Enhanced photocatalytic degradation of rhodamine B under visible light irradiation on mesoporous anatase TiO2 microspheres by codoping with W and N

Mesoporous anatase TiO₂ microspheres were prepared via solvothermal method. Ammonium tungstate was used as the W source, and ammonia gas flowing in an ammonothermal reactor as the N source for codoping. TiO₂:(W,N) mesoporous microspheres, which were prepared from solvothermal treatment at 160 °C for 16 h and thermal ammonolysis at 500 °C for 2 h after calcination, have high specific surface area of 106 m² g⁻¹. XPS results indicate the presence of N_O, N_i and W⁶⁺ in the codoped mesoporous TiO₂ microspheres. Monodoping with N shifts the absorption band edge of anatase TiO₂ from ultraviolet region to visible region. Although codoping with W makes the visible light absorbance decrease a little, the photocatalytic degradation of a cationic dye rhodamine B (RhB) on mesoporous TiO₂:(W,N) microspheres is increased to 1.7 times of that on mesoporous TiO₂:N microspheres. This may due to decreasing recombination centers by W-doping charge compensation.     

Enhanced photocatalytic degradation of sulfamethoxazole by stable hierarchical Fe2O3/Co3O4 heterojunction on nickel foam

A facile approach was successfully employed to prepare Fe₂O₃/Co₃O₄ nanosheet arrays on nickel foams (Fe₂O₃/Co₃O₄@NF), which owned such advantages as narrow band gap energies and high separation rate of photoexcited electron-hole pairs. The combination of Fe₂O₃ and Co₃O₄ dramatically enhanced the photocatalytic activity towards sulfamethoxazole (SMZ) degradation, with the highest catalytic efficiency of k = 0.0538 min⁻¹, which was much higher than that of Fe₂O₃@NF (0.0098 min⁻¹) and Co₃O₄@NF (0.0094 min⁻¹). The introduction of Ni foam could not only act as the support to anchor photocatalyst, but also work as the electron mediator to promote the transition of electron-hole pairs. Reactive species trapping experiments combined with electron paramagnetic resonance analysis confirmed ^•O₂⁻ was primarily responsible for SMZ degradation. Furthermore, Fe₂O₃/Co₃O₄@NF was effective and almost unaffected by inorganic cations and anions in aqueous solution. This study could provide a facile and promising path for the construction of self-supported metal oxide-based heterojunction with high efficiency and strong stability.     

Oxidative thermal degradation of LDPE and the determination of some thermodynamic quantities

The pyrolysis of polyolefin wastes is one of the possible ways to obtain chemical feedstocks. In this work, the thermal degradation of low density polyethylene, (LDPE), which is a major product within plastics, was investigated in a semi-batch reactor system. First-order rate kinetics approach was chosen and reaction rate coefficients, k, and some thermodynamic quantities determined such as activation energy, reaction enthalpy, free activation enthalpy, and entropy of degradation of LDPE for different air flow rates. We found that the maximum value of some thermodynamic quantities, such as reaction rate coefficient is 0.0243 min⁻¹ at 600 mL min⁻¹ air flow rate and the free activation enthalpy (ΔG^≠) is 148.66 kJ mol⁻¹ at 450 mL min⁻¹ air flow rate and the reaction enthalpy (ΔH^≠) is 57.65 J mol⁻¹ at 623 K temperature conditions. Moreover, we found that the oxidative degradation of LDPE is not spontaneous and has lower energy necessary (for degradation) than non-oxidative degradation processes.     

