed by using the infrared spectroscopy and the scanning electron microscopy. The X‐ray diffraction experiment showed that lithium niobate powder had an ilmenite structure, and its unit cell parameters were calculated to be a = b = 0.5140 nm, c = 1.3738 nm, and V = 0.3144 nm³. The melting point of the synthesized powder is 1239 °C and Curie temperature T_c is 1122 °C. This synthesis method would be helpful to grow the near‐stoichiometric LiNbO₃ crystal with double crucible techniques. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Preparation of calcium sulfate whiskers by carbide slag through hydrothermal method

In this work, a series of calcium sulfate whiskers were prepared successfully using carbide slag as raw material through hydrothermal method. The prepared gypsum observed is hemihydrate calcium sulfate and the formation of the calcium sulfate whiskers are influenced by preparation parameters. The optimal preparation conditions are as follows: seriflux concentration, 4 %; hydrothermal reaction time, 10 h; hydrothermal reaction temperature, 130°C; seriflux pH, 7; calcium‐magnesium ratio, 12 : 1. Some nanowires appear when seriflux pH is very low (e.g. 1). The length‐diameter ratio of the whiskers is about 60‐80.     

Synthesis and characterization of magnetite nanocrystals

Nanocrystals of magnetite (Fe₃O₄) were prepared by sol‐gel technique. The prepared nanocrystals were characterized for phase by powder X‐ray diffraction (XRD) of the samples annealed at successively higher temperature. The magnetite phase was formed during the annealing of the synthesized powder at 400 °C for a few hours. The Fourier transform infrared spectroscopy (FTIR) was performed to analyze the functional groups in the material. The energy dispersive X‐ray diffraction (EDAX) was performed for chemical composition analysis. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) techniques were used to analyze the morphology of nanocrystals and for estimating their average size. The results confirm the formation of Fe₃O₄nanocrystals of the sizes ∼20–50 nm. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Substrate temperature effect on the optical properties of amorphous Sb2S3 thin films

Sb₂S₃ amorphous thin films were prepared by thermal evaporation of corresponding powder on thoroughly cleaned glass substrates held at temperature in the range 300‐473 K. X‐ray diffraction and atomic force microscopy have been used to order to identify the structure and morphology of surface thin films. The optical constants of the deposition films were obtained from the analysis of the experimental recorded transmission data over the wavelength range 400‐1400 nm. An analysis of the absorption coefficient values revealed an optical indirect transition with the estimation of the corresponding band gap values. It was found that the optical band gap energy decrease with substrate temperature from 1.67 eV at 300 K to 1.48 eV at 473K. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Preparation of crystalline fibres of codoped BaAl2O4:Eu2+:Cr3+

Phosphor material BaAl₂O₄:Eu²⁺, Cr³⁺ with varying concentrations of Cr co‐doping were prepared by solid‐state synthesis method. Crystalline fibres were obtained by controlled annealing temperature. Synthesized compositions were characterized for their phase and crystallinity by powder x‐ray diffraction. The crystalline morphology was investigated using SEM analysis. High resolution transmission electron microscopy (HRTEM) in image and diffraction modes was used to investigate the microstructure. The effect of Cr doping on quality and morphology of grown crystals was investigated. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Synthesis and thermal characterization of methylammonium tetrachloro zincate (II) monohydrate crystals

Single crystals of methylammonium tetrachloro zincate (II) monohydrate were grown by slow evaporation of saturated aqueous solutions at room temperature. The grown crystals were colourless, bright and transparent. The crystals were characterized through elemental analysis, powder X‐ray diffraction, thermogravimetric (TG‐DTA) and low temperature differential scanning calorimetric (DSC) techniques. While the powder XRD pattern shows the crystallinity of the compound, the elemental analysis and the TG‐DTA confirm the stoichiometry of the compound. The low temperature DSC indicates first order structural phase transition at ‐8°C during heating cycle. The FTIR and far IR spectra of the compound show characteristic vibrational frequencies due to CH₃NH₃ and ZnCl₄^2‐ ions and other chemical bonds. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

煅烧和除碳温度对氮化硼晶须的影响

以三聚氰胺和硼酸为原料通过水浴加热合成晶须前驱体,然后经高温烧结成功制备出BN晶须.扫描电镜显示制备的BN晶须为针状结构,其直径和长径比分别为2～3 μm和40～100.通过X射线衍射分析,制备的BN晶须为六方晶相,晶格参数为a=0.2524 nm和c=0.6592 nm.红外光谱图谱表明在1383 cm-1和 812 cm-1处存在两个明显的B-N特征吸收带.晶须的烧成制度以及除碳温度对晶须形貌和性能的影响研究结果表明,当烧成温度为1700 ℃、除碳温度为600 ℃时可制备出形貌良好和结晶度高的氮化硼晶须.     

