PHOTOSENSITIVITY OF Ce (Ⅳ) INITIATED METHYL ACRYLATE POLYMERIZATION

The influences of UV light irradiation (313 nm) and diffused daylight on the polymerization of methyl acrylate initiated by the ceric ammonium nitrate without any reducing agent have been studied both in aqueous nitric acid and in pure water. The rate of polymerization was found to be accelerated and the overall activation energy and the induction time were found to be decreased sharply by the UV light irradiation. Under UV light, the rate of polymerization is 8 times as high as the rate in dark. The rate of polymerization was found to attain a maximum with the increase of nitric acid concentration and the rate of polymerization became less sensitive to UV light in the presence of nitric acid whereas the induction period reduced outstandingly. Based on the experimental results, the mechanism is proposed.     

铈离子与氨基甲酸酯类化合物引发丙烯酰胺聚合的研究

本文对铈离子与苯基氨基甲酸酯类化合物在H_2O-CH_3CN(3∶1,V/V)及H_2O-HCONH_2(1∶2,V/V)两种介质中引发丙烯酰胺的聚合进行了研究。考察了不同结构的苯基氨基甲酸酯对聚合的影响。苯基氨基甲酸酯类化合物对铈离子引发聚合均有促进作用,其中对-甲苯基氨基甲酸酯的促进作用最为显著。测定了聚合反应表现活化能及聚合动力学方程,并提出了聚合反应机理。     

铈离子与乙酰苯胺及其衍生物引发丙烯酰胺聚合动力学的研究

以铈离子和酰苯胺引发体系进行丙烯酰胺的聚合,研究了不同结构酰苯胺对聚合的影响。在H_2O-CH_3CN(3∶1)介质中聚合时,乙酰对甲苯胺对聚合的促进作用最为明显,聚合速度可提高一个数量级。测定了聚合反应的表观活化能和聚合动力学方程、由聚合物的原子发射光谱,UV光谱和端基测定,提出了聚合反应机理。     

苯甲醛及其衍生物对铈离子存在下丙烯酰胺聚合的影响

<正> 虽然Santappa等早已报道Ce~(4+)(高氯酸铈)/甲醛体系能引发丙烯腈(AN)、甲基丙烯酸甲酯(MMA)的聚合,但对醛的活性以及参与引发单体聚合的自由基都未有详细报道,近来孙燕慧等发现脂肪醛能显著促进Ce~(4+)(硝酸铈铵CAN)引发丙烯酰胺(AAM)的聚合,而且醛的活性远大于相应的醇。至于芳香醛对于Ce~(4+)引发烯类单体的聚合的影响也未见详细报道。本文扼要报道苯甲醛(BA)及其衍生物对-硝基苯甲醛(PNBA)、间-硝基苯甲醛(MNBA)、间-溴苯甲醛(MBBA)、对-氯苯甲醛(PCBA)对Ce~(4+)(CAN)存在下丙烯酰胺聚合的影响,测定了其聚合速率,以UV吸收光谱、ESR波谱测定     

铈离子与4,4′-二乙酰氨基二苯基甲烷体系引发烯类聚合

四价铈离子可与多种有机还原剂组成氧化还原引发体系用于烯类聚合。Samal等报道酰胺化合物如硫代乙酰胺、丁二酰胺、乙酰胺能与铈离子匹配进行丙烯腈(AN)水溶液聚合。我们研究室发现铈离子与乙酰苯胺及其衍生物组成的体系,能顺利引发丙烯酰胺AAM聚合。本工作考察了二酰胺化合物,4,4′-二乙酰氨基二苯基甲烷     

VINYL RADICAL POLYMERIZATION INITIATED WITH CERIC ION AND N-(SUBSTITUTED PHENYL) ACETAMIDE SYSTEMS

The polymerization of acrylamide (AAM)in H_2O/DMF or in H_2O/CH_3CN mixed solvent initiated with ceric ion (Ce~(4+) )/N-(substituted phenyl)-acetamide systems have been studied. The redox polymerization was revealed by the low value of overall activation energy (E_α) of AAM polymerization using ceric ion/N-(substituted phenyl) acetamide system as an initiator. The end group of polymer formed was detected by IR spectrum analysis method, it revealed the presence of N-(m-acetoxy-methylphenyl) acetamide (m-AAe) moiety end group in the polymer obtained with ceric ion/m-AAe initiation system.     

