Enhanced electrochemical performance of Cu<Subscript>2</Subscript>O-modified Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> anode material for lithium-ion batteries

Li₄Ti₅O₁₂/Cu₂O composite was prepared by ball milling Li₄Ti₅O₁₂ and Cu₂O with further heat treatment. The structure and electrochemical performance of the composite were investigated via X-ray diffraction, scanning electron microscopy, energy-dispersive spectroscopy, cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge–discharge tests. Li₄Ti₅O₁₂/Cu₂O composite exhibited much better rate capability and capacity performance than pristine Li₄Ti₅O₁₂. The discharge capacity of the composite at 2 C rate reached up to 122.4 mAh g^?1 after 300 cycles with capacity retention of 91.3 %, which was significantly higher than that of the pristine Li₄Ti₅O₁₂ (89.6 mAh g^?1). The improvement can be ascribed to the Cu₂O modification. In addition, Cu₂O modification plays an important role in reducing the total resistance of the cell, which has been demonstrated by the electrochemical impedance spectroscopy analysis.     

Investigation of the structural and electrochemical performance of Li<Subscript>1.2</Subscript>Ni<Subscript>0.2</Subscript>Mn<Subscript>0.6</Subscript>O<Subscript>2</Subscript> with Cr doping

Cr-doped layered oxides Li[Li_0.2Ni_0.2???x Mn_0.6???x Cr_2x ]O₂ (x?=?0, 0.02, 0.04, 0.06) were synthesized by co-precipitation and high-temperature solid-state reaction. The materials were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (TRTEM), X-ray photoelectron spectroscopy (XPS), and electrochemical impedance spectroscopy (EIS). XRD patterns and HRTEM results indicate that the pristine and Cr-doped Li_1.2Ni_0.2Mn_0.6O₂ show the layered phase. The Li_1.2Ni_0.16Mn_0.56Cr_0.08O₂ shows the best electrochemical properties. The first discharge specific capacity of Li_1.2Ni_0.16Mn_0.56Cr_0.08O₂ is 249.6 mA h g^?1 at 0.1 C, while that of Li_1.2Ni_0.2Mn_0.6O₂ is 230.4 mA h g^?1. The capacity retaining ratio of Li_1.2Ni_0.16Mn_0.56Cr_0.08O₂ is 97.9% compared with 93.9% for Li_1.2Ni_0.2Mn_0.6O₂ after 80 cycles at 0.2 C. The discharge capacity of Li_1.2Ni_0.16Mn_0.56Cr_0.08O₂ is 126.2 mA h g^?1 at 5.0 C, while that of the pristine Li_1.2Ni_0.2Mn_0.6O₂ is about 94.5 mA h g^?1. XPS results show that the content of Mn³⁺ in the Li_1.2Ni_0.2Mn_0.6O₂ can be restrained after Cr doping during the cycling, which results in restraining formation of spinel-like structure and better midpoint voltages. The lithium-ion diffusion coefficient and electronic conductivity of Li_1.2Ni_0.2Mn_0.6O₂ are enhanced after Cr doping, which is responsible for the improved rate performance of Li_1.2Ni_0.16Mn_0.56Cr_0.08O₂.     

Pr-modified Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> nanofibers as an anode material for lithium-ion batteries with outstanding cycling performance and rate performance

Pr-doped Li₄Ti₅O₁₂ in the form of Li_4?x/3Ti_5?2x/3Pr_xO₁₂ (x = 0, 0.01, 0.03, 0.05, and 0.07) was synthesized successfully by an electrospinning technique. ICP shows that the doped samples are closed to the targeted samples. XRD analysis demonstrates that traces of Pr³⁺ can enlarge the lattice parameter of Li₄Ti₅O₁₂ from 8.3403 to 8.3765 Å without changing the spinel structure. The increase of lattice parameter is beneficial to the intercalation and de-intercalation of lithium-ion. XPS results identify the existence form of Ti is mainly Ti⁴⁺ and Ti³⁺ in minor quantity in Li_4?x/3Ti_5?2x/3Pr_xO₁₂ (x = 0.05) samples due to the small amount of Pr³⁺. The transition from Ti⁴⁺ to Ti³⁺ is conducive to the electronic conductivity of Li₄Ti₅O₁₂. FESEM images show that all the nanofibers are well crystallized with a diameter of about 200 nm and distributed uniformly. The results of electrochemical measurement reveal that the 1D Li_4?x/3Ti_5?2x/3Pr_xO₁₂ (x = 0.05) nanofibers display enhanced high-rate capability and cycling stability compared with that of undoped nanofibers. The high-rate discharge capacity of the Li_4?x/3Ti_5?2x/3Pr_xO₁₂ (x = 0.05) samples is excellent (101.6 mAh g^?1 at 50 °C), which is about 58.48 % of the discharge capacity at 0.2 °C and 4.3 times than that of the bare Li₄Ti₅O₁₂ (23.5 mA g^?1). Even at 10 °C (1750 mA g^?1), the specific discharge capacity is still 112.8 mAh g^?1 after 1000 cycles (87.9 % of the initial discharge capacity). The results of cyclic voltammograms (CV) and electrochemical impedance spectroscopy (EIS) illustrate that the Pr-doped Li₄Ti₅O₁₂ electrodes possess better dynamic performance than the pure Li₄Ti₅O₁₂, further confirming the excellent electrochemical properties above.     

