用喷涂晶种法ZSM-5合成沸石膜及其影响因素考察

在多孔α－Ａｌ２Ｏ３载体上,采用喷涂方法引入一层晶种,再用水热法合成出渗透量大、气体选择分离系数高的ＺＳＭ－５沸石膜;对影响ＺＳＭ－５沸石膜合成的主要因素进行卫考察,并用ＸＲＤ,ＳＥＭ及单组分气体渗透性能测定对所合成的沸石膜进行了表征。结果表明,所合成的沸石膜是典型的ＺＳＭ－５沸石膜,膜表面晶粒排列有序,整齐地连成一致密层,绝大部分晶粒的取向一致,无较大裂缺存在,经一次合成的沸石膜的Ｈ２渗透率可达     

用水热法在铁铬铝合金片上原位合成MCM-22沸石膜

 采用水热法在铁铬铝合金片载体上原位合成了MCM-22沸石膜,并采用X射线衍射和扫描电子显微镜对沸石膜进行了表征,探讨了成膜的影响因素. 结果表明,载体预处理条件对合成沸石膜的品质有较大的影响. 载体仅经碱处理后合成的沸石膜稀疏而不连续; 载体先经碱处理再经酸处理后可得到连续致密的沸石膜,且晶片取向均一; 载体预先涂覆Al2O3胶过渡层后制得的MCM-22沸石膜经超声波清洗后不会脱落,表明沸石膜与载体间的结合力增强. 此外,增大晶化母液量有利于沸石膜的生长.     

澄清溶液体系二次生长法NaA型沸石膜的生长机制及膜厚的控制合成

用晶种涂层二次生长成膜法研究了在含水量不同的澄清溶液合成体系中NaA型沸石膜的生长及沸石膜厚度的控制合成.用SEM,TEM和XRD表征手段分析了沸石膜的形成过程和微结构.在载体表面不涂晶种而直接合成则不易形成连续沸石膜;用晶种涂层二次法可以很容易形成均匀的连续膜.合成液中水量的高低强烈影响沸石膜的生长速率、形成结构和膜的厚度.在高水量(水硅摩尔比为2000)的合成体系中沸石生长速率慢,膜主要通过晶种层中的晶粒长大,交织成膜,且膜只有一层结构;而在低水量(水硅摩尔比为750)的合成体系中沸石生长速率快,膜则通过晶种层表面晶粒向外生长、交织成膜,而膜具有两层结构.通过调变合成液的水量可有效地控制沸石膜层的厚度,并能制得非常均匀、连续的膜.     

一种气相合成Ｓilicalite—1沸石膜的新方法

由于在分离和催化领域的潜在应用前景，沸石膜近年来受到人们的广泛重视，制备沸石膜的方法很多，如原位水热合成、微波合成、电金属沉积、嵌入法等等，９０年代以来，由于可减少昂贵的模板剂用量，以及能在不同载体上合成沸石膜等优点，蒸汽相合成法（ＶＰＴ）受到关注^[1~3]，通常采用浸渍方法或正硅酸乙酯（ＴＥＯＳ）的水解在载体上形成一层致密的无定形凝胶作为引入的硅源，随即在有机模板剂和水的蒸汽相中转晶得到沸石膜，自１９９２年Ｄong等^[1]首先采用ＶＰＴ方法合成ＺＳＭ－５和ＺＳＭ－３５沸石膜以来，已经成功制备了多各结构类型的沸石膜。     

莫来石管上丝光沸石膜的合成与渗透汽化性能

采用不添加有机模板剂、配比为n_(Na_2O):n_(Al_2O_3):n_(SiO_3):n_(H_2O)=0.25:0.015～0.1:1:15～60溶胶,在涂有晶种的多孔莫来石管上水热合成出了丝光沸石膜。制备的膜经XRD和SEM表征。考察了合成时间、硅铝比、水硅比和硅源等因素对膜生长及其性能的影响。合成时间的延长有利于丝光沸石c轴方向的优先生长,然而优先取向生长膜层并未提高膜在水/乙醇分离体系中的渗透通量和选择性。优化条件下合成的膜具有较高的渗透汽化性能,在348 K、水/乙醇(10/90,W/W)混合溶液中的渗透通量和分离因子分别为0.70 kg·m~(-2)·h~(-1)。和860。基于XRD和SEM表征结果,高的渗透汽化性能可归结于在莫来石支撑层与较为疏松的表面晶体层之间形成的致密中间层。     

