Deductive prediction of measurement precision and optimization of integration time and wavelength in capillary electrophoreses

Summary This paper demonstrates that the relative standard deviation (RSD) of measurements in a capillary electrophoresis system can be predicted theoretically from the baseline and the signal shape at low sample concentration. The only requirements for prediction of the uncertainty are the Fourier transform of the baseline (here 2048 data points) and the observation of signal shape. The micellar electrokinetic chromatography (MEKC) of acetaminophen and caffeine is taken as an example. The optimum is defined here as the condition of the lowest RSD or highest precision. The optimum single wavelength is selected from between 220 and 350 nm for the MEKC system equipped with a photodiode array detector. The optimum time domain of signal integration is shown to be even narrower than the entire signal region, providing an RSD value about half that for integration of the entire region. The theory is in good agreement with observed RSD values.     

Signal-to-noise considerations for rapid scan atomic spectrometry with an inductively coupled plasma

The blank photon flux from an ICP is measured with a conventional 1-m spectrometer for the spectral region from 200 to 450 nm. This flux is then used to calculate the minimum integration time required before quantum noise (shot noise from the photon flux) becomes significant under various conditions. The calculations demonstrate that blank integration times may be much shorter than the times spent integrating either samples or standards without degradation of the total measurement. Comparison to extrapolated values for a high resolution spectrometer configuration indicate that minimum integration times requirements will vary drastically with wavelength, slit width and spectrometer configuration. The data demonstrates that integration times may be as short as l ms under certain circumstances indicating that very rapid scan data acquisition is feasible for ICP-AES if done with intelligent interactive control.     

Systematic HPLC Study of a New Series of 4-Methyl-1,4-dihydropyridines with Antitrombotic Activity

Abstract

A systematic study of a new series of 4-methyl-1,4-dihydropyridine derivatives by HPLC by both photodiode array and electrochemical detectors is reported.

The optimum mobile phase was acetonitrile 0.05 M phosphate buffer pH 3 (55/45, v/v) at a flow-rate of 1.5 mL/min.

Compounds I–VIII were determined with UV detection at 250 nm and by electrochemical detection at + 1200 mV.

Retention times varied between 3.0 and 14.0 minutes in the optimal experimental conditions.

Good linear relationships between the peak areas and concentration were found, with limits of quantification ranging between 1 x 10^?8 M and 1 x 10^?6 M. Repeatability studies showed average variation coefficients lower than 1% for a photodiode array detector. No significant differences between the detectors in sensitivity and selectivity were found.

Also, we used different degradation trials to test the selectivity of the methods. Results of these experiments revealed that the developed methods exhibited a good selectivity.     

Use of a spectrally segmented photodiode-array spectrometer for inductively coupled plasma atomic-emission spectroscopy Examination of procedures for the evaluation of detection limits

The utility of a spectrally segmented photodiode array spectrometer was examined by using inductively coupled plasma atomic-emission spectrometry (ICP-AES). The spectrometer used in this study is capable of high resolution (reciprocal linear dispersion of approximately 0.08 nm/mm at 300 nm) over a wide spectral range (190-415 nm). The effect of using spectral peak areas instead of peak heights as a signal definition was examined by using the emission signals from 10 molybdenum lines obtained with various photodiode-array integration periods. In addition, a procedure to determine the detection limits obtainable with such a spectrometer is proposed. It was found that a signal definition involving a summation over a range of 5 pixels offered the best signal-to-noise ratio when the noise was defined as the standard deviation of the residual values from the line fitted to the sideband background level. A detection limit of 6 ng/ml was determined in this way for molybdenum. The multichannel capability of the spectrometer was found to permit continuous background correction, thereby reducing errors caused by low-frequency noise or plasma drift. The linearity of response was found to extend over three orders of magnitude with use of a single integration period. However, by use of different integration periods, the linear range of the detector could be extended to at least four orders of magnitude. The precision (RSD) of the spectrometer for a molybdenum concentration of 0.5 mug/ml was found to be about 3-4% for molybdenum peaks where the background emission was relatively low.     