过硫酸钾引发丙烯酰胺微乳液聚合

以山梨醇酐单月桂酸醋（Ｓｐａｎ２０）和聚氧乙烯山梨醇酐单硬醋酸酯（Ｔｗｅｅｎ６０）的混合物为乳化剂制备丙烯酰胺微乳液，研究了体系中Ｔｗｅｅｎ６０浓度、水相丙烯酰胺浓度对微乳液电导行为的影响．用过硫酸钾引发微乳液聚合，发现聚合开始后，体系电导率迅速下降，在聚合进入恒速期后电导不再降低．聚合的动力学表达式为：Ｒｐ∝［ＡＭ］１．１７［Ｅ］－１．２６［Ｉ］０．５；Ｍｖ∝［ＡＭ］１．０５［Ｅ］－０．９４［Ｉ］－０．６２．它与常规乳液聚合的动力学相差较大，却类似于悬浮聚合．     

GRAFT COPOLYMERIZATION OF ACRYLAMIDE ONTO POLY(N-PARA-TOLYLACRYLAMIDE) FILMS INITIATED BY CERIC ION

Functional monomers having phenylcarbamoyl and p-tolylcarbamoyl were synthesized. Binary initiation system consisted of Ce~(4+) and these functional monomers could initiate acrylamide polymerization. It was found that acrylamide could graft copolymerize onto macromolecules having these functional monomers units. The formation of graft copolymer has been verified by its percentage of water absorption, contact angle with water, XPS and SEM photographs. The reaction mechanism was proposed and the main reactive site of graft ocpolymerization initiated by Ce~(4+) would take place predominantly at the functional pendant group.     

辐射引发丙烯酰胺微乳液聚合

辐射引发丙烯酰胺微乳液聚合徐相凌，张志成，张曼维（中国科学技术大学应用化学系合肥２３００２６）关键词丙烯酰胺，微乳液聚合，辐射引发聚合聚丙烯酸胺（ＰＡＭ）及其共聚物是广泛应用的水溶性高分子．８０年代中期，Ｃａｎｄａｕ等’‘－”首先开始研究了丙烯酸胺的...     

UV光引发的丙烯酰胺反相乳液聚合

报道了不透明丙烯酰胺反相乳液体系的UV光引发聚合新方法 .使用普通中压汞灯并辅以适当搅拌 ,UV光引发丙烯酰胺 水 煤油 Span80 +OP 10反相乳液聚合可在 2 0min左右完成 ,所得聚合物分子量达千万 ;聚合过程中不存在恒速期 ,扫描电镜未观察到聚合前后乳胶粒径有数量级的变化 ,表明聚合反应以单体液滴成核为主 .此外 ,考察了光引发剂类型及浓度、单体浓度、乳化剂用量、反应温度等对聚合反应的影响 ,结果表明不同光引发剂的引发活性为Irgacure 2 95 9>(ITX +EDAB) >BDK ,引发剂浓度增加 ,反应速度先增加而后降低 ,存在一最大值 ;单体浓度增加 ,反应速度加快 ,聚合物分子量提高 ;乳化剂用量增加 ,反应速度加快而分子量变化不明显 ;聚合表观活化能为 13 34kJ mol.     

铈离子引发N-对甲苯基丙烯酰胺类聚合物膜上丙烯酰胺接枝共聚合的研究

合成了NTAAM,NTMAAM,NPMAAM功能单体,发现这类功能单体与铈离子组成的体系能引发丙烯酰胺聚合,带有这类功能单体的聚合物和共聚物铸成的膜,能用铈离子引发丙烯酰胺接枝共聚合。这可从反应后的膜比基膜有较大的吸水率、与水有较小的接触角,也可从扫描电子显微镜观察到表面上有凸起图象的高分子链,以及从膜表面的X射线光电子能谱所证实。同时研究了共聚物膜的组成、反应条件对接枝共聚合的影响。     

锰(Ⅲ)离子与羧酸或α-羟基羧酸体系引发丙烯酰胺聚合

锰(Ⅲ)离子可以引发烯类单体自由基聚合。羧酸,α-羟基羧酸对丙烯酰胺聚合有促进作用,其活性顺序为羟基多元羧酸(柠檬酸)>羟基羧酸(乳酸)>羧酸(正丁酸)。测定了在较高酸性([H~+]=3.0M)的硫酸水溶液中,单独Mn~(3+),Nn~(3+)-乙醇酸,Mn~(3+)-乳酸引发丙烯酰胺聚合的活化能与动力学方程。     

铈离子与乙酰乙酸乙酯体系引发烯类聚合的研究

<正> 铈离子与醇、醛、酮、α-羟基酸等组成的体系能引发烯类单体进行自由基聚合。关于铈离子与酯类化合物体系文献报道甚少。孙燕慧发现脂肪酸酯或芳香酸酯对铈离子引发丙烯酰胺(AAM)聚合能起促进作用,提高聚合速度只R_(p)但活性较小,相对聚合速度只,为1.3左右。本文研究了二元酸酯、乙酰乙酸乙酯(EACAC)分别与铈离子组成的体系引发AAM聚合,实验结果表明EACAC有很高的活性,它与铈离子组成的体系为一氧化还原引发体系。应用自由基捕捉技术和ESR波谱研究,能检测到由EACAC组分反应产生的自由基,从聚合物端基的FT-IR光谱分析,证实了该自由基能引发单体聚合而成为聚合物的端基。从而讨论了引发机理。     

铈离子/4-甲氧基丁二酰-对-甲苯胺或4-甲氧基马来酰-对-甲苯胺体系引发烯类聚合

研究了铈离子与四种不同结构的酰苯胺类化合物,如4-甲氧基丁二酰苯胺(MSA)-4-甲氧基丁二酰-对-甲苯胺(MST)、丁二酸单酰-对-甲苯胺(SAMT)和4-甲氧基马来酰-对-甲苯胺(MMT),组成的引发体系对丙烯酰胺聚合的影响,测定了聚合表现活化能和聚合反应动力学方程。由聚丙烯腈的红外光谱端基分析证实了MST组分与铈离子反应产生的自由基能引发烯类聚合。     

