Hard carbon derived from corn straw piths as anode materials for sodium ion batteries

Hard carbon is considered as the most promising anode material for practical sodium ion batteries. Herein, we report biomass-derived hard carbon made from corn straw piths through a simple carbonization process. X-ray diffraction patterns and Raman spectra elucidated highly disordered structures, and high-resolution transmission electron microscopy confirmed that the hard carbons have many local ordered structures containing turbostratic nanodomains and more nanovoids surround the turbostratic nanodomains. The electrochemical performances of the hard carbons were systematically investigated in sodium ion batteries. By optimizing the carbonization temperature, the sample carbonized at 1400 °C (HC1400) exhibited high reversible capacity of 310 mAh g^?1 and good cycling stability; the capacity can still retain 274 mAh g^?1 after 100 cycles. More importantly, HC1400 can deliver reversible capacity of 206 mAh g^?1 with 79% retention rate after 700 cycles measured at a current density of 200 mA g^?1, which is much better than those in most previous reports. This study provides a way to develop inexpensive, renewable, and recyclable materials from biomasses towards next-generation energy storage applications.     

Ultrasonic-assisted synthesis of porous S-doped carbon nitride ribbons for photocatalytic reduction of CO2

A series of porous S-doped carbon nitride ribbons (PSCN) were prepared by one-pot hydrothermal and sonochemical synthesis techniques. The morphologies and nanostructures of the catalysts were characterized by SEM, XRD and IR, which confirmed the pristine graphitic structures of carbon nitrides retained in the products. Due to sonication treatment, PSCN has porous structures in the thin ribbon and larger specific surface areas (PSCN 43.5 m²/g, SCN 26.6 m²/g and GCN 6.5 m²/g). XPS and elemental mappings verified that sulfur atoms were successfully introduced into the carbon nitride framework. Diffuse reflectance spectroscopy (DRS) results showed S-doping in the carbon nitride reduced the bandgap energy and enhanced their capability of the utilization of visible light, which contributed to higher photo-generated current. Photoluminescence (PL) analysis indicates the recombination of photogenerated carriers was suppressed in PSCN. Moreover, the photocatalytic performance showed that S-doping and porous and thin ribbon nanostructures may effectively boost the CO₂ reduction rate (to as much as 5.8 times of GCN) when illuminated by visible light (>420 nm) without the need of sacrificial materials. The preliminary mechanisms of the formation of PSCN and its applications in photocatalytic CO₂ reduction are proposed. It highlights the potential of the current technique to produce effective, nonmetal-doped carbon nitride photocatalysts.     

Ultrasound-assisted facile one-pot synthesis of ternary MWCNT/MnO2/rGO nanocomposite for high performance supercapacitors with commercial-level mass loadings

Commercial application of supercapacitors (SCs) requires high mass loading electrodes simultaneously with high energy density and long cycle life. Herein, we have reported a ternary multi-walled carbon nanotube (MWCNT)/MnO₂/reduced graphene oxide (rGO) nanocomposite for SCs with commercial-level mass loadings. The ternary nanocomposite was synthesized using a facile ultrasound-assisted one-pot method. The symmetric SC fabricated with ternary MWCNT/MnO₂/rGO nanocomposite demonstrated marked enhancement in capacitive performance as compared to those with binary nanocomposites (MnO₂/rGO and MnO₂/MWCNT). The synergistic effect from simultaneous growth of MnO₂ on the graphene and MWCNTs under ultrasonic irradiation resulted in the formation of a porous ternary structure with efficient ion diffusion channels and high electrochemically active surface area. The symmetric SC with commercial-level mass loading electrodes (∼12 mg cm⁻²) offered a high specific capacitance (314.6 F g⁻¹) and energy density (21.1 W h kg⁻¹ at 150 W kg⁻¹) at a wide operating voltage of 1.5 V. Moreover, the SC exhibits no loss of capacitance after 5000 charge−discharge cycles showcasing excellent cycle life.     

