Preparation of TEMPO-contained pyrrole copolymer by in situ electrochemical polymerization and its electrochemical performances as cathode of lithium ion batteries

Composite electrodes based on the nitroxide free radical-contained pyrrole copolymer (PPy-co-PPy-C-TEMPO) as active material were one-step synthesized by in situ electrochemical polymerization, which was then directly applied as the cathode of lithium ion batteries. The structure, morphology, electrochemical property, and charge-discharge performances of prepared copolymers were characterized by FTIR, SEM, cyclic voltammogram, electrochemical impedance spectroscopy, and galvanostatic charge-discharge testing, respectively. The results demonstrated that PPy-co-PPy-C-TEMPO-based composite cathodes have been successfully prepared by in situ electrochemical method, and the introduction of the nitroxide free radical (TEMPO) could obviously affect the morphology and electrochemical characteristics of the obtained electroactive polymers. And the charge/discharge tests showed that with the introduction of the TEMPO, PPy-co-PPy-C-TEMPO-based composite cathodes exhibited an improved specific capacity of 70.9 mAh g^?1 for PPy-co-PPy-C-TEMPO (4:1) and 62.6 mAh g^?1 for PPy-co-PPy-C-TEMPO (8:1) as measured at 20 mA g^?1 between 2.5 and 4.2 V, which were remarkably higher than that of the pure PPy cathode of 41.0 mAh g^?1 under the same experimental conditions. Also, the obtained PPy-co-PPy-C-TEMPO copolymers demonstrated an acceptable cycling stability during the charge-discharge process. These obtained cell performances for the composite cathodes were attributed to the application of the in situ electrochemical polymerization technology, which enhanced the intimate integration between conductive polymer film and electrode. Furthermore, the introduction of TEMPO-contained pyrrole (Py-C-TEMPO) improved the morphology of the composite cathode, which was in favor of the utilization of active materials and the improved electrochemical performances.     

Pickering emulsion polymerization of polyaniline/LiCoO2 nanoparticles used as cathode materials for lithium batteries

The oil in water (o/w) emulsions were prepared using aniline dissolved in toluene and LiCoO₂ particles as stabilizers (Pickering emulsions). Pickering emulsions are stabilized by adsorbed solid particles instead of emulsifier molecules. The mean droplet diameter of emulsions was controlled by the mass ratio M (oil)/M (solid particles). The emulsions showed great stability during 3 days. The composite materials containing LiCoO₂ and the conductive polymer polyaniline (PANI) have been prepared by means of polymerization of aniline emulsion stabilized by LiCoO₂ particles. The composite materials were characterized by nanosphere and nanofiber-like structures. The nanofiber-like morphology of the powdered material was distinctly different of the morphologies of the parent materials. The electrochemical reactivity of PANI/LiCoO₂ composites as positive electrode in a lithium battery was examined during lithium ion deinsertion and insertion by galvanostatic charge–discharge testing; PANI/LiCoO₂ (1:4) composite materials exhibited the best electrochemical performance by increasing the reaction reversibility and capacity compared to that of the pristine LiCoO₂ cathode. The first discharge capacity of PANI/LiCoO₂ (1:4) was 167 mAh/g, while that of LiCoO₂ was136 mAh/g.     

Vertical aligned V<Subscript>2</Subscript>O<Subscript>5</Subscript> nanoneedle arrays grown on Ti substrate as binder-free cathode for lithium-ion batteries

V₂O₅ nanoneedle arrays were grown directly on titanium (Ti) substrate by a facile solvothermal route followed with calcination at 350 °C for 2 h. The as-prepared V₂O₅ nanoneedles are about 50 nm in diameter and 800 nm in length. The electrochemical behavior of V₂O₅ nanoarrays as binder-free cathode for lithium-ion batteries (LIBs) was evaluated by cyclic voltammetry and galvanostatic discharge/charge tests. Compared with V₂O₅ powder electrode, V₂O₅ nanoneedle arrays electrode exhibited improved electrochemical performance in terms of high discharge capacity of 262.5 mA h g^?1 between 2.0 and 4.0 V at 0.2 C, and high capacity retention up to 77.1% after 100 cycles. Under a high current rate of 2 C, a discharge capacity of about 175.6 mA h g^?1 can be maintained. The enhanced performance are mainly due to the intimate contact between V₂O₅ nanoneedle active material and current collector, which enable shortened electron transfer pathway and improved charge transfer kinetics, demonstrating their potential applications in high rate electrochemical storage devices.     

