The formation and electrochemical property of lithium-excess cathode material Li<Subscript>1.2</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>Mn<Subscript>0.54</Subscript>O<Subscript>2</Subscript> with petal-like nanoplate microstructure

Lithium-excess oxide shows great potential for its high specific capacity of exceeding 280 mAh g^?1. However, the poor rate capability caused by the poor electrochemical kinetics condition as well as the structure instability block the way of its application. Here, we aimed to improve the kinetics circumstance for lithium ion transference through the material bulk by synthesizing lithium-excess oxide with high specific surface area. Petal-like nanoplates and nanoparticles with excellent electrochemical performance were obtained at different sintering temperatures and times by the electrospinning-sintering method, which facilitates the sufficient contact of electrode and electrolyte and helps to reduce the polarization during the electrochemical reaction process. Cyclic voltammetry tests verify that a portion of oxidized oxygen is reduced reversibly at 3.0 V and the reduction of oxygen contributes to the discharge capacity. Electrochemical impedance spectroscopy plots illustrate the ameliorative electrochemical kinetics is conductive to the oxidation of oxygen at 4.5 V.     

Improving the electrochemical performance of Li-rich Li<Subscript>1.2</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>Mn<Subscript>0.54</Subscript>O<Subscript>2</Subscript> cathode material by LiF coating

To suppress the capacity fade of Li-rich Li_1.2Ni_0.13Co_0.13Mn_0.54O₂ material as cathode materials for lithium-ion battery, we introduce a LiF coating layer on the surface to improve the cycling performance of Li_1.2Ni_0.13Co_0.13Mn_0.54O₂ material. The modified sample shows a capacity of 163.2 mAh g^?1 with a capacity retention of 95% after 100 cycles at a current density of 250 mA g^?1, while the pristine sample only delivers a capacity of 129.9 mAh g^?1 with a capacity retention of 82%. Compared with the pristine material, the LiF-modified sample exhibits an obvious enhancement in the electrochemical performance, which will be very beneficial for this material to be commercialized on the new energy vehicles and other related areas.     

Improved electrochemical properties of YF<Subscript>3</Subscript>-coated Li<Subscript>1.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>O<Subscript>2</Subscript> as cathode for Li-ion batteries

Yttrium fluoride YF₃ layer with different coating contents is successfully covered on the surface of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ via a common wet chemical approach. The XRD, SEM, TEM, and charge-discharge tests are applied to investigate the influence of YF₃ layer on the micro-structural, morphology, and electrochemical properties of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂. And the electrochemical test results demonstrate that the YF₃-coated LMNCO samples exhibit the improved electrochemical properties. The 2wt.%YF₃-coated LMNCO delivers a discharge capacity of 116.6 mAh g^?1 at 5 C rate, much larger than that (95.6 mAh g^?1) of the pristine one. Besides, the electrochemical impedance spectroscopy (EIS) and cyclic voltammetric results indicate that the YF₃ coating layer can promote the optimization formation of SEI film and reversibility of the electrochemical redox.     

Influence of co-precipitation temperature on microstructure and electrochemical properties of Li[Li<Subscript>0.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>]O<Subscript>2</Subscript> cathode materials for lithium ion batteries

The layered Li-rich Mn-based cathode materials Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ were prepared by using co-precipitation technique at different temperatures, and their crystal microstructure and particle morphology were observed and analyzed by XRD and SEM. The electrochemical properties of these samples were investigated by using charge-discharge tests, electrochemical impedance spectroscopy (EIS), and cyclic voltammetry (CV), respectively. The results indicated that all samples are of high purity. When the precursors were co-precipitated at 50 °C, their cathode materials have the most uniform and full particles and exhibit the highest initial discharge capacity (289.4 mAh/g at 0.1C), the best cycle stability (capacity retention rate of 91.2 % after 100 cycles at 0.5C), and the best rate performance. The EIS results show that the lower charge transfer resistance of 50 °C sample is responsible for its superior discharge capacity and rate performance.     