Simple approach to carboxyl-rich materials through low-temperature heat treatment of hydrothermal carbon in air

It was found that a large number of oxygen-containing functional groups (OFGs) could be created on the surface of hydrothermal carbon (HTC) by simply heating at lower temperature in air during the course of our preliminary experiments which focused on oxidation pre-treatment of pristine HTC for the purpose of grafting functionalization. Especially carboxyl groups on HTC would increase significantly, from 0.53 to 3.70 mmol/g after heat treatment at 300 °C. So, effects of heat-treatment on the OFGs on the carbon microsphere were deeply studied to confirm and explain the findings. Experiments involving different materials (HTC, activated carbon and glucose) were performed under varying conditions (heating temperature and time, in air or in Ar atmosphere). A reaction mechanism for newly generating carboxyl groups on HTC surface during heat-treatment process was supposed based on the results from the sample characterization using Boehm titrations, infrared spectra, X-ray photoelectron spectroscopy, energy dispersive spectrometry and elemental analysis. In addition, the as heat-treated product has excellent sorption capability for Pb²⁺ and Cd²⁺ ions.     

Comparison of different types of polypyrimidine/CNTs/Pt hybrids in fuel cell catalysis

In this paper, we mainly studied the preparation of platinum-containing composite materials with carbon nanotubes wrapped by polypyrimidine-conjugated polymers and the performance of the composites. The polymer-based carbon nanotubes/Pt catalysts were prepared successfully and confirmed by infrared spectroscopy, XPS, XRD, and TEM images. The performance of polypyrimidine/multi-walled carbon nanotubes (MWCNTs)/Pt and polypyrimidine/double-walled carbon nanotubes (DWCNTs)/Pt was compared with the polypyrimidine/single-walled carbon nanotubes (SWCNTs)/Pt. The amount of the loaded Pt on the polypyrimidine/MWCNTs and polypyrimidine/DWCNTs was calculated to be 50.5 wt% and 52.7 wt% respectively. The effective specific surface area of the polypyrimidine/MWCNTs/Pt (45.7 m²/g) and polypyrimidine/DWCNTs/Pt (42.47 m²/g) was observed by electrochemical cyclic voltammetry. These studies strongly imply that the MWCNTs were better candidates than DWCNTs and SWCNTs in the application of polypyrimidine/CNT materials as catalyst for fuel cells.     

Guest-host interaction in energy storage systems

Charge transfer reactions are the most frequent processes met during the conversion of chemical energy into electrical one. Intercalation/insertion processes are the best examples of these phenomena. The type of interaction/binding between guest species and host material decides about the reversibility of the processes. The important drawback of the carbon anode in Li-ion cells is often its irreversible capacity. It correlates with the active surface area and it can be significantly diminished through pyrolytic carbon coating. In situ⁷Li-NMR measurement is a perfect method for monitoring the type of Li-C bonding during the insertion/deinsertion process. Supercapacitor is the second category of attractive energy storage system. The main operation of a capacitor is based on an electrostatic attraction; however, very often pseudocapacitance effects take place. Intensive research is devoted to electrochemical hydrogen storage where the type of C-hydrogen bonding is crucial for practical application of this process. The reversibility of hydrogen insertion into the carbon network is ensured by a weak chemical bonding. Carbon materials with electrosorbed hydrogen play a perfect role of negative electrode in supercapacitor. Attractive host-guest interactions take place during the performance of various supercapacitor electrode materials, e.g. nitrogen-doped carbons with modified electronic structure, layered double hydroxides, conducting polymers, etc.     

Low-density carbon material modified with pyrolytic carbon

Here we report a physicochemical investigation of low-density carbon materials modified with pyrolytic carbon (PC). Exfoliated graphite (EG) obtained by nitrate expandable graphite thermal destruction was pressed into low-density graphite materials (LDGMs) with densities of 0.045-0.50 g/cm³ and saturated with PC by impact CVI technique. LDGM infiltration with PC leads to sample weight and density growth. The amount of deposited PC strictly depends on synthesis conditions. The maximum surface and volume deposition of PC occurred for samples with density of 0.05 g/cm³. XRD, Raman spectroscopy and scanning electron microscopy revealed that the deposited PC is of smooth laminar (SL) type. Composite thermal conductivity is about 2-3.5 Wt/m K.     