Co doped ZnO nanowires as visible light photocatalysts

High aspect ratio cobalt doped ZnO nanowires showing strong photocatalytic activity and moderate ferromagnetic behaviour were successfully synthesized using a solvothermal method and characterized by scanning electron microscopy (SEM), X-ray powder diffraction (XRD), X-ray photoelectron spectroscopy (XPS), X-ray absorption spectroscopy (XAS), vibrating sample magnetometry (VSM) and UV–visible absorption spectroscopy. The photocatalytic activities evaluated for visible light driven degradation of an aqueous methylene orange (MO) solution were higher than for Co doped ZnO nanoparticles at the same doping level and synthesized by the same synthesis route. The rate constant for MO visible light photocatalytic degradation was 1.9·10⁻³ min⁻¹ in case of nanoparticles and 4.2·10⁻³ min⁻¹ in case of nanowires. We observe strongly enhanced visible light photocatalytic activity for moderate Co doping levels, with an optimum at a composition of Zn_0.95Co_0.05O. The enhanced photocatalytic activities of Co doped ZnO nanowires were attributed to the combined effects of enhanced visible light absorption at the Co sites in ZnO nanowires, and improved separation efficiency of photogenerated charge carriers at optimal Co doping.     

Influence of N sources on the photocatalytic activity of N-doped TiO2

Influence of nitrogen precursors urea, semicarbazide and N,N’-dimethyl urea on the photocatalytic activity of the N-doped TiO₂ were studied by a simple decomposition method. The nano N-TiO₂ catalysts were synthesized via two different modified approaches by calcination at 500 °C. The synthesized samples were characterized by IR, UV-DRS, Raman, TG-DTA, XRD, EDX, XPS, SEM, TEM and BET analysis. Of the synthesized six samples of N-TiO₂ five samples showed better photocatalytic activity towards direct sunlight photo-degradation of methylene blue (MB) and rhodamine B (RhB) than Degussa P25. The catalysts obtained using semicarbazide samples F3 and F4 having large surface area of 76 and 85.8 m²/g displayed maximum photocatalytic activity. The sample F4 was 1.5 times more active than Degussa P25 for the decolourisation of MB and 1.9 times more active for the decolourisation of RhB. The presence of nitrogen, large surface area and coupling of rutile-anatase phases were found to be the main responsible factors for the enhanced photocatalytic activity. The exclusive formation of the anatase phase in the case of urea precursor is attributed to the slow evaporation of urea due to the formation of melamine derived products. The calcination temperature is the deciding factor responsible for the photocatalytic activity of the N-TiO₂ samples prepared from precursors which can potentially form the melamine and its oligomerized products on the surface of TiO₂.     

Partial oxidation of ethane to syngas in an oxygen-permeable membrane reactor

A perovskite-type oxide of Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ (BSCFO) with mixed electronic and oxygen ionic conductivity at high temperatures was used as an oxygen-permeable membrane. A tubular membrane of BSCFO made by extrusion method has been used in the membrane reactor to exclusively transport oxygen for the partial oxidation of ethane (POE) to syngas with catalyst of LiLaNiO/γ-Al₂O₃ at temperatures of 800–900 °C. After only 30 min POE reaction in the membrane reactor, the oxygen permeation flux reached at 8.2 ml cm⁻² min⁻¹. After that, the oxygen permeation flux increased slowly and it took 12 h to reach at 11.0 ml cm⁻² min⁻¹. SEM and EDS analysis showed that Sr and Ba segregations occurred on the used membrane surface exposed to air while Co slightly enriched on the membrane surface exposed to ethane. The oxygen permeation flux increased with increasing of concentration of C₂H₆, which was attributed to increasing of the driving force resulting from the more reducing conditions produced with an increase of concentration of C₂H₆ in the feed gas. The tubular membrane reactor was successfully operated for POE reaction at 875 °C for more than 100 h without failure, with ethane conversion of ∼100%, CO selectivity of >91% and oxygen permeation fluxes of 10–11 ml cm⁻² min⁻¹.     