Improvement in rate capability of lithium-rich cathode material Li[Li<Subscript>0.2</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>Mn<Subscript>0.54</Subscript>]O<Subscript>2</Subscript> by Mo substitution

Lithium-rich cathode material Li[Li_0.2Ni_0.13Co_0.13Mn_0.54]O₂ doped with trace Mo is successfully synthesized by a sol-gel method. The X-ray diffraction patterns show that trace Mo substitution increases the inter-layer space of the material, of which is benefiting to lithium ion insertion/extraction among the electrode materials. The (CV) tests demonstrate the decrease of polarization, and on the other hand, the lithium ion diffusion coefficient (D _Li) of the modified material turns out to be larger, which indicates a faster electrochemical process. As a result, the Mo doped material possesses high rate performance and good cycling stability, and the initial discharge capacity reaches 149.3 mAh g^?1 at a current density of 5.0 °C, and the residual capacity is 144.0 mAh g^?1 after 50 cycles with capacity retention of 96.5 % in the potential range of 2.0–4.8 V at room temperature.     

Effects of doping Al on the structure and electrochemical performances of Li[Li<Subscript>0.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>]O<Subscript>2</Subscript> cathode materials

The Li-rich cathode material Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ had been successfully synthesized by a carbonate coprecipitation method. The effects of substituting traces of Al element for different transitional metal elements on the crystal structure and surface morphology had been investigated by X-ray diffraction (XRD) and field emission scanning electron microscopy. The results revealed that all the materials showed similar XRD patterns and surface morphology. It was demonstrated that LNCMAl1 exhibited the superior electrochemical performance. The discharge capacity was 265.2 mAh g^?1 at 0.1 C and still maintained a discharge capacity of 135.6 mAh g^?1 at 5.0 C. The capacity retention could still be 58.2 and 66.8% after 50 cycles at 1.0 and 2.0 C, respectively. Electrochemical impedance spectra results proved that the remarkably improved rate capability and cycling performance could be ascribed to the low charge transfer resistance and enhanced reaction kinetics.     

Surface-modified Li[Li<Subscript>0.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>]O<Subscript>2</Subscript> nanoparticles with LaF<Subscript>3</Subscript> as cathode for Li-ion battery

The LaF₃-coated Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ nanoparticles were synthesized via co-precipitation method followed by simple chemical deposition process. The crystal structure, particle morphology, and electrochemical properties of the bare and coated materials were studied by XRD, SEM, TEM, charge–discharge tests. The results showed that the surface coating on Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ nanoparticles were amorphous LaF₃ layer with a thickness of about 10–30 nm. After the surface modification with LaF₃ films, the coating layer served as a protective layer to suppress the side reaction between the positive electrode and electrolyte, and the Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ oxide demonstrated the improved electrochemical properties. The LaF₃-coated Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ electrode delivered the capacities of 270.5, 247.9, 197.1, 170.0, 142.7, and 109.5 mAh g^?1 at current rates of 0.1, 0.2, 0.5, 1, 2, and 5 C rate, respectively. Besides, the capacity retention was increased from 85.1 to 94.8 % after 100 cycles at 0.5 C rate. It implied surface modification with LaF₃ played an important role to improve the cyclic stability and rate capacity of the Li-rich nickel manganese oxides.     

CeO<Subscript>2</Subscript> coating to improve the performance of Li[Li<Subscript>0.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>]O<Subscript>2</Subscript>

The Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ coated with CeO₂ has been fabricated by an ionic interfusion method. Both the bare and the CeO₂-coated samples have a typical layered structure with R-3m and C2/m space group. The results of XRD and TEM images display that the CeO₂ coating layer on the precursor could enhance the growth of electrochemically active surface planes ((010), (110), and (100) planes) in the following ionic interfusion process. The results of galvanostatic cycling tests demonstrate that the CeO₂-coated sample has a discharge capacity of 261.81 mAh g^?1 with an increased initial Coulombic efficiency from 62.4 to 69.1% at 0.05 °C compared with that of bare sample and delivers an improved capacity retention from 71.7 to 83.4% after 100 cycles at 1 °C (1 °C?=?250 mA g^?1). The results of electrochemical performances confirm that the surface modification sample exhibits less capacity fading, lower voltage decay, and less polarization.     