氮/硫共掺杂多孔碳纳米片的制备及其电化学性能

二维多孔碳材料能够提供较短的电解质扩散通道和较快的电子传输过程,因此在能量转换和储存装置中表现出优异的电化学性能.近年来的理论和实验研究表明,两元素共掺杂可使二维多孔碳材料的电化学性能得到明显提高.因此,共掺杂二维多孔碳材料的制备成为目前的研究热点之一.本文以甲基橙-FeCl₃复合物为模板引发剂制备了甲基橙掺杂的聚吡咯纳米管,通过对聚吡咯纳米管与KOH混合物（重量比为1：2）在700 ℃进行热处理,制备了二维石墨烯状氮/硫共掺杂多孔碳纳米片.所制备的氮/硫共掺杂多孔碳纳米片相互连结,形成了多级孔结构.氮气吸附分析表明多级孔结构包含微孔、介孔和大孔,这使所制备的氮/硫共掺杂多孔碳纳米片具有较高的比表面积（1744.58 m²/g）和孔体积（1.01 cm³/g）.共掺杂多孔碳纳米片中的掺杂氮以吡啶氮、吡咯氮和季胺氮形式存在,掺杂硫以噻吩硫和氧化态硫形式存在,二者之间的协同效应能够明显改善碳纳米片表面的浸润性,增加表面电化学活性点.这些特征使所制备的氮/硫共掺杂多孔碳纳米片表现出优异的电化学性能.用氮/硫共掺杂多孔碳纳米片制备的量子点敏化太阳能电池对电极,对多硫电解质再生反应的电催化活性与传统PbS对电极相近,所组装电池的光电转换效率可达到4.30%（100 mW/cm²）.氮/硫共掺杂多孔碳纳米片作为超级电容器电极材料,以6 M（1 M=1 mol/L）KOH为电解质,电流密度为0.4 A/g,比电容达到312.8 F/g.即使电流密度增加到20 A/g,比电容仍达到200.6 F/g,表明其具有较好的倍率性能.     

Optimization of Thermal Stability of High-Density Polyethylene Composite Using Antioxidant,Carbon Black and Nanoclay Addition by a Central Composite Design Method: X-ray Diffraction and Rheological Characterization

The thermal stability of high-density polyethylene, as characterized by an Oxidation Induction Time (OIT) test in the presence of the three additives, antioxidant, carbon black and nanoclay, was investigated. The twenty experiments used were designed by using the Central Composite Design (CCD) method, and the effects of the main parameters and their interactions were analyzed. The results of Analysis of Variance (ANOVA) showed that the antioxidant, nanoclay and carbon black contents, the antioxidant-nanoclay interaction and the antioxidant-carbon black interaction, had significant effects on the thermal stability. By optimization of the percent compositions used, the best composition was obtained, 0.26%, 2.21% and 4.69% for antioxidant, carbon black and nanoclay, respectively, to achieve thermal stability equal to the targeted value of 60?minutes. X-ray diffraction confirmed a weak polymer-nanocaly interaction in the optimal sample structure. The rheology frequency sweep test showed an increase in the elastic and viscous modulus in the optimal sample relative to the control samples. The Melt Flow Index (MFI) test for an optimum sample showed a pseudo-plastic structure with the lowest melt flow index of 0.2614 g/10 min, which was consistent with the results of the complex viscosity, with the optimal sample having the highest value (128500?Pa.s). The density test indicated the most crystalline structure for the optimized sample, with the highest value (0.976?g/cm³) compared to the control samples (0.962 and 0.957?g/cm³ for the polyethylene/nanoclay and the polyethylene/carbon black sample, respectively).     