Development and validation of a stability-indicating LC method for the assay of lodenafil carbonate in tablets

A stability-indicating liquid chromatographic method has been developed for the quantitative determination of lodenafil carbonate in tablets. The method employs a Synergi Fusion C18 column (250 × 4.6 mm, i.d., 4 μm particle size), with mobile phase consisting of a mixture of methanol-acetic acid 0.1% pH 4.0 (65:35, v/v) and UV detection at 290 nm, using a photodiode array detector. A linear response (r = 0.9999) was observed in the range of 10-80 μg/mL. The method showed good recoveries (average 100.3%) and also intra and inter-day precision (RSD < 2.0%). Validation parameters as specificity and robustness were also determined. Specificity analysis showed that no impurities or degradation products were co-eluting with the lodenafil carbonate peak. The method was found to be stability-indicating and due to its simplicity and accuracy can be applied for routine quality control analysis of lodenafil carbonate in tablets.     

Use of a novel array detector for the direct analysis of solid samples by laser ablation inductively coupled plasma sector-field mass spectrometry

The use of laser ablation (LA) as a sample-introduction method for inductively coupled plasma mass spectrometry (ICP-MS) creates a powerful tool for trace elemental analysis. With this type of instrument, high analyte spatial resolution is possible in three dimensions with ng/g limits of detection and minimal sample consumption. Here, simultaneous detection is used to eliminate the correlated noise that plagues the ablation process. This benefit allows analyses to be performed with single laser pulses, resulting in improved depth resolution, even less sample consumption, and improved measurement precision. The new instrument includes an LA sample-introduction system coupled to an ICP ionization source and a Mattauch-Herzog mass spectrograph (MHMS) fitted with a novel array detector. With this instrument, absolute limits of detection are in the tens to hundreds of fg regime and isotope-ratio precision is better than 0.02% RSD with a one-hour integration period. Finally, depth-profile analysis has been performed with a depth resolution of 5 nm per ablation event.     

High-Resolution continuum-source atomic absorption spectrometry in an inductively coupled plasma with photodiode array detection

Atomic absorption spectrometry (AAS) is a well established technique using flames and graphite furnaces. An inductively coupled plasma (ICP), however, is an attractive alternative atom/ion reservoir. A high-resolution continuum-source atomic absorption spectrometer with a photodiode array detector and an ICP as the atomization/ionization reservoir is described. Multi-wavelength capability permits the simultaneous determination of several elements by their atomic and/or ionic transitions. Each acquired spectrum is averaged for 10 s to improve the signal-to-noise ratios. Detection limits are calculated for 14 elements and compared with literature values.     

Excitation temperature and electron density in the inductively coupled plasma—aqueous vs organic solvent introduction

Using a photodiode array spectrometer, spatially resolved Fe I, excitation temperatures and electron densities have been measured for an ICP with both water and xylene solution introduction. The excitation temperature is lower in the ICP with organic aerosol than in the ICP with aqueous aerosol at a fixed power and height. For an ICP with organic aerosol the input power must be increased by approx. 0.5 kW to simulate the temperatures reached in an aqueous ICP.     

Separation, characterization, and quantitation of process-related substances of the anti-hypertensive drug doxazosin mesylate by reversed-phase LC with PDA and ESI-MS as detectors

