Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> quantum dots on 3D-framed graphene aerogel as an advanced anode material in lithium-ion batteries

Three-dimensional fabricated Fe₃O₄ quantum dots/graphene aerogel materials (Fe₃O₄ QDs/GA) were obtained from a facile hydrothermal strategy, followed by a subsequently heat treatment process. The Fe₃O₄ QDs (2–5 nm) are anchored tightly and dispersed uniformly on the surface of three-dimensional GA. The as-prepared anode materials exhibit a high reversible capacity of 1078 mAh g^?1 at a current density of 100 mA g^?1 after 70 cycles in lithium-ion batteries (LIBs) system. Moreover, the rate capacity still remains 536 mAh g^?1 at 1000 mA g^?1. The enhanced electrochemical performance is attributed to that the GA not only acts as a three-dimensional electronic conductive matrix for the fast transportation of Li⁺ and electrons, but also provides with double protection against the aggregation and pulverization of Fe₃O₄ QDs during cycling. Apparently, the synergistic effects of the three-dimensional GA and the quantum dots are fully utilized. Therefore, the Fe₃O₄ QDs/GA composites are promising materials as advanced anode materials for LIBs.     

Flower-like MoS<Subscript>2</Subscript> supported on three-dimensional graphene aerogels as high-performance anode materials for sodium-ion batteries

Flower-like MoS₂ supported on three-dimensional graphene aerogel (MoS₂/GA) composite has been prepared by a facile hydrothermal method followed by subsequent heat-treatment process. Each of MoS₂ microflowers is surrounded by the three-dimensional graphene nanosheets. The MoS₂/GA composite is applied as an anode material of sodium-ion batteries (SIBs) and it exhibits high initial discharge/charge capacities of 562.7 and 460 mAh g^?1 at a current density of 0.1 A g^?1 and good cycling performance (348.6 mAh g^?1 after 30 cycles at 0.1 A g^?1). The good Na⁺ storage properties of the MoS₂/GA composite could be attributed to the unique structure which flower-like MoS₂ are homogeneously and tightly decorated on the surface of three-dimensional graphene aerogel. Our results demonstrate that as-prepared MoS₂/GA composite has a great potential prospect as anodes for SIBs.     

Advanced LiTi<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>/C anode by incorporation of carbon nanotubes for aqueous lithium-ion batteries

Inferior rate capability is a big challenge for LiTi₂(PO₄)₃ anode for aqueous lithium-ion batteries. Herein, to address such issue, we synthesized a high-performance LiTi₂(PO₄)₃/carbon/carbon nanotube (LTP/C/CNT) composite by virtue of high-quality carbon coating and incorporation of good conductive network. The as-prepared LTP/C/CNT composite exhibits excellent rate performance with discharge capacity of 80.1 and 59.1 mAh g^?1 at 10 C and 20 C (based on the mass of anode, 1 C = 150 mA g^?1), much larger than that of the LTP/C composite (53.4 mAh g^?1 at 10 C, and 31.7 mAh g^?1 at 20 C). LTP/C/CNT also demonstrates outstanding cycling stability with capacity retention of 83.3 % after 1000 cycles at 5 C, superior to LTP/C without incorporation of CNTs (60.1 %). As verified, the excellent electrochemical performance of the LTP/C/CNT composite is attributed to the enhanced electrical conductivity, rapid charge transfer, and Li-ion diffusion because of the incorporation of CNTs.     

Synthesis of Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>-reduced graphene oxide composite and its application for hybrid supercapacitors

We describe in this paper the synthesis and the characterization of Li₄Ti₅O₁₂-reduced graphene oxide (LTO-RGO) composite and demonstrate their use as hybrid supercapacitor, which is consist of an LTO negative electrode and activate carbon (AC) positive electrode. The LTO-RGO composites were synthesized using a simple, one-step process, in which lithium sources and titanium sources were dissolved in a graphene oxide (GO) suspension and then thermal treated in N₂. The lithium-ion battery with LTO-RGO composite anode electrode revealed higher discharge capacity (167 mAh g^?1 at 0.2 C) and better capacity retention (67%) than the one with pure LTO. Meanwhile, compared with the AC//LTO supercapacitor, the AC//LTO-RGO hybrid supercapacitor exhibits higher energy density and power density. Results show that the LTO-RGO composite is a very promising anode material for hybrid supercapacitor.     