丙烯酰胺微乳液聚合

由乳化剂聚乙二醇壬基苯基醚ＯＰ、聚乙二醇壬基苯基醚（ＴＸ—４）、丙烯酸胺、水和煤油组成微乳液时，体系中水相丙烯酸胶浓度及体系温度对乳化剂最小量有明显的影响；而ＯＰ、ＴＸ—４比例及油水比例的影响不大．本文研究了辐射引发微乳液聚合的动力学，得到如下表达式：聚合速率及聚合物特性粘数的表观活化能分别为５３．２ＫＪ／ｍｏｌ，－３３．２ＫＪ／ｍｏｌ．聚丙烯酸胺微乳液具有特殊的增稠性能，与聚电解质增稠剂相比，电解质对增稠效果的影响不大，而其他表面活性剂的影响较大．     

STUDIES ON THE INITIATION MECHANISM OF CERIC ION AND ACETYLACETONE REDOX SYSTEM IN VINYL POLYMERIZATION

The initiation mechanism of acrylamide (AAM)polymerization using ceric ion/acetylacetone system as an initiator has been studied. The redox polymerization was revealed by the low value of overall activation energy of AAm polymerization. The structure of free radicals formed from above-mentioned initiation sytem were detected by radical trapping and ESR spectra techniques and the end groups of polymers obtained were determined by FT-IR spectra analysis method. Based on these results the initiation mechanism is proposed.     

铈盐引发聚醚氨酯膜上丙烯酰胺接枝聚合反应

由聚四亚甲基醚二醇、4,4′-二苯基甲烷二异氰酸酯与乙二胺或丁二醇扩链剂合成的聚醚氨酯薄膜,可顺利地在室温下用硝酸铈铵引发接枝丙烯酰胺共聚合反应,这可以从反应后的薄膜由起始时是透明的而变为不透明,也可以从接枝后的薄膜比基膜有较大的吸水率,以及从扫描电子显微镜观察到薄膜表面上有凸起图象的高分子链所证实,由于先发生接枝共聚合而后才是均聚反应,因而保证了接枝后的薄膜几乎不附着聚丙烯酰胺。     

铈离子与4,4′-二乙酰氨基二苯基甲烷体系引发烯类聚合

The polymerization of acrylamide was carried out in H2O-DMF (3:1 v/v) solution using eerie ion (eerie ammonium nitrate, CAN) as initiator. It was found that the presence of 4,4'-diacetaminodiphenylmethane (DAADPM) could promote the polymerization and increase the rate of polymerization. The overall activation energy and rate equation of acrylamide polymerization initiated with eerie ion/DAADPM system were determined respectively. From IR spectrum end-group analysis of polyacrylonitrile (PAN) prepared by solution polymerization of AN using CAN/DAADPM system as initiator,it revealed the presence of DAADPM end-group in the polymer. Accordingly,the initiation step includes the addition of DAADPM radical to monomer and forms the end-group of polymers.     

VINYL RADICAL POLYMERIZATION INITIATED WITH CERIC ION AND ETHYL N, N-DIETHYLDITHIOCARBAMYL ACETATE SYSTEM

Acrylamide polymerization initiated with a redox initiation system consisting of cericion and ethyl N, N-diethyldithiocarbamyl acetate (EDCA) has been studied. It was foundthat the polymerization rate equation is in good agrement with that of a redox initiatedpolymerization, and the overall activation energy of the polymerization was determinedto be 25.2kJ·mol~(-1). Accordingly, the system belongs to a redox initiator. The initiationmechanism was proposed based on the end group analysis using FT-IR, UV spectroscopies.Analysis results revealed that the N, N-diethyldithiocarbamyl radical produced from theredox reaction of EDCA with ceric ion can initiate acrylonitrile (AN) polymerization andform the end group on PAN. The resulting PAN was photopolymerized with butyl acrylate(BA) to form PAN-b-PBA block copolymer.     

丙烯酰胺双水相聚合体系稳定性研究

通过浊点滴定法测定了不同温度下PAAmPEGH2O双水相体系相图,发现分相浓度随着温度的升高先增后降,55℃时分相浓度最低.双水相聚合体系微观结构显示,分散相以砾状液滴形式均匀分散在连续相中.研究了聚合过程中聚合体系粘度的变化,以及聚合温度、分散介质、单体、引发剂及乳化剂等对聚合体系最终粘度的影响,聚合体系最终粘度在一定范围内随分散介质和单体浓度增加变化不大,但是超过某一浓度后聚合体系粘度急剧增加;聚合体系中加入少量乳化剂对体系粘度影响不大,但加入大量乳化剂后体系稳定性变差,聚合体系粘度急剧增加;聚合体系最终粘度随着聚合温度升高先降后增,与相图的预测结果一致.