A simple and rapid reversed-phase liquid chromatography (LC) method with photodiode array (PDA) and electrospray ionization (ESI)-mass spectrometry (MS) as detectors was developed and validated to separate, identify, and quantitate the related substances of Doxazosin mesylate (DXZN) for monitoring the reactions involved during process development. The high-performance liquid chromatography profiles of related-substances of DXZN are used as fingerprints to follow the procedures used in the manufacturing units. The separation is accomplished on an Inertsil ODS-3 column with acetonitrile-ammonium acetate (10 mM, pH 4.0) as the mobile phase, using a gradient elution mode and monitoring the eluents by a photodiode array detector at 265 nm at ambient temperature. LC-ESI-MS-MS is used to identify the additional impurities formed during the synthesis. The identified impurities were synthesized and characterized by UV, Fourier transform-IR, 1H NMR, and MS data. The detection limits for the impurities are 0.74 - 4.14 x 10(-9) g, and the method is found to be suitable not only for the monitoring of synthetic reactions, but also for quality assurance of DXZN in bulk drugs and formulations.     

Some characteristics of an intensified photodiode array spectrometer system for use in plasma emission spectrometry

A 1024-element silicon photodiode array with a microchannel plate image intensifier was coupled to a Czerny-Turner spectrometer and basic characteristics of the spectrometer system were studied using an Hg lamp, a hollow cathode lamp and a d.c. argon plasma as emission sources. The intensifier proved to be useful to enhance signals without increasing the electronic background. The signal to dark current ratio of the cooled photodiode array was larger than that of a photomultiplier (HTV R457) in the wavelength region above 380 nm. Effects of entrance slit width, integration time per scan and intensifier gain on signal to background ratios and signal to noise ratio are presented and optimum conditions for emission measurements using the system are described.     

新药乌拉地尔含量的高效液相色谱法测定

用高效液相色谱法测定乌拉地尔（urapidil)的含量。采用PhenomenexLUNA C18柱;1％（φ）冰醋酸溶液－甲醇（体积比50：50）为流动相;检测波长为268nm;外标法定量测定,结果显示样品质量浓度在10－200nm/L范围内与峰面积呈良好线性关系,相关系数为0．9999（n-5);平均加标回收率为99．8％。该法操作快捷,重复性好,结果准确可靠,可用于乌拉地尔的质量控制。     

Determination of aliskiren in tablet dosage forms by a validated stability-indicating RP-LC method

A reversed-phase liquid chromatography (RP-LC) method is validated for the determination of aliskiren in tablet dosage form. The LC method is carried out on a Waters XBridge C(18) column (150 × 4.6 mm i.d.), maintained at 25°C. The mobile phase consisted of acetonitrile:water (95:5, v/v)/phosphoric acid (25 mM, pH 3.0) (40:60, v/v), run at a flow rate of 1.0 mL/min, with photodiode array detector set at 229 nm. The chromatographic separation is obtained with aliskiren retention time of 3.68 min, and it is linear in the range of 10-300 μg/mL (r = 0.9999). The limits of detection and quantitation are 2.38 and 7.93 μg/mL, respectively. The specificity and stability-indicating capability of the method are proven through degradation studies, which also showed that there is no interference of the formulation excipients, showing that peak is free from any coeluting peak. The method showed adequate precision, with a relative standard deviation (RSD) values lower than 0.92%. Good values of accuracy were also obtained, with a mean value of 99.55%. Experimental design is used during validation to calculate method robustness. The proposed method is applied for the analysis of the tablet dosage forms, contributing to improve the quality control and to assure the therapeutic efficacy.     

Determination of uranium, iron, copper, and nickel from ore samples by MEKC using N,N'-ethylene bis(salicylaldimine) as complexing reagent

An analytical procedure has been developed for the separation of dioxouranium(VI), iron(III), copper(II), nickel(II), cobalt(II), cobalt(III), palladium(II), and thorium(IV) by MEKC using N,N'-ethylene bis(salicylaldimine) (H(2)SA(2)en) as a complexing reagent with total runtime <4.5 min. SDS was used as micellar medium at pH 8 with sodium tetraborate buffer (0.1 M). An uncoated fused-silica capillary with an effective length of 50 cm x 75 microm id was used with an applied voltage of 30 kV with photodiode array detection at 231 nm. Linear calibrations were obtained within 0.111-1000 microg/mL of each element with LODs within 37-325 ng/mL. The developed method was tested for analysis of uranium ore samples indicating its presence within 103-1789 microg/g with RSD within 0.79-1.87%. Likewise copper, nickel, and iron in their combined matrix were also simultaneously determined with RSD 0.4-1.6% (n = 6).     

