水环境中联苯三酚的化学发光分析研究

联苯三酚对KIO4氧化异硫氰酸异鲁米诺 (ITCI)化学发光新体系有显著的增强作用 ,由此建立了一种高灵敏的测定联苯三酚的化学发光分析新体系。测定联苯三酚的线性范围为 1 75× 10 -8～ 2 5× 10 -6mol·L-1,检测限为 3 4 9× 10 -9mol·L-1,精密度为 5 6 0 % (c=5× 10 -7mol·L-1,n =9) ;用该法对自来水中的联苯三酚进行测定 ,回收率为 94 0 %～ 112 0 % ,结果令人满意     

化学发光抑制法测定抗坏血酸

利用抗坏血酸对DTMC H2 O2 化学发光体系的抑制作用 ,研究了对抗坏血酸进行间接测定的可能性。试验发现 ,化学发光猝灭率 (R)与抗坏血酸浓度在 1 0× 10 - 7～ 8 0× 10 - 6 mol·L- 1 范围内呈线性关系 ,检出限达到 8 0× 10 - 8mol·L- 1 (S N =3)。对 1 0× 10 - 6 mol·L- 1 抗坏血酸进行 10次平行测定 ,其化学发光强度猝灭率相对标准偏差为 4 6 %。该猝灭体系不需要额外的掩蔽剂 ,方法简单、选择性好 ,可直接应用于一些食品中微量抗坏血酸的测定。     

槲皮素-铁配合物的光度法研究

在 p H=4 .0 5的 HAc- NH4 Ac缓冲体系中 ,槲皮素 ( Qu)与 Fe3+配位 ,该配合物在 4 30 nm处有最大吸收。 Fe3+的浓度在 2 .0× 10 -5— 1.2× 10 -4 mol· L-1之间与吸光度成线性关系 ,最低检出限为 2 .0× 10 -5mol· L-1。测得配合物的组成为 Fe3+∶ Qu=1∶ 2 ,稳定常数 K稳 =1.0× 10 8。     

钙(Ⅱ)增敏秦皮乙素-CTMAB体系荧光特性的研究

研究了钙 ( ) -秦皮乙素 - CTMAB体系的荧光性质 ,发现 Ca2 +对秦皮乙素 - CTMAB有较强的增敏作用 ,建立了荧光光谱法测定痕量秦皮乙素的新方法。其线性范围为 2 .38× 10 -8— 2 .38× 10 -6mol· L-1;检出限为 1.2× 10 -8mol·L-1;回收率为 91.39%— 10 2 .31% ;相对标准偏差为 3.6 %。     

钼-槲皮素配合物的光度法研究

在 p H=4.72的 HAc- NH4Ac缓冲溶液中 ,槲皮素 ( Qu)能与钼 ( )生成较稳定的配合物 ,该配合物在42 2 .4nm处有最大吸收峰。Mo( )的浓度在 2 .0× 1 0 - 5— 1 .0× 1 0 - 4 mol· L- 1之间与吸光度成线性关系 ,最低检出限为 2 .0× 1 0 - 5mol· L- 1 。测得配合物的组成为 Mo( )∶ Qu=1∶ 1 ,稳定常数为 3.5× 1 0 9。     

极谱分析法连续测定痕量铅和镉

研究了 Pb2 + 和 Cd2 + 与 KCl-酒石酸钠 -三乙醇胺 -明胶体系的二次导数极谱波。在 p H=4 .5的 HAc-Na Ac介质中 ,Pb2 + 和 Cd2 + 分别于 - 0 .4 6 V和 - 0 .6 4V电位处产生一良好的极谱波。峰电流与 Pb2 + 和Cd2 + 的浓度分别在 1× 10 -5— 3× 10 -1g· L-1和 5× 10 -5— 6× 10 -3 g· L-1范围内呈线性关系。 Pb2 + 和Cd2 +的检出限分别为 1× 10 -7g·L-1和 5× 10 -7g·L-1。本法准确、简便、快速、选择性高。已直接用于饮料中铅和镉的连续测定 ,同时也对酒及面粉样品进行了测定 ,回收率分别为 99.9%— 10 0 .1%和 97.0 %—10 4 .8%。     

胶束中的若丹明6G荧光增强和激光行为

使用阴离子表面活性剂十二烷基硫酸钠 (SDS)有效的增强了若丹明 6G染料水溶液的荧光 ,在若丹明 6G浓度分别为 5 47× 10 -7和 5 47× 10 -4 mol·L-1时 ,最大增强比率分别为 1 95和 9 7。在后一浓度下SDS的加入使若丹明 6G染料激光阈值降低 ,能量转化效率提高。不加SDS时的激光阈值功率密度约为 6 5MW·cm-2 ,加入 4 1× 10 -2 mol·L-1的SDS后 ,激光阈值功率密度降为 0 8MW·cm-2 。泵浦光功率密度为 6 5MW·cm-2 时 ,能量转化效率达到 2 5 %。同时还观察到SDS的加入使溶液吸收谱、荧光谱和染料激光发生了红移。对以上现象的物理机制进行了讨论。     

中性介质中I-对鲁米诺电化学发光的增敏作用及机理研究

在中性鲁米诺电化学发光体系研究的基础上, 对中性介质中I-对鲁米诺电化学发光的增敏作用进行了研究, 结果表明, 在选定的条件下, 碘离子显著增强鲁米诺的电化学发光, 可以灵敏地对I-进行检测, 线性范围为3.8×10-7～2.2×10-6 mol·L-1, 检测下限达到4.0×10-8 mol·L-1. 该反应过程为涉及自由基的过程, 碘离子在电化学氧化过程中生成自由基, 并经过能量转移提高鲁米诺自由基的生成和激发, 提高电化学发光的量子效率, 从而起到增敏作用.     

4-(2-吡啶偶氮)-间苯二酚光度法测定煤灰中钒

在 0 .6 mol· L-1的硫酸介质中 ,钒 - PAR-羟胺生成红色络合物 ,最大吸收波长为 5 5 0 nm,摩尔吸光系数ε=1.91× 10 4L· mol-1· cm-1,钒含量在 0— 80μg/ 2 5 m L范围内符合比耳定律。本方法灵敏、简便 ,用于测定煤灰中的钒 ,结果满意     

碘金酸-阳离子表面活性剂缔合微粒体系的吸收光谱研究及分析应用

在 0 0 1mol·L-1HCl介质中 ,[AuI4]-在 35 0nm处有一吸收峰 ;当十六烷基三甲基溴化铵(CTMAB)与 [AuI4]-共存时体系呈红紫色 ,在 5 2 0nm处产生一新的吸收峰。CTMAB浓度在 0～ 7 0× 10 -5mol·L-1范围内符合比耳定律 ,回归方程为A52 0nm =0 989× 10 4cCTMAB +0 0 138,相关系数R为 0 9997,摩尔吸光系数ε为 1 0 5 8× 10 4L·mol-1·cm-1,据此建立了一种测定阳离子表面活性剂含量的分光光度新方法 ,并用于合成样品和新洁尔净样品中阳离子表面活性剂测定 ,结果满意。共振散射光谱研究表明 ,[CTMAB]+ 与 [AuI4]-可通过静电引力作用形成疏水性的 (AuI4 CTMAB)缔合物分子 ,并进一步聚集形成稳定的 (AuI4 CTMAB) n 缔合纳米微粒。由于该缔合纳米微粒在 5 80和 4 70nm处产生共振散射效应 ,故体系呈红紫色。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.