Custom-made sulfonated poly (vinylidene fluoride-co-hexafluoropropylene) nanocomposite membranes for vanadium redox flow battery applications

Sulfonated poly (vinylidene fluoride-co-hexafluoropropylene) (SPVDF-co-HFP) based nanocomposite proton exchange membranes (PEM) are fabricated by simple solution casting method using polydopamine coated exfoliated molybdenum disulfide (PDA-MoS₂) nanosheets as an alternative for Nafion® in vanadium redox flow batteries (VRFBs). PDA-MoS₂ is synthesized by the etching of exfoliated MoS₂ nanosheets with dopamine molecule by self-polymerization method. Various characteristic results clearly demonstrated that the incorporated PDA-MoS₂ nanosheets homogeneously distributed into the SPVDF-co-HFP matrix and the presence of NH/NH₂ group electrostatically interacts with SPVDF-co-HFP to form a strong acid-base pair and thus enhances the proton transport via Grotthuss type mechanism. Besides, the improvement in surface hydrophilicity provides the vehicle type conduction also. As a result, SPVDF-co-HFP/PM nanocomposite membranes showed higher proton conductivity in comparison with the pristine membrane. Especially SPVDF-co-HFP/PM-1 membrane demonstrated the excellent proton conductivity of 5.24 × 10⁻³ Scm⁻¹ at 25 °C, lower vanadium-ion permeability of 1.05 × 10⁻⁸ cm²min⁻¹ and highest membrane selectivity of 49.9 × 10⁴ Scm⁻³min. On the other hand, vanadium-ion stability of the membrane increased by adding the PD-MoS₂ content is attributed to their strong electrostatic attraction towards the polymer matrix. Overall results suggested that the SPVDF-co-HFP/PM-1 nanocomposite membrane is found to be a better alternative for commercially costly Nafion in VRFB applications.     

Precise regulation of Ultra-thin platinum decorated Gold/Graphite carbon nitride photocatalysts by atomic layer deposition for efficient degradation of Rhodamine B under simulated sunlight

Atomic Layer Deposition (ALD) precise controlling ultra-thin platinum (Pt) modified Graphite carbon nitride (g-C₃N₄) photocatalysts, which had been doped with gold nanoparticles (Au NPs) by photodeposition, were successfully synthesized. The experimental results showed that precise regulation of platinum decorated C₃N₄-Au(C₃N₄-Au/nPt (n is the number of Pt ALD cycles, 1 Å per cycle)) exhibited excellent photocatalytic degradation ability for Rhodamine B (RhB). Under simulated sunlight irradiation, the degradation rate of 10 mg/L RhB(100 mL) by 1.5 mg C₃N₄-Au/10Pt catalysts was 95.8% within 60 min that is much better than other photocatalysts for the degradation of RhB. The efficient degradation mechanism of RhB by C₃N₄-Au/10Pt photocatalysts was studied and the experiments demonstrated the ·O₂^– as main active species played an important role in the photocatalytic process. Local surface plasmon resonance (LSPR) of Au NPs and Schottky barrier between Pt clusters and g-C₃N₄ may be the reasons for enhanced C₃N₄-Au/10Pt photocatalytic performances. Furthermore, the successive catalytic cycles revealed the excellent stability of C₃N₄-Au/10Pt photocatalyst.     

The relationship between SnII fraction and visible light activated photocatalytic activity of SnOx·SiO2 glass studied by Mössbauer spectroscopy

The relationship between local structure and visible-light photocatalytic ability of tin silicate glass prepared by sol–gel method was investigated. ¹¹⁹Sn Mössbauer spectrum of SnO_x·SiO₂ glass prepared from SnCl₂ showed a small peak of Sn^II component besides the major amount of Sn^IV. The smallest bandgap energy of 2.5 ± 0.5 eV was estimated from Tauc plot, and the largest first order rate constant (k) of (13.8 ± 0.1) 10⁻³ min⁻¹ was recorded from the methylene blue degradation test under visible-light irradiation. It is concluded that Sn^II shows remarkable photocatalytic ability when it is incorporated into silica glass matrix.