高效液相色谱-二极管阵列检测法测定白首乌中的4种苯乙酮类成分

建立了白首乌中4种苯乙酮类化合物(Ⅰ:4-羟基苯乙酮,Ⅱ:2,5-二羟基苯乙酮,Ⅲ:白首乌二苯酮,Ⅳ:2,4-二羟基苯乙酮)的高效液相色谱检测方法。采用Symmetry-C18色谱柱(4.6 mm×250 mm,5 μm)分离,流动相为甲醇-水(体积比为26∶74),流速1.0 mL/min;采用二极管阵列检测器检测,化合物Ⅰ、Ⅲ、Ⅳ的检测波长为280 nm,化合物Ⅱ的检测波长为224 nm;测定温度为30 ℃。4种苯乙酮类化合物Ⅰ～Ⅳ的线性范围分别为0.080～0.560 μg,0.080～0.560 μg,0.100～0.700 μg和0.092～0.644 μg (r=0.9996～0.9999);平均加样回收率(n=3)为98.0%～104.0%,相对标准偏差为0.8%～2.6%。该方法简便快速、结果准确、重现性好,可作为白首乌药材质量控制的一个有效方法。     

Determination of selenium in blood serum by inductively coupled plasma atomic emission spectrometry with pneumatic nebulization

The possibility of determining selenium in blood serum using inductively coupled plasma emission spectrometry with conventional pneumatic nebulization was studied. A high-resolution spectrometer (SBW=6 pm) with laterally viewed ICP was employed. Analysis with conventional pneumatic nebulization could overcome laborious and demanding digestion, which is necessary for hydride generation. A pressure digestion with nitric acid at 160 degrees C was sufficient to decrease the carbon content in the serum sample to 5%-10% of its original value. Spectral interference of the CN band was observed and mathematically corrected. It was found that the carbon-induced selenium line emission enhancement occurred even under ICP optimized conditions. A method of determination was developed and applied to the analysis of blood serum. True limit of detection in real samples is 0.01-0.02 mg/L and the limit of quantification (RSD 10%) is 0.03-0.07 mg/L using Se I 196.090 nm line at an integration time of 10-2 s. The method was tested by analysis of porcine blood serum and the serum reference material Seronorm MI 0181.     

Development and application of a validated stability-indicating HPLC method for simultaneous determination of granisetron hydrochloride, benzyl alcohol and their main degradation products in parenteral dosage forms

A simple, rapid and sensitive reversed phase high performance liquid chromatographic method using photodiode array detection was developed and validated for the simultaneous determination of granisetron hydrochloride, benzyl alcohol, 1-methyl-1H-indazole-3-carboxylic acid (the main degradation product of granisetron) and benzaldehyde (the main degradation product of benzyl alcohol) in granisetron injections. The separation was achieved on Hypersil BDS C8 (250 mm × 4.6 mm i.d., 5 μm particle diameter) column using a mobile phase consisted of acetonitrile:0.05 M KH₂PO₄:triethylamine (22:100:0.15) adjusted to pH 4.8. The column was maintained at 25 °C and 20 μL of solutions was injected. Photodiode array detector was used to test the peak purity and the chromatograms were extracted at 210 nm. Naphazoline hydrochloride was used as internal standard. The method was validated with respect to specificity, linearity, accuracy, precision, limit of quantitation and limit of detection. The validation acceptance criteria were met in all cases. Identification of the pure peaks was carried out using library match programmer and wavelengths of derivative optima of the spectrograms of the peaks. The method was successfully applied to the determination of the investigated drugs and their degradation products in different batches of granisetron injections. The method was proved to be sensitive for the determination down to 0.03 and 0.01% of granisetron degradation product and benzaldehyde, respectively, which are far below the compendia limits for testing these degradation products in their corresponding intact drugs.     