Preparation of carbon encapsulated Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> anode material for lithium ion battery through pre-coating method

Carbon encapsulated Li₄Ti₅O₁₂ (C/Li₄Ti₅O₁₂) anode material for lithium ion battery was prepared by using the pre-coat method of two steps, and the TiO₂ was pre coated before the reaction with Li₂CO₃. The structure and morphology of the resultant C/Li₄Ti₅O₁₂ materials were characterized by X-ray diffraction (XRD) and scanning microscopy (SEM). Electrochemical tests showed that at 0.1 C, the initial discharge capacity was 169.9 mAh g^?1, and the discharge capacity was 80 mAh g^?1 at 5 C. After 100 cycles at 2 C, the discharge specific capacity was 108.5 mAh g^?1. Compare with one step coating method, results showed the C/Li₄Ti₅O₁₂ prepared by pre-coat method can reduce the particle’s size and effectively improve the electrochemical performance.     

Electrospinning preparation of one-dimensional Co<Superscript>2+</Superscript>-doped Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> nanofibers for high-performance lithium ion battery

One-dimensional Co²⁺-doped Li₄Ti₅O₁₂ nanofibers with a diameter of approximately 500 nm have been synthesized via a one-step controllable electrospinning method. The Co²⁺-doped Li₄Ti₅O₁₂ nanofibers were systematically characterized by XRD, ICP, TEM, SEM, BET, EDS mapping, and XPS. Based on the cubic spinel structure and one-dimensional effect of Li₄Ti₅O₁₂, Co²⁺-doped Li₄Ti₅O₁₂ nanofibers exhibit the enlarged lattice volume, reduced particle size and enhanced electrical conductivity. More importantly, Co²⁺-doped Li₄Ti₅O₁₂ nanofibers as a lithium ion battery anode electrode performs superior electrochemical performance than undoped Li₄Ti₅O₁₂ electrode in terms of electrochemical measurements. Particularly, the reversible capacity of Co²⁺-doped Li₄Ti₅O₁₂ electrode reaches up to 140.1 mAh g^?1 and still maintains 136.5 mAh g^?1 after 200 cycles at a current rate of 5 C. Therefore, one-dimensional Co²⁺-doped Li₄Ti₅O₁₂ nanofiber electrodes, showing high reversible capacity and remarkable recycling property, could be a potential candidate as an anode material.     

Improved electrochemical properties of YF<Subscript>3</Subscript>-coated Li<Subscript>1.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>O<Subscript>2</Subscript> as cathode for Li-ion batteries

Yttrium fluoride YF₃ layer with different coating contents is successfully covered on the surface of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ via a common wet chemical approach. The XRD, SEM, TEM, and charge-discharge tests are applied to investigate the influence of YF₃ layer on the micro-structural, morphology, and electrochemical properties of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂. And the electrochemical test results demonstrate that the YF₃-coated LMNCO samples exhibit the improved electrochemical properties. The 2wt.%YF₃-coated LMNCO delivers a discharge capacity of 116.6 mAh g^?1 at 5 C rate, much larger than that (95.6 mAh g^?1) of the pristine one. Besides, the electrochemical impedance spectroscopy (EIS) and cyclic voltammetric results indicate that the YF₃ coating layer can promote the optimization formation of SEI film and reversibility of the electrochemical redox.     