     

Biochar coupled with contrasting nitrogen sources mediated changes in carbon and nitrogen pools,microbial and enzymatic activity in paddy soil

There is limited information on changes cause by nitrogen (N) fertilizers and biochar (BC) application in soil carbon and nitrogen availability, leaching and microbial activity at different growth stages in rice. This is first comprehensive study conducted in early and late seasons during 2019 to evaluate efficiency of various traditional N fertilizers (i) Urea (ii) Ammonium nitrate and (iii) Ammonium sulfate (315 kg N ha⁻¹) with or without biochar (30 t ha⁻¹). Results illustrated that all N fertilizers sources applied with biochar significantly increased soil organic carbon (SOC) content by an average 48.44% and 50.63%, soil total nitrogen (Nt) by 4.56% and 4.94%, reduction in total nitrogen leaching by 42.63% and 76.16%, while dissolved organic carbon leaching (DOC) augmented by 39.87% and 38.38% than non-applied treatments in early and late season, respectively. Additionally, soil microbial biomass C and N progressively increased with growth stages and was found higher than non-applied treatments in both seasons. Furthermore, combined application of N fertilizers and biochar, facilitated soil N transformation and the net concentration of NH₄⁺–N and NO₃⁻–N was relatively higher than non-charred treatments. Similarly, in both early and late seasons, urease enzyme activity increased by an average 13.52% and 13.55%, β-glucosidase by 15.99% and 19.27% however, catalase activity decreased by 14.58% and 12.38%, correspondingly. Moreover, no significant difference (p < 0.05) was recorded among N fertilizers sources in both seasons.     

Enhancing the photocatalytic activity of Ga2O3–TiO2 nanocomposites using sonication amplitudes for the degradation of Rhodamine B dye

A Ga₂O₃–TiO₂ photocatalyst was synthesized by a mechanomixing method followed by a sonication technique using different amplitudes of sonication (0%, 25%, 50%, and 75% of 20 kHz). The prepared photocatalysts were characterized by X-ray diffraction, X-ray photoelectron spectroscopy, Fourier-transform infrared, Brunauer–Emmett–Teller (BET) surface area (S_BET), zeta potential, and optical techniques. Ga₂O₃–TiO₂ exhibited an excellent photocatalytic activity for Rhodamine B (RhB) dye degradation under UV irradiation. The RhB degradation rate rose linearly with the increase of sonication amplitude. The photodegradation rate (k) of the synthesized samples was calculated according to the Langmuir–Hinshelwood kinetic expression. It reached a maximum of 5.25 × 10⁻² min⁻¹ with R² of 0.99 for Ga₂O₃–TiO₂ (75%) photocatalysts. The main reactive species were detected through radical scavenging experiments. The formation of hole reactive species is the rate-determining step in the case of Ga₂O₃–TiO₂ (75%) photocatalysts.     

Successful location of tin dopant cations on surface sites of anatase-type TiO2 crystallites evidenced by 119Sn Mössbauer spectroscopic probe and XPS techniques

The present study provides the first experimental evidence for the stabilization of tin dopant cations immediately on the surface of an oxide having a tetragonal structure. ¹¹⁹Sn Mössbauer spectra of the dopant, introduced by air annealing into the bulk of anatase microcrystals, showed that it was located, in the tetravalent state, in somewhat distorted octahedral sites of a unique type. On the contrary, the reduced tin species, formed upon subsequent hydrogen annealing the Sn⁴⁺-doped samples, are found to occupy different sites being characterized by two sets of the isomer shift δ and quadrupole splitting ΔE_Q values (δ_I = 3.25 mm s⁻¹, ΔE_QI = 1.75 mm s⁻¹; and δ_II = 2.85 mm s⁻¹, ΔE_QII = 1.71 mm s⁻¹). Either of them implies both the divalent state of tin atoms and their presence at low-coordination sites that can be assigned to the surface of crystallites. Mössbauer spectra of Sn^4+←2+ daughter ions, formed upon contact with air of Sn²⁺, consist of a symmetrically broadened peak characterized by only slightly different average values of both the isomer shift (<δ> = 0.07 mm s⁻¹) and quadrupole splitting (<ΔE_Q> = 0.50 mm s⁻¹), as compared to the δ and ΔE_Q values for the bulk-located Sn⁴⁺. However, considerable broadening of Sn^4+←2+ doublet components (Γ = 0.97 mm s⁻¹) allows one to suggest that these secondary formed ions remain distributed over the non equivalent sites inherited from their Sn²⁺ precursors. The occurrence of Sn^4+←2+ at surface sites is independently proven by XPS measurements that revealed a greater than 10-fold enrichment with tin of 3–5 nm thick surface layers.     