Improved electrochemical performance of Li<Subscript>1.2</Subscript>Ni<Subscript>0.2</Subscript>Mn<Subscript>0.6</Subscript>O<Subscript>2</Subscript> cathode material with fast ionic conductor Li<Subscript>3</Subscript>VO<Subscript>4</Subscript> coating

Layered lithium-enriched nickel manganese oxides Li_1.2Ni_0.2Mn_0.6O₂ have been synthesized and coated by fast ionic conductor Li₃VO₄ with varying amounts (1, 3, and 5 wt%) in this paper. The effect of Li₃VO₄ on the physical and electrochemical properties of Li_1.2Ni_0.2Mn_0.6O₂ has been discussed through the characterizations of X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscope (TEM), discharge, cyclic performance, rate capability, and electrochemical impedance spectroscopy (EIS). The discharge capacity and coulomb efficiency of Li_1.2Ni_0.2Mn_0.6O₂ in the first cycle have been improved after Li₃VO₄ coating. And, the 3 wt% Li₃VO₄-coated Li_1.2Ni_0.2Mn_0.6O₂ shows the best discharge capacity (246.8 mAh g^?1), capacity retention (97.3 % for 50 cycles), and rate capability (90.4 mAh g^?1 at 10 C). Electrochemical impedance spectroscopy (EIS) results show that the R _ct of Li_1.2Ni_0.2Mn_0.6O₂ electrode decreases after Li₃VO₄ coating, which is due to high lithium ion diffusion coefficient of Li₃VO₄, is responsible for superior rate capability.     

Investigation of the structural and electrochemical performance of Li<Subscript>1.2</Subscript>Ni<Subscript>0.2</Subscript>Mn<Subscript>0.6</Subscript>O<Subscript>2</Subscript> with Cr doping

Cr-doped layered oxides Li[Li_0.2Ni_0.2???x Mn_0.6???x Cr_2x ]O₂ (x?=?0, 0.02, 0.04, 0.06) were synthesized by co-precipitation and high-temperature solid-state reaction. The materials were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (TRTEM), X-ray photoelectron spectroscopy (XPS), and electrochemical impedance spectroscopy (EIS). XRD patterns and HRTEM results indicate that the pristine and Cr-doped Li_1.2Ni_0.2Mn_0.6O₂ show the layered phase. The Li_1.2Ni_0.16Mn_0.56Cr_0.08O₂ shows the best electrochemical properties. The first discharge specific capacity of Li_1.2Ni_0.16Mn_0.56Cr_0.08O₂ is 249.6 mA h g^?1 at 0.1 C, while that of Li_1.2Ni_0.2Mn_0.6O₂ is 230.4 mA h g^?1. The capacity retaining ratio of Li_1.2Ni_0.16Mn_0.56Cr_0.08O₂ is 97.9% compared with 93.9% for Li_1.2Ni_0.2Mn_0.6O₂ after 80 cycles at 0.2 C. The discharge capacity of Li_1.2Ni_0.16Mn_0.56Cr_0.08O₂ is 126.2 mA h g^?1 at 5.0 C, while that of the pristine Li_1.2Ni_0.2Mn_0.6O₂ is about 94.5 mA h g^?1. XPS results show that the content of Mn³⁺ in the Li_1.2Ni_0.2Mn_0.6O₂ can be restrained after Cr doping during the cycling, which results in restraining formation of spinel-like structure and better midpoint voltages. The lithium-ion diffusion coefficient and electronic conductivity of Li_1.2Ni_0.2Mn_0.6O₂ are enhanced after Cr doping, which is responsible for the improved rate performance of Li_1.2Ni_0.16Mn_0.56Cr_0.08O₂.     