Graphene-decorated sphere Li<Subscript>2</Subscript>S composite prepared by spray drying method as cathode for lithium-sulfur full cell

In this work, a graphene-decorated Li₂S cathode has been prepared via spray drying method using Li₂SO₄, graphene oxide and sucrose as raw materials. During spray drying, sucrose melts and embeds Li₂SO₄ when Li₂SO₄ were sprayed out with graphene oxide and sucrose, and becomes sphere particles. The as-prepared Li₂S composite was received after a heat treatment under nitrogen atmosphere. X-ray diffraction patterns confirm the cubic structure of Li₂S and scanning electron microscope images reveal that Li₂S and carbon components stay in sphere structure with diameter around 20 μm. The sphere Li₂S composite shows enhanced performance when acts as cathode. Under current density of 100 mA g^?1, a specific discharge capacity of 778 mAh g^?1 has been achieved and the battery cycled over 60 rounds. Furtherly, the sphere composite was coupled with silicon/graphite anode to construct full cell system, suggesting large possibility to work with the current lithium-ion battery anodes.     

Scalable synthesis and superior performance of TiO<Subscript>2</Subscript>-reduced graphene oxide composite anode for sodium-ion batteries

TiO₂-reduced graphene oxide (RGO) composite was synthesized via a sol-gel process and investigated as an anode material for sodium-ion batteries (SIBs). A remarkable improvement in sodium ion storage with a reversible capacity of 227 mAh g^?1 after 50 cycles at 50 mA g^?1 is achieved, compared to that (33 mAh g^?1) for TiO₂. The enhanced electrochemical performance of TiO₂-RGO composite is attributed to the larger specific surface area and better electrical conductivity of TiO₂-RGO composite. The excellent performance of TiO₂-RGO composite enables it a potential electrode material for SIBs.     

Self-assembled 3D Co3O4-graphene frameworks with high lithium storage performance

Three-dimensional Co₃O₄-graphene frameworks (3D-CGFs) are prepared with a one-pot hydrothermal method. Co₃O₄ particles are in situ anchored on graphene sheets, and the resulting composite self-assembles into 3D architecture during the hydrothermal treatment. Scanning electron microscope, transmission electron microscope, powder X-ray powder diffraction, and Raman spectroscopy are employed to characterize the sample. When tested as anode materials for lithium-ion batteries, 3D-CGFs demonstrate remarkable electrochemical lithium storage properties, such as large and stable reversible capacity (>530 mAh g^?1 at 500 mA g^?1 over 300 cycles), good capacity retention (88 % retention after 300 cycles at 500 mA g^?1 compared with the 4th cycle), excellent high-rate performance (515 mAh g^?1 at 1 A g^?1), making it a promising candidate for high-performance anode materials, especially for high-rate lithium-ion batteries.     

V<Subscript>2</Subscript>O<Subscript>5</Subscript>-SiO<Subscript>2</Subscript> hybrid as anode material for aqueous rechargeable lithium batteries

V₂O₅-SiO₂ hybrid material was fabricated by heat-treating a mixture of H₂SiO₃ and V₂O₅. SEM, TEM, XRD, and N₂ isotherm analyses were performed to characterize the morphology and structure details of the as-prepared V₂O₅-SiO₂. The possibility of using the as-prepared V₂O₅-SiO₂ as anode material for aqueous lithium-ion batteries was investigated. Potentiostatic and galvanostatic results indicated that the intercalation/de-intercalation of Li⁺ in this material in aqueous electrolyte was quasi-reversible. It was also found that a discharge capacity of up to 199.1 mAh g^?1 was obtained at a current density of 50 mA g^?1 in aqueous solution of 1 M Li₂SO₄, a value which is much higher than the available reported capacities of vanadium (+5) oxides in aqueous electrolytes.     