Synthesis and electrochemical performance of carbon-coated LiCoBO<Subscript>3</Subscript> as cathode materials for lithium-ion batteries

Carbon-coated LiCoBO₃ (LiCoBO₃/C) is prepared by sol-gel method and polyethylene glycol 6000 (PEG-6000) is chosen as carbon source. The LiCoBO₃/C sample exhibits an initial discharge capacity of 76.7 mAh g^?1 at 0.1 C, and it can deliver a discharge capacity of 65.9 mAh g^?1 after 50 cycles, while the LiCoBO₃ sample only presents a first discharge capacity of 34.3 and 16.8 mAh g^?1 at the 50th cycle, LiCoBO₃/C sample shows better cycling performance than that of LiCoBO₃. The improved electrochemical properties could be mainly ascribed to the conductive carbon network and the reduced particle size of the LiCoBO₃ powders. Electrochemical impedance spectroscopy (EIS) results confirm that carbon coating decreases the charge transfer resistance and improve the electrochemical reaction kinetics.     

Sulfur/microporous carbon composites for Li-S battery

A commercial carbon black with microporous framework is used as carbon matrix to prepare sulfur/microporous carbon (S/MC) composites for the cathode of lithium sulfur (Li-S) battery. The S/MC composites with 50, 60, and 72 wt.% sulfur loading are prepared by a facile heat treatment method. Electrochemical performance of the as-prepared S/MC composites are measured by galvanostatic charge/discharge tests, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS), with carbonate-based electrolyte of 1.0 M LiPF₆/(PC-EC-DEC). The composite with 50 wt.% sulfur presents the optimized electrochemical performance, including the utilization of active sulfur, discharge capacity, and cycling stability. At the current density of 50 mA g^?1, it can demonstrate a high initial discharge capacity of 1624.5 mAh g^?1. Even at the current density of 800 mA g^?1, the initial capacity of 1288.6 mAh g^?1 can be obtained, and the capacity can still maintain at 522.8 mAh g^?1 after 180 cycles. The remarkably improved electrochemical performance of the S/MC composite with 50 wt.% sulfur are attributed to the carbon matrix with microporous structure, which can effectively enhance the electrical conductivity of the sulfur cathode, suppress the loss of active material during charge/discharge processes, and restrain the migration of polysulfide ions to the lithium anode.     

Simple microwave synthesis and improved electrochemical performance of Nb-doped MnO<Subscript>2</Subscript>/reduced graphene oxide composite as anode material for lithium-ion batteries

Niobium-doped MnO₂/reduced graphene oxide (Nb-MnO₂/RGO) composite has been successfully synthesized via a simple microwave radiation method. The samples were systematically studied by X-ray diffraction (XRD), thermogravimetric analysis (TG), X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM), transmission electron microscope (TEM), and electrochemical measurements. As the anode material for lithium-ion batteries, the Nb-MnO₂/RGO (molar ratio of Mn/Nb?=?50:1) (NMG50) showed an outstanding reversible discharge capacity of 556.6 mAh g^?1 after 50 cycles with a capacity retention of 77% at a charge-discharge rate of 0.1 A g^?1 and the reversible discharge capacity can still retain 223.3 mAh g^?1 at a current of 1 A g^?1, which is much higher than those for Nb-MnO₂/RGO (molar ratio of Mn/Nb?=?10:1) (NMG10) and undoped MnO₂/RGO (MG). The improved electrochemical performance could be attributed to the proper amount of Nb doping, which could enhance both the conductivity and the structure stability of MnO₂.     