Modification research of LiAlO<Subscript>2</Subscript>-coated LiNi<Subscript>0.8</Subscript>Co<Subscript>0.1</Subscript>Mn<Subscript>0.1</Subscript>O<Subscript>2</Subscript> as a cathode material for lithium-ion battery

The LiNi_0.8Co_0.1Mn_0.1O₂ with LiAlO₂ coating was obtained by hydrolysis–hydrothermal method. The morphology of the composite was characterized by SEM, TEM, and EDS. The results showed that the LiAlO₂ layer was almost completely covered on the surface of particle, and the thickness of coating was about 8–12 nm. The LiAlO₂ coating suppressed side reaction between composite and electrolyte; thus, the electrochemical performance of the LiAlO₂-coated LiNi_0.8Co_0.1Mn_0.1O₂ was improved at 40 °C. The LiAlO₂-coated sample delivered a high discharge capacity of 181.2 mAh g^?1 (1 C) with 93.5% capacity retention after 100 cycles at room temperature and 87.4% capacity retention after 100 cycles at 40 °C. LiAlO₂-coated material exhibited an excellent cycling stability and thermal stability compared with the pristine material. These works will contribute to the battery structure optimization and design.     

Preparation and characterization of Li1.2Ni0.13Co0.13Mn0.54O2 cathode materials for lithium-ion battery

Lithium-rich cathode materials Li_1.2Ni_0.13Co_0.13Mn_0.54O₂ with (sample SF) and without (sample SP) formamide was synthesized by a spray-dry method. The crystalline structure and particle morphology of as-prepared materials were characterized by X-ray diffraction and scanning electron microscope. The specific surface area (SSA) of the Li_1.2Ni_0.13Co_0.13Mn_0.54O₂ prepared from different routes was determined by a five-point Brunauer–Emmett–Teller (BET) method using N₂ as absorbate gas. Being compared with the material synthesized without spray-drying process (sample CP), sample SP has much higher SSA. The additive formamide is helpful to form regular and solid precursor particles in spray-drying process, which results in a slightly aggregation of grains and reduction of SSA for sample SF. The electrochemical activities of the materials are closely related to their morphology and SSA. In the voltage range of 2–4.8 V at 25 °C, sample SP present a discharge capacity of 257 mAh g^?1 at 0.1 C rate and 170 mAh g^?1 at 1 C rate. The sample CP delivered only 136 mAh g^?1 when discharged at 1 C rate. The elevated specific capacity and rate capability are attributed to smaller primary particle and higher SSA. Both cycle performance and rate capability of Li_1.2Ni_0.13Co_0.13Mn_0.54O₂ were improved when formamide was used in spray-dry process. Discharge capacity of SF is 140.5 mAh g^?1 at 2 C rate, and that of SP is 132.3 mAh g^?1. Overlarge SSA of SP may provoke serious side reaction, so that its electrochemical performance was deteriorated.     

Hydrothermal synthesis and electrochemical performance of Mn-doped V<Subscript>6</Subscript>O<Subscript>13</Subscript> as cathode material for lithium-ion battery

Mn_xV_6?xO₁₃ (x?=?0.01, 0.02, 0.03, 0.04) were successfully synthesized via a simple hydrothermal method followed by heat-treatment. Both crystal domain size, electronic conductivity and the lithium diffusion coefficient of the Mn_xV_6?xO₁₃ samples were influenced by the doping amount of Mn²⁺. When x?=?0.02, the product was nano-sized particles and exhibited the best electrochemical performance. The enhanced electrochemical performance originated from its higher total conductivity and higher lithium diffusion coefficient.     

Hierarchical Mn<Subscript>1.5</Subscript>Co<Subscript>1.5</Subscript>O<Subscript>4</Subscript> microspheres constructed from one-dimensional nanorods as high-performance anode material for lithium-ion battery

Mn_1.5Co_1.5O₄ hierarchical microspheres have been successfully synthesized via a solvothermal method and an annealing procedure. Mn_1.5Co_1.5O₄ exhibits advanced cycling performance, and it retains a reversible capacity of 633 mA h g^?1 at a current density of 400 mA g^?1 with a coulombic efficiency of 99.0% after 220 cycles. Its remarkable performance is attributed to the hierarchical structure assembled with nanorods, which increases the contact area between each nanorod and electrolyte. More significantly, the open space between neighboring nanorods and the pores on the surface of nanorods can improve Li⁺ ion diffusion rate. Furthermore, the nanorods have rapid one-dimensional Li⁺ diffusion channels, which not only possess a large specific surface area for high activity but accommodate the volume change during lithiation–delithiation processes. Therefore, Mn_1.5Co_1.5O₄ hierarchical microspheres can act as a promising alternative anode material for lithium-ion battery.     