Synthesis and photocatalytic properties of sunlight-responsive BiOBr–CoWO4 heterostructured nanocomposites

Efficient sunlight-responsive BiOBr–CoWO₄ heterostructured nanocomposite photocatalysts were prepared via a chemical precipitation route at 100°C in 4 hours. The prepared BiOBr–CoWO₄ heterostructures were characterized for phase identification, chemical composition, surface morphology, optical properties and surface area using various techniques. The X-ray diffraction pattern of the BiOBr–CoWO₄ nanocomposite was composed of diffraction peaks equivalent to both the tetragonal phase of BiOBr and the monoclinic phase of CoWO₄ nanoparticles. X-ray photoelectron spectral study of the BiOBr–CoWO₄ nanocomposite revealed orbitals of both BiOBr and CoWO₄ compounds. Transmission electron microscopy images revealed that spherical particles of CoWO₄ (20–25 nm) were dispersed on the surface of BiOBr. UV–visible–near-infrared spectral study of the BiOBr–CoWO₄ nanocomposite showed good visible-light absorption. Among the manufactured materials, BiOBr–CoWO₄-2 nanocomposite showed better charge carrier separation efficiency, as demonstrated by photoluminescence and time-resolved fluorescence. To study the practical utility of the prepared materials, their photocatalytic capability was examined for the degradation of rhodamine B (RhB) aqueous solution under sunlight irradiation. The photodegradation results showed that BiOBr–CoWO₄-2 nanocomposite degraded 98.69% RhB solution and the degradation constant was 0.067 min⁻¹, which was 5.6 and 22.5 times larger than that of pure BiOBr and CoWO₄ nanoparticles, respectively, after 60 minutes of sunlight irradiation. The superior photoactivity was facilitated by electron–hole pair separation and transfer driven by the heterostructure interface between BiOBr particles and CoWO₄ nanoparticles. The removal of RhB was initiated by photogenerated h⁺, O₂^{• −} and ^•OH reactive species based on the scavenger effect.     

CFTS-3/In2S3/SnO2:F heterojunction structure as eco-friendly photocatalytic candidate for removing organic pollutants

In this paper, quaternary chalcogenide Cu₂FeSnS₄ (CFTS) thin films were synthesized by spray pyrolysis using multilayer deposition technique in which the number (N) of sequential deposition runs (DR) is N = 1, 2, 3 and 4. The delivered volume in each sample is (N × 300 ml). Correspondingly, samples are named CFTS-N. Chemical composition, morphological, structural, optical and electrical properties were characterized using dispersive X-ray spectrometry (EDX), scanning electron microscopy (SEM), X-ray diffraction (XRD), Raman spectroscopy, spectrophotometer and Hall Effect measurements. XRD and Raman spectroscopy show a purer phase and better crystalline quality of CFTS-3 than other films. Average particle size increases with DR and reaches a maximum value of about 60 nm for N = 3. Optical results show high absorption coefficient value about 10⁵ cm⁻¹ in visible range, with an optical band gap of about 1.47 eV. Electrical resistivity of CFTS-3 equals to 5.82 10⁻³ Ω cm which is the lowest value of these four samples. We have investigated the photocatalysis activity of various thin films by measuring the degradation of methylene blue (MB) and Rhodamine (RhB) as pollutant dyes. In particular we have compared the candidates: CFTS-3/SnO₂:F, CFTS-3/In₂S₃ and CFTS-3/In₂S₃/SnO₂:F. Under sun light irradiation, CFTS-3/In₂S₃/SnO₂:F heterojunction exhibits the best photodegradation rate (96%) of MB dye.     