小晶粒丝光沸石膜的制备与表征

 以四乙基溴化铵为模板剂，硅溶胶和铝酸钠分别为硅源和铝源，用水热合成法在氧化铝载体上合成出丝光沸石膜．用扫描电镜、X射线衍射和核磁共振等手段对所制得的沸石膜进行了表征，证明其交联良好、覆盖完全、附着强度高．通过采用晶化母液老化的方法，可使丝光沸石晶体的大小从20～30μm减小到4～5μm．小晶粒丝光沸石膜的渗透分离性能与大晶粒丝光沸石膜相比有较大的提高，其H2／N2的理想分离系数从3．82提高到9．80．丝光沸石膜在醇／水混合体系中能选择性地透过水，对水／甲醇、水／乙醇、水／正丙醇和水／异丙醇体系的最大分离系数分别为2600（水的摩尔分数xw＝50％，T＝323K），5500（xw＝50％，T＝343K），6000（xw＝15％，T＝343K）和6800（xw＝50％，T＝343K）．     

Na_2O-SiO_2-Al_2O_3-NaCl-H_2O体系中ANA和SOD沸石膜的水热合成

Na2 O SiO2 Al2 O3 NaCl H2 O体系中,以水玻璃和准一水软铝石为原料,分别在堇青石和玻璃载体上水热合成方沸石(ANA)与方钠石(SOD)沸石膜.研究水含量、反应温度、反应时间与多次合成对膜结晶的影响.用XRD,SEM,EDX表征膜的晶相、形貌和化学组成.堇青石负载方沸石膜在对 95 %(wt.)乙醇水溶液的渗透蒸发实验中,水优先透过沸石膜的选择性显示了晶间孔的醇/水分离作用.非计量的NaCl进入到在玻璃载体上成膜的方钠石笼中,致使该膜显示光致变色效应     

用亚微米级晶种涂层法合成NaA沸石膜及其结构表征

 在大孔α-Al2O3陶瓷管载体上,采用亚微米级晶种涂层法在澄清溶液体系中二次生长成膜,制备了NaA沸石膜. 采用TEM,SEM和XRD等手段对晶种、陶瓷载体及沸石膜的结构、晶体形貌和成膜情况进行了表征. 结果表明,合成晶种的晶粒呈立方体,颗粒小(约150 nm)而均匀,无杂晶,可作为晶种在载体上进行预涂. 载体的孔径大而不均匀,表面粗糙不平整,直接成膜则表面仅有较少的沸石晶粒沉积,不能连续成膜. 经亚微米级晶种涂层后,载体表面形成了一层均匀、光滑的晶种层(厚度为2～3 μm); 水热晶化成膜后,膜表面晶粒相互交织生长完好,无晶间隙,所得膜致密,连续,规整,清晰,无裂缺. 该法是一种制备沸石膜的好方法.     

二次生长法NaA沸石分子筛膜的合成与表征——推荐一个研究型综合实验

介绍一个研究型综合实验——二次生长法NaA沸石分子筛膜的合成与表征。实验预先利用热浸渍法在α-Al_2O_3多孔载体管外表面引入NaA沸石分子筛晶种,再通过二次生长法合成NaA沸石分子筛膜。用扫描电子显微镜和X射线衍射仪表征载体管和NaA沸石分子筛及膜的形貌和结构,并利用渗透蒸发乙醇脱水膜分离装置测试膜的分离性能。通过本实验使学生了解膜分离技术这一科学前沿领域,激发学生对科学研究的兴趣,培养学生的科研探究能力。本实验涵盖合成、表征及性能测试,知识要点多、学科覆盖面广,有利于提升学生的实践操作能力、创新意识和综合运用知识的能力。     

二维层状沸石的合成及其催化、吸附与分离应用

与三维沸石相比,二维层状沸石具有更大的表面积、更短的扩散距离和更具韧性的结构,在许多领域中都具有更大优势。近年来,二维层状沸石的研究已成为新热点。本文基于前期文献调研总结,从两类合成角度（Bottom-up和Top-down法）归纳了近年来二维沸石的合成方法,重点综述了同种类型沸石的不同合成法的进展。此外,本文简述了二维沸石在催化、吸附和分离领域中的应用,并展望了二维沸石广阔的应用前景,以期为二维沸石的合成与应用提供参考。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.