Synthesis of Li(Ni<Subscript>0.6</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.2</Subscript>)O<Subscript>2</Subscript> with sodium DL-lactate as an eco-friendly chelating agent and its electrochemical performances for lithium-ion batteries

(Ni_0.6Co_0.2Mn_0.2)(OH)₂ precursor has been successfully prepared using hydroxide co-precipitation method. The thermodynamic model of hydroxide co-precipitation with sodium DL-lactate as an eco-friendly chelating agent is proposed. The microstructures of (Ni_0.6Co_0.2Mn_0.2)(OH)₂ precursors and Li(Ni_0.6Co_0.2Mn_0.2)O₂ cathode materials are investigated using X-ray diffractometer and scanning electronic microscopy, while the electrochemical performances of Li(Ni_0.6Co_0.2Mn_0.2)O₂ cathode materials are measured using a charge–discharge test. The influences of pH value on the structure and morphological and electrochemical performances of Li(Ni_0.6Co_0.2Mn_0.2)O₂ cathode materials have been discussed in detail. The results show that the sample at pH?=?11.5 exhibits the best lamellar structure and lowest cation mixing, while the sample at pH?=?11.0 delivers the most uniform and full particles and possesses the highest initial charge–discharge performance of 183.4 mAh/g and the best coulombic efficiency of 77.9% at the voltage range of 3.0–4.3 V. Even after 100 cycles, its discharge capacity still remains 165.2 mAh/g with the best retention rate of 90.1%. Furthermore, the sample at pH?=?11.0 delivers the highest discharge capacity at each current density. Even if discharged at 5C (1000 mA/g), the capacity of 115.6 mAh/g has been achieved. The sample at pH?=?11.0 exhibits the highest Li-ion diffusion coefficients (2.072?×?10^?12 cm²/s).     

Effects of Sn doping on electrochemical characterizations of Li[Ni<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>]O<Subscript>2</Subscript> cathode material

Li[Ni_1/3Co_1/3Mn_1/3]O₂ and Sn-doped Li[Ni_1/3Co_1/3Mn_1/3]O₂ cathode materials for lithium battery are synthesized by a solid-state method. The samples are characterized by X-ray diffraction, scanning electron microscope, electrochemical impedance spectroscopy (EIS), and charge–discharge test. The results show that the Sn-doped Li[Ni_1/3Co_1/3Mn_1/3]O₂ has a typical hexagonal α-NaFeO₂ structure and strawberry-like shape with uniform particle size. It has also been found that the Sn-doped Li[Ni_1/3Co_1/3Mn_1/3]O₂ reveals better electrochemical performances than that without Sn doping. The EIS results suggest that Sn presence decreases the total resistance of Li[Ni_1/3Co_1/3Mn_1/3]O₂, which should be related to the improvement on the electrochemical properties.     

Investigation on the electrochemical performances of Li<Subscript>4</Subscript>Mn<Subscript>5</Subscript>O<Subscript>12</Subscript> for battery applications

In this study, well-crystallized Li₄Mn₅O₁₂ powder was synthesized by a self-propagating combustion method using citric acid as a reducing agent. Various conditions were studied in order to find the optimal conditions for the synthesis of pure Li₄Mn₅O₁₂. The precursor obtained was then annealed at different temperatures for 24 h in a furnace. X-ray diffraction results showed that Li₄Mn₅O₁₂ crystallite is stable at relatively low temperature of 400 °C but decompose to spinel LiMn₂O₄ and monoclinic Li₂MnO₃ at temperatures higher than 500 °C. The prepared samples were also characterized by FESEM and charge-discharge tests. The result showed that the specific capacity of 70.7 mAh/g was obtained within potential range of 4.2 to 2.5 V at constant current of 1.0 mA. The electrochemical performances of Li₄Mn₅O₁₂ material was further discussed in this paper.     