Nano Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> as sulfur host for high-performance Li-S battery

S/Li₄Ti₅O₁₂ cathode with high lithium ionic conductivity was prepared for Li-S battery. Herein, nano Li₄Ti₅O₁₂ is used as sulfur host and fast Li⁺ conductor, which can adsorb effectively polysulfides and improve remarkably Li⁺ diffusion coefficient in sulfur cathode. At 0.5 C, S/Li₄Ti₅O₁₂ cathode has a stable discharge capacity of 616 mAh g^?1 at the 700th cycle and a capacity loss per cycle of 0.0196% from the second to the 700th cycle, but the corresponding values of S/C cathode are 437 mAh g^?1 and 0.0598%. Even at 2 C, the capacity loss per cycle of S/Li₄Ti₅O₁₂ cathode is only 0.0273% from the second to the 700th cycle. The results indicate that Li₄Ti₅O₁₂ as the sulfur host plays a key role on the high performance of Li-S battery due to reducing the shuttle effect and enhancing lithium ionic conductivity.     

Electrochemical comparison of LiFe<Subscript>0.4</Subscript>Mn<Subscript>0.595</Subscript>Cr<Subscript>0.005</Subscript>PO<Subscript>4</Subscript>/C and LiMnPO<Subscript>4</Subscript>/C cathode materials

A comparison of electrochemical performance between LiFe_0.4Mn_0.595Cr_0.005PO₄/C and LiMnPO₄/C cathode materials was conducted in this paper. The cathode samples were synthesized by a nano-milling-assisted solid-state process using caramel as carbon sources. The prepared samples were investigated by XRD, SEM, TEM, energy-dispersive X-ray spectroscopy (EDAX), powder conductivity test (PCT), carbon-sulfur analysis, electrochemical impedance spectroscopy (EIS), and galvanostatic charge-discharge cycling. The results showed that LiFe_0.4Mn_0.595Cr_0.005PO₄/C exhibited high specific capacity and high energy density. The initial discharge capacity of LiFe_0.4Mn_0.595Cr_0.005PO₄/C was 163.6 mAh g^?1 at 0.1C (1C = 160 mA g^?1), compared to 112.3 mAh g^?1 for LiMnPO₄/C. Moreover, the Fe/Cr-substituted sample showed good cycle stability and rate performance. The capacity retention of LiFe_0.4Mn_0.595Cr_0.005PO₄/C was 98.84 % over 100 charge-discharge cycles, while it was only 86.64 % for the pristine LiMnPO₄/C. These results indicated that Fe/Cr substitution enhanced the electronic conductivity for the prepared sample and facilitated the Li⁺ diffusion in the structure. Furthermore, LiFe_0.4Mn_0.595Cr_0.005PO₄/C composite presented high energy density (606 Wh kg^?1) and high power density (574 W kg^?1), thus suggested great potential application in lithium ion batteries (LIBs).     

Improving the electrochemical performance of Li-rich Li<Subscript>1.2</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>Mn<Subscript>0.54</Subscript>O<Subscript>2</Subscript> cathode material by LiF coating

To suppress the capacity fade of Li-rich Li_1.2Ni_0.13Co_0.13Mn_0.54O₂ material as cathode materials for lithium-ion battery, we introduce a LiF coating layer on the surface to improve the cycling performance of Li_1.2Ni_0.13Co_0.13Mn_0.54O₂ material. The modified sample shows a capacity of 163.2 mAh g^?1 with a capacity retention of 95% after 100 cycles at a current density of 250 mA g^?1, while the pristine sample only delivers a capacity of 129.9 mAh g^?1 with a capacity retention of 82%. Compared with the pristine material, the LiF-modified sample exhibits an obvious enhancement in the electrochemical performance, which will be very beneficial for this material to be commercialized on the new energy vehicles and other related areas.     

Effects of dopant on the electrochemical properties of Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> anode materials

The effects of dopant on the electrochemical properties of spinel-type Li_3.97M_0.1Ti_4.94O₁₂ (M = Mn, Ni, Co) and Li_(4-x/3)Cr_xTi_(5-2x/3)O₁₂(x = 0.1, 0.3, 0.6, 0.9, 1.5) were systematically investigated. Charge-discharge cycling were performed at a constant current density of 0.5 mA/cm² between the cut-off voltages of 3.0 and 1.0 V, the experimental results showed that Cr³⁺ dopant improved the reversible capacity and cycling stability over the pristine Li₄Ti₅O₁₂. The substitution of the Mn³⁺ and Ni³⁺ slightly decreased the capacity of the Li₄Ti₅O₁₂. Dopants such as Co³⁺ to some extent worsened the electrochemical performance of the Li₄Ti₅O₁₂.     