Vertically aligned α-MnO<Subscript>2</Subscript> nanosheets on carbon nanotubes as cathodic materials for aqueous rechargeable magnesium ion battery

In this work, vertically aligned α-MnO₂ nanosheets on carbon nanotubes are synthesized simply by a solution process and the electrochemical performance as host materials of magnesium ion is tested in aqueous solution. Cyclic voltammetry analysis confirms the enhanced electrochemical activity of carbon nanotube-supported samples. Moreover, carbon nanotubes skeleton could reduce the charge transfer resistant of the cathode materials, which is confirmed by electrochemical impedance spectroscopy. Furthermore, when tested as magnesium ion batteries cathodic electrode, the α-MnO₂/carbon nanotube sample registers a prominent discharge capacity of 144.6 mAh g^?1 at current density of 0.5 A g^?1, which is higher than the discharge capacity of α-MnO₂ (87.5 mAh g^?1) due to the synergistic effect of insertion/deinsertion reaction and physical adsorption/desorption process. After the 1000th cycle, a remarkable discharge capacity of 48.3 mAh g^?1 is collected for α-MnO₂/carbon nanotube at current density of 10 A g^?1, which is 85% of the original. It is found that the carbon skeleton not only improved the capacity but also enhanced the cycling performance of the α-MnO₂ electrode significantly. Therefore, α-MnO₂/carbon nanotube is a very promising candidate for further application in environmentally benign magnesium ion batteries.     

Activated carbon aerogel as electrode material for coin-type EDLC cell in organic electrolyte

Carbon aerogel (CA) was prepared by a carbonization of resorcinol–formaldehyde (RF) polymer gels, and it was chemically activated with KOH to obtain activated carbon aerogel (ACA) for electrode material for EDLC in organic electrolyte. Coin-type EDLC cells with two symmetrical carbon electrode were assembled using the prepared carbon materials. Electrochemical performance of the carbon electrodes was measured by galvanostatic charge/discharge and cyclic voltammetry methods. Activated carbon aerogel (20.9 F/g) showed much higher specific capacitance than carbon aerogel (7.9 F/g) and commercial activated carbon (8.5 F/g) at a scan rate of 100 mV/s. This indicates that chemical activation with KOH served as an efficient method to improve electrochemical performance of carbon aerogel for EDLC electrode in organic electrolyte. The enhanced electrochemical performance of activated carbon aerogel was attributed to the high effective surface area and the well-developed pore structure with appropriate pore size obtained from activation with KOH.     

Enlarging Surface/Bulk Ratios of NiO Nanoparticles toward High Utilization and Rate Capability for Supercapacitors

Reasonable design and delicate control of microstructures are critical to achieve high energy density of active materials for pseudocapacitors that seriously depend on usable reaction interface. This work shows the effect of ultrasmall particle size on enhancing utilization and rate performance of active materials. Three types of NiO nanocrystals with different sizes of 3.36, 6.24, and 7.18 nm in average diameter are uniformly distributed on mesoporous carbon nanosheets derived from corn straw piths. The nanosheets with 3.36 nm NiO particles present an extremely high NiO utilization of 93.4% (2404 F g⁻¹ at 0.5 A g⁻¹), which is 2–2.5-fold higher than materials with large sizes (6.24 and 7.18 nm). This enhancement is ascribed to more complete conversion and higher ionic/electronic conductivity from a preferable surface/bulk ratio of NiO. By coupling with commercial activated carbon, the asymmetric supercapacitors present high energy and power densities (28.53 Wh kg⁻¹ at 375 W kg⁻¹), with 78.3% capacitance retention after 10 000 cycles at 10 A g⁻¹.     