Hierarchical Co<Subscript>3</Subscript>O<Subscript>4</Subscript>@C hollow microspheres with high capacity as an anode material for lithium-ion batteries

Three-dimensional hierarchical Co₃O₄@C hollow microspheres (Co₃O₄@C HSs) are successfully fabricated by a facile and scalable method. The Co₃O₄@C HSs are composed of numerous Co₃O₄ nanoparticles uniformly coated by a thin layer of carbon. Due to its stable 3D hierarchical hollow structure and uniform carbon coating, the Co₃O₄@C HSs exhibit excellent electrochemical performance as an anode material for lithium-ion batteries (LIBs). The Co₃O₄@C HSs electrode delivers a high reversible specific capacity, excellent cycling stability (1672 mAh g^?1 after 100 cycles at 0.2 A g^?1 and 842.7 mAh g^?1 after 600 cycles at 1 A g^?1), and prominent rate performance (580.9 mAh g^?1 at 5 A g^?1). The excellent electrochemical performance makes this 3D hierarchical Co₃O₄@C HS a potential candidate for the anode materials of the next-generation LIBs. In addition, this simple synthetic strategy should also be applicable for synthesizing other 3D hierarchical metal oxide/C composites for energy storage and conversion.     

Improving the electrochemical performance of Li-rich Li<Subscript>1.2</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>Mn<Subscript>0.54</Subscript>O<Subscript>2</Subscript> cathode material by LiF coating

To suppress the capacity fade of Li-rich Li_1.2Ni_0.13Co_0.13Mn_0.54O₂ material as cathode materials for lithium-ion battery, we introduce a LiF coating layer on the surface to improve the cycling performance of Li_1.2Ni_0.13Co_0.13Mn_0.54O₂ material. The modified sample shows a capacity of 163.2 mAh g^?1 with a capacity retention of 95% after 100 cycles at a current density of 250 mA g^?1, while the pristine sample only delivers a capacity of 129.9 mAh g^?1 with a capacity retention of 82%. Compared with the pristine material, the LiF-modified sample exhibits an obvious enhancement in the electrochemical performance, which will be very beneficial for this material to be commercialized on the new energy vehicles and other related areas.     

Simple microwave synthesis and improved electrochemical performance of Nb-doped MnO<Subscript>2</Subscript>/reduced graphene oxide composite as anode material for lithium-ion batteries

Niobium-doped MnO₂/reduced graphene oxide (Nb-MnO₂/RGO) composite has been successfully synthesized via a simple microwave radiation method. The samples were systematically studied by X-ray diffraction (XRD), thermogravimetric analysis (TG), X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM), transmission electron microscope (TEM), and electrochemical measurements. As the anode material for lithium-ion batteries, the Nb-MnO₂/RGO (molar ratio of Mn/Nb?=?50:1) (NMG50) showed an outstanding reversible discharge capacity of 556.6 mAh g^?1 after 50 cycles with a capacity retention of 77% at a charge-discharge rate of 0.1 A g^?1 and the reversible discharge capacity can still retain 223.3 mAh g^?1 at a current of 1 A g^?1, which is much higher than those for Nb-MnO₂/RGO (molar ratio of Mn/Nb?=?10:1) (NMG10) and undoped MnO₂/RGO (MG). The improved electrochemical performance could be attributed to the proper amount of Nb doping, which could enhance both the conductivity and the structure stability of MnO₂.     

Preparation of Co<Subscript>3</Subscript>O<Subscript>4</Subscript> hollow microsphere/graphene/carbon nanotube flexible film as a binder-free anode material for lithium-ion batteries

A flexible Co₃O₄ hollow microsphere/graphene/carbon nanotube hybrid film is successfully prepared through a facile filtration strategy and a subsequent thermally treated process. The composition, morphology, and structure of the as-prepared film are characterized by X-ray diffraction, X-ray photoelectron spectrometer, scanning electron microscopy, and transmission electron microscopy. Based on the morphology characterizations on the hybrid film, the Co₃O₄ hollow microspheres are uniformly and closely attached on three-dimensional (3D) graphene/carbon nanotubes (GR/CNTs) network, which decreases the agglomeration of Co₃O₄ microspheres effectively. In this hybrid film, the 3D GR/CNT network which enhances conductance as well as prevents aggregation is a benefit to help Co₃O₄ to exert its lithium storage capabilities sufficiently. When used as a binder-free anode material for lithium-ion batteries, the hybrid film delivers excellent electrochemical properties involving reversible capacity (863 mAh g^?1 at a current density of 100 mA g^?1) and rate performance (185 mAh g^?1 at a current density of 1600 mA g^?1).     