Enhanced electrochemical performance of lithium vanadium phosphate as cathode by LiBOB/LiTFSI with additive in EC/EMC

A series of Li₃V₂(PO₄)₃/C (LVP/C) samples with monoclinic structure indexed to P2₁/n space group were synthesized using V₂O₃ as vanadium source by solid state reaction method by different sintering temperatures. It was found that the LVP/C sintered at 750 °C with a carbon content 3 wt.% was the optimum condition for this synthesis. The structural, morphological, superficial, and textural properties of LVP/C were characterized by XRD, SEM, TEM, and XPS. The electrochemical performance was evaluated by galvanostatic charge–discharge cycling using new high voltage electrolyte. The optimized cell delivered an initial discharge capacity of 187 mAh g^?1 in the higher cut-off voltage of 3.0–4.8 V vs. Li⁺/Li⁰ at 0.2 C rate, with a capacity retention of 88 %, 89 %, and 61 % after 50 cycles discharging at 1 C, 2 C, and 4 C, respectively. The capacity can be almost recovered at 0.5 C after long cycles. The excellent stability is contributed to the new high-voltage electrolyte.     

Pulsed electrodeposition of mesoporous cobalt-doped manganese dioxide as supercapacitor electrode material

Cobalt-doped MnO₂, as electrode material for supercapacitor, was synthesized by pulse electrodeposition method. The morphology and structure of the products were characterized by X-ray diffraction (XRD) and field-emission scanning electron microscope (FE-SEM). The results show that the crystal structure of the products is γ-type, and the samples reveals a porous texture composed of manganese oxide nanosheets. Cyclic voltammetry (CV), electrochemical impedance spectrometry (EIS), and galvanostatic charge–discharge tests indicate that doping cobalt has great effect on the electrochemical performance of manganese dioxide material. A specific capacitance of 354 F g^?1 is obtained when the molar ratio of Mn to Co is 200:10. After 100 charge–discharge cycles in 6 M KOH solution, the specific capacitance stabilized at 333.6 F g^?1, exhibiting excellent capacitance retention ability.     

Synthesis of LiCoPO4 as cathode material for lithium-ion batteries by the rheological phase method

LiCoPO₄ has been successfully synthesized by a simple rheological phase method. The effects of synthesis temperature on the properties of LiCoPO₄ are also investigated. The results show that a well-crystallized olivine structure LiCoPO₄ with no obvious impurity phase is obtained. The electrochemical properties of LiCoPO₄ were examined by galvanostatic charge/discharge tests, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS). The results indicate that the sintering temperature has a significant effect on the electrochemical properties of LiCoPO₄. The sample fired at 600 °C shows the best electrochemical properties. The initial discharge capacity is 101.0, 96.8, and 91.6 mAh g^?1 at 0.1, 0.2, and 1 C, respectively. The significantly improved electrochemical properties of LiCoPO₄ are attributed to the better crystallized rheological phase production with better dispersed and smaller particles, which can greatly facilitate the diffusion of Li⁺.     

Preparation of Si-PPy-Ag composites and their electrochemical performance as anode for lithium-ion batteries

The nanosilicon connected by polypyrrole (PPy) and silver (Ag) particles was simply synthesized by a chemical polymerization process in order to prepare Si-based anodes for Li-ion batteries. The phase structure, surface morphology, and electrochemical properties of the as-synthesized powders were analyzed by X-ray diffraction, FT-IR, scanning electron microscopy, and galvanostatic charge/discharge measurements. The cycle stability of the Si-PPy-Ag composites was greatly enhanced compared with the pure nanosilicon. A high capacity of more than 823 mA h g^?1 was maintained after 100 cycles. The improved electrochemical characteristics are attributed to the volume buffering effect as well as effective electronic conductivity of the polypyrrole and silver in the composite electrode.     