Controllable Formation of Niobium Nitride/Nitrogen‐Doped Graphene Nanocomposites as Anode Materials for Lithium‐Ion Capacitors

Niobium nitride/nitrogen‐doped graphene nanosheet hybrid materials are prepared by a simple hydrothermal method combined with ammonia annealing and their electrochemical performance is reported. It is found by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) that the as‐obtained niobium nitride nanoparticles are about 10–15 nm in size and homogeneously anchored on graphene. A non‐aqueous lithium‐ion capacitor is fabricated with an optimized mass loading of activated carbon cathode and the niobium nitride/nitrogen‐doped graphene nanosheet anode, which delivers high energy densities of 122.7–98.4 W h kg^?1 at power densities of 100–2000 W kg^?1, respectively. The capacity retention is 81.7% after 1000 cycles at a current density of 500 mA g^?1. The high energy and power of this hybrid capacitor bridges the gap between conventional high specific energy lithium‐ion batteries and high specific power electrochemical capacitors, which holds great potential applications in energy storage for hybrid electric vehicles.     

Carbon paper modified by hydrothermal ammoniated treatment for vanadium redox battery

Modification of carbon paper by hydrothermal ammoniated treatment for vanadium redox battery was investigated in this paper. The content of nitrogen in the carbon paper improved from 2.957 to 6.432 % due to the introduced of nitrogenous groups. The surface smoothness and morphology of carbon fiber did not change after the hydrothermal ammoniated treatment. In the mean time, the hydrophilicity has been enhanced because of the introduction of nitrogenous groups to the surface of carbon paper. The sample, which was treated at 220 °C for 15 h, shows the best performance in electrochemical activity and charge–discharge among all the samples. At the current density of 20 mA/cm² after 50th cycles, the coulombic efficiency, voltage efficiency, as well as energy efficiency of the fabricated cell has reached up to 97.2, 85.3, and 82.9 %, respectively. It indicates the hydrothermal ammoniated treatment might be a promising approach to modify carbon paper for vanadium redox battery.     

The preparation and characterization of olivine LiFePO4/C doped with MoO3 by a solution method

Composite Li_0.99Mo_0.01FePO4/C cathode materials were prepared by an easy solution method followed by heat-treating at various temperatures. XRD, SEM, TGA/DTA, EA, CV, XPS and charge–discharge cycles were used to evaluate the Li_0.99Mo_0.01FePO₄/C composite powders. The results indicate that mix-doping method does not affect the olivine structure of the cathode but considerably improves its capacity delivery and cycle performance. Among the prepared cathode materials, the sample heat-treated at 700 °C for 12 h shows best electrochemical performances. It shows initial specific discharge capacities of 161 and 124 mAh g^− 1 with C rates of 0.2C and 2C, respectively, which is ascribed to the enhancement of the electronic conductivity by ion doping and carbon coating.     

Binder-free composite electrodes using carbon nanotube networks as a host matrix for activated carbon microparticles

In this research, networks of single-walled carbon nanotubes (SWNTs) were used to host activated carbon (aC) microparticles to fabricate freestanding composite electrodes without the use of polymer binders. The aC-SWNT composite electrodes with up to 50 wt. % aC showed specific surface areas approaching 1000 m²/g and electrical conductivities >36 S/cm. The composite electrodes possessed the properties of both pure SWNT electrodes (e.g. low ohmic drop and rapid ion diffusion) and activated carbon particles (e.g. high specific capacitance). With an interconnected mesoporous microstructure and high electrical conductivity, the CNT networks provide an attractive alternative to polymer binders for forming freestanding electrodes for electrical energy storage devices. Here we show that micron-sized particles can be supported in this framework to utilize the performance enhancement and robustness provided by CNTs. Symmetric electrochemical capacitors fabricated with the electrodes in 6 M potassium hydroxide (KOH) aqueous electrolyte maintained specific capacitances of more than 45 F/g after 30,000 constant-current charge–discharge cycles with a current of 3.6 mA/cm².     