Preparation and electrochemical properties of Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>/Ti<Subscript>4</Subscript>O<Subscript>7</Subscript> composite for lithium-ion batteries

In order to improve the rate capability of Li₄Ti₅O₁₂, Ti₄O₇ powder was successfully fabricated by improved hydrogen reduction method, then a dual-phase composite Li₄Ti₅O₁₂/Ti₄O₇ has been synthesized as anode material for lithium-ion batteries. It is found that the Li₄Ti₅O₁₂/Ti₄O₇ composite shows higher reversible capacity and better rate capability compared to Li₄Ti₅O₁₂. According to the charge-discharge tests, the Li₄Ti₅O₁₂/Ti₄O₇ composite exhibits excellent rate capability of 172.3 mAh g^?1 at 0.2 C, which is close to the theoretical value of the spinel Li₄Ti₅O₁₂. More impressively, the reversible capacity of Li₄Ti₅O₁₂/Ti₄O₇ composite is 103.1 mAh g^?1 at the current density of 20 C after 100th cycles, and it maintains 84.8% of the initial discharge capacity, whereas that of the bare spinel Li₄Ti₅O₁₂ is only 22.3 mAh g^?1 with a capacity retention of 31.1%. The results indicate that Li₄Ti₅O₁₂/Ti₄O₇ composite could be a promising anode material with relative high capacity and good rate capability for lithium-ion batteries.     

Improved electrochemical performance of Li<Subscript>1.2</Subscript>Ni<Subscript>0.2</Subscript>Mn<Subscript>0.6</Subscript>O<Subscript>2</Subscript> cathode material with fast ionic conductor Li<Subscript>3</Subscript>VO<Subscript>4</Subscript> coating

Layered lithium-enriched nickel manganese oxides Li_1.2Ni_0.2Mn_0.6O₂ have been synthesized and coated by fast ionic conductor Li₃VO₄ with varying amounts (1, 3, and 5 wt%) in this paper. The effect of Li₃VO₄ on the physical and electrochemical properties of Li_1.2Ni_0.2Mn_0.6O₂ has been discussed through the characterizations of X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscope (TEM), discharge, cyclic performance, rate capability, and electrochemical impedance spectroscopy (EIS). The discharge capacity and coulomb efficiency of Li_1.2Ni_0.2Mn_0.6O₂ in the first cycle have been improved after Li₃VO₄ coating. And, the 3 wt% Li₃VO₄-coated Li_1.2Ni_0.2Mn_0.6O₂ shows the best discharge capacity (246.8 mAh g^?1), capacity retention (97.3 % for 50 cycles), and rate capability (90.4 mAh g^?1 at 10 C). Electrochemical impedance spectroscopy (EIS) results show that the R _ct of Li_1.2Ni_0.2Mn_0.6O₂ electrode decreases after Li₃VO₄ coating, which is due to high lithium ion diffusion coefficient of Li₃VO₄, is responsible for superior rate capability.     

Influence of carbon additive on the properties of spherical Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> and LiFePO<Subscript>4</Subscript> materials for lithium-ion batteries

Preparing spherical particles with carbon additive is considered as one effective way to improve both high rate performance and tap density of Li₄Ti₅O₁₂ and LiFePO₄ materials. Spherical Li₄Ti₅O₁₂/C and LiFePO₄/C composites are prepared by spray-drying–solid-state reaction method and controlled crystallization–carbothermal reduction method, respectively. The X-ray diffraction characterization, scanning electron microscope, Brunauer–Emmett–Teller, alternating current impedance analyzing, tap density testing, and electrochemical property measurements are investigated. After hybridizing carbon with a proper quantity, the crystal grain size of active materials is remarkably decreased and the electrochemical properties are obviously improved. The Li₄Ti₅O₁₂/C and LiFePO₄/C composites prepared in this work are spherical. The tap density and the specific surface area are as high as 1.71 g cm⁻³ and 8.26 m² g⁻¹ for spherical Li₄Ti₅O₁₂/C, which are 1.35 g cm⁻³ and 18.86 m² g⁻¹ for spherical LiFePO₄/C powders. Between 1.0 and 3.0 V versus Li, the reversible specific capacity of the Li₄Ti₅O₁₂/C is more than 150 mAh g⁻¹ at 1.0-C rate. Between 2.5 and 4.2 V versus Li, the reversible capacity of the LiFePO₄/C is close to 140 mAh g⁻¹ at 1.0-C rate.     