Synthesis and electrochemical investigation of highly dispersed ZnO nanoparticles as anode material for lithium-ion batteries

Highly dispersed ZnO nanoparticles were prepared by a versatile and scalable sol-gel synthetic technique. High-resolution transmission electronic microscopy (HRTEM) showed that the as-prepared ZnO nanoparticles are spherical in shape and exhibit a uniform particle size distribution with the average size of about 7 nm. Electrochemical properties of the resulting ZnO were evaluated by galvanostatic discharge/charge cycling as anode for lithium-ion battery. A reversible capacity of 1652 mAh g^?1 was delivered at the initial cycle and a capacity of 318 mAh g^?1 was remained after 100 cycles. Furthermore, the system could deliver a reversible capacity of 229 mAh g^?1 even at a high current density of 1.5 C. This outstanding electrochemical performance could be attributed to the nano-sized features of highly dispersed ZnO particles allowing for the better accommodation of large strains caused by particle expansion/shrinkage along with providing shorter diffusion paths for Li⁺ ions upon insertion/deinsertion.     

Electrochemical synthesis and performance of PANI electrode material for electrochemical capacitor

Polyaniline (PANI) electrode materials doped with sulfuric acid (H₂SO₄) were prepared by cyclic voltammetry (CV) method in different reaction conditions. The structure and morphology of PANI samples were characterized by Fourier transform infrared spectroscopy and scanning electron microscope. The electrochemical properties of PANI samples were studied by CV, galvanostatic charge/discharge, and electrochemical impedance spectroscopy tests. Additionally, the effects of reaction conditions including aniline concentration, voltammetry scan rate, and deposition time on the morphology and properties of PANI samples were investigated in detail. The results showed that the PANI synthesized under the optimal conditions of 0.2 mol?L^?1 aniline, scan rate 20 mV?s^?1, and deposition time 50 min is in the form of nanorods with a cross-linked network structure. It exhibits an outstanding capacitive performance with good cycle stability and high rate performance. Besides, the specific capacitance of PANI is as high as 757 F?g^?1.     

Hollow structured Sn-Co nanospheres by galvanic replacement reaction as high-performance anode for lithium ion batteries

Hollow Sn-Co nanospheres have been fabricated by galvanic replacement reaction. In particular, the hollow resultants with different shell thickness and void space can be obtained using sacrificial templates with different sizes. The structural evolution of Sn-Co hollow microspheres and structure changes during charge/discharge process were studied using XRD, SEM, and TEM. As an anodic material, the hollow resultants with thin shell and relatively large void space exhibited a good reversible capacity of 502 mAh g^?1 at a current density of 100 mA g^?1 and a coulomb efficiency over 99 % after 100 cycles. The contributions of the hollow structure and the inactive Co element to electrochemical performance were verified by galvanostatic charge/discharge cycling, electrochemical impedance spectroscope, and TEM measurements. A possible mechanism for hollow structure with different shell thickness to alleviate the volume change was proposed.     

Influence of coated MnO2 content on the electrochemical performance of Li1.2Ni0.2Mn0.6O2 cathodes