Hydrothermal synthesis and formation of 4ZnO·B2O3·H2O whiskers via a new route

4ZnO·B₂O₃·H₂O whiskers were prepared from 2ZnO·3B₂O₃·3.5H₂O under hydrothermal process at 160 °C for 10 h. The synthesized product was characterized by XRD, SEM, TG‐DSC and FT‐IR. SEM results showed that the synthesized 4ZnO·B₂O₃·H₂O whiskers' length was about 3–10 μm and the diameter was 0.2–0.3 μm. Further study on the whiskers' growth process and mechanism showed that the formation of the whiskers went through three stages and the morphology of 4ZnO·B₂O₃·H₂O changed from irregular particles to rod‐like structures and finally to whiskers. The variation of the morphology of the 4ZnO·B₂O₃·H₂O whisker with the concentration of the starting material was investigated. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Growth of YCOB single crystals by flux technique and their characterization

Nonlinear optical single crystals of YCOB with good optical quality were grown by the flux technique for the first time. Polycrystalline YCOB samples were synthesized by solid state reaction method. The thermal analysis of the sample was performed with lithium carbonate flux in different weight proportions and the growth temperature was optimised. Single crystals of YCOB with dimensions 3 × 3 × 5 mm³ were obtained by the method of ‘slow‐cooling’. The grown crystals were characterized by XRD, UV‐VIS‐NIR, EDAX, FTIR and etching studies. The powder XRD pattern revealed the formation of YCOB compound. The lattice parameters were identified through single crystal XRD studies. The UV‐VIS‐NIR results showed that the crystal has a sharp cutoff at 220 nm and is nearly 55% transparent over a wide wavelength range enabling applications in the UV region. The EDAX measurement revealed the ‘flux‐free’ crystal formation. The presence of the functional groups belonging to the YCOB crystals was identified by the FTIR results. ‘Hillock‐like’ patterns are observed in the etching studies. The primary emphasis in this study is laid to describe ‘flux technique’ as an alternative method to grow YCOB crystals. The results are presented and discussed. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Synthesis of bamboo‐like SiC whiskers from waste silica fume

A process for the utilization of wasted silica fume is proposed in this work. Silicon carbide (SiC) whiskers several tens of micrometers in length and with a bamboo‐like morphology have been successfully synthesized by a carbothermal reduction process using purified silica fume as the silicon source. The morphology and structure of SiC whiskers were investigated by X‐ray diffraction, Raman spectroscopy, scanning electron microscopy, and high‐resolution transmission electron microscopy. Studies found that the as‐synthesized whiskers were grown as single‐crystalline β‐SiC along the (111) growth direction. The whiskers consisted of hexagonal stems randomly decorated with larger‐diameter knots along their whole length. On the basis of the characterization results, a vapor–solid process was discussed as a possible growth mechanism of the β‐SiC whiskers.     

方解石制备碳酸钙晶须的影响因素及机理

以方解石矿石为原料,利用制备的重镁水(Mg(HCO₃)₂)及中间产物氯化钙制备文石型碳酸钙晶须,并采用SEM、XRD及EDS对产品进行表征。探究了重镁水与氯化钙反应过程中反应温度、反应时间、镁钙浓度比、重镁水浓度以及搅拌速度对碳酸钙晶须形貌的影响。通过单因素实验得出了最佳工艺条件:温度40 ℃、反应时间2 h、镁钙浓度比6∶1、重镁水浓度0.14 mol/L、搅拌速度150 r/min。在此条件下,制得了长度为40~65 μm、直径为0.6~1.5 μm、长径比为25~45的文石型碳酸钙晶须。     

Crystal growth,optical and luminescence properties of (Ce,Sr)‐doped PrAlO3 single crystals

Using the micro‐pulling‐down method, (Ce,Sr)‐doped PrAlO₃ square‐shaped single crystals (4×4×12 mm) were grown. Structural parameters studied by X‐ray powder diffraction were consistent with R3m space group. Compositional homogeneity was checked with electron probe micro‐analysis and found quite uniform. Absorption spectra and luminescence characteristics under UV and X‐ray excitations were measured at room temperature with no Ce‐related emission appeared. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Synthesis of nano‐crystalline zeolite β: Effects of crystallization parameters

The effects of variation in Si/Al ratio (25 and 100) and crystallization temperature (80 °C to 180 °C, at an interval of 20 K) on crystal size of zeolite β were studied. Products obtained at different synthesis parameters were characterized by powder X‐ray diffraction, IR spectroscopy, thermal analysis, scanning electron microscopy and nitrogen adsorption. Increase in crystal size with crystallization temperature and Si/Al molar ratio was observed. Crystal morphology at 140 °C was spherical whereas at 180 °C it was of irregular shape. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Preparation,physicochemical and third order nonlinear optical properties of bis(tetrabutylammonium)bis(2‐thioxo‐1,3‐dithiole‐4,5‐dithiolato)mercurate(II)