Thermoeletrochemical study on LiNi<Subscript>0.8</Subscript>Co<Subscript>0.1</Subscript>Mn<Subscript>0.1</Subscript>O<Subscript>2</Subscript> with in situ modification of Li<Subscript>2</Subscript>ZrO<Subscript>3</Subscript>

To improve the electrochemical performance of Nickel-rich cathode material LiNi_0.8Co_0.1Mn_0.1O₂, an in situ coating technique with Li₂ZrO₃ is successfully applied through wet chemical method, and the thermoelectrochemical properties of the coated material at different ambient temperatures and charge-discharge rates are investigated by electrochemical-calorimetric method. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) tests demonstrate that the Li₂ZrO₃ coating decreases the electrode polarizatoin and reduces the charge transfer resistance of the material during cycling. Moreover, it is found that with the ambient temperatures and charge-discharge rates increase, the specific capacity decreases, the amount of heat increases, and the enthalpy change (ΔH) increases. The specific capacity of the cells at 30 °C are 203.8, 197.4, 184.0, and 174.5 mAh g^?1 at 0.2, 0.5, 1.0, and 2.0 C, respectively. Under the same rate (2.0 C), the amounts of heat of the cells are 381.64, 645.32, and 710.34 mJ at 30, 40, and 50 °C. These results indicate that Li₂ZrO₃ coating plays an important role to enhance the electrochemical performance of LiNi_0.8Co_0.1Mn_0.1O₂ and reveal that choosing suitable temperature and current is critical for solving battery safety problem.     

Influence of cooling mode on the electrochemical properties of Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> anode materials for lithium-ion batteries

Li₄Ti₅O₁₂ (LTO) was synthesized with two different cooling methods by solid-state method, namely fast cooling and air cooling. The samples were characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), galvanostatic charge–discharge test, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS), respectively. XRD revealed that the basic LTO structure was not changed. FESEM images showed that fast cooling effectively reduced the particle sizes and the agglomeration of particles. Galvanostatic charge–discharge test showed that the air cooling sample exhibited a mediocre performance, having an initial discharge capacity of 136.3mAh?·?g^?1 at 0.5 C; however, the fast cooling sample demonstrated noticeable improvement in both of its discharge capacity and rate capability, with a high initial capacity value of 142.7 mAh?·?g^?1 at 0.5 C. CV measurements also revealed that fast cooling enhanced the reversibility of the LTO. EIS confirmed that fast cooling resulted in lower electrochemical polarization and a higher lithium-ion diffusion coefficient. Therefore, fast cooling have a great impact on discharge capacity, rate capability, and cycling performance of LTO anode materials for lithium-ion batteries.     

Effects of doping Al on the structure and electrochemical performances of Li[Li<Subscript>0.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>]O<Subscript>2</Subscript> cathode materials

The Li-rich cathode material Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ had been successfully synthesized by a carbonate coprecipitation method. The effects of substituting traces of Al element for different transitional metal elements on the crystal structure and surface morphology had been investigated by X-ray diffraction (XRD) and field emission scanning electron microscopy. The results revealed that all the materials showed similar XRD patterns and surface morphology. It was demonstrated that LNCMAl1 exhibited the superior electrochemical performance. The discharge capacity was 265.2 mAh g^?1 at 0.1 C and still maintained a discharge capacity of 135.6 mAh g^?1 at 5.0 C. The capacity retention could still be 58.2 and 66.8% after 50 cycles at 1.0 and 2.0 C, respectively. Electrochemical impedance spectra results proved that the remarkably improved rate capability and cycling performance could be ascribed to the low charge transfer resistance and enhanced reaction kinetics.     

Improvement of electrochemical performance for AlF<Subscript>3</Subscript>-coated Li<Subscript>1.3</Subscript>Mn<Subscript>4/6</Subscript>Ni<Subscript>1/6</Subscript>Co<Subscript>1/6</Subscript>O<Subscript>2.40</Subscript> cathode materials for Li-ion batteries

Li-rich layered-layered-Spinel structure spherical Li_1.3Mn_4/6Ni_1/6Co_1/6O_2.40 particles was successfully prepared and coated with a uniform layer by a two-step co-precipitation method and evaluated in lithium cells. The structures and electrochemical properties of pristine Li_1.3Mn_4/6Ni_1/6Co_1/6O_2.40 and AlF₃-coated Li_1.3Mn_4/6Ni_1/6Co_1/6O_2.40 were characterized. When the coating amount was 2 wt%, the cathode showed the best cycling performance and rate capability compared to others. The AlF₃-coated Li_1.3Mn_4/6Ni_1/6Co_1/6O_2.40 Li-ion cell cathode had a capacity retention of 90.07 % after 50 cycles at 0.5 C over 2.0–4.8 V, while the pristine Li_1.3Mn_4/6Ni_1/6Co_1/6O_2.40 exhibited capacity retention of only 80.73 %. Moreover, the rate capability and cyclic performance also improved. Electrochemical impedance spectroscopy testing revealed that the improved electrochemical performance might attribute to the AlF₃ coating layer which can suppress the increase of impedance during the charging and discharging process by preventing direct contact between the highly delithiated active material and electrolyte.     