Layered cathode material Li_1.2Ni_0.2Mn_0.6O₂ has been synthesized using a coprecipitation method and coated by MnO₂ with varying amounts (1, 3, 5, and 9 wt%). The physical properties and electrochemical performances of the materials are characterized by XRD, SEM, charge/discharge tests, cycle life, and rate capability tests. XRD patterns show that the pristine and coated Li_1.2Ni_0.2Mn_0.6O₂ powders exhibit layered structure. The discharge capacities and coulombic efficiencies of Li_1.2Ni_0.2Mn_0.6O₂ in the first cycle have been improved and increase with the increasing content of coated MnO₂. The 9 wt% MnO₂-coated Li_1.2Ni_0.2Mn_0.6O₂ delivers 287 mAhg^?1 for the first discharge capacity and 86.7 % for the first coulombic efficiency compared with 228 mAhg^?1 and 65.9 % for pristine Li_1.2Ni_0.2Mn_0.6O₂. However, the 5 wt% MnO₂-coated Li_1.2Ni_0.2Mn_0.6O₂ shows the best capacity retention (99.9 % for 50 cycles) and rate capability (88.6 mAhg^?1 at 10 C), while the pristine Li_1.2Ni_0.2Mn_0.6O₂ only shows 91.5 % for 50 cycles and 25.3 mAhg^?1 at 10 C. The charge/discharge curves and differential capacity vs. voltage (dQ/dV) curves show that the coated MnO₂ reacts with Li⁺ during the charge and discharge process, which is responsible for higher discharge capacity after coating. Electrochemical impedance spectroscopy results show that the R _ct of Li_1.2Ni_0.2Mn_0.6O₂ electrode decreases after coating, which is responsible for superior rate capability.     

Effects of doping Al on the structure and electrochemical performances of Li[Li<Subscript>0.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>]O<Subscript>2</Subscript> cathode materials

The Li-rich cathode material Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ had been successfully synthesized by a carbonate coprecipitation method. The effects of substituting traces of Al element for different transitional metal elements on the crystal structure and surface morphology had been investigated by X-ray diffraction (XRD) and field emission scanning electron microscopy. The results revealed that all the materials showed similar XRD patterns and surface morphology. It was demonstrated that LNCMAl1 exhibited the superior electrochemical performance. The discharge capacity was 265.2 mAh g^?1 at 0.1 C and still maintained a discharge capacity of 135.6 mAh g^?1 at 5.0 C. The capacity retention could still be 58.2 and 66.8% after 50 cycles at 1.0 and 2.0 C, respectively. Electrochemical impedance spectra results proved that the remarkably improved rate capability and cycling performance could be ascribed to the low charge transfer resistance and enhanced reaction kinetics.     

Influence of post-calcination treatment on the spinel lithium titanium oxide anode material for lithium ion batteries

The influence of post-calcination treatment on spinel Li₄Ti₅O₁₂ anode material is extensively studied combining with a ball-milling-assisted rheological phase reaction method. The post-calcinated Li₄Ti₅O₁₂ shows a well distribution with expanded gaps between particles, which are beneficial for lithium ion mobility. Electrochemical results exhibit that the post-calcinated Li₄Ti₅O₁₂ delivers an improved specific capacity and rate capability. A high discharge capacity of 172.9 mAh g^?1 and a reversible charge capacity of 171.1 mAh g^?1 can be achieved at 1 C rate, which are very close to its theoretical capacity (175 mAh g^?1). Even at the rate of 20 C, the post-calcinated Li₄Ti₅O₁₂ still delivers a quite high charge capacity of 124.5 mAh g^?1 after 50 cycles, which is much improved over that (43.9 mAh g^?1) of the pure Li₄Ti₅O₁₂ without post-calcination treatment. This excellent electrochemical performance should be ascribed to the post-calcination process, which can greatly improve the lithium ion diffusion coefficient and further enhance the electrochemical kinetics significantly.     

Facile preparation of SGC composite as anode for lithium-ion batteries

The silicon/graphite/carbon (SGC) composite was successfully prepared by ball-milling combined with pyrolysis technology using nanosilicon, graphite, and phenolic resin as raw materials. The structure and morphology of the as-prepared materials are characterized by X–ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscope (TEM). Meanwhile, the electrochemical performance is tested by constant current charge–discharge technique, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS) measurements. The electrodes exhibit not only high initial specific capacity at a current density of 100 mA g^?1, but also good capacity retention in the following 50 cycles. The EIS results indicate that the electrodes show low charge transfer impedance R_sf?+?R_ct. The results promote the as-prepared SGC material as a promising anode for commercial use.     