Bis(tetrabutylammonium)bis(2‐thioxo‐1,3‐dithiole‐4,5‐dithiolato)mercurate(II) was prepared and characterized by elemental analyses, electronic absorption, infrared and X‐ray powder diffraction spectroscopy. The specific heat of the crystal was measured to be 1878.2 J.mol^–1K^–1 at 300 K. The thermal decomposition process was investigated by means of thermogravimetric analysis and differential thermal analysis measurements in air together with infrared and X‐ray powder diffraction spectra. The third‐order nonlinear optical properties at 800 nm were measured by femtosecond optical Kerr gate technique by using CS₂ as reference. The third‐order optical susceptibility of its acetone solution at the concentration of 9.27 × 10^–4 M was obtained to be 2.53 × 10^–14 esu. The second‐order hyperpolarizability was estimated to be 1.7 × 10^–32 esu and the response time was about 226 fs. The third order nonlinear optical properties at 532 nm were investigated by using the Z‐scan technique with 20 ps. It exhibited self‐focusing effect and saturable absorption. The second molecular hyperpolarizability was estimated to be 8.4 × 10^–32 esu. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Preparation and Properties of a Novel Nonlinear Optical Crystal: MnHg(SCN)4(H2O)2.2(C3H6CONCH3)

In this article, diaquatetrakis (thiocyanato) manganese(II) mercury(II)‐N‐methyl‐2‐pyrrolidone, MnHg(SCN)₄(H2O)₂.2(C₃H₆CONCH₃), (abbreviated as MMTWMP), a new organometallic nonlinear optical crystal material is reported. The structure, optical and thermal characterizations were determined by elemental analysis, infrared and Raman spectroscopy, X‐ray powder diffraction, thermogravimetric analysis, differential scanning calorimetry, special heat, SHG measurements and UV/Vis/NIR optical transmission spectra. It belongs to the tetragonal crystallographic system, with cell parameters: a = 12.1294, c = 8.2238Å, V = 1211.27ų. Single crystals with dimensions up to 8 × 7 × 5 mm³ have been obtained. The morphology of the crystals was indexed. The MMTWMP crystal exhibits good physicochemical stability at normal temperature and pressure. Its UV transparency cutoff is 360 nm, which is shifted to the violet by 13 nm, as compared with MnHg(SCN)₄ (MMTC); the optical transmission is 44.82% at 404 nm, which is by 17.46% higher than that of MMTC.     

Synthesis,conversion and comparison of the photocatalytic and electrochemical properties of ZnSe·N2H4 and ZnSe microrods

Novel ZnSe·N₂H₄ complex microrods with ∼2 μm in length and 100∼200 nm in diameter were successfully prepared by the solvothermal method at 110°C for 10 h, employing ZnAc₂·2H₂O and Se powders as the reactants, N₂H₄·H₂O as the reductant and medium. Experiments showed that the as‐obtained complex could be further converted into pure hexagonal ZnSe in an ethanol medium at 180 °C for 10 h, and the morphology hardly changed. The as‐prepared products were characterized by X‐ray powder diffraction (XRD), Energy dispersive spectrum (EDS), IR spectrum, Thermogravimetric (TG) analysis and Field emission scanning electron microscopy (SEM). Also, their photocatalytic degradation and electrochemical property were compared. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Low temperature synthesis of thiol‐functionalized CdTe nanoclusters with different tellurium contents

In recent years thiol‐functionalized cadmium telluride nanoparticles act as a core layers for obtaining high photovoltaic efficiency in conjugated polymer/inorganic nanocrystal solar cells and also provide easy tuning of quantum size effect by varying thiol groups and processing temperature. In this work, thiol functionalized CdTe nanoclusters were prepared for different tellurium concentrations at low temperature and its impact has been discussed. Structural parameters estimated by X‐ray diffraction revealed hexagonal phases at lower tellurium concentration and cubic phase at higher tellurium concentrations. Surface morphology of the samples analyzed by transmission electron microscopy, exhibited cluster type of morphology. Optical band gap energy estimated by diffused electron microscopy showed an increase with Te content and band edge emission has been observed in the photoluminescence spectra of CdTe nanoclusters around 620 nm. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Morphology control of CuO micro‐particles using Zn2+ ion and ultrasonic treatment

Novel tomato‐shaped copper oxide crystals has been prepared by a simple hydrothermal method with the presence of Zn²⁺ ion. The ultrasonic pretreatment has proved to be the key factor during the synthesis process. Scanning electron microscope, energy dispersive X‐ray spectrometry and powder X‐ray diffraction were used to characterize the microstructure and morphology of the as‐prepared products. The obtained tomato‐shaped CuO particles were constructed by nanorods with the diameter of about 20 nm. The possible growth mechanism was proposed based on the experimental results. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

EDTA‐assisted synthesis of rose‐like ZnO architectures

Rose‐like ZnO nanostructures were prepared by a low‐temperature solution route with assistance of ethylenediaminetetraacetic acid disodium (EDTA‐2Na). The morphology of ZnO nanostructures was found to change from nanowire arrays to rose‐ and tower‐like architectures with increasing the molar ratio of EDTA‐2Na/Zn²⁺. Also, the shape evolution of ZnO nanostructures with time was observed from flat nanosheets to wrinkled nanosheets and to rose‐like nanostructures. EDTA‐2Na as a strong complexing agent was found to play a key role in the shape evolution. Photoluminescence spectra show that the rose‐like ZnO architectures have more defects than the nanowire arrays. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)