Determination of inorganic and total mercury by vapor generation atomic absorption spectrometry using different temperatures of the measurement cell

A simple and inexpensive laboratory-built flow injection vapor generation system coupled to atomic absorption spectrometry (FI-VG AAS) for inorganic and total mercury determination has been developed. It is based on the vapor generation of total mercury and a selective detection of Hg^2 + or total mercury by varying the temperature of the measurement cell. Only the inorganic mercury is measured when the quartz cell is at room temperature, and when the cell is heated to 650 °C or higher the total Hg concentration is measured. The organic Hg concentration in the sample is calculated from the difference between the total Hg and Hg^2 + concentrations. Parameters such as the type of acid (HCl or HNO₃) and its concentration, reductant (NaBH₄) concentration, carrier solution (HCl) flow rate, carrier gas flow rate, sample volume and quartz cell temperature, which influence FI-VG AAS system performance, were systematically investigated. The optimized conditions for Hg^2 + and total Hg determinations were: 1.0 mol l^− 1 HCl as carrier solution, carrier flow rate of 3.5 ml min^− 1, 0.1% (m/v) NaBH₄, reductant flow rate of 1.0 ml min^− 1 and carrier gas flow rate of 200 ml min^− 1. The relative standard deviation (RSD) is lower than 5.0% for a 1.0 μg l^− 1 Hg solution and the limit of quantification (LOQ, 10 s) is 55 ng g^− 1. Certified samples of dogfish muscle (DORM-1 and DORM-2) and non-certified fish samples were analyzed, using a 6.0 mol l^− 1 HCl solution for analyte extraction. The Hg^2 + and CH₃Hg⁺ concentrations found were in agreement with certified ones.     

Effective scrap iron particles (SIP) pre-treatment for complete mineralization of benzidine based azo dye effluent

This study proposed that hybrid scrap cast iron particles (SIP)-aerobic biodegradation technology could enhance the biodegradability of toxic wastewater. SIP cleaved the azo linkages of Direct Green1 dye to form benzidine, 4-aminophenol, aniline and 1,2,7-triamino-8-hydroxynapthalene-3,6-disulfonic acid. SIP-mediated dye reduction was effective at wide pH range; however, kinetic analysis revealed fastest pseudo-first order dye reduction rate at acidic pH 3 (k_d = 0.549 min⁻¹) followed by pH 9 (k_d = 0.383 min⁻¹) and pH 7 (k_d = 0.318 min⁻¹). The daughter aromatic amines produced were partially adsorbed onto the SIP surface and maximally at neutral pH. The adsorption process followed pseudo-second order adsorption kinetics and Langmuir isotherm. Benzidine was adsorbed more than 4-aminophenol and aniline. BOD₅ of the SIP-treated effluent increased from 0.93 to 12 mg/L showing improved biodegradability. The daughter amines were rapidly mineralized in the aerobic bioreactor within 6 h. Cost-effective SIP pre-treatment could accelerate mineralization and detoxification of recalcitrant wastewater.     

Photocatalytic properties of CoOx-loaded nano-crystalline perovskite oxynitrides ABO2N (A = Ca,Sr, Ba,La; B = Nb,Ta)

Highly crystalline niobium- and tantalum-based oxynitride perovskite nanoparticles were obtained from hydrothermally synthesized oxide precursors by thermal ammonolysis at different temperatures. The samples were studied with respect to their morphological, optical and thermal properties as well as their photocatalytic activity in the decomposition of methyl orange. Phase pure oxynitrides were obtained at rather low ammonolysis temperatures between 740 °C (CaNbO₂N) and 1000 °C (BaTaO₂N). Particle sizes were found to be in the range 27 nm–146 nm and large specific surface areas up to 37 m² g⁻¹ were observed. High photocatalytic activities were found for CaNbO₂N and SrNbO₂N prepared at low ammonolysis temperatures. CoO_x as co-catalyst was loaded on the oxynitride particles resulting in a strong increase of the photocatalytic activities up to 30% methyl orange degradation within 3 h for SrNbO₂N:CoO_x.     