Effect of Ce-doped MnO<Subscript>2</Subscript> catalyst on the lithium-air batteryperformance in the ambient atmosphere

MnO₂ doped with Ce was hydrothermally synthesized and the as-made breathable waterproof membrane used outside the cathode was prepared for improving the lithium-air battery performance in air. The samples were characterized by scanning electron microscopy (SEM), energy dispersive spectrum analysis (EDS), charge–discharge cycle tests, charge–discharge cycle tests of limited capacity, and electrochemical impedance spectroscopy (EIS) tests. The result showed that Ce _x Mn_1-x O₂ can effectively reduce the charge overpotential of the cathode. The charge and discharge electrical potential difference of Ce_0.1Mn_0.9O₂ was only 700 mV while MnO₂’s was 2100 mV. And Ce_0.1Mn_0.9O₂ that exhibited high discharge capacity of 400 mAh g^?1 in air had a stable discharge platform of 2.5 V and then the more obvious charge phenomenon appeared after 3.5 V. The excellent catalysis, the effect of cathode catalytic materials named Ce _x Mn_1-x O₂, may attribute to the decrease of reaction potential energy of oxygen reduction reaction and oxygen evolution reaction.     

Chitosan-ZnO/polyaniline ternary nanocomposite for high-performance supercapacitor

We report on the synthesis of chitosan-zinc oxide (ZnO)/polyaniline (CS-ZnO/PANI) ternary nanocomposites via in situ polymerization of aniline in the presence of CS-ZnO nanocomposite prepared by simple precipitation method. The structure, morphology, and physicochemical properties of prepared ternary composites are characterized by Fourier transform infrared, UV–visible, X-ray diffraction, SEM, EDXS, TEM, thermogravimetric/differential thermal analysis, and N₂ adsorption/desorption measurements. Their electrochemical properties are also investigated using cyclic voltammetry, galvanostatic charge–discharge tests, and electrochemical impedance spectroscopy. Electrochemical measurements show that the mesoporous CS_0.12-ZnO_2.5/PANI electrode yields larger specific capacitance (587.15 F g^?1) than the corresponding PANI-ZnO electrode without added chitosan and the capacitance retention is 80 % after 1,000 charge/discharge cycles at 175 mA cm^?2 current density in the voltage range of 0 to 0.8 V vs. SCE, due to the synergistic effect among three components which result in enhanced specific capacitance and cycling stability. The resulting composites are promising electrode materials for high-performance, environmentally friendly, and low-cost electrical energy storage devices.     

Preparation,properties, and Li-ion battery application of EC + PC-modified PVdF-HFP gel polymer electrolyte films

Based on poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP) and lithium tetrafluoroborate (LiBF₄) salt along with blending plasticizers, ethylene carbonate (EC) and propylene carbonate (PC), high Li-ion-conducting gel polymer electrolyte films are developed. Their properties are characterized by various techniques. The ambient temperature ionic conductivity of the 85PVdF-HFP:15LiBF₄ + 150(EC + PC) electrolyte film has a high value of 8.1 × 10^?4 S cm^?1. Its crystallinity, melting point, and electrochemical stability window are 9.5%, 115 °C, and 4.6 V, respectively. The mechanical testing shows that the Young’s modulus, yield strength, and breaking strain of this electrolyte film are 36.8 MPa, 3.4 MPa, and 320%, respectively. Lithium-ion batteries based on the gel polymer electrolyte film exhibit remarkable charge–discharge and cycling performances. The initial discharge capacity of this battery is as high as 165.1 mAh g^?1 at 0.1 C and just shows a small capacity fading of 4.8% after 120 cycles, indicating that the 85PVdF-HFP:15LiBF₄ + 150(EC + PC) system is an excellent electrolyte candidate for lithium-ion battery applications. The charge–discharge performance of the Li-ion cell fabricated with this gel polymer electrolyte film is apparently better than that of the previously reported Li-ion cells fabricated with other PVdF-HFP-based gel polymer electrolyte films.