EDXRF determination of impurities in potassium dihydrogenphosphate single crystals and raw materials

A fast and simple preconcentration procedure for recovering various cation impurities from potassium dihydrogenphosphate (KDP) single crystals and raw materials, followed by energy‐dispersive X‐ray fluorescence analysis (EDXRF), is described. The technique is based on the adsorption of metal 8‐hydroxyquinoline complexes from aqueous solutions of KDP on activated carbon, separation of the concentrate on a Nuclepore filter and subsequent determination by EDXRF. To fix activated carbon powder on a filter surface, an amount of 1‐hexadecanol is added to the KDP solution during the preconcentration procedure. The optimum conditions for the best recovery of the impurities were established. It was shown that a preconcentration factor of 100 can be achieved and the detection limit for a number of elements was down to 0.01 µg g^?1. The relative standard deviations were 6–17% for element concentrations of 0.2 µg g^?1. The method was successfully applied to the determination of Fe, Co, Cu, Ni, Zn, Mn, Ti and Bi in KDP single crystals and raw materials. Copyright © 2005 John Wiley & Sons, Ltd.     

Improved of cathode performance of LiFePO<Subscript>4</Subscript>/C composite using different carboxylic acids as carbon sources for lithium-ion batteries

Among the several materials under development for use as a cathodes in lithium-ion batteries olivine-type LiFePO₄ is one of the most promising cathode material. However, its poor conductivity and low lithium-ion diffusion limits its practical application. In this study, we report seven different carboxylic acids used to synthesize LiFePO₄/C composite, and influences of carbon sources on electrochemical performance were intensively studied. The structure and electrochemical properties of the LiFePO₄/C were characterized by X-ray diffraction, scanning electron microscopy, electrical conductivity, and galvanostatic charge–discharge measurements. Among the materials studied, the sample E with tartaric acid as carbon source exhibited the best cell performance with a maximum discharge capacity of 160 mAh g⁻¹ at a 0.1 C-rate. The improved electrochemical properties were attributed to the reduced particle size and enhanced electrical contacts by carbon.     

Quantitative characterization of nanoparticle agglomeration within biological media

The electronics industry is one of the world??s fastest growing manufacturing industries. However, e-waste has become a serious pollution problem. This study reports the recovery of e-waste for preparing valuable MCM-48 and ordered mesoporous carbon for the first time. Specifically, this study adopts an alkali-extracted method to obtain sodium silicate precursors from electronic packaging resin ash. The influence of synthesis variables such as gelation pH, neutral/cationic surfactant ratio, hydrothermal treatment temperature, and calcination temperature on the mesophase of MCM-48 materials is investigated. Experimental results confirm that well-ordered cubic MCM-48 materials were synthesized in strongly acidic and strongly basic media. The resulting mesoporous silica had a high surface area of 1,317?m²/g, mean pore size of about 3.0?nm, and a high purity of 99.87?wt%. Ordered mesoporous carbon with high surface area (1,715?m²/g) and uniform pore size of CMK-1 type was successfully prepared by impregnating MCM-48 template using the resin waste. The carbon structure was sensitive to the sulfuric acid concentration and carbonization temperature. Converting e-waste into MCM-48 materials not only eliminates the disposal problem of e-waste, but also transforms industrial waste into a useful nanomaterial.     

Mercury removal from aqueous solution and flue gas by adsorption on activated carbon fibres

The use of two activated carbon fibres, one laboratorial sample prepared from a commercial acrylic textile fibre and one commercial sample of Kynol^®, as prepared/received and modified by reaction with powdered sulfur and H₂S gas in order to increase the sulfur content were studied for the removal of mercury from aqueous solution and from flue gases from a fluidized bed combustor. The sulfur introduced ranged from 1 to 6 wt.% depending on the method used. The most important parameter for the mercury uptake is the type of sulfur introduced rather than the total amount and it was found that the H₂S treatment of ACF leads to samples with the highest mercury uptake, despite the lower sulfur amount introduced. The modified samples by both methods can remove HgCl₂ from aqueous solutions at pH 6 within the range 290-710 mg/g (ACF) which can be favourably compared with other studies already published. The use of a filter made with an activated carbon fibre modified by powdered sulfur totally removed the mercury species present in the flue gases produced by combustion of fossil fuel.