Pulse radiolysis studies of the reactions of bromine atoms and dimethyl sulfoxide–bromine atom complexes with alcohols

Dimethylsulfoxide (DMSO)–Br complexes were generated by pulse radiolysis of DMSO/bromomethane mixtures and the formation mechanism and spectral characteristics of the formed complexes were investigated in detail. The rate constant for the reaction of bromine atoms with DMSO and the extinction coefficient of the complex were obtained to be 4.6×10⁹ M⁻¹ s⁻¹ and 6300 M⁻¹ cm⁻¹ at the absorption maximum of 430 nm. Rate constants for the reaction of bromine atoms with a series of alcohols were determined in CBrCl₃ solutions applying a competitive kinetic method using the DMSO–Br complex as the reference system. The obtained rate constants were ∼10⁸ M⁻¹ s⁻¹, one or two orders larger than those reported for highly polar solvents. Rate constants of DMSO–Br complexes with alcohols were determined to be ∼ 10⁷ M⁻¹ s⁻¹. A comparison of the reactivities of Br atoms and DMSO–Br complexes with those of chlorine atoms and chlorine atom complexes which are ascribed to hydrogen abstracting reactants strongly indicates that hydrogen abstraction from alcohols is not the rate determining step in the case of Br atoms and DMSO–Br complexes.     

Environmental remediation by an integrated microwave/UV illumination technique: VI. A simple modified domestic microwave oven integrating an electrodeless UV-Vis lamp to photodegrade environmental pollutants in aqueous media

A simple device is described based on a modified domestic microwave oven that incorporates an UV-Vis lamp encased in Teflon to photodegrade environmental pollutants in aqueous media. The performance of this device was examined using the photodegradation of the agrochemical pollutant 2,4-dichlorophenoxyacetic acid (2,4-D) as the test process driven by a coupled photocatalytic/microwave method in an aqueous TiO₂ dispersion. The aqueous dispersion was contained in a high-pressure Teflon batch (TB) reactor that also integrated a double glass cylindrical plasma lamp (DGCPL) as the source of the UV-Vis radiation. This DGCPL lamp contained mercury gas with a minute amount of neon gas and was powered solely by microwave radiation. The coupled microwave-UV-Vis irradiation of the TB-DGCPL reactor led to an enhancement of the decomposition of the 2,4-D target substrate in the modified microwave oven relative to the photocatalytic method alone. Specifically, the rates of degradation were 2×10⁻³ mM min⁻¹ (photocatalytic/microwave method (PD/MW)) and 1.1×10⁻³ mM min⁻¹ (photocatalytic method (PD)) even though the light irradiance was some six-fold greater in the latter method. That is, the coupled PD/MW method was about 10 times more efficient than the PD method alone.     

Kinetic study on preparation of substoichiometric tungsten oxide WO2.72 via hydrogen reduction process

Controlling the conditions of the oxygen partial pressure and temperature to prepare the WO_2.72 (W₁₈O₄₉) via reduction was possible through thermodynamic consideration. WO_2.72 was synthesized via heating to 1073 K in 5% H₂–95% Ar mixture gas flow from ammonium tungstate which was prepared by hydrothermal process. With the reducing prolonging time, the products were changed from WO_2.72 to WO₂ and then metal W. Thermogravimetric (TG) analysis showed ammonium tungstate decomposed completely to WO₃ at 773 K. Isothermal reductions using TG analysis were carried out at 905 K, 925 K, 945 K and 973 K in 5% H₂–95% Ar mixture gas flow, respectively. The whole reduction from WO₃ to WO_2.72 divided into three parts: initial nucleation and growth stage, final interfacial reaction stage and intermediate stage, was controlled jointly by both mechanisms. Fitting results showed that the initial stage obey the one-dimensional Avrami–Erofeev equation, the apparent activation energy was 132.7 ± 1.1 kJ mol⁻¹ and the pre-exponent factor was 4.82 × 10⁵ min⁻¹; the final stage expressed by 2-dimensional interfacial reaction, the apparent activation energy was 144.0 ± 2.1 kJ mol⁻¹ and the pre-exponent factor was 3.20 × 10⁵ min⁻¹.