Investigation on LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> cathode material based on the precursor of nickel-manganese compound for lithium-ion battery

The high-voltage spinel LiNi_0.5Mn_1.5O₄ (LNMO) with submicron particle size (LNMO-850₅P700₁₀) has been synthesized based on nickel-manganese compound, which is obtained from pre-sintering the nickel-manganese hydroxide precipitation at 850 °C. The LNMO materials based on nickel-manganese hydroxide (LNMO-700₁₀, LNMO-850₅700₁₀, and LNMO-850₁₀700₁₀) have also been synthesized for comparison to study the pre-sintering impact on the properties of LiNi_0.5Mn_1.5O₄ material. The morphologies and structures of the obtained samples have been analyzed by X-ray powder diffraction and scanning electron microscopy. The nickel-manganese compound has a spinel structure with high crystallinity, making it a good precursor to form high-performance LNMO with lower content of Mn³⁺ and impurity. The obtained LNMO-850₅P700₁₀ delivers discharge capacities of 125.4 mA h g^?1 at 0.2 C, and the capacity retention of 15 C reaches 73.8 % of the capacity retention of 0.2? C. Furthermore, it shows a superior cyclability with the capacity retention of 96.4 % after 150 cycles at 5 ?C. Compared with the synthesis method without pre-sintering, the synthesis method with pre-sintering can save energy while reaching the same discharge specific capacity.     

Improvement of electrochemical performance for AlF<Subscript>3</Subscript>-coated Li<Subscript>1.3</Subscript>Mn<Subscript>4/6</Subscript>Ni<Subscript>1/6</Subscript>Co<Subscript>1/6</Subscript>O<Subscript>2.40</Subscript> cathode materials for Li-ion batteries

Li-rich layered-layered-Spinel structure spherical Li_1.3Mn_4/6Ni_1/6Co_1/6O_2.40 particles was successfully prepared and coated with a uniform layer by a two-step co-precipitation method and evaluated in lithium cells. The structures and electrochemical properties of pristine Li_1.3Mn_4/6Ni_1/6Co_1/6O_2.40 and AlF₃-coated Li_1.3Mn_4/6Ni_1/6Co_1/6O_2.40 were characterized. When the coating amount was 2 wt%, the cathode showed the best cycling performance and rate capability compared to others. The AlF₃-coated Li_1.3Mn_4/6Ni_1/6Co_1/6O_2.40 Li-ion cell cathode had a capacity retention of 90.07 % after 50 cycles at 0.5 C over 2.0–4.8 V, while the pristine Li_1.3Mn_4/6Ni_1/6Co_1/6O_2.40 exhibited capacity retention of only 80.73 %. Moreover, the rate capability and cyclic performance also improved. Electrochemical impedance spectroscopy testing revealed that the improved electrochemical performance might attribute to the AlF₃ coating layer which can suppress the increase of impedance during the charging and discharging process by preventing direct contact between the highly delithiated active material and electrolyte.     

Synthesis and electrochemical properties of P2-Na<Subscript>2/3</Subscript>Ni<Subscript>1/3</Subscript>Mn<Subscript>2/3</Subscript>O<Subscript>2</Subscript>

The pure phase P2-Na_2/3Ni_1/3Mn_2/3O₂ was synthesized by a solid reaction process. The optimum calcination temperature was 850 °C. The as-prepared product delivered a capacity of 158 mAh g^?1 in the voltage range of 2–4.5 V, and there was a phase transition from P2 to O2 at about 4.2 V in the charge process. The P2 phase exhibited excellent intercalation behavior of Na ions. The reversible capacity is about 88.5 mAh g^?1 at 0.1 C in the voltage range of 2–4 V at room temperature. At an elevated temperature of 55 °C, it could remain as an excellent capacity retention at low current rates. The P2-Na_2/3Ni_1/3Mn_2/3O₂ is a potential cathode material for sodium-ion batteries.