石墨烯包层结构光子晶体光纤的高双折射特性

将PG玻璃材料制作成的椭圆纤芯引入光子晶体光纤中心,设计了一种石墨烯包层结构的高双折射光子晶体光纤.基于有限元法对该光纤的双折射特性进行了数值模拟,研究了光纤孔径比、孔间距和纤芯椭圆对双折射特性的影响,并以该光子晶体光纤的模场面积和限制性损耗为依据进行了优化.研究结果表明:在波长1 550nm处,光纤双折射率高达0.13,满足高双折射要求;两偏振方向模场面积小于0.7μm2,限制性损耗低于10-6 dB/km.该光纤可有效保持光在传输系统中的偏振状态,为高稳定性超连续谱的产生提供依据.     

高双折射80PbO·20Ga_2O_3中心填充光子晶体光纤特性（英文）

提出一种高折射率材料80PbO·20Ga2O3(PG玻璃)中心填充椭圆芯光子晶体光纤.基于有限元法对光子晶体光纤的双折射特性和模场面积进行数值模拟,并研究了椭圆芯尺寸、椭圆率和孔间距等光纤几何参量对双折射特性的影响.数值研究表明:在1 550nm波长处,双折射高达1.256×10-1,x偏振和y偏振模场面积分别为0.43μm2和0.68μm2;在910nm~1931nm的宽波段范围内,双折射始终保持10-1量级.该光纤可以作为保偏光纤应用于偏振控制、相干通信和光纤传感系统.     

一种基于肖特玻璃的新型高双折射光子晶体光纤

设计了一种基于肖特玻璃SF57的新型高双折射光子晶体光纤,在纤芯和包层同时引入椭圆空气孔,并且在包层的最内层对称地引入两个圆形空气孔.通过改变空气孔的间距和椭圆率,采用全矢量有限元法研究了该光纤的双折射、限制损耗和色散特性.数值研究发现,在纤芯中引入小椭圆空气孔,可极大地提高双折射的数值.通过优化光纤的结构参数,当孔间距Λ为1.60μm,椭圆率η为0.5时,在波长1.55μm处,双折射高达5.22×10-2,限制损耗低至8.82×10-10dB/m,且该光纤在1.0~2.2μm的波长范围内保持正常色散,可用于宽带色散补偿.该设计对研究新型背景材料的光子晶体光纤具有一定的意义.     

一种高双折射高非线性多零色散波长光子晶体光纤

设计了一种高双折射高非线性多零色散波长的全内反射光子晶体光纤,采用有限元法研究了这种光纤的有效模面积、非线性、色散和双折射特性.计算结果表明,通过设置合适的结构参数,该光纤可在波长1.55μm处获得2.54×10-2的双折射,也可在X,Y偏振方向分别获得50.22 W-1·km-1和54.61 W-1·km-1的高非线性系数.另外,该光纤在近红外波段出现了两个零色散波长,其中的一个零色散波长出现在1.55μm附近.本设计为获得高双折射高非线性多零色散波长的光子晶体光纤提供了一种新的结构,其在偏振控制、非线性光学、色散管理和超连续谱传输方面具有广泛的应用前景.     

椭圆空气孔矩形结构光子晶体光纤的高双折射及限制损耗分析

提出了以包层为椭圆空气孔的矩形结构光子晶体光纤,采用有限元法分析了光子晶体光纤的双折射和损耗特性.研究表明:当光子晶体光纤中心缺失两个空气孔,即Λx=1.0μm,Λy=2.0μm时,在1.55μm处双折射可以达到1.98×10-2;在芯区引入小的椭圆空气孔时,双折射与引入椭圆空气孔的大小、长短轴的比例和空气孔的位置有关;芯区引入空气孔后,使光模场发生了形变,同时减少了向包层的泄漏,其损耗相比未引入空气孔小;增加包层的层数,发现包层层数对光纤双折射和损耗几乎没有影响,当包层层数N4时,损耗小于10-3量级.     