Development and application of a validated stability-indicating high-performance liquid chromatographic method using photodiode array detection for simultaneous determination of granisetron, methylparaben, propylparaben, sodium benzoate, and their main degradation products in oral pharmaceutical preparations

A simple, rapid, and sensitive RP-HPLC method using photodiode array detection was developed and validated for the simultaneous determination of granisetron hydrochloride, 1-methyl-1H-indazole-3-carboxylic acid (the main degradation product of granisetron), sodium benzoate, methylparaben, propylparaben, and 4-hydroxybenzoic acid (the main degradation product of parabens) in granisetron oral drops and solutions. The separation of the compounds was achieved within 8 min on a SymmetryShield RP18 column (100 x 4.6 mm id, 3.5 microm particle size) using the mobile phase acetonitrile--0.05 M KH2PO4 buffered to pH 3 using H3PO4 (3+7, v/v). The photodiode array detector was used to test the purity of the peaks, and the chromatograms were extracted at 240 nm. The method was validated, and validation acceptance criteria were met in all cases. The robust method was successfully applied to the determination of granisetron and preservatives, as well as their degradation products in different batches of granisetron oral drops and solutions. The method proved to be sensitive for determination down to 0.04% (w/w) of granisetron degradation product relative to granisetron and 0.03% (w/w) 4-hydroxybenzoic acid relative to total parabens.     

Solid-phase spectrophotometric analysis of natural water with the simultaneous sample preparation and dynamic preconcentration of test components on reagent cellulose matrices

A photocolorimeter was developed; this instrument made it possible to perform sample preparation, to preconcentrate test water components on indicator cellulose matrices, and to simultaneously measure their light absorption. A white light-emitting diode and a Digital color sensor S9706 photodiode, which simultaneously detected red (615 nm), green (540 nm), and blue (465 nm) regions of the spectrum, were used in the instrument. The applicability of the photocolorimeter to the determination of 36 components and characteristics of water was demonstrated. The photocolorimeter was proposed for the simultaneous determination of 20 components at a level of their maximum permissible concentrations for fishery water (RSD < 10%) for 10–15 min.     

Low flow,externally air cooled torch for inductively coupled plasma atomic emission spectrometry with axial viewing

The torch wall is cooled largely by air passing through a cooling jacket added to the outside of a Fassel torch. The plasma is viewed axially through a cooled cone interface centered on the axial channel. The outer argon gas flow can be reduced to 7 l min⁻¹ with no compromise in performance or torch lifetime. The plasma exhibits the same ‘robustness index’ and interference effects from Na as the conventional, high-flow ICP supplied with the particular spectrometer used. Detection limits (DL) for lines at ∼200 nm are poorer by approximately a factor of two, while those for lines at ∼400 nm are actually better than values typically seen for the same lines by axial viewing of a conventional, high-flow ICP.     

Synthesis and electrochemical properties of vanadium pentoxide nanotube arrays

Nanotube arrays of amorphous vanadium pentoxide (V(2)O(5)) were synthesized via template-based electrodeposition, and its electrochemical properties were investigated for Li-ion intercalation applications. The nanotubes have a length of 10 microm, outer diameter of 200 nm and inner diameter of 100 nm. Electrochemical analyses demonstrate that the V(2)O(5) nanotube array delivers a high initial capacity of 300 mAh/g, about twice that of the electrochemically prepared V(2)O(5) film. Although the V(2)O(5) nanotube array shows a more drastic degradation than the film under electrochemical redox cycles, the nanotube array reaches a stabilized capacity of 160 mAh/g, which remains about 1.3 times the stabilized capacity of the film.