Facile synthesis of N-doped carbon-coated Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> anode for application in high-rate lithium ion batteries

A facile sol-gel approach for the synthesis of lithium titanate composite decorated with N-doped carbon material (LTO/NC) is proposed. Urea is used as a nitrogen source in the proposed approach. The LTO/NC exhibits superior electrochemical performances as an electrode material for lithium-ion batteries, delivering a discharge capacity of as high as 103 mAh g^?1 at a high rate of 20 C and retaining a stable reversible capacity of 90 mAh g^?1 after 1000 cycles, corresponding to 100% capacity retention. These excellent electrochemical performances are proved by the nanoscale structure and N-doped carbon coating. NC layers were uniformly dispersed on the surface of LTO, thus preventing agglomeration, favoring the rapid migration of the inserted Li ion, and increasing the Li⁺ diffusion coefficient and electronic conductivity. LTO with the appropriate amount of NC coating is a promising anode material with applications in the development of high-powered and durable lithium-ion batteries.     

Synthesis and performance of Li2NiTi3O8 as a new anode material for lithium-ion batteries

The titanate spinel Li₂NiTi₃O₈ is proposed for the first time as a new anode for lithium-ion batteries and successfully synthesized via a facile ball-milling assisted solid-state reaction method. The sample is characterized by X-ray diffraction patterns (XRD), scanning electron microscope (SEM), transmission electron microscopy (TEM), galvanostatic charge–discharge tests, cyclic voltammetry (CV) tests, and electrochemical impedance spectroscopy (EIS). The results reveal that the Li₂NiTi₃O₈ nanoparticles have well-distributed morphology, and the particle size ranges between 100 and 300 nm. Although the initial coulombic efficiency is only 56.3 %, the Li₂NiTi₃O₈ electrode still exhibits a high rate capability and excellent cycling stability. The Li₂NiTi₃O₈ anode provides a large capacity of 212.3 mAh g^?1 at 0.1 A g^?1 after 10 cycle, which is close to its theoretical capacity (223.6 mAh g^?1). Even after 100 cycles, it still delivers a quite high capacity of 203.98 mAh g^?1, with no significant capacity fading. This indicates that the as-synthesized Li₂NiTi₃O₈ material is a promising anode material for lithium-ion batteries.     

PAN-based carbon fiber@SnO<Subscript>2</Subscript> for highly reversible structural lithium-ion battery anode

The carbon fiber (CF) is frequently preferred because it is considered as a multifunctional lightweight composite, where the CF is not only acted as one completely integrated part of the device with high-performance structural reinforcement, but also served as one of the battery electrode to storage energy. However, the limitation of electrochemical capacity of commercial CFs for the structural lithium-ion battery (SLIB) is an urgent issue should be solved. Therefore, in this work, a novel strategy to fabricate CF@SnO₂ composite is developed by employing one-step tin tetrachloride solvothermal method. The performance of the CFs could be improved by growing the stannic oxide firmly on each CF to form a synergetic electrode. When tested as anode materials, a high reversible capacity of 510 mAh g^?1 at a current density of 100 mAh g^?1 is maintained without obvious decay up to 150 cycles (a huge increase as high as 637.5% than that of the pure CFs). Furthermore, our strategy reveals an attainable route, which could be as a promising way to make a sustainable anode for SLIBs and carbon-based multi-functional composite for other practical applications.     

Synthesis and electrochemical investigation of highly dispersed ZnO nanoparticles as anode material for lithium-ion batteries

Highly dispersed ZnO nanoparticles were prepared by a versatile and scalable sol-gel synthetic technique. High-resolution transmission electronic microscopy (HRTEM) showed that the as-prepared ZnO nanoparticles are spherical in shape and exhibit a uniform particle size distribution with the average size of about 7 nm. Electrochemical properties of the resulting ZnO were evaluated by galvanostatic discharge/charge cycling as anode for lithium-ion battery. A reversible capacity of 1652 mAh g^?1 was delivered at the initial cycle and a capacity of 318 mAh g^?1 was remained after 100 cycles. Furthermore, the system could deliver a reversible capacity of 229 mAh g^?1 even at a high current density of 1.5 C. This outstanding electrochemical performance could be attributed to the nano-sized features of highly dispersed ZnO particles allowing for the better accommodation of large strains caused by particle expansion/shrinkage along with providing shorter diffusion paths for Li⁺ ions upon insertion/deinsertion.     