椭圆芯非六角对称高双折射聚合物PCFs

采用全矢量平面波展开法,以聚合物PMMA为基材,研究了椭圆芯非六角对称聚合物光子晶体光纤（Photonic Crystal Fibers,PCFs）的传输模场和偏振特性,从理论上分析了其模式双折射和光纤结构参量的关系.研究结果表明,该PCFs基模的两个正交偏振态不再简并,模场呈现明显的椭圆并具有较强的线偏振特性;另外,该光纤的模式双折射强烈地依赖于光纤的结构参量,通过适当调节光纤的相对孔间距比,有望在给定波长范围内实现更高双折射单模运行.     

一种新型高双折射光子晶体光纤特性研究

设计了一种高双折射高非线性光子晶体光纤, 采用全矢量有限元法研究了这种光纤的基模模场、双折射、非线性、有效模面积及色散特性. 数值研究发现, 减小孔间距Λ的大小, 在波长1550 nm 处, 该光纤可获得10^-2 数量级的双折射B, 比普通的椭圆保偏光纤高约两个数量级; 同时, 该光纤可获得42 W^-1·km^-1 的高非线性系数γ. 另外,分别在可见光和近红外波段出现了两个零色散波长, 在波长800–2000 nm 之间具有良好的色散平坦特性. 这种设计为获得高双折射高非线性超平坦色散光子晶体光纤提供了一种新的方法, 该光纤在偏振控制、非线性光学和色散控制方面具有广泛的应用前景. 关键词： 光子晶体光纤 高双折射 高非线性 有限元法     

近椭圆内包层高双折射偏振稳定光子晶体光纤设计及特性分析

设计了一种新型近椭圆内包层(NEIC)结构的高双折射偏振保持光子晶体光纤(PCF),并利用带有各向异性完全匹配层吸收边界条件的全矢量有限元法(FEM)对这种光纤的特性参数进行了数值分析.结果表明这种结构的光子晶体光纤在1.55μm的双折射系数高达2.0×10^-3,在长轴和短轴方向上的模场直径分别为9.2μm和2.4μm.同时当短轴方向最内层空气孔的孔径在1.30—1.18μm范围内变化时(孔径变化范围～10%),其双折射系数的劣化小于1.2×10^-5,表明这种结 关键词： 光子晶体光纤 双折射 近椭圆内包层 偏振稳定性     

线双折射磁光光纤光栅中光偏振态演化

根据导波光的微扰理论得到了线双折射磁光光纤光栅中导波光耦合模方程,并给出了其解析解。借助于归一化斯托克斯参量,研究了线双折射与磁圆双折射对光纤光栅中光偏振态的影响。研究表明,线双折射磁光光纤光栅中存在左旋和右旋两个本征的椭圆光偏振态,线双折射或磁圆双折射的大小只引起本征偏振态椭圆率的变化,而不改变主轴方位角。通过调节磁光光纤光栅中两种双折射的相对大小可方便地控制输出导波光的偏振态,从而使磁光光纤光栅在光纤通信与传感中具有广泛的潜在应用。     

拉曼效应对低双折射光纤偏振特性的影响

在低双折射光纤中,利用线偏振光满足的包含拉曼效应的非线性耦合模传输方程,通过引入斯托克斯参量,导出了斯托克斯参量所满足的耦合模传输方程.利用庞加莱球图示法,描述了拉曼增益效应作用下光波偏振态的演化,研究分析了拉曼效应对低双折射光纤中光波偏振态演化规律的影响.结果表明,当输入功率与运动常量满足一定关系时,拉曼增益效应改变了光波传输时其偏振态演化周期和偏振态的椭圆率.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.     

A novel methodology for photometric compensation of projection display on patterned screen

We propose a novel methodology based on the projector-camera (ProCam) system to address the photometric compensation issue for the projection display on the patterned screen.The patterned screen is treated as the combination of a perfect white screen and a color modulator.The perfect white screen is used to automatically and accurately characterize the ProCam system offline using the polynomial model,and the parameters of the color modulator can be efficiently recovered by employing only two gray images based on the linear reflectance model.The experimental results show that the color artifacts of the display image can be greatly improved with this methodology,which demonstrates its feasibility and validity in the photometric compensation.