Study on electrochemical performance of Mg-doped Li<Subscript>2</Subscript>FeSiO<Subscript>4</Subscript> cathode material for Li-ion batteries

In this paper, Li₂Fe_1?yMg_ySiO₄/C (y?=?0, 0.01, 0.02, 0.03, 0.05), a cathode material for lithium-ion battery was synthesized by solid-state method and modified by doping Mg²⁺ on the iron site. The effects of Mg²⁺ doping on the crystal structure and electrochemical performance Li₂FeSiO₄ was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), and electrochemical tests. Electrochemical methods of measurement were applied including constant current charge–discharge test, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS), to determine the electrochemical performance of the material and the optimal doping ion and ratio. The results showed that Li₂Fe_0.98Mg_0.02SiO₄/C has the higher specific capacity and better cycle stability as well as lower impedance and better reversibility. The enhanced electrochemical performance can be attributed to the increased electronic conductivity, the decreased charge transfer impedance, and the improved Li-ion diffusion coefficient. Then, further study on the synthesis conditions was performed to find the optimal combustion temperature and time. According to the study, the material which has the best electrochemical performance, shows initial discharge specific capacity of 142.3 mAh g^?1 at 0.1 C (1 C?=?166 mA g^?1) and coulomb efficiency of 95.6%, under the condition that the temperature is 700 °C and the calcining time is 10 h.     

Synthesis and characterization of pristine Li<Subscript>2</Subscript>MnSiO<Subscript>4</Subscript> and Li<Subscript>2</Subscript>MnSiO<Subscript>4</Subscript>/C cathode materials for lithium ion batteries

The cathode materials, pristine Li₂MnSiO₄ and carbon-coated Li₂MnSiO₄ (Li₂MnSiO₄/C), were synthesized by the sol–gel method. Power X-ray diffraction and scanning electron microscopy analyses show that the presence of carbon during synthesis can weaken the formation of impurities in the final product and decrease the particle size of the final product. The effects of carbon coating on electrochemical characteristics were investigated by galvanostatic cycling test and electrochemical impedance spectroscopy. The galvanostatic cycling test results indicate that Li₂MnSiO₄/C cathode exhibits better electrochemical performance with an initial discharge capacity of 134.4 mAh g⁻¹ and a capacity retention of 63.9 mAh g⁻¹ after 20 cycles. Electrochemical impedance analyses confirm that carbon coating can increase electronic conductivity, which results in good electrochemical performance of Li₂MnSiO₄/C cathode. The two semicircles and the large arc obtained in this study can be attributed to the migration of lithium ions through the solid electrolyte interphase films, the electronic properties of the material, and the charge transfer step, respectively.     

Effect of high-temperature crystallization on the electrochemical properties of LiNi<Subscript>0.5</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.3</Subscript>O<Subscript>2</Subscript> synthesized from a lithiated transition metal oxide precursor

The lithiated transition metal oxide precursor (LNCMO) with typical α-NaFeO₂ structure and imperfect crystallinity, obtained from a hydrothermal process, was pretreated at 500 °C and then subjected to sintering at 800–920 °C to synthesize the ternary layered LiNi_0.5Co_0.2Mn_0.3O₂ (NCM523). X-ray diffraction (XRD), scanning electron microscope (SEM), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and charge/discharge testing were used for investigating the effect of the high-temperature crystallization on the properties of the NCM523 cathode materials. The results show that the materials heated at 880–900 °C possess superior cation ordering, perfect crystallinity, and excellent electrochemical performances, among which the material heated at 900 °C delivers better performances, with the initial discharge capacity of 152.6 mAh g^?1 at 0.5 C over 3.0 to 4.3 V and the capacity retention of 95.5% after 50 cycles. Furthermore, the effect of the high-temperature crystallization on the Li⁺ diffusion coefficient, potential polarization, and electrochemical resistance are discussed.