流动注射在线消解测定水中总氮

研究了流动注射在线消解测定水中总氮的自动分析方法。方法基于使用电热和紫外在碱性过硫酸钾体系中消解样品,有机形态和无机形态的氮都被氧化为硝酸盐氮,消解效率为93.0%—108.5%。硝酸盐通过镀铜的镉柱还原为亚硝酸盐,亚硝酸盐与4-对氨基苯磺酰胺、N-（1-萘基）乙二胺盐酸盐形成偶氮染料,在540nm处进行测定。方法的线性范围为20.0—2000.0μg.L-1（r≥0.9995）,检出限为8.3μg.L-1,相对标准偏差为0.8%—1.6%;样品测定频率为35样/h,地表水、地下水、自来水等实际水样的加标回收率为95.9%—107.3%。对于污水样品中的总氮测定FIA与国标方法GB 11894-89对比,无显著差异。     

流动注射化学发光法测定亚硝酸盐

基于亚硝酸盐对高锰酸钾-乙二醛化学发光体系的抑制作用,建立了亚硝酸盐的流动注射化学发光测定方法;在最佳测试条件下,方法对亚硝酸盐的检出限为1×10-9mol,L-1,线性范围为1.0×10-8-1.0×10-3mol,L-1;对1·0×10-6mol,L-1的亚硝酸盐平行测定11次,其RSD为1.3％.该方法可用于测定食品或水中的亚硝酸盐含量.     

N-(1-萘基)-乙二胺荧光光度法测定痕量亚硝酸根

研究了盐酸介质中N-(1-萘基)-乙二胺(NED)与亚硝酸根的反应。基于NED的荧光强度被亚硝酸根猝灭的现象,建立了一种荧光测定NO-₂的新方法,并对反应机理进行了讨论。在优化实验条件下,NO-₂在1.07～214.0 μg·L-1范围内与NED的荧光猝灭强度呈线性关系,方法的检出限为0.069 μg·L-1。该法用于测定水样中痕量亚硝酸根的含量,结果令人满意。     

磺胺-N-苯基J酸分光光度法测定亚硝酸盐研究

筛选了重氮组分和偶合组分。研究了重氮偶合显色反应的条件和方法,提出了借助于磺胺-J酸系列染料中间体(N-苯基J酸、J酸、双J酸)重氮偶合技术分光光度法测定亚硝酸盐。在常温溴化钾共存下,亚硝酸盐在稀盐酸溶液中与磺胺发生重氮化反应,在碳酸钠水溶液中重氮盐与J酸系列染料中间体偶合生成有色偶氮化合物。磺胺-N-苯基J酸偶氮化合物的表观摩尔吸光系数为4.63×104 L·mol-1·cm-1,线性范围为0.003～0.7 mg·L-1,回收率为99.5%～101.6%。相对标准偏差为2.10%。该本方法可用于环境水体中痕量亚硝酸盐的测定。     

N-溴代丁二酰亚胺氧化体系流动注射化学发光法测定水中苯酚

在碱性介质中,N-溴代丁二酰亚胺氧化鲁米诺产生化学发光,苯酚对反应具有很强的抑制作用,据此建立了N-溴代丁二酰亚胺-鲁米诺-苯酚化学发光体系测定水中苯酚的新方法。当苯酚的浓度在1.0×10-5～9.0×10-4 mg·mL-1范围内,其浓度与发光强度呈良好的线性关系, 检出限是1.81×10-7 mg·mL-1, 相对标准偏差为1.11%, 将该方法直接用到水样中苯酚的测定, 取得满意的结果。并探讨了该化学发光反应的机理。     

流动注射化学发光法测定山奈酚

采用流动注射技术,研究了高锰酸钾-山奈酚-过氧化氢体系的化学发光行为,对影响化学发光强度的因素进行了试验,建立了流动注射化学发光法测定山奈酚的新方法.方法检出限为1×10-10g·mL-1,线性范围为1.0×10-7-1.0×10-4g·mL-1.对1.0×10-6g·mL-1的山奈酚平行测定11次,其RSD为2.1%...     

流动注射化学发光法测定芦丁

在酸性介质中,硫酸高铈氧化芦丁能产生弱发光,而罗丹明6G(Rh6G)能大大增强此弱发光,由此建立了流动注射化学发光法测定芦丁的新方法。研究了影响化学发光强度的各种因素,优化了硫酸、硫酸高铈和Rh6G等条件,对样品中可能存在的各种干扰物质进行了研究,并初步探讨了化学发光反应可能的机理。该方法的线性范围为1.0×10-7～1.0×10-4 mol·L-1,方法的检出限为8.1×10-8 mol·L-1,对1.0×10-5 mol·L-1的芦丁进行11次平行测定,其相对标准偏差为1.5%,回收率为99.0%～104.0%。该方法应用于芦丁片剂中芦丁含量的测定,取得了满意的结果。     

用吐温80-硫酸铵-水体系的液-固萃取光度法测定痕量镍

研究了Ni()-PAR在吐温80-硫酸铵-水体系中的最佳萃取条件,建立了水样中测定痕量镍的非有机溶剂液-固萃取光度法。在NH3·H2O-NH4Cl缓冲溶液中,金属配合物Ni()-PAR可被吐温80固相富集萃取,最大吸收波长为500nm,镍含量在0—1.0μg/mL范围内服从朗伯-比耳定律,表观摩尔吸光系数为6.345×104L·mol-1·cm-1。该法测定水样中镍含量,回收率可达96.3%—103.0%。     

基于荧光分析技术的大鼠肠灌流液中H_2S含量测定

荧光素汞在碱性条件下具有很强的荧光,H2S能与荧光素汞结合,使其荧光猝灭,据此建立了一种荧光法测定大鼠肠灌流液中H2S含量的方法。在0.1mol·L-1 NaOH溶液中,以Na2S作为H2S供体,荧光素汞浓度为5.0×10-5 mol·L-1,Na2S浓度为1.0×10-5 mol·L-1时,以498nm为激发波长,在522nm处测定此二元体系的荧光强度。结果表明,在4.0×10-7~2.0×10-6 mol·L-1范围内,H2S浓度与荧光强度的下降程度呈良好的负相关性,r=0.998 0,精密度实验RSD=4.59%(n=7),检出限3.5×10-8 mol·L-1,样品中H2S含量分别为1.01×10-6和1.15×10-6 mol·L-1,加标回收率为95.8%~101.0%。该方法操作简单,灵敏度高,稳定性好,可准确测定肠灌流液中H2S含量,为内源性H2S的测定提供了依据。     

电解分离-ICP-AES测定铜-银-磷钎料中的磷

采用电解法分离铜后,电感耦合等离子体-原子发射光谱法直接测定了铜-银-磷钎料中磷的含量。实验表明,在1.0moI·L^-1硝酸电解液中可以使铜基本电离完全,对磷的测定不产生干扰。在最佳的测定条件下,该法用于铜-银-磷钎料中磷的测定,回收率在98.3%—102.4%之间,相对标准偏差2.28%。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.