The facile in situ preparation and characterization of C/FeOF/FeF<Subscript>3</Subscript> nanocomposites as LIB cathode materials

C/FeOF/FeF₃ nanocomposite was synthesized by a facile in situ partial oxidation method. High-resolution transmission electron microscopy (HR-TEM) showed a special texture comprised of interpenetrating nanodomains of FeOF and FeF₃. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) measurements revealed that the introduction of nanodomain FeOF enhanced both the electronic and ionic conductivity of the composite material. Therefore, the improvement of electron and lithium-ion dynamics resulted in the significant enhancement of the electrochemical performances of the material at ambient temperature. At a current density of 20 mA g^?1 within potential range 1.5–4.5 V, the specific capacities of the first ten circles were maintained at about 400 mAh g^?1 _. This material also exhibited excellent cycling capacity retention capability especially for high C rates. When the current density further increased to 100 and 200 mA g^?1, a steady capacity of 80 and 60 mAh g^?1 was observed, respectively. Furthermore, nearly no capacity loss was observed for the followed cycles. The discharge platforms based on intercalation and conversion reaction were also heightened by about 0.4 V, which increased the contribution of high voltage capacities. Compared to C/FeF₃, C/FeOF/FeF₃ is showing more of capacitive behavior, which also contributes to the high specific capacity delivered and is believed to be closely related to the enlarged nanodomain interfaces between two electrochemical active materials. An expansion-cracking-oxidation mechanism was proposed to explain the formation of this interpenetrating nanodomains of FeOF and FeF₃.     

Preparation of carbon encapsulated Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> anode material for lithium ion battery through pre-coating method

Carbon encapsulated Li₄Ti₅O₁₂ (C/Li₄Ti₅O₁₂) anode material for lithium ion battery was prepared by using the pre-coat method of two steps, and the TiO₂ was pre coated before the reaction with Li₂CO₃. The structure and morphology of the resultant C/Li₄Ti₅O₁₂ materials were characterized by X-ray diffraction (XRD) and scanning microscopy (SEM). Electrochemical tests showed that at 0.1 C, the initial discharge capacity was 169.9 mAh g^?1, and the discharge capacity was 80 mAh g^?1 at 5 C. After 100 cycles at 2 C, the discharge specific capacity was 108.5 mAh g^?1. Compare with one step coating method, results showed the C/Li₄Ti₅O₁₂ prepared by pre-coat method can reduce the particle’s size and effectively improve the electrochemical performance.     

Fabrication and electrochemical investigation of Li<Subscript>0.5</Subscript>TiO<Subscript>2</Subscript> as anode materials for lithium ion batteries

Hexagonal and cubic Li_0.5TiO₂ particles have been fabricated through magnesiothermic reduction of Li₂TiO₃ particles in a temperature range of 600 to 640 °C. The prolonged reduction time results in lattice transition from hexagonal to cubic structure of Li_0.5TiO₂. Their microstructures, valance state, chemical composition, as well as electrochemical performance as anode candidates for lithium ion batteries have been characterized and evaluated. The hexagonal Li_0.5TiO₂ exhibits better electrochemical activity compared with the cubic one. Further, the carbon-coated hexagonal Li_0.5TiO₂ displays improved electrochemical performance with initial reversible capacity of 176.6 mAh g^?1 and excellent cyclic behavior except capacity fading in the initial 10 cycles, which demonstrate a novel anode candidate for long lifetime lithium ion batteries.     

Hierarchical Mn<Subscript>1.5</Subscript>Co<Subscript>1.5</Subscript>O<Subscript>4</Subscript> microspheres constructed from one-dimensional nanorods as high-performance anode material for lithium-ion battery

Mn_1.5Co_1.5O₄ hierarchical microspheres have been successfully synthesized via a solvothermal method and an annealing procedure. Mn_1.5Co_1.5O₄ exhibits advanced cycling performance, and it retains a reversible capacity of 633 mA h g^?1 at a current density of 400 mA g^?1 with a coulombic efficiency of 99.0% after 220 cycles. Its remarkable performance is attributed to the hierarchical structure assembled with nanorods, which increases the contact area between each nanorod and electrolyte. More significantly, the open space between neighboring nanorods and the pores on the surface of nanorods can improve Li⁺ ion diffusion rate. Furthermore, the nanorods have rapid one-dimensional Li⁺ diffusion channels, which not only possess a large specific surface area for high activity but accommodate the volume change during lithiation–delithiation processes. Therefore, Mn_1.5Co_1.5O₄ hierarchical microspheres can act as a promising alternative anode material for lithium-ion battery.